ON FAN5355UC02X 1.1 a / 1 a / 0.8 a, 3 mhz digitally programmable regulator Datasheet

Is Now Part of
To learn more about ON Semiconductor, please visit our website at
www.onsemi.com
Please note: As part of the Fairchild Semiconductor integration, some of the Fairchild orderable part numbers
will need to change in order to meet ON Semiconductor’s system requirements. Since the ON Semiconductor
product management systems do not have the ability to manage part nomenclature that utilizes an underscore
(_), the underscore (_) in the Fairchild part numbers will be changed to a dash (-). This document may contain
device numbers with an underscore (_). Please check the ON Semiconductor website to verify the updated
device numbers. The most current and up-to-date ordering information can be found at www.onsemi.com. Please
email any questions regarding the system integration to [email protected].
ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number
of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right
to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON
Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON
Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s
technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA
Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended
or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out
of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor
is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
FAN5355
1.1 A / 1 A / 0.8 A, 3 MHz Digitally Programmable Regulator
Features
Description
















The FAN5355 device is a high-frequency, ultra-fast transient
response, synchronous step-down DC-DC converter
optimized for low-power applications using small, low-cost
inductors and capacitors. The FAN5355 supports up to
800 mA, 1 A, or 1.1 A load current.
93% Efficiency at 3 MHz
800 mA, 1 A, or 1.1 A Output Current
I2C™-Compatible Interface up to 3.4 Mbps
6-bit VOUT Programmable from 0.75 V to 1.975 V
2.7 V to 5.5 V Input Voltage Range
3 MHz Fixed-Frequency Operation
Excellent Load and Line Transient Response
Small Size, 1 μH Inductor Solution
±2% PWM DC Voltage Accuracy
35 ns Minimum On-Time
High-Efficiency, Low-Ripple, Light-Load PFM
Smooth Transition between PWM and PFM
37 μA Operating PFM Quiescent Current
Pin-Selectable or I2C™ Programmable Output Voltage
On-the-Fly External Clock Synchronization
10-lead MLP (3 x 3 mm) or 12-bump CSP Packages
Applications







Cell Phones, Smart Phones
3G, WiFi®, WiMAX™, and WiBro® Data Cards
Netbooks®, Ultra-Mobile PCs
SmartReflex™-Compliant Power Supply
Split Supply DSPs and μP Solutions OMAP™, XSCALE™
Mobile Graphic Processors (NVIDIA®, ATI)
LPDDR2 and Memory Modules
The device is ideal for mobile phones and similar portable
applications powered by a single-cell Lithium-Ion battery. With
2
an output-voltage range adjustable via I C™ interface from
0.75 V to 1.975 V, the device supports low-voltage DSPs and
processors, core power supplies, and memory modules in
smart phones, PDAs, and handheld computers.
The FAN5355 operates at 3 MHz (nominal) fixed switching
frequency using either its internal oscillator or an external
SYNC frequency.
During light-load conditions, the regulator includes a PFM
mode to enhance light-load efficiency. The regulator
transitions smoothly between PWM and PFM modes with no
glitches on VOUT. In hardware shutdown, the current
consumption is reduced to less than 200 nA.
The serial interface is compatible with Fast/Standard and
2
High-Speed mode I C specifications, allowing transfers up to
3.4 Mbps. This interface is used for dynamic voltage scaling
with 12.5 mV voltage steps for reprogramming the mode of
operation (PFM or Forced PWM), or to disable/enable the
output voltage.
The chip's advanced protection features include short-circuit
protection and current and temperature limits. During a
sustained over-current event, the IC shuts down and restarts
after a delay to reduce average power dissipation into a fault.
During startup, the IC controls the output slew rate to minimize
input current and output overshoot at the end of soft start. The
IC maintains a consistent soft-start ramp, regardless of output
load during startup.
The FAN5355 is available in 10-lead MLP (3x3 mm) and
12-bump WLCSP packages.
All trademarks are the property of their respective owners.
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.1.7
www.fairchildsemi.com
FAN5355 — 1.1 A / 1 A / 0.8 A, 3 MHz Digitally Programmable Regulator
May 2016
Slave Address
LSB
Order Number(1)
Output
Current VOUT Programming
Power-up
Defaults
Package
Option
A1
A0
mA
Min.
Max.
VSEL0 VSEL1
FAN5355UC00X
00
0
0
800
0.7500
1.5375
1.05
1.35
WLCSP-12, 2.23 x 1.46 mm
FAN5355MP00X
00
0
0
800
0.7500
1.5375
1.05
1.35
MLP-10, 3 x 3 mm
1.05
1.20
WLCSP-12, 2.23 x 1.46 mm
(2)
FAN5355UC02X
02
1
0
800
0.7500
FAN5355UC03X
03
0
0
1000
0.7500
1.5375
1.00
1.20
WLCSP-12, 2.23 x 1.46 mm
FAN5355UC06X
06
0
0
1000
1.1875
1.9750
1.80
1.80
WLCSP-12, 2.23 x 1.46 mm
1.05
1.20
WLCSP-12, 2.23 x 1.46 mm
FAN5355UC08X
08
1
0
1100
1.4375
(2)
0.7500
1.4375
Notes:
1. The “X” designator specifies tape and reel packaging.
2. VOUT is limited to the maximum voltage for all VSEL codes greater than the maximum VOUT listed.
Typical Application
AVIN
PVIN
Q1
VIN
CIN
EN
VSEL
MODULATOR
VCCIO
VOUT
SW
SYNC
Q2
L OUT
COUT
SDA
SCL
PGND
AGND
VOUT
Figure 1. Typical Application
Table 1. Recommended External Components
Component
L1 (LOUT)
Description
1μH nominal
Vendor
Parameter
Murata LQM31P
or FDK MIPSA2520
(3)
L
Min.
Typ.
Max.
Units
0.7
1.0
1.2
μH
DCR (series R)
100
mΩ
COUT
0603 (1.6x0.8x0.8)
Murata or equivalent
10 μF X5R or better GRM188R60G106ME47D
C
(4)
5.6
10.0
12.0
μF
CIN
0603 (1.6 x 0.8 x 0.8)
Murata or equivalent
4.7 μF X5R or better GRM188R60J475KE19D
C(4)
3.0
4.7
5.6
μF
Notes:
3. Minimum L incorporates tolerance, temperature, and partial saturation effects (L decreases with increasing current).
4. Minimum C is a function of initial tolerance, maximum temperature, and the effective capacitance being reduced due to
frequency, dielectric, and voltage bias effects.
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.1.7
2
www.fairchildsemi.com
FAN5355 — 1.1 A / 1 A / 0.8 A, 3 MHz Digitally Programmable Regulator
Ordering Information
Top View
Bottom View
Top View
Figure 2. WLCSP-12, 2.23 x 1.46 mm
Figure 3. MLP10, 3 x 3 mm
Pin Definitions
Pin #
Name(5) Description
WLCSP
MLP
A1, B1
9
PGND
A2
10
SW
A3
1
PVIN
Power Input Voltage. Connect to input power source. The connection from this pin to CIN
should be as short as possible.
B2
N/A
SYNC
Sync. When toggling and SYNC_EN bit is HIGH, the regulator synchronizes to the frequency
on this pin. In PWM mode, when this pin is statically LOW or statically HIGH, or when its
frequency is outside of the specified capture range, the regulator’s frequency is controlled by
its internal 3 MHz clock.
B3
2
AVIN
Analog Input Voltage. Connect to input power source as close as possible to the input
bypass capacitor.
C1
8, PAD
AGND
Analog GND. This is the signal ground reference for the IC. All voltage levels are measured
with respect to this pin.
C2
7
EN
C3
3
SDA
D1
6
VOUT
Output Voltage Monitor. Tie this pin to the output voltage. This is a signal input pin to the
control circuit and does not carry DC current.
D2
5
VSEL
Voltage Select. When HIGH, VOUT is set by VSEL1. When LOW, VOUT is set by VSEL0. This
behavior can be overridden through I2C register settings. This pin should not be left floating.
D3
4
SCL
Power GND. Power return for gate drive and power transistors. Connect to AGND on PCB.
The connection from this pin to the bottom of CIN should be as short as possible.
Switching Node. Connect to output inductor.
Enable. When this pin is HIGH, the circuit is enabled. When LOW, quiescent current is
minimized. This pin should not be left floating.
SDA. I2C interface serial data.
SCL. I2C interface serial clock.
Note:
5. All logic inputs (SDA, SCL, SYNC, EN, and VSEL) are high impedance and should not be left floating. For minimum
2
quiescent power consumption, tie unused logic inputs to AVIN or AGND. If I C control is unused, tie SDA and SCL to AVIN.
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.1.7
3
www.fairchildsemi.com
FAN5355 — 1.1 A / 1 A / 0.8 A, 3 MHz Digitally Programmable Regulator
Pin Configuration
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above
the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended
exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings
are stress ratings only.
Symbol Parameter
VCC
Min.
Max.
Unit
AVIN, SW, PVIN Pins
-0.3
6.5
V
Other Pins
-0.3
AVIN + 0.3(6)
V
Human Body Model per JESD22-A114
3.5
KV
Charged Device Model per JESD22-C101
1.5
KV
ESD
Electrostatic Discharge
Protection Level
TJ
Junction Temperature
–40
+150
°C
TSTG
Storage Temperature
–65
+150
°C
+260
°C
TL
Lead Soldering Temperature, 10 Seconds
Note:
6. Lesser of 6.5V or AVIN+0.3V.
Recommended Operating Conditions
The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating
conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding
them or designing to absolute maximum ratings.
Symbol Parameter
VIN
f
VCCIO
Supply Voltage
Frequency Range
Min.
Max.
Unit
2.7
5.5
V
2.7
3.3
MHz
(7)
2.5
V
TA
SDA and SCL Voltage Swing
Ambient Temperature
–40
+85
°C
TJ
Junction Temperature
–40
+125
°C
Note:
2
7. The I C interface operates with tHD;DAT = 0 as long as the pull-up voltage for SDA and SCL is less than 2.5 V. If voltage
swings greater than 2.5 V are required (for example if the I2C bus is pulled up to VIN), the minimum tHD;DAT must be
2
increased to 80 ns. Most I C masters change SDA near the midpoint between the falling and rising edges of SCL, which
provides ample tHD;DAT .
Dissipation Ratings(8)
θJA(9)
Power Rating at TA ≤ 25°C
Derating Factor > TA = 25ºC
Molded Leadless Package (MLP)
49ºC/W
2050 mW
21 mW/ºC
Wafer-Level Chip-Scale Package (WLCSP)
110ºC/W
900 mW
9 mW/ºC
Package
Notes:
8.
9.
Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any
allowable ambient temperature is PD = [TJ(max) - TA ] / θJA.
This thermal data is measured with high-K board (four-layer board according to JESD51-7 JEDEC standard).
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.1.7
4
www.fairchildsemi.com
FAN5355 — 1.1 A / 1 A / 0.8 A, 3 MHz Digitally Programmable Regulator
Absolute Maximum Ratings
VIN = 3.6 V, EN = VIN, VSEL = VIN, SYNC = GND, VSEL0(6) bit = 1, CONTROL2[4:3] = 00. TA = -40°C to +85°C, unless otherwise
noted. Typical values are at TA = 25°C. Circuit and components according to Figure 1.
Symbol Parameter
Conditions
Min.
Typ.
Max.
Units
5.5
V
50
μA
Power Supplies
VIN
Input Voltage Range
IQ
Quiescent Current
ISD
Shutdown Supply Current
VUVLO
Under-Voltage Lockout Threshold
VUVHYST
Under-Voltage Lockout Hysteresis
2.7
IO = 0 mA, PFM Mode
37
IO = 0 mA, 3 MHz PWM Mode
4.8
EN = GND
0.1
2.0
EN = VIN, EN_DCDC bit = 0,
SDA = SCL = VIN
0.1
2.0
VIN Rising
VIN Falling
mA
μA
2.40
2.60
V
2.00
2.15
2.30
V
200
250
300
mV
ENABLE, VSEL, SDA, SCL, SYNC
VIH
HIGH-Level Input Voltage
VIL
LOW-Level Input Voltage
IIN
Input Bias Current
1.2
V
Input tied to GND or VIN
0.01
VIN = 3.6 V, CSP Package
145
VIN = 3.6 V, MLP Package
165
VIN = 2.7 V, MLP Package
200
0.4
V
1.00
μA
Power Switch and Protection
RDS(ON)P
ILKGP
P-Channel MOSFET On
Resistance
P-Channel Leakage Current
VDS = 6 V
1
N-Channel MOSFET On
Resistance
VIN = 3.6 V, CSP Package
75
VIN = 3.6 V, MLP Package
95
VIN = 2.7 V, MLP Package
101
ILKGN
N-Channel Leakage Current
VDS = 6 V
RDIS
Discharge Resistor for PowerDown Sequence
Options 03 and 06
RDS(ON)N
ILIMPK
P-MOS Current Limit
mΩ
μA
mΩ
1
μA
60
120
Ω
2.7 V ≤ VIN ≤ 4.2 V, Options 00 and 02
1150
1350
1600
2.7 V ≤ VIN ≤ 5.5 V, Options 00 and 02
1050
1350
1600
2.7 V ≤ VIN ≤ 4.2 V, Options 03 and 06
1350
1550
1800
2.7 V ≤ VIN ≤ 5.5 V, Options 03 and 06
1250
1550
1800
2.7 V ≤ VIN ≤ 4.5 V, Option 08
1400
1650
mA
TLIMIT
Thermal Shutdown
150
°C
THYST
Thermal Shutdown Hysteresis
20
°C
Frequency Control
fSW
Oscillator Frequency
2.65
3.00
3.35
MHz
fSYNC
Synchronization Range
2.7
3.0
3.3
MHz
DSYNC
Synchronization Duty Cycle
20
80
%
Continued on the following page…
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.1.7
5
www.fairchildsemi.com
FAN5355 — 1.1 A / 1 A / 0.8 A, 3 MHz Digitally Programmable Regulator
Electrical Specifications
VIN = 3.6 V, EN = VIN, VSEL = VIN, SYNC = GND, VSEL0(6) bit = 1, CONTROL2[4:3] = 00. TA = -40°C to +85°C, unless otherwise
noted. Typical values are at TA = 25°C. Circuit and components according to Figure 1.
Symbol Parameter
Conditions
Min.
IOUT(DC) = 0, Forced PWM, VOUT = 1.35 V
Typ.
Max.
Units
–1.5
1.5
%
–2
2
%
2.7 V ≤ VIN ≤ 5.5 V, VOUT from 0.75 to
1.5375, IOUT(DC) = 0 to 800 mA, PFM Mode
–1.5
3.5
%
IOUT(DC) = 0, Forced PWM, VOUT = 1.20 V
–1.5
1.5
%
–2
2
%
2.7 V ≤ VIN ≤ 5.5 V, VOUT from 0.75 to
1.4375, IOUT(DC) = 0 to 800 mA, PFM Mode
–1.5
3.5
%
IOUT(DC) = 0, Forced PWM, VOUT = 1.20 V
–1.5
1.5
%
2.7 V ≤ VIN ≤ 5.5 V, VOUT from 0.75 to
1.5375, IOUT(DC) = 0 to 1 A, Forced PWM
–2
2
%
2.7 V ≤ VIN ≤ 5.5 V, VOUT from 0.75 to
1.5375, IOUT(DC) = 0 to 1 A, PFM Mode
–1.5
3.5
%
IOUT(DC) = 0, Forced PWM, VOUT = 1.800 V
–1.5
1.5
%
2.7 V ≤ VIN ≤ 5.5 V, VOUT from 1.185 to
1.975, IOUT(DC) = 0 to 1 A, Forced PWM
–2
2
%
2.7 V ≤ VIN ≤ 5.5 V, VOUT from 1.185 to
1.975, IOUT(DC) = 0 to 1 A, PFM Mode
–1.5
3.5
%
IOUT(DC) = 0, Forced PWM, VOUT = 1.20 V
–1.5
1.5
%
2.7 V ≤ VIN ≤ 5.5 V, VOUT from 0.75 to
1.4375, IOUT(DC) = 0 to 1100 mA, Forced
PWM
–2
2
%
–1.5
3.5
%
Output Regulation
Option 00
Option 02
VOUT
VOUT Accuracy
Option 03
Option 06
Option 08
2.7 V ≤ VIN ≤ 5.5 V, VOUT from 0.75 to
1.5375, IOUT(DC) = 0 to 800 mA, Forced PWM
2.7 V ≤ VIN ≤ 5.5 V, VOUT from 0.75 to
1.4375, IOUT(DC) = 0 to 800 mA, Forced PWM
2.7 V ≤ VIN ≤ 5.5 V, VOUT from 0.75 to
1.4375, IOUT(DC) = 0 to 1100 mA, PFM Mode
ΔVOUT
ΔILOAD
Load Regulation
IOUT(DC) = 0 to 800 mA, Forced PWM
–0.5
%/A
ΔVOUT
ΔVIN
Line Regulation
2.7 V ≤ VIN ≤ 5.5 V, IOUT(DC) = 300 mA
0
%/V
VRIPPLE
Output Ripple Voltage
PWM Mode, VOUT = 1.35 V
2.2
mVPP
PFM Mode, IOUT(DC) = 10 mA
20
mVPP
Continued on the following page…
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.1.7
6
www.fairchildsemi.com
FAN5355 — 1.1 A / 1 A / 0.8 A, 3 MHz Digitally Programmable Regulator
Electrical Specifications (Continued)
VIN = 3.6 V, EN = VIN, VSEL = VIN, SYNC = GND, VSEL0(6) bit = 1, CONTROL2[4:3] = 00. TA = -40°C to +85°C, unless otherwise
noted. Typical values are at TA = 25°C. Circuit and components according to Figure 1.
Symbol Parameter
Conditions
Min.
Typ.
Max.
Units
0.8
LSB
6-Bit DAC
Differential Nonlinearity
Monotonicity Assured by Design
Timing
I2CEN
EN HIGH to I2C Start
tV(L-H)
VOUT LOW to HIGH Settling
μs
250
RLOAD = 75 Ω, Transition from 1.0 to
1.5375 V,
VOUT Settled to within 2% of Set Point
μs
7
Soft Start
tSS
VSLEW
Regulator
Enable to
Regulated VOUT
Option 06
RLOAD > 5 Ω, to VOUT = 1.8000 V
170
210
μs
All Other
Options
RLOAD > 5 Ω, to VOUT = Power-up Default
140
180
μs
Soft-start VOUT Slew Rate(10)
18.75
V/ms
Note:
10. Option 03 and 06 slew rates are 35.5 V/ms during the first 16 μs of soft start.
AVIN
PVIN
Q1
7-bit
DAC
EN
VSEL
SYNC
SDA
I2C
INTERFACE
AND LOGIC
SCL
VIN
CIN
REF
FPWM
VOUT
SW
SOFT START
Q2
MODULATOR
L OUT
COUT
EN_REG
PGND
CLK
VOUT
AGND
3 MHz Osc
Figure 4. Block Diagram
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.1.7
7
www.fairchildsemi.com
FAN5355 — 1.1 A / 1 A / 0.8 A, 3 MHz Digitally Programmable Regulator
Electrical Specifications (Continued)
Guaranteed by design.
Symbol
Parameter
Conditions
fSCL
SCL Clock Frequency
tBUF
Bus-Free Time between STOP and
START Conditions
Max.
Units
Standard Mode
Fast Mode
Min.
Typ.
100
400
kHz
kHz
High-Speed Mode, CB < 100 pF
3400
kHz
1700
kHz
High-Speed Mode, CB < 400 pF
tHD;STA
tLOW
START or Repeated-START Hold
Time
SCL LOW Period
Standard Mode
4.7
μs
Fast Mode
1.3
μs
4
600
160
μs
ns
ns
Standard Mode
4.7
μs
Fast Mode
1.3
High-Speed Mode, CB < 100 pF
High-Speed Mode, CB < 400 pF
160
320
μs
ns
ns
Standard Mode
Fast Mode
High-Speed Mode
Standard Mode
tHIGH
SCL HIGH Period
tSU;STA
Repeated-START Setup Time
tSU;DAT
Data Setup Time
(7)
tHD;DAT
Data Hold Time
tRCL
SCL Rise Time
tFCL
tRDA
tRCL1
tFDA
SCL Fall Time
SDA Rise Time
Rise Time of SCL After a Repeated
START Condition and After ACK Bit
SDA Fall Time
CB
Stop Condition Setup Time
4.7
Fast Mode
High-Speed Mode
Standard Mode
Fast Mode
High-Speed Mode
600
160
250
100
10
μs
ns
ns
ns
ns
ns
Standard Mode
0
3.45
Fast Mode
High-Speed Mode, CB < 100 pF
High-Speed Mode, CB < 400 pF
Standard Mode
Fast Mode
High-Speed Mode, CB < 100 pF
High-Speed Mode, CB < 400 pF
Standard Mode
Fast Mode
High-Speed Mode, CB < 100 pF
High-Speed Mode, CB < 400 pF
Standard Mode
Fast Mode
High-Speed Mode, CB < 100 pF
High-Speed Mode, CB < 400 pF
Standard Mode
Fast Mode
High-Speed Mode, CB < 100 pF
High-Speed Mode, CB < 400 pF
0
0
0
20+0.1CB
20+0.1CB
900
70
150
1000
300
80
160
300
300
40
80
1000
300
80
160
300
300
80
160
μs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
400
μs
ns
ns
pF
10
20
20+0.1CB
20+0.1CB
10
20
20+0.1CB
20+0.1CB
10
20
20+0.1CB
20+0.1CB
10
20
4
Fast Mode
High-Speed Mode
Capacitive Load for SDA and SCL
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.1.7
600
60
120
Standard Mode
Standard Mode
tSU;STO
μs
ns
ns
ns
4
Fast Mode
High-Speed Mode, CB < 100 pF
High-Speed Mode, CB < 400 pF
8
600
160
www.fairchildsemi.com
FAN5355 — 1.1 A / 1 A / 0.8 A, 3 MHz Digitally Programmable Regulator
I2C Timing Specifications
tF
tSU;STA
tBUF
SDA
tR
SCL
TSU;DAT
tHD;STO
tHIGH
tLOW
tHD;STA
tHD;DAT
tHD;STA
REPEATED
START
START
STOP
START
Figure 5. I2C Interface Timing for Fast and Slow Modes
tFDA
tRDA
REPEATED
START
tSU;DAT
STOP
SDAH
tSU;STA
tRCL1
SCLH
tFCL
tRCL
tSU;STO
tHIGH
tLOW
tHD;STA
tHD;DAT
REPEATED
START
note A
= MCS Current Source Pull-up
= RP Resistor Pull-up
Note A: First rising edge of SCLH after Repeated Start and after each ACK bit.
Figure 6. I2C Interface Timing for High-Speed Mode
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.1.7
9
www.fairchildsemi.com
FAN5355 — 1.1 A / 1 A / 0.8 A, 3 MHz Digitally Programmable Regulator
Timing Diagrams
Unless otherwise specified, Auto-PWM/PFM, VIN = 3.6 V, TA = 25°C, and recommended components as specified in Table 1.
Efficiency
100 %
100 %
90 %
90 %
80 %
80 %
70 %
Eff iciency
Efficiency
70 %
Auto PWM/PFM
60 %
Forced PWM
50 %
40 %
Forced PWM
50 %
40 %
30 %
30 %
VIN = 3.6V
VOUT = 1.05V
20 %
VIN = 3.6V
VOUT = 1.35V
20 %
10 %
10 %
0%
0%
1
10
I
LOAD
10 0
1
100 0
10
I
Ou tput Curre nt (mA)
Figure 7. Efficiency vs. Load at VOUT = 1.05 V
LOAD
100
100 0
Ou tput Curre nt (mA)
Figure 8. Efficiency vs. Load at VOUT = 1.35 V
100 %
100%
90 %
90%
80%
80 %
Auto PWM/PFM
70 %
60 %
Auto PWM/PFM
70%
Forced PWM
Eff iciency
Efficiency
Auto PWM/PFM
60 %
50 %
40 %
VIN = 3.6V
VOUT = 1.5V
30 %
Forced PWM
60%
50%
40%
VIN = 3.6V
VOUT = 1.8V
30%
20 %
20%
10 %
10%
0%
0%
1
10
I
LOAD
10 0
100 0
1
Ou tpu t Curre nt (mA)
Figure 9. Efficiency vs. Load at VOUT = 1.50 V
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.1.7
10
I
LOAD
100
1000
Output Current (mA)
Figure 10. Efficiency vs. Load at VOUT = 1.80 V
10
www.fairchildsemi.com
FAN5355 — 1.1 A / 1 A / 0.8 A, 3 MHz Digitally Programmable Regulator
Typical Performance Characteristics
1.064
1.364
1.062
1.362
1.060
1.360
1.058
VOUT (V)
VOUT (V)
Unless otherwise specified, Auto-PWM/PFM, VIN = 3.6 V, TA = 25°C, and recommended components as specified in Table 1.
Auto PWM/PFM
1.056
Forced PWM
1.054
1.358
Auto PWM/PFM
1.356
Forced PWM
1.354
1.052
1.352
1.050
1.350
1.348
1.048
1
10
100
1
1000
10
Figure 11. Load Regulation at VOUT = 1.05 V
0.10%
1.814
0.05%
Output Voltage (V)
1.812
1.810
VOUT (V)
1000
Figure 12. Load Regulation at VOUT = 1.35 V
1.816
1.808
Auto PWM/PFM
1.806
Forced PWM
1.804
0.00%
-0.05%
-0.10%
-0.15%
1.802
-0.20%
1.800
-0.25%
1.798
VIN = 2.7V
VIN = 3.6V
VIN = 5.5V
-0.30%
1
10
100
1000
-40
-20
0
I LOAD Output Current (mA)
20
40
60
80
Temperature (C)
Figure 13. Load Regulation at VOUT = 1.80 V
Figure 14. % VOUT Shift vs. Temperature (Normalized)
70
6.0
Shutdown Current (µA)
65
Quiescent Current (μA)
100
I LOAD Output Current (mA)
I LOAD Output Current (mA)
60
55
50
VSEL = 1.8V
VSEL = 0V
45
40
5.0
VSEL = 1.8V
4.0
VSEL = 0V
3.0
2.0
1.0
35
30
2.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
3.5
4.0
4.5
5.0
5.5
V IN Input Voltage (V)
VIN Input Voltage (V)
Figure 15. Quiescent Current, ILOAD = 0, EN = 1.8 V
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.1.7
3.0
Figure 16. Shutdown Current, ILOAD = 0, EN = 0
11
www.fairchildsemi.com
FAN5355 — 1.1 A / 1 A / 0.8 A, 3 MHz Digitally Programmable Regulator
Typical Performance Characteristics
Unless otherwise specified, VIN = 3.6 V, VOUT = 1.35 V, and load step tR = tF < 100 ns.
Load Transient Response
Figure 17. 50 mA to 400 mA to 50 mA, Forced PWM
Figure 18. 50 mA to 400 mA to 50 mA, Auto PWM/PFM
Figure 19. 400 mA to 750 mA to 400 mA, Auto PWM/PFM
Figure 20. 0 mA to 125 mA to 0 mA, Auto PWM/PFM
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.1.7
12
www.fairchildsemi.com
FAN5355 — 1.1 A / 1 A / 0.8 A, 3 MHz Digitally Programmable Regulator
Typical Performance Characteristics (Continued)
Unless otherwise specified, VIN = 3.6 V.
VSEL Transitions
Figure 21. Single-Step, RLOAD = 6.2 Ω
Figure 22. Single-Step, RLOAD = 6.2 Ω
Figure 23. Single-Step, RLOAD = 50 Ω
Figure 24. Single-Step, RLOAD = 50 Ω
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.1.7
13
www.fairchildsemi.com
FAN5355 — 1.1 A / 1 A / 0.8 A, 3 MHz Digitally Programmable Regulator
Typical Performance Characteristics (Continued)
Unless otherwise specified, VIN = 3.6 V.
VSEL Transitions
Figure 25. Single-Step from Forced PWM (MODE1=0),
RLOAD = 50 Ω
Figure 26. Single-Step, RLOAD = 6.2 Ω
IL
VOUT
VSEL
Figure 27. Single–Step from Auto PWM/PFM (MODE1=1),
RLOAD = 50 Ω
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.1.7
Figure 28. Multi-Step, Controlled DAC Step (9.6 mV/µs)
DEF_Slew 6 (110), 800 mA Load
14
www.fairchildsemi.com
FAN5355 — 1.1 A / 1 A / 0.8 A, 3 MHz Digitally Programmable Regulator
Typical Performance Characteristics (Continued)
RLOAD is switched with N-channel MOSFET from VOUT to GND. VIN = 3.6 V, initial VOUT = 1.35 V, initial ILOAD = 0 mA.
Short Circuit and Over-Current Fault Response
Figure 29. Metallic Short Applied at VOUT
Figure 30. Metallic Short Applied at VOUT
Figure 31. RLOAD = 660 mΩ
Figure 32. RLOAD = 660 mΩ
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.1.7
15
www.fairchildsemi.com
FAN5355 — 1.1 A / 1 A / 0.8 A, 3 MHz Digitally Programmable Regulator
Typical Performance Characteristics (Continued)
Unless otherwise specified, VIN = 3.6 V.
Figure 34. SW-Node Jitter, External Synchronization
(Infinite Persistence), ILOAD = 200 mA
Figure 33. SW-Node Jitter (Infinite Persistence),
ILOAD = 200 mA
70
PSRR
Attenuation (dB)
60
IOUT=500mA
IOUT=150mA
IOUT=20mA
50
40
30
20
10
(10)
0.1
1.0
10.0
100.0
1,000.0
Frequency (KHz)
Figure 36. VIN Ripple Rejection (PSRR)
Figure 35. Soft Start, RLOAD = 50 Ω
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.1.7
16
www.fairchildsemi.com
FAN5355 — 1.1 A / 1 A / 0.8 A, 3 MHz Digitally Programmable Regulator
Typical Performance Characteristics (Continued)
Overview
Power-Up, EN, and Soft-Start
The FAN5355 is a synchronous buck regulator that typically
operates at 3 MHz with moderate to heavy load currents. At
light load currents, the converter operates in power-saving
PFM mode. The regulator automatically transitions between
fixed-frequency PWM and variable-frequency PFM mode to
maintain the highest possible efficiency over the full range of
load current.
All internal circuits remain de-biased and the IC is in a very
low quiescent-current state until the following are true:
1.
2.
2
At that point, the IC begins a soft-start cycle, its I C interface is
enabled, and its registers are loaded with their default values.
The FAN5355 uses a very fast non-linear control architecture
to achieve excellent transient response with minimum-sized
external components.
During the initial soft start, VOUT ramps linearly to the set point
programmed in the VSEL register selected by the VSEL pin.
The soft start features a fixed output-voltage slew rate of
18.75V/ms and achieves regulation approximately 90μs after
EN rises. PFM mode is enabled during soft start until the
output is in regulation, regardless of the MODE bit settings.
This allows the regulator to start into a partially charged output
without discharging it; in other words, the regulator does not
allow current to flow from the load back to the battery.
The FAN5355 integrates an I2C-compatible interface, allowing
transfers up to 3.4 Mbps. This communication interface can be
used to:
1.
2.
3.
4.
5.
VIN is above its rising UVLO threshold, and
EN is HIGH.
Dynamically re-program the output voltage in 12.5 mV
increments.
Reprogram the mode of operation to enable or disable
PFM mode.
Control voltage transition slew rate.
Control the frequency of operation by synchronizing to an
external clock.
Enable / disable the regulator.
As soon as the output has reached its set point, the control
forces PWM mode for about 85μs to allow all internal control
circuits to calibrate.
Table 2. Soft-Start Timing (see Figure 37)
Symbol Description
2
For more details, refer to the I C Interface and Register
Description sections.
tSSDLY
Output Voltage Programming
tREG
Option(11)
VOUT Equation
00, 02, 03, 08
VOUT = 0.75 + NVSEL • 12.5mV
(1)
VOUT = 1.1875 + NVSEL • 12.5mV
(2)
06
tPOK
Time from EN to start of
soft-start ramp
Opt 03, 06
VOUT ramp
start to
Opt 00,
regulation
02, 08
PWROK (CONTROL2[5])
rising from end of tREG and
regulator stays in PWM
mode during this time
Value (μs)
75
16 +(VSEL–0.7) X 53
(VSEL–0.1) X 53
10
where NVSEL is the decimal value of the setting of the VSEL
register that controls VOUT.
Note:
11. Option 02 and 08 maximum voltage is 1.4375 V (see
Table 3).
Figure 37. Soft-Start Timing
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.1.7
17
www.fairchildsemi.com
FAN5355 — 1.1 A / 1 A / 0.8 A, 3 MHz Digitally Programmable Regulator
Circuit Description
VSEL Value
Dec Binary Hex
0 000000 00
1 000001 01
2 000010 02
3 000011 03
4 000100 04
5 000101 05
6 000110 06
7 000111 07
8 001000 08
9 001001 09
10 001010 0A
11 001011 0B
12 001100 0C
13 001101 0D
14 001110 0E
15 001111 0F
16 010000 10
17 010001 11
18 010010 12
19 010011 13
20 010100 14
21 010101 15
22 010110 16
23 010111 17
24 011000 18
25 011001 19
26 011010 1A
27 011011 1B
28 011100 1C
29 011101 1D
30 011110 1E
31 011111 1F
32 100000 20
33 100001 21
34 100010 22
35 100011 23
36 100100 24
37 100101 25
38 100110 26
39 100111 27
40 101000 28
41 101001 29
42 101010 2A
43 101011 2B
44 101100 2C
45 101101 2D
46 101110 2E
47 101111 2F
48 110000 30
49 110001 31
50 110010 32
51 110011 33
52 110100 34
53 110101 35
54 110110 36
55 110111 37
56 111000 38
57 111001 39
58 111010 3A
59 111011 3B
60 111100 3C
61 111101 3D
62 111110 3E
63 111111 3F
00, 03
0.7500
0.7625
0.7750
0.7875
0.8000
0.8125
0.8250
0.8375
0.8500
0.8625
0.8750
0.8875
0.9000
0.9125
0.9250
0.9375
0.9500
0.9625
0.9750
0.9875
1.0000
1.0125
1.0250
1.0375
1.0500
1.0625
1.0750
1.0875
1.1000
1.1125
1.1250
1.1375
1.1500
1.1625
1.1750
1.1875
1.2000
1.2125
1.2250
1.2375
1.2500
1.2625
1.2750
1.2875
1.3000
1.3125
1.3250
1.3375
1.3500
1.3625
1.3750
1.3875
1.4000
1.4125
1.4250
1.4375
1.4500
1.4625
1.4750
1.4875
1.5000
1.5125
1.5250
1.5375
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.1.7
VOUT
02, 08
0.7500
0.7625
0.7750
0.7875
0.8000
0.8125
0.8250
0.8375
0.8500
0.8625
0.8750
0.8875
0.9000
0.9125
0.9250
0.9375
0.9500
0.9625
0.9750
0.9875
1.0000
1.0125
1.0250
1.0375
1.0500
1.0625
1.0750
1.0875
1.1000
1.1125
1.1250
1.1375
1.1500
1.1625
1.1750
1.1875
1.2000
1.2125
1.2250
1.2375
1.2500
1.2625
1.2750
1.2875
1.3000
1.3125
1.3250
1.3375
1.3500
1.3625
1.3750
1.3875
1.4000
1.4125
1.4250
1.4375
1.4375
1.4375
1.4375
1.4375
1.4375
1.4375
1.4375
1.4375
The EN_DCDC bit, VSELx[7] can enable the regulator in
conjunction with the EN pin. Setting EN_DCDC with EN HIGH
begins the soft-start sequence described above.
06
1.1875
1.2000
1.2125
1.2250
1.2375
1.2500
1.2625
1.2750
1.2875
1.3000
1.3125
1.3250
1.3375
1.3500
1.3625
1.3750
1.3875
1.4000
1.4125
1.4250
1.4375
1.4500
1.4625
1.4750
1.4875
1.5000
1.5125
1.5250
1.5375
1.5500
1.5625
1.5750
1.5875
1.6000
1.6125
1.6250
1.6375
1.6500
1.6625
1.6750
1.6875
1.7000
1.7125
1.7250
1.7375
1.7500
1.7625
1.7750
1.7875
1.8000
1.8125
1.8250
1.8375
1.8500
1.8625
1.8750
1.8875
1.9000
1.9125
1.9250
1.9375
1.9500
1.9625
1.9750
Table 4. EN_DCDC Behavior
EN_DCDC Bit
EN Pin
I2C
REGULATOR
0
1
1
0
0
1
0
1
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
Light-Load (PFM) Operation
The FAN5355 offers a low-ripple, single-pulse PFM mode to
save power and improve efficiency when the load current is
very low. PFM operation features:



Smooth transitions between PFM and PWM modes
Single-pulse operation for low ripple
Predictable PFM entry and exit currents.
PFM begins after the inductor current has become
discontinuous, crossing zero during the PWM cycle in 32
consecutive cycles. PFM exit occurs when discontinuous
current mode (DCM) operation cannot supply sufficient current
to maintain regulation. During PFM mode, the inductor current
ripple is about 40% higher than in PWM mode. The load
current required to exit PFM mode is thereby about 20%
higher than the load current required to enter PFM mode,
providing sufficient hysteresis to prevent “mode chatter.”
While PWM ripple voltage is typically less than 4mVPP, PFM
ripple voltage can be up to 30 mVPP during very light load. To
prevent significant undershoot when a load transient occurs,
the initial DC set point for the regulator in PFM mode is set
10 mV higher than in PWM mode. This offset decays to about
5 mV after the regulator has been in PFM mode for ~100 μs.
The maximum instantaneous voltage in PFM is 30 mV above
the set point.
PFM mode can be disabled by writing to the mode control bits:
CONTROL1[3:0] (see Table 1 for details).
Some vendors provide both “Light PFM” (LPFM) and “Fast
PFM” (FPFM) modes, while the FAN5355 provides only one
PFM mode. The FAN5355’s single PFM mode features the
fast transient recovery of FPFM, but does this with the low
quiescent current consumption similar to LPFM mode.
18
www.fairchildsemi.com
FAN5355 — 1.1 A / 1 A / 0.8 A, 3 MHz Digitally Programmable Regulator
Software Enable
Table 3. VSEL vs. VOUT
Multi-Step Mode:
Applies to Options 03 and 06 only.
The nominal internal oscillator frequency is 3 MHz. The
regulator runs at its internal clock frequency until these
conditions are met:
1. EN_SYNC bit, CONTROL1[5], is set; and
2. A valid frequency appears on the SYNC pin.
The internal DAC is stepped at a rate defined by DEFSLEW,
CONTROL2[2:0], ranging from 000 to 110. This mode
minimizes the current required to charge COUT and thereby
minimizes the current drain from the battery when
transitioning. The PWROK bit, CONTROL2[5], remains LOW
until about 1.5 μs after the DAC completes its ramp.
Table 5. SYNC
Frequency
fOSC(INTERNAL)=3.0 MHz
Validation
CONTROL2
for
VHIGH
fSYNC Valid
PLL_MULT
fSYNC Divider
Min.
Typ.
Max.
00
1
1.80
3.00
4.00
01
2
0.90
1.50
2.00
10
3
0.60
1.00
1.33
11
4
0.45
0.75
1.00
VOUT
VLOW
VSEL
If the EN_SYNC is set and SYNC fails validation, the regulator
continues to run at its internal oscillator frequency. The
regulator is functional if fSYNC is valid, as defined in Table 5,
but its performance is compromised if fSYNC is outside the fSYNC
window in the Electrical Specifications.
Figure 38. Multi-Step VOUT Transition
Single-Step Mode:
Used if DEFSLEW, CONTROL2[2:0] = 111. The internal DAC
is immediately set to the higher voltage and the regulator
performs the transition as quickly as its current-limit circuit
allows, while avoiding excessive overshoot.
When CONTROL1[3:2] = 00 and the VSEL line is LOW, the
converter operates according to the MODE0 bit,
CONTROL1[0], with synchronization disabled regardless of
the state of the EN_SYNC and HW_nSW bits.
Figure 39 shows single-step transition timing. tV(L-H) is the time
it takes the regulator to settle to within 2% of the new set point
and is typically 7 μs for a full-range transition (from 000000 to
111111). The PWROK bit, CONTROL2[5], goes LOW until the
transition is complete and VOUT settled. This typically occurs
~2 μs after tV(L-H).
Output Voltage Transitions
The IC regulates VOUT to one of two set point voltages, as
determined by the VSEL pin and the HW_nSW bit.
Table 6. VOUT Set Point and Mode Control MODE_CTRL,
CONTROL1[3:2] = 00
VSEL Pin
HW_nSW Bit
VOUT Set Point
PFM
0
1
x
1
1
0
VSEL0
VSEL1
VSEL1
Allowed
Per MODE1
Per MODE1
tPOK(L-H)
PWROK
It is good practice to reduce the load current before making
positive VSEL transitions. This reduces the time required to
make positive load transitions and avoids current-limit-induced
overshoot.
VHIGH
98% VHIGH
If HW_nSW = 0, VOUT transitions are initiated through the
following sequence:
1. Write the new setpoint in VSEL1.
2. Write desired transition rate in DEFSLEW,
CONTROL2[2:0], and set the GO bit in CONTROL2[7].
VOUT
If HW_nSW = 1, VOUT transitions are initiated either by
changing the state of the VSEL pin or by writing to the VSEL
register selected by the VSEL pin.
PWROK
VLOW
VSEL
tPOK(L-H)
Figure 39. Single-Step VOUT Transition
Positive Transitions
When transitioning to a higher VOUT, the regulator can perform
the transition using multi-step or single-step mode.
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.1.7
tV(L-H)
All positive VOUT transitions inhibit PFM until the transition is
complete, which occurs at the end of tPOK(L-H).
19
www.fairchildsemi.com
FAN5355 — 1.1 A / 1 A / 0.8 A, 3 MHz Digitally Programmable Regulator
Switching-Frequency Control and
Synchronization
When moving from VSEL=1 to VSEL=0, the regulator enters
PFM mode, regardless of the condition of the SYNC pin or
MODE bits, and remains in PFM until the transition is
completed. Reverse current through the inductor is blocked,
and the PFM minimum frequency control inhibited, until the
new set point is reached, at which time the regulator resumes
control using the mode established by MODE_CTRL. The
transition time from VHIGH to VLOW is controlled by the load
current and output capacitance as:
t V (H−L ) = COUT •
VHIGH − VLOW
ILOAD
The FAN5355’s serial interface is compatible with standard,
fast, and HS mode I2C bus specifications. The FAN5355’s
SCL line is an input and its SDA line is a bi-directional opendrain output; it can only pull down the bus when active. The
SDA line only pulls LOW during data reads and when
signaling ACK. All data is shifted in MSB (bit 7) first.
SDA and SCL are normally pulled up to a system I/O power
supply (VCCIO), as shown in Figure 1. If the I2C interface is
not used, SDA and SCL should be tied to AVIN to minimize
quiescent current consumption.
(3)
Addressing
VHIGH
FAN5355 has four user-accessible registers:
Table 7. I2C Register Addresses
Address
VOUT
VLOW
VSEL
PWROK
tV(L-H)
VSEL0
VSEL1
CONTROL1
CONTROL2
tPOK(L-H)
Figure 40. Negative VOUT Transition
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
1
0
1
Slave Address
Protection Features
In Table 8, A1 and A0 are according to the Ordering
Information table on page 2.
Current Limit / Auto-Restart
The regulator includes cycle-by-cycle current limiting, which
prevents the instantaneous inductor current from exceeding
the current-limit threshold.
Table 8.
The IC enters “fault” mode after sustained over-current. If
current limit is asserted for more than 32 consecutive cycles
(about 20 μs), the IC returns to shut-down state and remains
in that condition for ~80 μs. After that time, the regulator
attempts to restart with a normal soft-start cycle. If the fault
has not cleared, it shuts down ~10 μs later.
7
6
5
4
3
2
1
0
1
0
0
1
0
A1
A0
R/ W
Bus Timing
As shown in Figure 41, data is normally transferred when SCL
is LOW. Data is clocked in on the rising edge of SCL.
Typically, data transitions shortly at or after the falling edge of
SCL to allow ample time for the data to set up before the next
SCL rising edge.
If the fault is a short circuit, the initial current limit is ~30% of
the normal current limit, which produces a very small drain on
the system power source.
Data change allowed
Thermal Protection
SDA
When the junction temperature of the IC exceeds 150°C, the
device turns off all output MOSFETs and remains in a low
quiescent-current state until the die cools to 130°C before
commencing a normal soft-start cycle.
TH
SCL
Under-Voltage Lockout (UVLO)
TSU
Figure 41. Data Transfer Timing
The IC turns off all MOSFETs and remains in a very low
quiescent-current state until VIN rises above the UVLO
threshold.
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.1.7
2
I C Slave Address
Each bus transaction begins and ends with SDA and SCL
HIGH. A transaction begins with a “START” condition, which is
defined as SDA transitioning from 1 to 0 with SCL HIGH, as
shown in Figure 42.
20
www.fairchildsemi.com
FAN5355 — 1.1 A / 1 A / 0.8 A, 3 MHz Digitally Programmable Regulator
I2C Interface
Negative Transitions
The master then generates a repeated-start condition (Figure
44) that causes all slaves on the bus to switch to HS mode.
The master then sends I2C packets, as described above,
using the HS-mode clock rate and timing.
Slave Address
MS Bit
SCL
The bus remains in HS mode until a stop bit (Figure 43) is
sent by the master. While in HS mode, packets are separated
by repeated-start conditions (Figure 44).
Figure 42. Start Bit
Slave Releases
A transaction ends with a “STOP” condition, which is defined
as SDA transitioning from 0 to 1 with SCL HIGH, as shown in
Figure 43.
Slave Releases
Master Drives
SDA
tHD;STA
SLADDR
MS Bit
SCL
tHD;STO
ACK(0) or
NACK(1)
SDA
tSU;STA
ACK(0) or
NACK(1)
Figure 44. Repeated-Start Timing
Read and Write Transactions
SCL
The following figures outline the sequences for data read and
write. Bus control is signified by the shading of the packet,
Figure 43. Stop Bit
Table 9.
The protocols for High-Speed (HS), Low-Speed (LS), and
Fast-Speed (FS) modes are identical, except the bus speed
for HS mode is 3.4 MHz. HS mode is entered when the bus
master sends the HS master code 00001XXX after a start
condition. The master code is sent in FS mode (less than
400 KHz clock) and slaves do not ACK this transmission.
A
7 bits
0
Slave Drives Bus
.
I2C Bit Definitions for Figure 45 - Figure 46
Symbol Definition
S
Slave Address
and
All addresses and data are MSB first.
High-Speed (HS) Mode
S
Master Drives Bus
defined as
During a read from the FAN5355 (Figure 46), the master
issues a “Repeated Start” after sending the register address
and before resending the slave address. The “Repeated Start”
is a 1 to 0 transition on SDA while SCL is HIGH, as shown in
Figure 44.
START, see Figure 42.
ACK. The slave drives SDA to 0 to acknowledge
the preceding packet.
NACK. The slave sends a 1 to NACK the
preceding packet.
Repeated START, see Figure 44.
STOP, see Figure 43.
A
R
P
0
8 bits
0
8 bits
0
A
Reg Addr
A
Data
A
P
Figure 45. Write Transaction
7 bits
S
Slave Address
0
0
8 bits
0
A
Reg Addr
A
7 bits
R
Slave Address
1
0
8 bits
1
A
Data
A
P
Figure 46. Read Transaction
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.1.7
21
www.fairchildsemi.com
FAN5355 — 1.1 A / 1 A / 0.8 A, 3 MHz Digitally Programmable Regulator
THD;STA
SDA
Default Values
Each option of the FAN5355 (see Ordering Information on page 2) has different default values for the some of the register bits.
Table 10 defines both the default values and the bit’s type (as defined in Table 11) for each available option.
Table 10. Default Values and Bit Types for VSEL and CONTROL Registers
VSEL0
VSEL1
Option
7
6
5
4
3
2
1
0
VOUT
Option
7
6
5
4
3
2
1
0
VOUT
00
02
03
06
08
1
1
1
1
1
1
1
1
1
1
0
0
0
1
0
1
1
1
1
1
1
1
0
0
1
0
0
1
0
0
0
0
0
0
0
0
0
0
1
0
1.05
1.05
1.00
1.80
1.05
00
02
03
06
08
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
1
0
0
0
0
0
0
0
1
1
0
1
0
0
0
0
0
0
0
0
1
0
1.35
1.20
1.20
1.80
1.20
CONTROL1
CONTROL2
Option
7
6
5
4
3
2
1
0
Option
7
6
5
4
3
2
1
0
00, 02, 08
03, 06
1
1
0
0
0
0
1
1
0
0
0
0
0
0
0
0
00, 02, 08
03, 06
0
0
0
0
1
1
0
0
0
0
1
1
1
1
1
1
Table 11. Bit-Type Definitions for Table 10
#
#
#
Active bit.
Disabled.
Read-only.
Changing this bit changes the behavior of the converter, as described below.
Converter logic ignores changes made to this bit. Bit can be written to and read-back.
2
Writing to this bit through I C does not change the read-back value, nor does it change converter behavior.
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.1.7
22
www.fairchildsemi.com
FAN5355 — 1.1 A / 1 A / 0.8 A, 3 MHz Digitally Programmable Regulator
Register Descriptions
The following table defines the operation of each register bit. Superscript characters define the default state for each option.
0,2,3,6,8
signify the default values for options 00, 02, 03, 06, and 08 respectively. A signifies the default for all options.
Superscripts
Bit Name
Value
VSEL0
7
EN_DCDC
6
5:0
Reserved
DAC[5:0]
0
A
1
1
Table 10
VSEL1
7
6
5:0
EN_DCDC
Reserved
DAC[5:0]
CONTROL1
7:6
Reserved
0
A
1
1
Table 10
10
0
5
EN_SYNC
4
HW_nSW
3:2 MODE_CTRL
1
MODE1
0
MODE0
A
A
1
0
A
1
A
00
01
10
11
A
0
1
A
0
1
CONTROL2
A
7
GO
6
OUTPUT_
DISCHARGE
5
PWROK
(read only)
4:3
PLL_MULT
2:0
DEFSLEW
0
1
A
0
1
0
1
A
00
01
10
11
000
001
010
011
100
101
110
A
111
Description
Register Address: 00
Device in shutdown regardless of the state of the EN pin. This bit is mirrored in VSEL1. A write to bit 7 in
either register establishes the EN_DCDC value.
Device enabled when EN pin is HIGH, disabled when EN is LOW.
6-bit DAC value to set VOUT.
Register Address: 01
Device in shutdown regardless of the state of the EN pin. This bit is mirrored in VSEL0. A write to bit 7 in
either register establishes the EN_DCDC value.
Device enabled when EN pin is HIGH, disabled when EN is LOW.
6-bit DAC value to set VOUT.
Register Address: 02
Vendor ID bits. Writing to these bits has no effect on regulator operation. These bits can be used to
2
distinguish between vendors via I C.
Disables external signal on SYNC from affecting the regulator.
When a valid frequency is detected on SYNC, the regulator synchronizes to it and PFM is disabled, except
when MODE = 00, VSEL pin = LOW, and HW_nSW = 1.
VOUT is controlled by VSEL1. Voltage transitions occur by writing to the VSEL1, then setting the GO bit.
VOUT is programmed by the VSEL pin. VOUT = VSEL1 when VSEL is HIGH, and VSEL0 when VSEL is LOW.
Operation follows MODE0, MODE1.
PFM with automatic transitions to PWM, regardless of VSEL.
PFM disabled (forced PWM), regardless of VSEL.
Unused.
PFM disabled (forced PWM) when regulator output is controlled by VSEL1.
PFM with automatic transitions to PWM when regulator output is controlled by VSEL1.
PFM with automatic transitions to PWM when VSEL is LOW. Changing this bit has no effect on the
operation of the regulator.
Register Address: 03
This bit has no effect when HW_nSW = 1.
Starts a VOUT transition if HW_nSW = 0. This bit must be written by the external master to 1 for the next
VOUT transition to start, even if its value might have already been 1 from the last VOUT transition.
When the regulator is disabled, VOUT is not discharged.
When the regulator is disabled, VOUT discharges through an internal pull down.
VOUT is not in regulation or is in current limit.
VOUT is in regulation.
fSW = fSYNC when synchronization is enabled.
fSW = 2 X fSYNC when synchronization is enabled.
fSW = 3 X fSYNC when synchronization is enabled.
fSW = 4 X fSYNC when synchronization is enabled.
VOUT slews at 0.15 mV/μs during positive VOUT transitions.
VOUT slews at 0.30 mV/μs during positive VOUT transitions.
VOUT slews at 0.60 mV/μs during positive VOUT transitions.
VOUT slews at 1.20 mV/μs during positive VOUT transitions.
VOUT slews at 2.40 mV/μs during positive VOUT transitions.
VOUT slews at 4.80 mV/μs during positive VOUT transitions.
VOUT slews at 9.60 mV/μs during positive VOUT transitions.
Positive VOUT transitions use single-step mode (see Figure 39).
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.1.7
23
www.fairchildsemi.com
FAN5355 — 1.1 A / 1 A / 0.8 A, 3 MHz Digitally Programmable Regulator
Bit Definitions
Product-Specific Dimensions
Product
D
E
X
Y
FAN5355UC
2.200 ±0.030
1.430 ±0.030
0.220
0.355
© 2008 Fairchild Semiconductor Corporation
FAN5355 • Rev. 1.1.7
24
www.fairchildsemi.com
FAN5355 — 1.1 A / 1 A / 0.8 A, 3 MHz Digitally Programmable Regulator
The table below pertains to the Marketing outline drawing on the following page.
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
© Semiconductor Components Industries, LLC
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
1
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
www.onsemi.com