ON NE5532AD8 Internally compensated dual low noise operational amplifier Datasheet

NE5532, SA5532, SE5532,
NE5532A, SE5532A
Internally Compensated
Dual Low Noise
Operational Amplifier
The 5532 is a dual high-performance low noise operational
amplifier. Compared to most of the standard operational amplifiers,
such as the 1458, it shows better noise performance, improved output
drive capability and considerably higher small-signal and power
bandwidths.
This makes the device especially suitable for application in
high-quality and professional audio equipment, instrumentation and
control circuits, and telephone channel amplifiers. The op amp is
internally compensated for gains equal to one. If very low noise is of
prime importance, it is recommended that the 5532A version be used
because it has guaranteed noise voltage specifications.
Features
•
•
•
•
•
•
•
•
•
•
http://onsemi.com
SOIC−8
D SUFFIX
CASE 751
8
1
PDIP−8
N SUFFIX
CASE 626
8
1
SOIC−16 WB
D SUFFIX
CASE 751G
16
Small-Signal Bandwidth: 10 MHz
Output Drive Capability: 600 W, 10 VRMS
1
Input Noise Voltage: 5.0 nVń ǸHz (Typical)
PIN CONNECTIONS
DC Voltage Gain: 50000
AC Voltage Gain: 2200 at 10 kHz
Power Bandwidth: 140 kHz
Slew Rate: 9.0 V/ms
Large Supply Voltage Range: "3.0 to "20 V
Compensated for Unity Gain
Pb−Free Packages are Available
N, D8 Packages
8 V+
OUTA
1
−INA
2
+INA
3
6 −INB
V-
4
5 +INB
A
B
7 OUTB
Top View
D Package*
−INA
1
16
NC
+INA
2
15
NC
NC
3
14
NC
V−
4
13
OUTA
NC
5
12
V+
NC
6
11
OUTB
+INB
7
10
NC
−INB
8
9
NC
Top View
*SOL and non-standard pinout.
DEVICE MARKING INFORMATION
See general marking information in the device marking
section on page 6 of this data sheet.
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 7 of this data sheet.
© Semiconductor Components Industries, LLC, 2006
March, 2006 − Rev. 1
1
Publication Order Number:
NE5532/D
NE5532, SA5532, SE5532, NE5532A, SE5532A
+
_
Figure 1. Equivalent Schematic (Each Amplifier)
MAXIMUM RATINGS
Symbol
Value
Unit
Supply Voltage
Rating
VS
"22
V
Input Voltage
VIN
"VSUPPLY
V
Differential Input Voltage (Note 1)
VDIFF
"0.5
V
Operating Temperature Range
NE5532/A
SA5532
SE5532/A
Tamb
Storage Temperature
Tstg
−65 to +150
°C
Junction Temperature
Tj
150
°C
Maximum Power Dissipation, Tamb = 25°C (Still-Air)
8 D8 Package
8 N Package
16 D Packagee
PD
Thermal Resistance, Junction−to−Ambient
8 D8 Package
8 N Package
16 D Packagee
RqJA
Lead Soldering Temperature (10 sec max)
Tsld
0 to 70
−40 to +85
−55 to +125
780
1200
1200
182
130
140
230
°C
mW
°C/W
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. Diodes protect the inputs against overvoltage. Therefore, unless current-limiting resistors are used, large currents will flow if the differential input
voltage exceeds 0.6 V. Maximum current should be limited to "10 mA.
http://onsemi.com
2
NE5532, SA5532, SE5532, NE5532A, SE5532A
DC ELECTRICAL CHARACTERISTICS (Tamb = 25°C; VS = "15 V, unless otherwise noted.) (Notes 2, 3 and 4)
SE5532/A
NE5532/A, SA5532
Symbol
Test Conditions
Min
Typ
Max
Min
Typ
Max
Unit
VOS
−
−
0.5
2.0
−
0.5
4.0
mV
−
Overtemperature
−
−
3.0
−
−
5.0
mV
DVOS/DT
−
−
5.0
−
−
5.0
−
mV/°C
IOS
−
−
−
100
−
10
150
nA
−
Overtemperature
−
−
200
−
−
200
nA
DIOS/DT
−
−
200
−
−
200
−
pA/°C
IB
−
−
200
400
−
200
800
nA
−
Overtemperature
−
−
700
−
−
1000
nA
DIB/DT
−
−
5.0
−
−
5.0
−
nA/°C
ICC
−
−
8.0
10.5
−
8.0
16
mA
−
Overtemperature
−
−
13
−
−
−
VCM
−
"12
"13
−
"12
"13
−
V
Common-Mode Rejection Ratio
CMRR
−
80
100
−
70
100
−
dB
Power Supply Rejection Ratio
PSRR
−
−
10
50
−
10
100
mV/V
Large-Signal Voltage Gain
AVOL
RL w 2.0 kW; VO = "10 V
50
100
−
25
100
−
V/mV
Overtemperature
25
−
−
15
−
−
RL w 600 W; VO = "10 V
40
50
−
15
50
−
Overtemperature
20
−
−
10
−
−
RL w 600 W
"12
"13
−
"12
"13
−
Overtemperature
"10
"12
−
"10
"12
−
RL w 600 W; VS = "18 V
"15
"16
−
"15
"16
−
Overtemperature
"12
"14
−
"12
"14
−
RL w 2.0 kW
"13
"13.5
−
"13
"13.5
−
Overtemperature
"12
"12.5
−
"10
"12.5
−
Characteristic
Offset Voltage
Offset Current
Input Current
Supply Current
Common-Mode Input Range
Output Swing
VOUT
V
Input Resistance
RIN
−
30
300
−
30
300
−
kW
Output Short Circuit Current
ISC
−
10
38
60
10
38
60
mA
2. Diodes protect the inputs against overvoltage. Therefore, unless current-limiting resistors are used, large currents will flow if the differential input
voltage exceeds 0.6 V. Maximum current should be limited to "10 mA.
3. For operation at elevated temperature, derate packages based on the package thermal resistance.
4. Output may be shorted to ground at VS = "15 V, Tamb = 25°C. Temperature and/or supply voltages must be limited to ensure dissipation rating
is not exceeded.
http://onsemi.com
3
NE5532, SA5532, SE5532, NE5532A, SE5532A
AC ELECTRICAL CHARACTERISTICS (Tamb = 25°C; VS = "15 V, unless otherwise noted.)
NE/SE5532/A, SA5532
Characteristic
Output Resistance
Overshoot
Symbol
Test Conditions
Min
Typ
Max
Unit
ROUT
AV = 30 dB Closed-loop
f = 10 kHz, RL = 600 W
−
0.3
−
W
−
Voltage-Follower
%
VIN = 100 mVP-P
−
10
−
CL = 100 pF; RL = 600 W
Gain
Gain Bandwidth Product
Slew Rate
Power Bandwidth
AV
f = 10 kHz
−
2.2
−
V/mV
GBW
CL = 100 pF; RL = 600 W
−
10
−
MHz
SR
−
−
9.0
−
V/ms
−
VOUT = "10 V
−
140
−
kHz
VOUT = "14 V;
RL = 600 W
−
100
−
VCC = "18 V
ELECTRICAL CHARACTERISTICS (Tamb = 25°C; VS = "15 V, unless otherwise noted.)
NE/SE5532
Characteristic
Input Noise Voltage
Input Noise Current
Channel Separation
NE/SA/SE5532A
Symbol
Test Conditions
Min
VNOISE
fO = 30 Hz
−
8.0
−
−
8.0
12
fO = 1.0 kHz
−
5.0
−
−
5.0
6.0
fO = 30 Hz
−
2.7
−
−
2.7
−
fO = 1.0 kHz
−
0.7
−
−
0.7
−
f = 1.0 kHz; RS = 5.0 kW
−
110
−
−
110
−
INOISE
−
http://onsemi.com
4
Typ
Max
Min
Typ
Max
Unit
nV/√Hz
pA/√Hz
dB
NE5532, SA5532, SE5532, NE5532A, SE5532A
TYPICAL PERFORMANCE CHARACTERISTICS
60
120
TYPICAL VALUES
GAIN (dB)
GAIN (dB)
40
30
RF = 9 kW; RE = 1 kW
20
10
102
103
104
105
106
107
(V)
Vo(p-p)
20
RF = 1 kW; RE = ∞
0
0
VS = "15 V
TYPICAL VALUES
RF = 10 kW; RE = 100 W
40
80
-40
40
TYPICAL VALUES
-20
103
104
10
105
106
107
0
102
108
103
104
f (Hz)
f (Hz)
Figure 2. Open-Loop Frequency
Response
Figure 3. Closed-Loop Frequency
Response
80
106
107
Figure 4. Large−Signal Frequency
Response
30
1,4
VS = "15 V
TYPICAL VALUES
VS = "15 V
60
105
f (Hz)
1,2
20
IO
40
(mA)
II
(mA)
TYP
0,8
VIN (V)
10
20
0
-55
0,4
0
0
-25
0
25
50
75
100 +125
-55
-25
0
Tamb (oC)
25
75
100 +125
0
10
Figure 6. Input Bias Current
6
TYP
4
Figure 7. Input Common−Mode
Voltage Range
10−2
IO = 0
10
TYP
IP
IN
(nVń ǸHz)
1
2
10−1
10−2
0
0
10
20
10
102
103
104
Vp; −VN (V)
f (Hz)
Figure 8. Supply Current
Figure 9. Input Noise Voltage
Density
http://onsemi.com
5
20
Vp; −VN (V)
Tamb (oC)
Figure 5. Output Short−Circuit
Current
(mA)
50
NE5532, SA5532, SE5532, NE5532A, SE5532A
+
V+
5532 (1/2)
RS
25 W
−
5532
RF
VOUT
−
+
VIN
1 kW
VI
RE
100 pF
100 pF
800 W
600 W
V−
Closed-Loop Frequency Response
Voltage-Follower
Figure 10. Test Circuits
MARKING DIAGRAMS
8
1
8
N5532
ALYWA
G
1
8
N5532
ALYW
G
SOIC−8
D SUFFIX
CASE 751
1
NE5532AN
AWL
YYWWG
S5532
ALYWA
G
NE5532N
AWL
YYWWG
SA5532N
AWL
YYWWG
PDIP−8
N SUFFIX
CASE 626
16
NE5532D
AWLYYWWG
1
SOIC−16 WB
D SUFFIX
CASE 751G
A
WL, L
YY, Y
WW, W
G or G
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Packagee
http://onsemi.com
6
SE5532N
AWL
YYWWG
NE5532, SA5532, SE5532, NE5532A, SE5532A
ORDERING INFORMATION
Description
Temperature Range
Shipping†
NE5532AD8
8−Pin Plastic Small Outline (SO−8) Packagee
0 to 70°C
98 Units / Rail
NE5532AD8G
8−Pin Plastic Small Outline (SO−8) Package
(Pb−Free)
0 to 70°C
98 Units / Rail
NE5532AD8R2
8−Pin Plastic Small Outline (SO−8) Packagee
0 to 70°C
2500 / Tape & Reel
NE5532AD8R2G
8−Pin Plastic Small Outline (SO−8) Package
(Pb−Free)
0 to 70°C
2500 / Tape & Reel
NE5532AN
8−Pin Plastic Dual In−Line Package (PDIP−8)
0 to 70°C
50 Units / Rail
NE5532ANG
8−Pin Plastic Dual In−Line Package (PDIP−8)
(Pb−Free)
0 to 70°C
50 Units / Rail
NE5532D
16−Pin Plastic Small Outline (SO−16 WB) Package
0 to 70°C
47 Units / Rail
NE5532DG
16−Pin Plastic Small Outline (SO−16 WB) Package
(Pb−Free)
0 to 70°C
47 Units / Rail
NE5532DR2
16−Pin Plastic Small Outline (SO−16 WB) Package
0 to 70°C
1000 Tape & Reel
NE5532DR2G
16−Pin Plastic Small Outline (SO−16 WB) Package
(Pb−Free)
0 to 70°C
1000 Tape & Reel
NE5532D8
8−Pin Plastic Small Outline (SO−8) Packagee
0 to 70°C
98 Units / Rail
NE5532D8G
8−Pin Plastic Small Outline (SO−8) Package
(Pb−Free)
0 to 70°C
98 Units / Rail
NE5532D8R2
8−Pin Plastic Small Outline (SO−8) Packagee
0 to 70°C
2500 / Tape & Reel
NE5532D8R2G
8−Pin Plastic Small Outline (SO−8) Package
(Pb−Free)
0 to 70°C
2500 / Tape & Reel
NE5532N
8−Pin Plastic Dual In−Line Package (PDIP−8)
0 to 70°C
50 Units / Rail
NE5532NG
8−Pin Plastic Dual In−Line Package (PDIP−8)
(Pb−Free)
0 to 70°C
50 Units / Rail
SA5532N
8−Pin Plastic Dual In−Line Package (PDIP−8)
−40 to +85°C
50 Units / Rail
SA5532NG
8−Pin Plastic Dual In−Line Package (PDIP−8)
(Pb−Free)
−40 to +85°C
50 Units / Rail
SE5532AD8
8−Pin Plastic Small Outline (SO−8) Packagee
−55 to +125°C
98 Units / Rail
SE5532AD8G
8−Pin Plastic Small Outline (SO−8) Package
(Pb−Free)
−55 to +125°C
98 Units / Rail
SE5532AD8R2
8−Pin Plastic Small Outline (SO−8) Packagee
−55 to +125°C
2500 / Tape & Reel
SE5532AD8R2G
8−Pin Plastic Small Outline (SO−8) Package
(Pb−Free)
−55 to +125°C
2500 / Tape & Reel
SE5532N
8−Pin Plastic Dual In−Line Package (PDIP−8)
−55 to +125°C
50 Units / Rail
SE5532NG
8−Pin Plastic Dual In−Line Package (PDIP−8)
(Pb−Free)
−55 to +125°C
50 Units / Rail
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
7
NE5532, SA5532, SE5532, NE5532A, SE5532A
PACKAGE DIMENSIONS
SOIC−8 NB
CASE 751−07
ISSUE AG
−X−
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDARD IS 751−07.
A
8
5
S
B
1
0.25 (0.010)
M
Y
M
4
−Y−
K
G
C
N
DIM
A
B
C
D
G
H
J
K
M
N
S
X 45 _
SEATING
PLANE
−Z−
H
0.10 (0.004)
D
0.25 (0.010)
M
Z Y
S
X
M
J
S
SOLDERING FOOTPRINT*
1.52
0.060
7.0
0.275
4.0
0.155
0.6
0.024
1.270
0.050
SCALE 6:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
8
MILLIMETERS
MIN
MAX
4.80
5.00
3.80
4.00
1.35
1.75
0.33
0.51
1.27 BSC
0.10
0.25
0.19
0.25
0.40
1.27
0 _
8 _
0.25
0.50
5.80
6.20
INCHES
MIN
MAX
0.189
0.197
0.150
0.157
0.053
0.069
0.013
0.020
0.050 BSC
0.004
0.010
0.007
0.010
0.016
0.050
0 _
8 _
0.010
0.020
0.228
0.244
NE5532, SA5532, SE5532, NE5532A, SE5532A
PACKAGE DIMENSIONS
8−Pin Plastic Dual In−Line Package (PDIP−8)
N SUFFIX
CASE 626−05
ISSUE L
8
5
−B−
1
4
F
−A−
NOTE 2
L
C
J
−T−
N
SEATING
PLANE
D
H
M
K
G
0.13 (0.005)
M
T A
M
B
M
http://onsemi.com
9
NOTES:
1. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
2. PACKAGE CONTOUR OPTIONAL (ROUND OR
SQUARE CORNERS).
3. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
DIM
A
B
C
D
F
G
H
J
K
L
M
N
MILLIMETERS
MIN
MAX
9.40
10.16
6.10
6.60
3.94
4.45
0.38
0.51
1.02
1.78
2.54 BSC
0.76
1.27
0.20
0.30
2.92
3.43
7.62 BSC
−−−
10_
0.76
1.01
INCHES
MIN
MAX
0.370
0.400
0.240
0.260
0.155
0.175
0.015
0.020
0.040
0.070
0.100 BSC
0.030
0.050
0.008
0.012
0.115
0.135
0.300 BSC
−−−
10_
0.030
0.040
NE5532, SA5532, SE5532, NE5532A, SE5532A
PACKAGE DIMENSIONS
SOIC−16 WB
D SUFFIX
CASE 751G−03
ISSUE C
A
D
9
h X 45_
H
E
0.25
8X
M
B
M
16
q
1
NOTES:
1. DIMENSIONS ARE IN MILLIMETERS.
2. INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.5M, 1994.
3. DIMENSIONS D AND E DO NOT INLCUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.
5. DIMENSION B DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.13 TOTAL IN
EXCESS OF THE B DIMENSION AT MAXIMUM
MATERIAL CONDITION.
MILLIMETERS
DIM MIN
MAX
A
2.35
2.65
A1 0.10
0.25
B
0.35
0.49
C
0.23
0.32
D 10.15 10.45
E
7.40
7.60
e
1.27 BSC
H 10.05 10.55
h
0.25
0.75
L
0.50
0.90
q
0_
7_
8
16X
M
14X
e
T A
S
B
S
A1
L
A
0.25
B
B
SEATING
PLANE
T
C
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any
liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental
damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over
time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under
its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body,
or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death
may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees,
subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of
personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part.
SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800−282−9855 Toll Free
Literature Distribution Center for ON Semiconductor
USA/Canada
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Phone: 81−3−5773−3850
Email: [email protected]
http://onsemi.com
10
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
For additional information, please contact your
local Sales Representative.
NE5532/D