Version: January 12, 2017 (CCR) Carbon Composition Resistors Token Electronics Industry Co., Ltd. Web: www.token.com.tw Email: [email protected] Taiwan: No.137, Sec. 1, Zhongxing Rd., Wugu District, New Taipei City, Taiwan, R.O.C. 24872 Tel: +886 2981 0109 Fax: +886 2988 7487 China: 12F, Zhong Xing Industry Bld., Chuang Ye Road, Nan Shan District, Shen Zhen City, Guang Dong, China 518054 Tel: +86 755 26055363; Fax: +86 755 26055365 Product Introduction High pulse withstanding carbon composition resistors handle big peaks and pulses. Features : Low inductance Solid rod carbon composition Power rating 1/4W and 2W Resistance range 1.8Ω ~ 22KΩ Resistance tolerance J(±5%), K(±10%) and M(±20%) High pulse withstanding and high energy capability Products with Pb-free Terminations and RoHS compliant Applications : Strobe Lighting High Power Lighting Medical defibrillators Welding, Automotive Inrush Current Limiting High Voltage Power Supplies Protection (e.g. Discharge Circuits, Surge Protection) The high pulse withstanding capability of the CCR series of carbon composition resistors from Token Electronics offers designers a compact solution for applications involving high voltages and high-energy pulses. Though, many resistor manufacturers claim to offer carbon composition replacements. However, these wire wound or thick film alternatives do not fully match the pulse performance and low inductance of carbon composition. Token's CCR series now offers the industry a carbon composition resistor made up of a solid rod of conductive composite material, the chemical composition of which is altered to produce different resistance values. The main advantage of carbon composition is their pulse handling capability. This is due to the fact that the entire rod conducts and so the thermal mass is far higher, which results in a higher energy capability. Due to the need for higher peak voltages, the CCR range is perfect for vehicle ignition system applications, medical monitoring equipment and as output resistors in defibrillators. The standard carbon composition CCR resistor offers a power rating of 1/4W, 1/2W, 1W and 2W at 25 ℃ and is made up of a solid rod of conductive composition material, which can be altered to produce different resistance values. With a typical resistance range of 1.8Ω ~ 22KΩ, resistance tolerance is J(±5%), K(±10%) and M(±20%). Resistors with 5%, 10% and 20% tolerance have four bands indicating value and tolerance in accordance with IEC62. Our custom solutions are designed to address your need for technical and economic success in a timely manner. Contact us with your specific needs. For more information, please link to Token official website "General Purpose Resistors". http://www.token.com.tw Taiwan Factory: +886 2 29810109 [email protected] China Factory: +86 755 26055363 Page: 1/5 Dimensions Dimensions (Unit: mm) (CCR) Type Power Rating L CCR 1/4W 6.3 CCR 1/2W 9.5 CCR 1W 15 CCR 2W 18 +1.0 -1.0 +0.5 -1.5 +1.5 -0.5 +0.5 -1.5 ΦD H Φd 2.3±0.3 27±2 0.60±0.02 3.5±0.3 27±2 0.70±0.02 6.0±0.3 28±2 0.80±0.02 8.0±0.3 27±2 1.00±0.02 Carbon Composition (CCR) Dimensions (Unit: mm) Ratings Specifications Ratings Specifications (CCR) Type Power Rating Resistance Range CCR 1/4W 2.2Ω ~ 12MΩ CCR 1/2W 2.2Ω ~ 22MΩ CCR 1W 2.2Ω ~ 22KΩ CCR 2W 1.8Ω ~ 10KΩ Tolerance E12,E24 J(±5%) K±10% M±20% Max Working voltage Max overload Rated Ambient Voltage Temp. Operating Temp. Range 250V 400V +70℃ -55℃ ~ +125℃ 350V 700V +70℃ -55℃ ~ +125℃ 500V 1000V +70℃ -55℃ ~ +125℃ 500V 1000V +70℃ -55℃ ~ +125℃ Rated Voltage = √𝐏𝐨𝐰𝐞𝐫 𝐑𝐚𝐭𝐢𝐧𝐠 ∗ 𝐑𝐞𝐬𝐢𝐬𝐭𝐚𝐧𝐜𝐞 𝐕𝐚𝐥𝐮𝐞 or Max. Working voltage, whichever is lower. http://www.token.com.tw Taiwan Factory: +886 2 29810109 [email protected] China Factory: +86 755 26055363 Page: 2/5 Derating Curve Derating Curve (CCR) (CCR) Derating Curve http://www.token.com.tw Taiwan Factory: +886 2 29810109 [email protected] China Factory: +86 755 26055363 Page: 3/5 Performance Performance (CCR) Description Performance Requirements Test Method Maximum Resistance Value Resistance Range Change % -40~+20℃ +20~+100℃ Resistance Temperature Coefficient <1KΩ 1.1KΩ ~10KΩ 11KΩ ~100KΩ 11KΩ ~1MΩ 1.1MΩ ~10MΩ >11MΩ Short-time Overload Δ R≤±2.5% Rate Voltage*2.5 or maximum overload voltage (the lower)5sec. With Standing Voltage No flashover or breakdown 2times maximum working voltage 1 minute Terminal Strength ±6.5% ±10% ±13% ±15% ±20% ±25% ±5.0% ±6.0% ±7.5% ±10% ±15% ±20% Test Temperature +20℃ /-40℃ /+20℃ /+100℃ /+20℃ Pulled Winded ΔR≤±2% No visible damage Twisted Resistance to vibration Load 10N 10s Load 10N 4*90° 3*360° in opposite direction No visible damage 10~50Hz 3 direction 2 hours each 350℃ 4mm from the body,3 seconds Solder-heat Resistance ΔR≤±5% Marks legible, no visible damage Solderability Temperature Cycle At least 95% if the dipping surface must be covered 235℃ 2mm from the body,2 seconds by new solder, no flaws gathered. ΔR≤±2% -40℃(30min.)/85℃(30min.)5 cycles No visible damage Humidity ΔR≤±10% No visible damage 40℃ 95% RH 240 hours Load Life ΔR≤±10% No visible damage, marks legible Rated voltage or maximum working voltage, 1.5 hours on, 0.5 hours off, 40℃ 1000 hours Order Codes Order Codes (CCR) CCR 1/2W 120R K P Part Number Rated Power (W) Resistance Value (Ω) Resistance Tolerance (%) Package CCR 2R2 2.2Ω 120R 120Ω J ±5% 1M2 1.2MΩ K ±10% 22M 22MΩ M ±20% P http://www.token.com.tw Taiwan Factory: +886 2 29810109 [email protected] China Factory: +86 755 26055363 Bulk Page: 4/5 General Information General Purpose Resistors with Customized Service Token Electronics is expanding business to include a broad range of General Purpose Resistor products designed for high volume applications. This expanded range of commercial resistor presents a more comprehensive product offering for Customer Experience Management (CEM) and other high volume customers that require quality products at competitive pricing. Backed by the same customer service, technical support and quality assurance that Token has always provided, these new commercial products enable you the opportunity to source a wider range of resistors from a trusted supplier. General Use When an ambient temperature exceeds a rated ambient temperature, resistor shall be applied on the derating curve by derating the load power. General purpose resistor under overloads is not combustion resistant and is likely to emit, flame, gas, smoke, red heat, etc. Flame retardant resistor generally emits smoke and red heat in a certain power and over but do not emit fire or flame. When resistors are shielded or coated with resin etc., stress from the storage heat and the resins are applied. So, performance and reliability should be checked well before use. When a voltage higher than rated is applied in a short time (single pulse, repeated pulses, surge, etc.), it does not necessarily ensure safety that an effective wattage is not higher than a rated wattage. Then consult with us with your specified pulse wave shape. Resistors shall be used in a condition causing no dew condensation. Keep temperature from rising by choosing resistor with a higher rated capacity; do not use a component having the exact load value required. For considerations of safety in extended period applications, the rating should be more than four times higher than the actual wattage involved, but never use resistors at less than 25% of its rated power. In applications where resistors are subject to intermittent current surges and spikes, be sure in advance that the components selected are capable of withstanding brief durations of increased load. Do not exceed the recommended rated load. Resistor must use within the rated voltage range to prevent the shortening of service life and/or failure of the wound resistance elements. Minimum load: Resistor must be utilized at 1/10 or more of the rated voltage to prevent poor conductance due to oxidation build-up. For basic particulars for cautions, refer to EIAJ Technical Report RCR-2121 "Guidance for care note on fixed-resistors". http://www.token.com.tw Taiwan Factory: +886 2 29810109 [email protected] China Factory: +86 755 26055363 Page: 5/5