Juxing MASK12 Surface mount schottky rectifier Datasheet

MASK12~MASK110
Surface Mount Schottky Rectifiers
Features
●
Low profile package
●
Ideal for automated placement
●
Ultrafast reverse recovery time
●
Low power losses, high efficiency
●
Low forward voltage drop
●
High surge capability
●
High temperature soldering:
●
Component in accordance to
260℃/10 seconds at terminals
RoHS 2002/95/1 and WEEE 2002/96/EC
Mechanical Date
●
●
Major Ratings and Characteristics
Case: JEDEC MSMA molded plastic
IF(AV)
1.0 A
body over glass passivated chip
VRRM
20 V to 100 V
Terminals: Solder plated, solderable per
IFSM
30 A
VF
0.50V,0.55V,0.70V,0.85V
Tj max.
125 °C
J-STD-002B and JESD22-B102D
●
y Laser band denotes cathode end
Polarity:
Maximum Ratings & Thermal Characteristics
(TA = 25 °C unless otherwise noted)
Items
Symbol
MASK MASK MASK MASK MASK MASK MASK
16
18
12
13
14
15
110
UNIT
Maximum repetitive peak reverse voltage
VRRM
20
30
40
50
60
80
100
V
Maximum RMS voltage
VRMS
14
21
28
35
42
56
70
V
Maximum DC blocking voltage
VDC
20
30
40
50
60
80
100
V
Maximum average forward rectified current
IF(AV)
1.0
A
Peak forward surge current 8.3 ms single half
sine-wave superimposed on rated load
IFSM
30
A
Voltage rate of change (rated VR)
dv/dt
10000
V/µs
RθJL
35
℃/W
TJ,TSTG
–65 to +125
℃
Thermal resistance from junction to lead
(1)
Operating junction and storage temperature
range
Note 1: Mounted on P.C.B. with 0.2 x 0.2” (5.0 x 5.0mm) copper pad areas.
Electrical Characteristics
Items
Instantaneous forward voltage
Reverse current
(TA = 25 °C unless otherwise noted)
Test conditions
Symbol
IF=1.0A(2)
VF
VR=VDC
TA=25℃
TA=100℃
Note 2: Pulse test:300μs pulse width,1% duty cycle.
http://www.trr-jx.com
IR
MASK MASK13~ MASK15~ MASK18~
12
MASK14 MASK16 MASK110
0.50
0.55
0.70
0.5
10
0.85
UNIT
V
mA
MASK12~MASK110
Surface Mount Schottky Rectifiers
Characteristic Curves (TA=25 ℃ unless otherwise noted)
http://www.trr-jx.com
MASK12~MASK110
Surface Mount Schottky Rectifiers
Package Outline
Notice
●
Product is intended for use in general electronics applications.
●
Product should be worked less than the ratings; if exceeded, may cause permanent damage.or introduce latent failure
●
The absolute maximum ratings are rated values and must not be exceeded during operation. The following are the general
mechanisms.
derating methods you design a circuit with a device.
IF(AV) : We recommend that the worst case current be no greater than 80% .
IFSM : This rating specifies the non-repetitive peak current. This is only applied for an abnormal operation, which the general
during the lifespan of the device.
TJ : Derate this rating when using a device in order to ensure high reliability. We recommend that the device be used at
a TJ of below 125°C.
●
TRR is registered trademark of Rising-sun Technology. Rising-sun Technology reserves the right to make changes to any product in this
specification to improve reliability,functional characteristics,or design without notice.
●
Rising-sun Technology does not assure any liability arising out of the applications or any product described in this specification.
●
Rising-sun Technology advises customers to obtain the latest version of the device information before placing orders to verify that the
required information is current.
http://www.trr-jx.com
Similar pages