Part Number: LUGY92M T-1(3mm) BI-COLOR INDICATOR LAMP www.SunLED.com Features z UNIFORM LIGHT OUTPUT. z LOW POWER CONSUMPTION. z 3 LEADS WITH ONE COMMON LEAD. z I.C. COMPATIBLE. z LONG LIFE - SOLID STATE RELIABILITY. z RoHS COMPLIANT. Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ± 0.25(0.01") unless otherwise noted. 3. Specifications are subject to change without notice. Absolute Maximum Ratings (TA=25°C) Operating Characteristics (TA=25°C) UG (GaP) UY (GaAsP /GaP) Unit UG (GaP) UY (GaAsP/ Unit GaP) Forward Voltage (Typ.) (IF=20mA) VF 2.2 2.1 V Reverse Voltage VR 5 5 V Forward Current IF 25 30 mA Forward Voltage (Max.) (IF=20mA) VF 2.5 2.5 V Forward Current (Peak) 1/10Duty Cycle 0.1ms Pulse Width iFS 140 140 mA Reverse Current (Max.) (VR=5V) IR 10 10 uA Power Dissipation PT 62.5 75 mW λP 565 590 nm Operating Temperature TA -40 ~ +85 Wavelength Of Peak Emission (Typ.) (IF=20mA) Tstg -40 ~ +85 Wavelength Of Dominant Emission (Typ.) (IF=20mA) λD 568 588 nm Spectral Line Full Width At Half-Maximum (Typ.) (IF=20mA) Δλ 30 35 nm Capacitance (Typ.) (VF=0V, f=1MHz) C 15 20 pF Storage Temperature Lead Solder Temperature [2mm Below Package Base] 260°C For 3 Seconds Lead Solder Temperature [5mm Below Package Base] 260°C For 5 Seconds Part Number LUGY92M Emitting Color Emitting Material Green GaP Yellow GaAsP/GaP Published Date : MAR 22, 2008 °C Luminous Intensity (IF=20mA) mcd Lens-color White Diffused Drawing No : SDSA3154 Wavelength nm λP min. typ. 10 29 565 7 14 590 V3 Checked : B.L.LIU Viewing Angle 2 θ 1/2 60° P.1/5 Part Number: LUGY92M T-1(3mm) BI-COLOR INDICATOR LAMP www.SunLED.com UG Published Date : MAR 22, 2008 Drawing No : SDSA3154 V3 Checked : B.L.LIU P.2/5 Part Number: LUGY92M T-1(3mm) BI-COLOR INDICATOR LAMP www.SunLED.com UY Published Date : MAR 22, 2008 Drawing No : SDSA3154 V3 Checked : B.L.LIU P.3/5 Part Number: LUGY92M T-1(3mm) BI-COLOR INDICATOR LAMP www.SunLED.com Remarks: If special sorting is required (e.g. binning based on forward voltage, luminous intensity / luminous flux or wavelength), the typical accuracy of the sorting process is as follows: 1. Wavelength: +/-1nm 2. Luminous Intensity / luminous flux: +/-15% 3. Forward Voltage: +/-0.1V Note: Accuracy may depend on the sorting parameters. Published Date : MAR 22, 2008 Drawing No : SDSA3154 V3 Checked : B.L.LIU P.4/5 Part Number: T-1(3mm) BI-COLOR INDICATOR LAMP www.SunLED.com PACKING & LABEL SPECIFICATIONS Published Date : MAR 22, 2008 LUGY92M Drawing No : SDSA3154 LUGY92M V3 Checked : B.L.LIU P.5/5