MULTIANODE PHOTOMULTIPLIER TUBE ASSEMBLY H8711, H8711-10 PATENT 4 mm × 4 mm Multianode, High Speed Response, Low Cross-talk 30 mm Square, Bialkali Photocathode, 12-stage, Head-on Type GENERAL Parameter Spectral Response Peak Wavelength Photocathode Material Minimum Effective Area Window Material Dynode Structure Number of Stages Anode Size Weight Operating Ambient Temperature Storage Temperature Description/Value 300 to 650 420 Bialkali 18.1 × 18.1 Borosilicate glass Metal channel dynode 12 4.2 × 4.2 (center) Approx. 50 -30 to +50 -30 to +50 Unit nm nm — mm — — — mm g °C °C Value 1000 0.014* Unit V mA MAXIMUM RATINGS (Absolute Maximum Values) Parameter Supply Voltage Between Anode and Cathode Average Anode Output Current in Total * The maximum average anode current is defined as 5 % of divider current when standard high voltage is applied. CHARACTERISTICS (at 25 °C) Cathode Sensitivity Anode Sensitivity Parameter Luminous (2856 K) Blue Sensitivity Index (CS 5-58) Luminous (2856 K) Min. 60 6.5 80 (20) Gain — Anode Dark Current per Channel (after 30 min storage in darkness) Anode Dark Current in Total (after 30 min storage in darkness) Anode Pulse Rise Time Time Response Electron Transit Time per Channel Transit Time Spread (FWHM) Pulse Linearity per Channel (±5 % deviation) Cross-talk (4 mm × 4 mm Aperture) Uniformity Between Each Anode — — — — — — — — Typ. 80 8.5 280 (70) 3.5 × 106 (0.9 × 106) 0.8 (0.4) 12 (6) 0.83 10.9 0.3 1 (3) 1 1: 3 Max. — — — Unit µA/lm — A/lm — — — 60 (30) — — — — — 1: 5 nA nA ns ns ns mA % — NOTE: Anode characteristics are measured with the voltage distribution ratio shown below. ( ): Measured with the special voltage distribution ratio (Tapered Divider) shown below. VOLTAGE DISTRIBUTION RATIO AND SUPPLY VOLTAGE Electrodes K Dy1 Dy2 Dy3 Dy4 Dy5 H8711 2 2 2 1 1 H8711-10 (Tapered Divider) 2.4 2.4 2.4 1 1 Supply Voltage: 800 V, K: Cathode, Dy: Dynode, P: Anode ... 1 ... 1 1 ... 1 Dy9 Dy10 1 1 Dy11 1 1 Dy12 P 1 1 1.2 2.4 Subject to local technical requirements and regulations, availability of products included in this promotional material may vary. Please consult with our sales office. Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. ©2003 Hamamatsu Photonics K.K. MULTIANODE PHOTOMULTIPLIER TUBE ASSEMBLIES H8711, H8711-10 Figure 2: Typical Gain and Anode Dark Current per Channel TPMHB0266EA 108 CATHODE RADIANT SENSITIVITY TPMHB0690EA 10 103 106 7 H8 0 105 1 102 11 GAIN QUANTUM EFFICIENCY H 1 87 1 1− 101 104 100 11 87 H 103 102 200 300 400 500 600 700 800 ANODE DARK CURRENT PER CHANNEL 101 400 900 600 Figure 4: Typical T.T.S. Characteristic TPMHB0331EA TPMHB0314EB RELATIVE COUNTS 104 SUPPLY VOLTAGE = -800 V RISE TIME = 835 ps FALL TIME = 2047 ps WIDTH = 1658 ps RL = 50 Ω SUPPLY VOLTAGE= - 800 V FWHM= 310 ps FWTM= 631 ps 103 102 101 100 TIME (2 ns/div.) 800 SUPPLY VOLTAGE (V) WAVELENGTH (nm) Figure 3: Typical Time Response 0 −1 11 7 H8 0.1 0.01 100 (2 mV/div.) 104 107 GAIN CATHODE RADIANT SENSITIVITY (mA/W) QUANTUM EFFICIENCY (%) 100 TIME (0.5 ns/div.) 10-1 10-2 10-3 1000 ANODE DARK CURRENT (nA) Figure 1: Typical Spectral Response Figure 5: Pulse Linearity per Channel 10 TPMHB0691EA TPMHB0692EA 10 PULSE WIDTH= 50 ns REPETITION= 1 kHz SUPPLY VOLTAGE= -800 V 0 Divider Ratio 2:2:2 :1:⋅⋅⋅⋅:1:1:1 -10 -20 10-2 10-1 0 DEVIATION (%) DEVIATION (%) PULSE WIDTH= 50 ns REPETITION= 1 kHz SUPPLY VOLTAGE= -800 V 100 Divider Ratio 2.4 : 2.4 : 2.4 : 1 : ⋅ ⋅ ⋅ ⋅ : 1 : 1.2 : 2.4 -10 -20 101 10-2 10-1 OUTPUT CURRENT (mA) OUTPUT CURRENT (mA) H8711 Figure 6: Anode Uniformity (Example) H8711-10 Figure 7: Anode Cross-talk (Example) 92 73 76 90 0.1 0.8 0.1 * 62 52 50 69 0.5 100 0.3 * 64 53 51 72 0.1 0.3 0.1 * 79 81 81 100 * * * * Supply Voltage: 800 V Light Source: Tungsten Lamp (uniform DC light) Full Illumination 100 Supply Voltage: 800 V Light Source: Tungsten Lamp (uniform DC light) Spot Illumination: 4 mm × 4 mm 101 MULTIANODE PHOTOMULTIPLIER TUBE ASSEMBLIES H8711, H8711-10 Figure 8: Dimensional Outline and Circuit Diagram (Unit: mm) POM CASE 9.3 14 7.62 2.54 1 MAX. 4.5 DY 45 ± 1 GND DY12 OUTPUT NOTE 1 0.65 2 Y PIN CONNECTION P1 P2 P3 P4 P5 P6 P7 P8 GND GND GND GND GND GND GND GND ANODE OUTPUTS (P1 to P8) TERMINAL PINS ( 0.46) ; BDL-108, SAMTEC H8711 NOTE 3 DY12 OUTPUT TERMINAL PINS ( 0.46) ; BBL-102, SAMTEC TERMINAL PINS (BDL-108, SAMTEC) P1 R1 to R3 : 360 kΩ R4 to R13 : 180 kΩ R14 : 1 MΩ R15 to R17 : 51 Ω R18 : 10 kΩ C1 to C4 : 0.01 µF K P2 P8 P9 F DY1 DY2 DY3 DY4 DY5 DY6 DY7 DY8 DY9 DY10 DY11 DY12 P15 P16 THROUGH HOLE (NO CONNECTION) -HV INPUT NOTE 2 -HV TERMINAL PINS ( 0.46) ; BBL-TYPE, SAMTEC ANODE OUTPUTS (P9 to P16) P9 P10 P11 P12 P13 P14 P15 P16 TERMINAL PINS ( 0.46) GND GND GND GND GND GND GND GND ; BDL-108, SAMTEC X P16 2.54 2.54 × 7=17.78 3.7 25.7 3 -HV GND 3.2 18.1 GUIDE MARK GND P8 P9 13 4.5 4-SCREWS (M2) 12.7 P1 2.54 15 30 ± 0.5 8.7 16 9.3 1 18.1 2 0.3 3 25.7 4 DIVIDER ASSEMBLY INSULATING TAPE 4- 0.3 GUIDE MARKS 0.3 5.08 8.7 ANODE1 OUTPUT GND ANODE2 OUTPUT GND ANODE8 OUTPUT GND TERMINAL PINS (BDL-108, SAMTEC) ANODE9 OUTPUT GND ANODE15 OUTPUT GND ANODE16 OUTPUT GND * Suitable sockets for all terminal pins are attached. NOTE 1 The suitable socket for anode output terminal pins is "SD-108-T-22 (SAMTEC U.S.A)" which is commercially available. NOTE 2 The suitable socket for hight voltage terminal pins is "SS-102-T-22 (SAMTEC U.S.A)" which is commercially available. NOTE 3 The suitable socket for DY12 output terminal pins is "ASP-24307-02 (SAMTEC U.S.A)" which is commercially available. C4 R14 R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R15 R11 R16 R12 R17 R13 C1 C2 C3 R18 TERMINAL PINS (BBL-102, SAMTEC) DY12 OUTPUT GND TERMINAL PINS (BBL-TYPE, SAMTEC) -HV INPUT GND *NOTE: DIVIDER RATIO=2:2:2:1:1...1:1:1 TPMHA0496EA H8711-10 TERMINAL PINS (BDL-108, SAMTEC) P1 R1 to R3, R13 : 360 kΩ R4 to R11 : 150 kΩ R12 : 180 kΩ R14 : 1 MΩ R15 to R17 : 51 Ω R18 : 10 kΩ C1 to C4 : 0.01 µF K F P2 P8 P9 DY1 DY2 DY3 DY4 DY5 DY6 DY7 DY8 DY9 DY10 DY11 DY12 P15 P16 ANODE1 OUTPUT GND ANODE2 OUTPUT GND ANODE8 OUTPUT GND TERMINAL PINS (BDL-108, SAMTEC) ANODE9 OUTPUT GND ANODE15 OUTPUT GND ANODE16 OUTPUT GND C4 R14 R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R15 R11 R16 R12 R17 R13 C1 C2 C3 R18 TERMINAL PINS (BBL-102, SAMTEC) DY12 OUTPUT GND TERMINAL PINS (BBL-TYPE, SAMTEC) -HV INPUT GND *NOTE: DIVIDER RATIO=2.4:2.4:2.4:1:1...1:1.2:2.4 TPMHA0497EA WARNING ~ High Voltage ~ The product is operated at high voltage potential. Further, the metal housing of the product is connected to the photocathode (potential) so that it becomes a high voltage potential when the product is operated at a negative high voltage (anode grounded). Accordingly, extreme safety care must be taken for the electrical shock hazard to the operator or the damage to the other instruments. * PATENT: USA Pat. No. 5410211 PATENTE PENDING: JAPAN 11, USA 1, EUROPE 2 WEB SITE http://www.hamamatsu.com HAMAMATSU PHOTONICS K.K., Electron Tube Center 314-5, Shimokanzo, Toyooka-village, Iwata-gun, Shizuoka-ken, 438-0193, Japan, Telephone: (81)539/62-5248, Fax: (81)539/62-2205 U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P. O. Box 6910, Bridgewater. N.J. 08807-0910, U.S.A., Telephone: (1)908-231-0960, Fax: (1)908-231-1218 E-mail: [email protected] Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49)8152-375-0, Fax: (49)8152-2658 E-mail: [email protected] France: Hamamatsu Photonics France S.A.R.L.: 8, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: (33)1 69 53 71 00, Fax: (33)1 69 53 71 10 E-mail: [email protected] United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road Welwyn Garden City Hertfordshire AL7 1BW, United Kingdom, Telephone: 44-(0)1707-294888, Fax: 44(0)1707-325777 E-mail: [email protected] North Europe: Hamamatsu Photonics Norden AB: Smidesvägen 12, SE-171-41 SOLNA, Sweden, Telephone: (46)8-509-031-00, Fax: (46)8-509-031-01 E-mail: [email protected] Italy: Hamamatsu Photonics Italia: S.R.L.: Strada della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39)02-935 81 733, Fax: (39)02-935 81 741 E-mail: [email protected] TPMH1278E02 APR. 2003 IP