POWER LDO10C Series 50 Watts Data Sheet Total Power: Input Voltage: # of Outputs: 50 Watts 3 - 13.8 Vdc Single SPECIAL FEATURES 10 A output current rating Input voltage range: 3 - 13.8 Vdc Adjustable output voltage: 0.59 - 5.1 V Excellent transient response Power enable (5-pin model) Electrical Specifications Minimum airflow Input Small package Input voltage range Termination voltage capability Input current Minimum load Remote OFF 50 mA 5 mA Input current (max.) See Note 3 10 A @ lo max. Start-up time Power up Remote ON/OFF 3 ms 2 ms Output voltage See Note 5 0.59 - 5.1 V Output setpoint accuracy 0.1% trim resistors ±1.0% Line regulation Low line to high line ±0.2% Load regulation Full load to min. load ±0.5% RoHS compliant SAFETY UL, cUL 60950-1 TÜV Product Service (EN60950) CE 3 - 13.8 Vdc Output Min./max. load 0 A/10 A Overshoot At turn-on 0.5% max. Undershoot At turn-off 100 mV max. Ripple and noise 5 Hz to 20 MHz See Note 1 20 mV Vin = 5 V, Vout = 2.5 V Transient response See Note 1, 2 130 mV max. deviation 15 μs recovery to within regulation band Efficiency (high input) Vin = 5 V, Vo = 2.5 V, lo = 6 A 91% Switching frequency Fixed 620 kHz General Material flammability UL94V-0 Weight 1.899 g (0.067 oz.) MTBF 12 V @ 40 °C, 100% load Bellcore 332 >8,222,210 hours Coplanarity Surface mount models 150 μm LDO10C Series Data Sheet Environmental Specifications Thermal performance Operating ambient temperature -40 °C to +85 °C See Note 5 Non-operating ambient temperature -40 °C to +125 °C Protection Hiccup, non-latching Short-circuit Recommended System Capacitance Input See Note 6 0 μF Output See Note 7 0 μF Ordering Information Model Number (3,5) Regulation Output Power (Max.) Input Voltage Output Voltage Output Current (Min.) Output Current (Max.) Efficiency (Typical) Line Load LDO10C-005W05-VJ 50 W 3 - 13.8 Vdc 0.59 - 5.1 V 0A 10 A 94% ±0.2% ±0.5% LDO10C-005W05-HJ 50 W 3 - 13.8 Vdc 0.59 - 5.1 V 0A 10 A 94% ±0.2% ±0.5% LDO10C-005W05-SJ 50 W 3 - 13.8 Vdc 0.59 - 5.1 V 0A 10 A 94% ±0.2% ±0.5% Part Number System with Options Product Family LDO Product Family LDO = LDO Series Rated Output Current Performance 10 Rated Output Current 10 = 10 Amp Input Voltage Number of Pins Type of Output C 00 5W Performance C = Cost Optimized Input Voltage 00 = 3 - 13.8 V Type of Output 5 W = 5 Pins and Wide Output Output Voltage Adjustment of the LDO10C Series The ultra-wide output voltage trim range offers major advantages to users who select the LDO10C series. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be trimmed in a range of 0.59 - 5.1 Vdc. When the LDO10C converter leaves the factory, the output has been adjusted to the default voltage of 0.59 V. Output Voltage 05 Output Voltage 05 = 0.59 - 5.1 V Rem ote O N/O FF 2. di/dt = 10 A/μs, Vin = Nom, Tc = 25 °C, load change = 0.50 lo to full lo and full lo to 0.50. 3. External input fusing is recommended. 4. Additional part numbers may be available with different output voltages. 5. Airflow dependent, 100 LFM minimum required. 6. No capacitors needed for ripple current stability. 7. No capacitors needed for stability. 8. NOTICE: the input voltage must be greater than the programmed output voltage. The max duty cycle is 95%. These non-isolated dc-dc modules are buck converters. Custom Option V X Mounting Option V = Vertical H = Horizontal S = SMT Custom Option RoHS Compliance J RoHS Compliance J = Pb free (RoHS 6/6 compliant) V out 4 1 LD O10C Vni 2 Cni Notes: 1. Measured as per recommended system capacitance. See Application Note 186. Mounting Option 3 C out 5 Rm tri f( orm tri dow n) G ND Standard Application Drawing R L O A D LDO10C Series Data Sheet Mechanical Drawings Vertical Mount Dimensions in inches (mm). Tolerances (unless otherwise specified) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) Pin Assignments Pin No. Function 1 2 3 4 5 Enable Vin Common/RTN Vout Trim .410 .460 MAX .055 REF .062 REF .030 .650 .34 5 1 .131 .160±.010 .071 .050 .025 .001 SQ PINS TYP 4X .067 TYP Horizontal Mount Dimensions in inches (mm). Tolerances (unless otherwise specified) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) Pin Assignments Pin No. Function 1 2 3 4 5 6 Enable Vin Common/RTN Vout Trim Mech Pin .410 .545 MAX .545 MAX.460 MAX .410 .050 .050 .055 REF .410 6 .055 REF.055 REF .062 REF.062 REF .062 REF .030 .650 .580 .580 .650 .34 .131 5 .025±.001 .025±.001 SQ PIN TYP SQ PIN TYP 6 PLACES 6 PLACES 1.160±.010 .071 .035 .071 .035 .071 4X .067 4X .067 TYP TYP .050 4X .067 TYP .125 TYP.125 TYP .025 .001 SQ PINS TYP .120 TYP.120 TYP LDO10C Series Data Sheet Mechanical Drawings Mating Connectors Vertical Mount Dimensions in inches (mm). Tolerances (unless otherwise specified) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) Pin Assignments 0.52 (13.13) Pin No. Function 1 2 3 4 5 6 7 Enable Vin Common/RTN Vout Trim Mech Pin Mech Pin 6 0.410 (10.41) 0.062 (1.57) REF 7 0.650 (16.51) 7 6 LDO10C005W05- 5 1 0.040 (1.02) REF 5 1 0.035 (0.89) REF 0.055 (1.40) REF 0.025 (0.64) REF 0 (0.00) 0.050 (1.27) 0.071 (1.80) 0.138 (3.51) 0.205 (5.21) 0.272 (6.91) 0.339 (8.61) 0.360 (9.14) 0.125 (3.18) TYP WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832 Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 (0) 1384 842 211 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong +852 2176 3333 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2015 Artesyn Embedded Technologies, Inc. www.artesyn.com For more information: www.artesyn.com/power For support: [email protected] LDO10C Series 27Mar2015