Freescale MPC7410RX400NE Mpc7410 risc microprocessor hardware specifications addendum Datasheet

Freescale Semiconductor
Advance Information
Document Number: MPC7410ECS02AD
Rev. 2.0, 11/2007
--- Preliminary --MPC7410 RISC Microprocessor
Hardware Specifications Addendum
for the MPC7410xxnnnNE Series
This document describes part number-specific changes to
recommended operating conditions and revised electrical
specifications, as applicable, from those described in the
general MPC7410 Hardware Specifications (Document No.
MPC7410EC).
Specifications provided in this document supersede those in
the MPC7410 Hardware Specifications, for the part numbers
listed in Table A only. Specifications not addressed herein
are unchanged. Because this document is frequently
updated, refer to http://www.freescale.com or to your
Freescale sales office for the latest version.
Note that headings and table numbers in this document are
not consecutively numbered. They are intended to
correspond to the heading or table affected in the general
hardware specification. Part numbers addressed in this
document are listed in Table A. For more detailed ordering
information see Table 17.
This document contains information on a new product. Specifications and information herein
are subject to change without notice.
© Freescale Semiconductor, Inc., 2002, 2007. All rights reserved.
Freescale Part Numbers Affected:
MPC7410RX400NE
MPC7410HX400NE
MPC7410VS400NE
MC7410VU400NE
MPC7410RX450NE
MPC7410HX450NE
MPC7410VS450NE
MC7410VU450NE
Features
Table A. Part Numbers Addressed by this Data Sheet
Operating Conditions
Freescale Part
Number
MPC7410RX400NE
MPC7410HX400NE
MPC7410VS400NE
MC7410VU400NE
MPC7410RX450NE
MPC7410HX450NE
MPC7410VS450NE
MC7410VU450NE
CPU
Frequency
Vdd
TJ (°C)
OVdd
400 MHz
1.5V±50mV
0 to
105
1.8/2.5 V
450 MHz
1.8V
±100mV
0 to
105
450 MHz
1.5V±50mV
0 to
105
500 MHz
1.8V
±100mV
0 to
105
Significant Differences from Hardware
Specification
Reduced core voltage to achieve lower power
consumption. Removes 3.3V OVdd support. For
all AC/DC specifications not mentioned in this
document, please refer to the
MPC7410(RX/HX/VS)400LE and
MC7410VU400LE specifications in the general
MPC7410 Hardware Specifications.
1.8/2.5/3.3 V The MPC7410(RX/HX/VS)400NE and
MC7410VU400NE also fully conform to the
MPC7410(RX/HX/VS)450LE and
MC7410VU450LE specifications, respectively.
Refer to the general MPC7410 Hardware
Specifications.
1.8/2.5 V
Reduced core voltage to achieve lower power
consumption. Removes 3.3V OVdd support. For
all AC/DC specifications not mentioned in this
document, please refer to the
MPC7410(RX/HX/VS)450LE and
MC7410VU450LE specifications in the general
MPC7410 Hardware Specifications.
1.8/2.5/3.3 V The MPC7410(RX/HX/VS)450NE and
MC7410VU400NE also fully conform to the
MPC7410(RX/HX/VS)500LE and
MC7410VU500LE specifications, respectively.
Refer to the general MPC7410 Hardware
Specifications.
2 Features
This section summarizes changes to the features of the MPC7410 described in the MPC7410 Hardware
Specifications.
• Bus interface
— Selectable interface voltages of 1.8 V, 2.5 V (3.3 V not supported)
4.1 DC Electrical Characteristics
Voltage to the L2 I/Os and processor interface I/Os are provided through separate sets of supply pins and
may be provided at the voltages shown in Table 2.
MPC7410 RISC Microprocessor Hardware Specifications Addendum for the MPC7410xxnnnNE Series, Rev. 2.0
2
Freescale Semiconductor
Features
Table 2. Input Threshold Voltage Setting
BVSEL Signal 3
Processor Bus Input
Threshold is Relative to:
L2VSEL Signal 3
L2 Bus Input Threshold is
Relative to:
Note
0
1.8 V
0
1.8 V
1
HRESET
2.5 V
HRESET
2.5 V
1, 2
1
Not Supported
1
2.5 V
1, 4, 5
HRESET
Not Supported
HRESET
Not Supported
—
Notes:
1. Caution: The input threshold selection must agree with the OVdd/L2OVdd voltages supplied.
2. To select the 2.5-V threshold option, BVSEL and/or L2VSEL should be tied to HRESET so that the two signals
change state together. This is the preferred method for selecting this mode of operation.
3. To overcome the internal pull-up resistance, a pull-down resistance less than 250 ohms should be used.
4. Default voltage setting if left unconnected (internal pulled-up).
5. Caution: The XPC7410RXnnnNE does not support the default OVdd setting of 3.3 V. The BVSEL input must be tie
either low or to HRESET.
Table 3 provides the recommended operating conditions for the MPC7410 part numbers described herein.
Table 3. Recommended Operating Conditions
Characteristic
Symbol
Recommended Value
Unit
Core supply voltage
Vdd
1.5V ± 50mV
V
PLL supply voltage
AVdd
1.5V ± 50mV
V
L2AVdd
1.5V ± 50mV
V
OVdd
1.8V ± 100mV
V
BVSEL = HRESET
OVdd
2.5V ± 100mV
V
BVSEL = HRESET
or BVSEL = 1
OVdd
Not Supported
V
L2VSEL = 0
L2OVdd
1.8V ± 100mV
V
L2VSEL = HRESET
or L2VSEL = 1
L2OVdd
2.5V ± 100mV
V
Processor bus and
JTAG Signals
Vin
GND to OVdd
V
L2 Bus
Vin
GND to L2OVdd
V
Tj
0 to 105
°C
L2 DLL supply voltage
Processor bus supply voltage BVSEL = 0
L2 bus supply voltage
Input voltage
Die-junction temperature
Note: These are the recommended and tested operating conditions. Proper device operation outside of
these conditions is not guaranteed.
MPC7410 RISC Microprocessor Hardware Specifications Addendum for the MPC7410xxnnnNE Series, Rev. 2.0
Freescale Semiconductor
3
Features
Table 7 provides the power consumption for the MPC7410 part at the frequencies described herein.
Table 7. Power Consumption for MPC7410
Processor
(CPU)
Frequency
Processor
(CPU)
Frequency
400Mhz
450Mhz
Typical
2.92
3.29
W
1, 3
Maximum
6.6
7.43
W
1, 2,
3.6
4.1
W
1, 2
1.35
1.5
W
1, 2
1.3
1.45
W
1, 2
Unit
Notes
Full-On Mode
Doze Mode
Maximum
Nap Mode
Maximum
Sleep Mode
Maximum
Sleep Mode—PLL and DLL Disabled
Typical
0.6
0.6
W
1, 3
Maximum
1.1
1.1
W
1, 2
Notes:
1. These values apply for all valid processor bus and L2 bus ratios. The values
do not include I/O Supply Power (OVdd and L2OVdd) or PLL/DLL supply
power (AVdd and L2AVdd). OVdd and L2OVdd power is system dependent,
but is typically <10% of Vdd power. Worst case power consumption for AVdd
= 15 mw and L2AVdd = 15 mW.
2. Maximum power is measured at 105 °C and Vdd = 1.5V while running an
entirely cache-resident, contrived sequence of instructions which keep the
execution units, including AltiVec, maximally busy.
3. Typical power is an average value measured at 65 °C and Vdd = 1.5V in a
system while running typical benchmarks.
MPC7410 RISC Microprocessor Hardware Specifications Addendum for the MPC7410xxnnnNE Series, Rev. 2.0
4
Freescale Semiconductor
Document Revision History
9 Document Revision History
Table 16 provides a revision history for this Hardware Specification Addendum.
Table 16. Document Revision History
Revision
Date
Substantive Changes
2.0
11/16/2007
Updated document title to remove “RX” from part number since other non-RX package devices
were added to this specification.
Added MPC7410HX400NE, MPC7410VS400NE, MC7410VU400NE, MPC7410HX450NE,
MPC7410VS450NE, and MC7410VU450NE devices to list on cover page and to Table A.
Updated Table 17 to match corresponding table in MPC7410 Hardware Specifications
1.1
04/19/2005
Document template update
Document ID change from MPC7410RXNEPNS for Part Number Specification to
MPC7410ECS02AD for Hardware Specification Addendum.
1
10/2002
Minor formatting.
Added Section 1.9 Document Revision History.
Section 1.10.1 - added Table 17 - Part Marking Nomenclature.
0
Initial release
MPC7410 RISC Microprocessor Hardware Specifications Addendum for the MPC7410xxnnnNE Series, Rev. 2.0
Freescale Semiconductor
5
Ordering Information
10 Ordering Information
10.1 Part Numbers Addressed by this Specification
Table 17 provides the ordering information for the MPC7410 part described in this document.
Table 17. Part Marking Nomenclature.
Mxx
7410
xx
nnn
N
E
Product
Code
Part
Identifier
Package
Processor
Frequency 1
Application
Modifier
Revision Level
MPC
7410
MC
RX = CBGA
400
450
500
HX = HCTE_CBGA
VS = HCTE_LGA
400
450
N: 1.5 V ± 50 mV
0 to 105 °C
E: 1.4; PVR = 800C 1104
VU = HCTE_CBGA
(Lead Free C5 Solder
Spheres)
Notes:
1. Processor core frequencies supported by parts are addressed by this specification only. Parts addressed by other
specifications may support other maximum core frequencies.
10.3 Part Marking
Parts are marked as the example shown in Figure 26.
MPC7410
RXnnnNE
MMMMMM
ATWLYYWWA
7410
Notes:
BGA
nnn is the speed grade of the part
MMMMMM is the 6-digit mask number
ATWLYYWWA is the traceability code
CCCCC is the country of assembly (this space is left blank if parts are assembled in the United States)
Figure 26. Freescale Part Marking for BGA Device
MPC7410 RISC Microprocessor Hardware Specifications Addendum for the MPC7410xxnnnNE Series, Rev. 2.0
6
Freescale Semiconductor
Ordering Information
THIS PAGE INTENTIONALLY LEFT BLANK
MPC7410 RISC Microprocessor Hardware Specifications Addendum for the MPC7410xxnnnNE Series, Rev. 2.0
Freescale Semiconductor
7
How to Reach Us:
Home Page:
www.freescale.com
email:
[email protected]
USA/Europe or Locations Not Listed:
Freescale Semiconductor
Technical Information Center, CH370
1300 N. Alma School Road
Chandler, Arizona 85224
(800) 521-6274
480-768-2130
[email protected]
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
[email protected]
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of
any product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters which may be
provided in Freescale Semiconductor data sheets and/or specifications can and do
vary in different applications and actual performance may vary over time. All operating
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku
Tokyo 153-0064, Japan
0120 191014
+81 2666 8080
[email protected]
parameters, including “Typicals” must be validated for each customer application by
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate,
Tai Po, N.T., Hong Kong
+800 2666 8080
[email protected]
purchase or use Freescale Semiconductor products for any such unintended or
For Literature Requests Only:
Freescale Semiconductor
Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
(800) 441-2447
303-675-2140
Fax: 303-675-2150
LDCForFreescaleSemiconductor
@hibbertgroup.com
Document Number: MPC7410ECS02AD
Rev. 2.0
11/2007
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Semiconductor was negligent regarding the design or manufacture of the part.
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
All other product or service names are the property of their respective owners. The
Power Architecture and Power.org word marks and the Power and Power.org logos and
related marks are trademarks and service marks licensed by Power.org.
© Freescale Semiconductor, Inc., 2002, 2007. Printed in the United States
of America. All rights reserved.
Similar pages