PD - 94403A
IRL3716
IRL3716S
IRL3716L
SMPS MOSFET
Applications
l High Frequency Isolated DC-DC
Converters with Synchronous Rectification
for Telecom and Industrial Use
l High Frequency Buck Converters for
Computer Processor Power
l Active Oring
Benefits
l Ultra-Low Gate Impedance
l Very Low RDS(on) at 4.5V VGS
l Fully Characterized Avalanche Voltage
and Current
HEXFET® Power MOSFET
VDSS
RDS(on) max
20V
4.0mΩ
TO-220AB
IRL3716
D2Pak
IRL3716S
ID
180A
TO-262
IRL3716L
Absolute Maximum Ratings
Symbol
VDS
VGS
ID @ TC
ID @ TC
I DM
PD @TC
PD @TC
= 25°C
= 100°C
= 25°C
= 100°C
TJ , TSTG
Parameter
Drain-Source Voltage
Gate-to-Source Voltage
Continuous Drain Current, VGS @ 10V
Continuous Drain Current, VGS @ 10V
Pulsed Drain Current
Maximum Power Dissipation
Maximum Power Dissipation
Linear Derating Factor
Junction and Storage Temperature Range
Max.
Units
20
± 20
180
130
720
210
100
1.4
-55 to + 175
V
V
A
W
W
W/°C
°C
Thermal Resistance
RθJC
RθCS
RθJA
RθJA
Parameter
Typ.
Max.
Junction-to-Case
Case-to-Sink, Flat, Greased Surface
Junction-to-Ambient
Junction-to-Ambient (PCB mount)
–––
0.50
–––
–––
0.72
–––
62
40
Units
°C/W
Notes through are on page 11
www.irf.com
1
10/8/04
IRL3716/3716S/3716L
Static @ TJ = 25°C (unless otherwise specified)
Parameter
Drain-to-Source Breakdown Voltage
∆V(BR)DSS/∆TJ Breakdown Voltage Temp. Coefficient
V(BR)DSS
RDS(on)
VGS(th)
IDSS
IGSS
Min.
20
–––
–––
Static Drain-to-Source On-Resistance
–––
Gate Threshold Voltage
1.0
–––
Drain-to-Source Leakage Current
–––
Gate-to-Source Forward Leakage
–––
Gate-to-Source Reverse Leakage
–––
Typ. Max. Units
Conditions
–––
––– V
VGS = 0V, ID = 250µA
0.021 ––– V/°C Reference to 25°C, ID = 1mA
3.0
4.0
VGS = 10V, ID = 90A
mΩ
4.0
4.8
VGS = 4.5V, ID = 72A
–––
3.0
V
VDS = VGS, ID = 250µA
–––
20
VDS = 16V, VGS = 0V
µA
–––
250
VDS = 16V, VGS = 0V, TJ = 125°C
–––
200
VGS = 16V
nA
––– -200
VGS = -16V
Dynamic @ TJ = 25°C (unless otherwise specified)
Symbol
gfs
Qg
Qgs
Qgd
Qoss
Parameter
Forward Transconductance
Total Gate Charge
Gate-to-Source Charge
Gate-to-Drain ("Miller") Charge
Output Gate Charge
Rg
Gate Resistance
td(on)
tr
td(off)
tf
Ciss
Coss
Crss
Turn-On Delay Time
Rise Time
Turn-Off Delay Time
Fall Time
Input Capacitance
Output Capacitance
Reverse Transfer Capacitance
Min. Typ. Max. Units
Conditions
100 ––– –––
S
VDS = 10V, ID = 72A
–––
53
79
ID = 72A
–––
17
26
nC VDS = 16V
–––
24
35
VGS = 4.5V
–––
50
75
VGS = 0V, V DS = 10V
Ω
1.5
–––
–––
–––
–––
–––
–––
–––
18
140
38
36
5090
3440
560
–––
–––
–––
–––
–––
–––
–––
ns
pF
VDD = 10V
ID = 72A
RG = 3.9Ω
VGS = 4.5V
VGS = 0V
VDS = 10V
ƒ = 1.0MHz
Avalanche Characteristics
Symbol
EAS
IAR
Parameter
Single Pulse Avalanche Energy
Avalanche Current
Typ.
Max.
Units
–––
–––
640
72
mJ
A
Diode Characteristics
Symbol
IS
I SM
Parameter
Continuous Source Current
(Body Diode)
Pulsed Source Current
(Body Diode)
VSD
Diode Forward Voltage
trr
Q rr
trr
Q rr
Reverse
Reverse
Reverse
Reverse
2
Recovery
Recovery
Recovery
Recovery
Time
Charge
Time
Charge
Min. Typ. Max. Units
–––
––– 180
–––
–––
720
–––
–––
–––
–––
–––
–––
0.93
0.80
180
87
190
85
1.3
–––
280
130
280
130
A
V
ns
nC
ns
nC
Conditions
D
MOSFET symbol
showing the
G
integral reverse
S
p-n junction diode.
TJ = 25°C, IS = 72A, VGS = 0V
TJ = 125°C, IS = 72A, VGS = 0V
TJ = 25°C, IF = 72A, VR=20V
di/dt = 100A/µs
TJ = 125°C, IF = 72A, VR=20V
di/dt = 100A/µs
www.irf.com
IRL3716/3716S/3716L
10000
10000
VGS
10V
4.5V
3.7V
3.5V
3.3V
3.0V
2.7V
BOTTOM 2.5V
VGS
10V
4.5V
3.7V
3.5V
3.3V
3.0V
2.7V
BOTTOM 2.5V
1000
TOP
ID, Drain-to-Source Current (A)
ID, Drain-to-Source Current (A)
TOP
100
2.5V
10
1000
100
2.5V
10
20µs PULSE WIDTH
Tj = 175°C
20µs PULSE WIDTH
Tj = 25°C
1
1
0.1
1
10
100
0.1
1
VDS, Drain-to-Source Voltage (V)
10
100
VDS, Drain-to-Source Voltage (V)
Fig 1. Typical Output Characteristics
Fig 2. Typical Output Characteristics
1000.00
2.0
I D = 180A
ID, Drain-to-Source Current (Α)
T J = 25°C
100.00
VDS = 15V
20µs PULSE WIDTH
10.00
2.0
3.0
4.0
5.0
6.0
7.0
VGS, Gate-to-Source Voltage (V)
Fig 3. Typical Transfer Characteristics
www.irf.com
8.0
1.5
(Normalized)
RDS(on) , Drain-to-Source On Resistance
T J = 175°C
1.0
0.5
V GS = 10V
0.0
-60
-40
-20
0
20
40
60
80
TJ , Junction Temperature
100 120 140 160 180
( ° C)
Fig 4. Normalized On-Resistance
Vs. Temperature
3
IRL3716/3716S/3716L
100000
16
VGS = 0V,
f = 1 MHZ
Ciss = Cgs + Cgd , Cds SHORTED
Crss = Cgd
VDS = 16V
12
VGS , Gate-to-Source Voltage (V)
C, Capacitance(pF)
Coss = Cds + Cgd
10000
Ciss
Coss
1000
Crss
100
8
4
0
1
10
0
100
60
90
120
150
Fig 6. Typical Gate Charge Vs.
Gate-to-Source Voltage
Fig 5. Typical Capacitance Vs.
Drain-to-Source Voltage
10000
ID , Drain-to-Source Current (A)
1000
TJ = 175 ° C
100
I SD, Reverse Drain Current (A)
30
QG, Total Gate Charge (nC)
VDS , Drain-to-Source Voltage (V)
TJ = 25 ° C
10
V GS= 0 V
0.8
1.4
100µsec
100
1
0.2
OPERATION IN THIS AREA
LIMITED BY R DS(on)
1000
2.0
V SD,Source-to-Drain Voltage (V)
Fig 7. Typical Source-Drain Diode
Forward Voltage
1msec
10
2.6
10msec
Tc = 25°C
Tj = 175°C
Single Pulse
1
0.1
4
ID = 72A
1
10
100
VDS , Drain-toSource Voltage (V)
Fig 8. Maximum Safe Operating Area
www.irf.com
IRL3716/3716S/3716L
180
RD
V DS
LIMITED BY PACKAGE
VGS
150
D.U.T.
RG
+
-VDD
I D , Drain Current (A)
120
4.5V
Pulse Width ≤ 1 µs
Duty Factor ≤ 0.1 %
90
Fig 10a. Switching Time Test Circuit
60
VDS
30
90%
0
25
50
75
100
125
TC , Case Temperature
150
175
( ° C)
10%
VGS
Fig 9. Maximum Drain Current Vs.
Case Temperature
td(on)
tr
t d(off)
tf
Fig 10b. Switching Time Waveforms
Thermal Response
(Z thJC )
10
1
D = 0.50
0.20
0.1
P DM
0.10
t1
0.05
0.02
0.01
t2
SINGLE PULSE
(THERMAL RESPONSE)
Notes:
1. Duty factor D =
2. Peak T
0.01
0.00001
0.0001
0.001
0.01
t1/ t 2
J = P DM x Z thJC
+TC
0.1
1
t 1, Rectangular Pulse Duration (sec)
Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case
www.irf.com
5
IRL3716/3716S/3716L
1650
15V
D.U.T
RG
+
V
- DD
IAS
20V
tp
A
0.01Ω
Fig 12a. Unclamped Inductive Test Circuit
V(BR)DSS
tp
EAS , Single Pulse Avalanche Energy (mJ)
VDS
1320
DRIVER
L
TOP
ID
29A
BOTTOM
51A
72A
990
660
330
0
25
50
75
100
Starting Tj, Junction Temperature
125
150
175
( ° C)
Fig 12c. Maximum Avalanche Energy
Vs. Drain Current
I AS
Fig 12b. Unclamped Inductive Waveforms
Current Regulator
Same Type as D.U.T.
QG
4.5 V
50KΩ
12V
.2µF
.3µF
QGS
QGD
D.U.T.
VG
+
V
- DS
VGS
3mA
Charge
Fig 13a. Basic Gate Charge Waveform
6
IG
ID
Current Sampling Resistors
Fig 13b. Gate Charge Test Circuit
www.irf.com
IRL3716/3716S/3716L
Peak Diode Recovery dv/dt Test Circuit
Circuit Layout Considerations
• Low Stray Inductance
• Ground Plane
• Low Leakage Inductance
Current Transformer
+
D.U.T
+
-
-
+
RG
•
•
•
•
dv/dt controlled by RG
Driver same type as D.U.T.
ISD controlled by Duty Factor "D"
D.U.T. - Device Under Test
Driver Gate Drive
P.W.
Period
D=
+
-
VDD
P.W.
Period
VGS=10V
*
D.U.T. ISD Waveform
Reverse
Recovery
Current
Body Diode Forward
Current
di/dt
D.U.T. VDS Waveform
Diode Recovery
dv/dt
Re-Applied
Voltage
Body Diode
VDD
Forward Drop
Inductor Curent
Ripple ≤ 5%
ISD
* VGS = 5V for Logic Level Devices
Fig 14. For N-Channel HEXFET® Power MOSFETs
www.irf.com
7
IRL3716/3716S/3716L
TO-220AB Package Outline
Dimensions are shown in millimeters (inches)
2.87 (.113)
2.62 (.103)
10.54 (.415)
10.29 (.405)
-B-
3.78 (.149)
3.54 (.139)
4.69 (.185)
4.20 (.165)
-A-
1.32 (.052)
1.22 (.048)
6.47 (.255)
6.10 (.240)
4
15.24 (.600)
14.84 (.584)
LEAD ASSIGNMENTS
1.15 (.045)
MIN
1
2
3
1234-
14.09 (.555)
13.47 (.530)
1.40 (.055)
1.15 (.045)
2 - DRAIN
GATE
3 - SOURCE
DRAIN
SOURCE
4 - DRAIN
DRAIN
IGBTs, CoPACK
1- GATE
2- COLLECTOR
3- EMITTER
4- COLLECTOR
4.06 (.160)
3.55 (.140)
3X
3X
LEAD ASSIGNMENTS
HEXFET
1 - GATE
0.93 (.037)
0.69 (.027)
0.36 (.014)
3X
M
B A M
0.55 (.022)
0.46 (.018)
2.92 (.115)
2.64 (.104)
2.54 (.100)
2X
NOTES:
1 DIMENSIONING & TOLERANCING PER ANSI Y14.5M, 1982.
2 CONTROLLING DIMENSION : INCH
3 OUTLINE CONFORMS TO JEDEC OUTLINE TO-220AB.
4 HEATSINK & LEAD MEASUREMENTS DO NOT INCLUDE BURRS.
TO-220AB Part Marking Information
E XAMPLE : T HIS IS AN IR F 1010
LOT CODE 1789
AS S E MB LE D ON WW 19, 1997
IN T HE AS S E MB LY LINE "C"
Note: "P" in assembly line
position indicates "Lead-Free"
INT E R NAT IONAL
R E CT IF IE R
LOGO
AS S E MB LY
LOT CODE
8
PAR T NU MB E R
DAT E CODE
YE AR 7 = 1997
WE E K 19
L INE C
www.irf.com
IRL3716/3716S/3716L
D2Pak Package Outline
Dimensions are shown in millimeters (inches)
D2Pak Part Marking Information
T HIS IS AN IRF 530S WIT H
L OT CODE 8024
AS S E MB L ED ON WW 02, 2000
IN T HE AS S E MBL Y L INE "L "
INT E RNAT IONAL
R E CT IFIER
L OGO
Note: "P" in as s embly line
pos ition indicates "L ead-F ree"
PAR T NUMBE R
F 530S
AS S E MBL Y
L OT CODE
DAT E CODE
YE AR 0 = 2000
WEE K 02
L INE L
OR
INT E RNAT IONAL
RE CT IF IE R
LOGO
AS S E MBL Y
L OT CODE
www.irf.com
PART NUMB E R
F 530S
DAT E CODE
P = DE S IGNAT E S L E AD-F RE E
PRODUCT (OPT IONAL )
YE AR 0 = 2000
WE E K 02
A = AS S E MB LY S IT E CODE
9
IRL3716/3716S/3716L
TO-262 Package Outline
Dimensions are shown in millimeters (inches)
TO-262 Part Marking InformaEXAMPLE: T HIS IS AN IRL3103L
LOT CODE 1789
AS S E MB LED ON WW 19, 1997
IN T HE AS S E MBL Y L INE "C"
Note: "P" in as sembly line
pos ition indicates "L ead-Free"
INT E RNAT IONAL
RECT IFIER
L OGO
AS S EMBL Y
L OT CODE
PART NUMBER
DAT E CODE
YEAR 7 = 1997
WEE K 19
L INE C
OR
INT ERNAT IONAL
RECT IF IE R
LOGO
AS S EMB LY
L OT CODE
10
PART NUMBER
DAT E CODE
P = DES IGNAT E S LE AD-F REE
PRODUCT (OPT IONAL)
YEAR 7 = 1997
WEE K 19
A = AS S E MB LY S IT E CODE
www.irf.com
IRL3716/3716S/3716L
D2Pak Tape & Reel Information
Dimensions are shown in millimeters (inches)
TRR
1.60 (.063)
1.50 (.059)
1.60 (.063)
1.50 (.059)
4.10 (.161)
3.90 (.153)
FEED DIRECTION 1.85 (.073)
11.60 (.457)
11.40 (.449)
1.65 (.065)
0.368 (.0145)
0.342 (.0135)
15.42 (.609)
15.22 (.601)
24.30 (.957)
23.90 (.941)
TRL
1.75 (.069)
1.25 (.049)
10.90 (.429)
10.70 (.421)
4.72 (.136)
4.52 (.178)
16.10 (.634)
15.90 (.626)
FEED DIRECTION
13.50 (.532)
12.80 (.504)
27.40 (1.079)
23.90 (.941)
4
330.00
(14.173)
MAX.
Notes:
60.00 (2.362)
MIN.
NOTES :
1. COMFORMS TO EIA-418.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION MEASURED @ HUB.
4. INCLUDES FLANGE DISTORTION @ OUTER EDGE.
Repetitive rating; pulse width limited by
max. junction temperature.
26.40 (1.039)
24.40 (.961)
3
30.40 (1.197)
MAX.
4
Pulse width ≤ 400µs; duty cycle ≤ 2%.
This is only applied to TO-220AB package
Starting TJ = 25°C, L = 0.25mH
RG = 25Ω, I AS = 72A.
This is applied to D2Pak, when mounted on 1" square PCB ( FR-4 or G-10 Material ).
For recommended footprint and soldering techniques refer to application note #AN-994.
Calculated continuous current based on maximum allowable
junction temperature. Package limitation current is 75A.
Rθ is measured at TJ approximately 90°C
Data and specifications subject to change without notice.
This product has been designed and qualified for the Industrial market.
Qualification Standards can be found on IR’s Web site.
IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105
TAC Fax: (310) 252-7903
Visit us at www.irf.com for sales contact information.10/04
www.irf.com
11