Features • Stereo Audio DAC – – – – – – 2.7V to 3.3V Analog Supply Operation 2.4V to 3.3V Digital Supply Operation 20-bit Stereo Audio DAC 93 dB SNR Playback Stereo Channels 32 Ohm/20 mW Stereo Headset Drivers with Master Volume and Mute Controls Stereo Line Level Input with Volume Control/mute and Playback through the Headset Drivers – Differential Monaural Auxiliary Input, with Volume Control/mute and Playback through the Headset Drivers – Accepts Mixed Signals from All Signal Paths (Line Inputs, External Mono and DAC Output) – 8, 11.024, 16, 22.05, 24, 32, 44.1 and 48 kHz Sampling Rates – 256x or 384xFs Master Clock Frequency – I2S Serial Audio Interface • Mono Audio Power Amplifier – Supply Input from Main Li-Ion Battery – 440mW on 8 Ohm Load – Low Power Mode for Earphone – Programmable Volume Control (-22 to +20 dB) – Fully Differential Structure, Input and Output – 8 mA Drain Current in Full Power Mode – Power-down mode (Consumption Less than 2 µA) – Minimum External Components (Direct Connection of the Loudspeaker) • Applications: Mobile Phones, Digital Cameras, PDAs, SmartPhones, DECT Phones, Music Players Power Management and Analog Companions (PMAAC) AT73C213B Audio Interface for Portable Handsets 1. Description The AT73C213B is a fully integrated, low-cost, combined stereo audio DAC and audio power amplifier circuit targeted for Li-Ion or Ni-Mh battery powered devices such as mobile phones, smartphones, PDA, DECT phones, digital still cameras, music players or any other type of handheld device where an audio interface is needed. The stereo DAC section is a complete high performance, stereo audio digital-to-analog converter delivering a 93 dB dynamic range. It comprises a multibit sigma-delta modulator with dither, continuous time analog filters and analog output drive circuitry. This architecture provides a high insensitivity to clock jitter. The digital interpolation filter increases the sample rate by a factor of 8 using 3 linear phase half-band filters cascaded, followed by a first order SINC interpolator with a factor of 8. This filter eliminates the images of baseband audio, retaining only the image at 64x the input sample rate, which is eliminated by the analog post filter. Optionally, a dither signal can be added that reduces possible noise tones at the output. However, the use of a multibit sigma-delta modulator already provides extremely low noise tone energy. Master clock is from 256 or 384 times the input data rate, allowing choice of input data rate up to 50 kHz, including standard audio rates of 48, 44.1, 32, 16 and 8 kHz. The DAC section is followed by a volume and mute control and can be simultaneously played back directly through a stereo 32 Ohm headset pair of drivers. 6407A–PMAAC–22-Apr-08 The stereo 32 Ohm headset pair of drivers also includes a mixer of a LINEL and LINER pair of stereo inputs, as well as a differential monaural auxiliary input (line level). The DAC output can be connected through a buffer stage to the input of the audio power amplifier, using 2x coupling capacitors The mono buffer stage also includes a mixer of the LINEL and LINER inputs, as well as a differential monaural auxiliary input (line level) which can be, for example, the output of a voice Codec output driver in mobile phones. The audio power amplifier is a dual-mode AB class amplifier with differential output and programmable volume control. In full power mode, it is capable of driving an 8-ohm loudspeaker at maximum power of 1W at 5V supply and 440 mW at 3.6V supply. In low power mode, it can drive the same loudspeaker as an earpiece, making it suitable as a handsfree speaker driver in wireless handset application. The volume, mute, power down, de-emphasis controls and 16-bit, 18-bit and 20-bit audio formats are digitally programmable via a 4-wire SPI bus and the digital audio data are provided through a multi-format I2S interface. 2. Block Diagram LINER PGA PAINN CBP VBAT HPP AT73C213B Audio PA LLIG: -33 to +12dB in 3dB step + 20dB and mute HPN LPHN PAINP MONO Voltage Reference AUXN GNDB AUXG: -33 to +12dB in 3dB step +20 dB and mute AUXP VREF AT73C213B Functional Block Diagram AVDD Figure 2-1. VDIG APAGAIN -22 to +20dB in 3dB step SPI_DOUT INGND RLIG: -33 to +12dB in 3dB step + 20dB and mute LINEL SPI_DIN Status Registers SPI_CLK SPI SPI_CSB PGA 32 driver + DAC Volume Control + Volume Control VCM ROLC: -6 to +6dB in 3dB step 32 driver HSR + DAC Volume Control + Digital Filter RSTB SMODE SDIN LRFS BCLK AVDDHS RLOG: -46.5dB to 0dB in 1.5dB step and mute MONOP MONO Volume Control MCLK Digital Filter Serial Audio I/F HSL LMPG: -34.5dB to +12dB in 1.5dB step and mute LLOG: -46.5dB to 0dB in 1.5dB step and mute LOLC: -6 to +6dB in 3dB step + RMPG: -34.5dB to +12dB in 1.5dB step and mute GNDD MONON 2 AT73C213B 6407A–PMAAC–22-Apr-08 AT73C213B 3. Pin Description Table 3-1. Pin Description Pin Name I/O Pin Type LPHN O 10 Analog Low power audio stage output HPN O 11 Analog Negative speaker output VBAT I 12 Supply Audio amplifier supply HPP O 13 Analog Positive speaker output CBP O 14 Analog Audio amplifier common mode voltage decoupling PAINN I 15 Analog Audio amplifier negative input PAINP I 16 Analog Audio amplifier positive input SDIN I 17 Digital Audio interface serial data input BCLK I 18 Digital Audio interface bit clock LRFS I 19 Digital Audio interface left/right channel synchronization frame pulse MCLK I 20 Digital Audio interface master clock input RSTB I 21 Digital Master reset (active low) SMODE I 22 Digital Serial interface selection (to connect to ground) GNDD GND 23 Ground Digital ground VDIG I 24 Supply Digital supply SPI_DOUT O 25 Digital SPI data output SPI_DIN I/O 26 Digital SPI data input SPI_CLK I 27 Digital SPI clock SPI_CSB I 28 Digital SPI chip select MONON O 29 Analog Negative monaural driver output MONOP O 30 Analog Positive monaural driver output AUXP I 31 Analog Audio mono auxiliary positive input AUXN I 32 Analog Audio mono auxiliary negative input VREF I 1 Analog Voltage reference pin for decoupling AVDD I 2 Supply Analog supply (DAC + Line in + Aux + Mono out) HSL O 3 Analog Left channel headset driver output HSR O 4 Analog Right channel headset driver output AVDDHS I 5 Supply Headset driver analog supply LINEL I 6 Analog Left channel line in LINER I 7 Analog Right channel line in INGND I 8 Analog Line signal ground pin for decoupling VCM I 9 Analog Common mode reference for decoupling GND 33 (Bottom) Ground Analog ground GNDB Function 3 6407A–PMAAC–22-Apr-08 4. Electrical Characteristics Table 4-1. Absolute Maximum Ratings* Operating Temperature (Industrial)-40°C to +85°C *NOTICE: Storage Temperature-55°C to +150°C Power Supply Input on VBAT-0.3V to +5.5V on VDIG, AVDD-0.3V to +3.6V Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 5. Digital IOs All the digital IOs: SDIN, BCLK, LRFS, MCLK, RSTB, SMODE, SPI_DOUT, SPI_DIN, SPI_CLK, SPI_CSB are referred to as VDIG. Table 5-1. Digital IOs Symbol Parameter Conditions VDIG Min Max Unit VIL Low level input voltage Guaranteed input low Voltage from 2.4Vto 3.3 V -0.3 0.2 x VDIG V VIH High level input voltage Guaranteed input high Voltage from 2.4Vto 3.3 V 0.8 x VDIG VDIG + 0.3 V VOL Low level output voltage IOL = 2 mA from 2.4Vto 3.3 V 0.4 V VOH High level output voltage IOH = 2 mA from 2.4Vto 3.3 V 4 VDIG - 0.5V V AT73C213B 6407A–PMAAC–22-Apr-08 AT73C213B 6. Audio Power Amplifier 6.1 Electrical Specifications VBAT = 3.6V, TA = 25°C unless otherwise noted. High power mode, 100 nF capacitor connected between CBP and GND Audio, load = 8 Ohms. Table 6-1. Audio Power Amplifier Electrical Specifications (General Conditions: VDD = 3.6V,TA = 25°C) Symbol Parameter Conditions Min Typ Max Unit VDD Supply voltage Unloaded, 100 nF decoupling capacitor to GND 3 3.6 5.5 V IDD Quiescent current Inputs shorted, no load 6 8 mA IDDstby Standby current 2 µA VCbp DC reference VOS Output differential offset Full gain -20 0 20 mV ZIN Input impedance Active state 12K 20k 30k Ohm ZLFP Output load Full Power mode 6 8 32 Ohm ZLLP Output load Low-Power mode, including R1 100 150 300 Ohm CL Capacitive load 100 pF PSRR Power supply rejection ratio 200 to 2 kHz differential output 60 dB BWmin Low Frequency Cutoff 1 kHz reference frequency 3 dB attenuation 470 nF input coupling capacitors 50 Hz BWmax High Frequency Cutoff 1 KHz reference frequency 3 dB attenuation tUP Output setup time Off to on mode Voltage already settled Input capacitors precharged VN Output noise Max gain, A weighted 120 THDHP Output distortion High power mode, 1 kHz, Pout = 100mW, gain = 0dB 0.3 % THDLP Output distortion Low power mode,1KHz, V out = 100m Vpp, Max gain, load 8 ohms in series with 200 ohms 1 % Pmax Maximum power High power mode, 1 KHz, Vout = 100 mVpp, Max gain, load 8 ohms in series with 200 ohms 440 mW GACC Overall Gain accuracy GSTEP Gain Step Accuracy VDD/2 V 20 kHz 10 ms 500 µVRMS -2 0 2 dB -0.7 0 0.7 dB 5 6407A–PMAAC–22-Apr-08 7. Audio DAC 7.1 Electrical Specifications AVDD, AVDDHS = 2.8 V, TA = 25°C, typical case, unless otherwise noted. All noise and distortion specifications are measured in the 20 Hz to 0.425xFs and A-weighted filtered. Full-scale levels scale proportionally with the analog supply voltage. Table 7-1. Electrical Specifications Min Typ Max Units Operating Temperature (ambient) -40 +25 +85 °C Analog Supply Voltage (AVDD, AVDDHS) 2.7 2.8 3.3 V Digital Supply Voltage (VDIG) 2.4 2.8 3.3 V Overall DIGITAL INPUTS/OUTPUTS Resolution 20 Logic Family CMOS Logic Coding 2's Complement bits Analog Performance - DAC to Line-out/Headphone Output Output level for full scale input (for AVDD, AVDDHS = 2.8 V) Output common mode voltage Output load resistance (on HSL, HSR) Headphone load Line load 16 7 Output load capacitance (on HSL, HSR) Headphone load Line load Signal to Noise Ratio (-1dBFS @ 1kHz input and 0dB Gain) Line and Headphone loads Vpp 0.5 x AVDDHS V 32 10 Ohm kOhm 30 30 87 Total Harmonic Distortion (-1dBFS @ 1kHz input and 0dB Gain) Line Load Headphone Load Headphone Load (16 Ohm) Dynamic Range (measured with -60 dBFS @ 1kHz input, extrapolated to full-scale) Line Load Headphone Load 1.65 92 0.01 0.06 0.5 88 70 1000 150 pF pF dB 0.016 0.1 1 93 74 % % % dB dB Interchannel mismatch 0.1 1 dB Left-channel to right-channel crosstalk (@ 1kHz) -90 -80 dB 6 dB Output Headset Driver Level Control Range Output Headset Driver Level Control Step 6 -6 3 dB AT73C213B 6407A–PMAAC–22-Apr-08 AT73C213B Table 7-1. Electrical Specifications (Continued) Min PSRR 1 kHz 20 kHz Typ Max 55 50 Maximum output slope at power up (100 to 220 µF coupling capacitor) Units dB dB 3 V/s Analog Performance - Line-in/Microphone Input to Line-out/Headphone Output Input level for full scale output - 0dBFS Level @ AVDD, AVDDHS = 2.8 V and 0 dB gain 1.65 583 0.165 58.3 Vppm Vrms Vppm Vrms 0.5 x AVDD V 7 10 kOhm 81 85 71 dB 82 86 72 dB @ AVDD, AVDDHS = 2.8 V and 20 dB gain Input common mode voltage Input impedance Signal to Noise Ratio -1 dBFS @ 1kHz input and 0 dB gain -21 dBFS @ 1kHz input and 20 dB gain Dynamic Range (extrapolated to full scale level) -60 dBFS @ 1kHz input and 0 dB gain -60 dBFS @ 1kHz input and 20 dB gain Total Harmonic Distortion -1dBFS @ 1kHz input and 0 dB gain -1dBFS @ 1kHz input and 20 dB gain 0.01 0.018 0.016 0.04 % % Interchannel mismatch 0.1 1 dB Left-channel to right-channel crosstalk (@ 1kHz) -90 -80 dB Analog Performance - Differential mono input amplifier Differential input level for full scale output - 0dBFS Level @ AVDD, AVDDHS = 2.8 V and 0 dB gain Input common mode voltage 1.65 583 Vppdif mVrms 0.5xAVDD V Input impedance 7 10 kOhm Signal to Noise Ratio (-1 dBFS @ 1kHz input and 0 dB gain) 76 80 dB Total Harmonic Distortion (-1dBFS @ 1kHz input and 0 dB gain) -85 -81 dB Analog Performance - PA Driver Differential output level for full scale input (for AVDD, AVDDHS = 2.8 V) Output common mode voltage 3.3 Vppdif 0.5 x AVDDHS V 10 kOhm Output load 30 Signal to Noise Ratio (-1dBFS @ 1kHz input and 0dB Gain) 76 80 pF dB 7 6407A–PMAAC–22-Apr-08 Table 7-1. Electrical Specifications (Continued) Min Total Harmonic Distortion (-1dBFS @ 1kHz input and 0dB Gain) Typ Max Units -75 -71 dB 1.5 nspp Master Clock Master Clock Maximum Long Term Jitter Digital Filter Performance Frequency response (10 Hz to 20 kHz) ± 0.1 dB Deviation from linear phase (10 Hz to 20 kHz) ± 0.1 deg 0.4535 Fs Passband 0.1 dB corner Stopband Stopband Attenuation 0.5465 Fs 65 dB De-emphasis Filter Performance (for 44.1kHz Fs) MAX deviation from ideal response -1 1 dB POWER PERFORMANCE Current consumption from Analog supply in power on 9.5 Current consumption from Analog supply in power down Power on Settling Time From full power down to full power up (Vref and VCM decoupling capacitors charge) Line in amplifier (line in coupling capacitors charge) Driver amplifier (out driver DC blocking capacitors charge) 8 mA 10 mA 500 ms 50 500 ms ms AT73C213B 6407A–PMAAC–22-Apr-08 AT73C213B 7.2 Digital Filters Transfer Function Figure 7-1. Channel Filter Figure 7-2. Channel Filter Figure 7-3. De-emphasis Filter FR of DAC Decimator with Deemphasis Fs=44100; OSR=128 0 -2 -4 Gain (dB) -6 -8 -10 -12 3 4 10 10 Frequency (Hz) 9 6407A–PMAAC–22-Apr-08 7.3 Data Interface Normal operation is entered by applying correct LRFS, BCLK and SDIN waveforms to the serial interface, as illustrated in Figure 7-4, Figure 7-5 and Figure 7-6. To avoid noise at the output, the reset state is maintained until proper synchronization is achieved in the serial interface. The data interface allows three different data transfer modes. See Figure 7-4, Figure 7-5 and Figure 7-6. Figure 7-4. 20-bit I2S Justified Mode BCLK LRFS SDIN R1 Figure 7-5. R0 L(N-1) L(N-2) L(N-3) ... L2 L1 L0 R(N-1) R(N-2) R(N-3) ... R2 R1 R0 L2 L1 L0 R(N-1) R(N-2) R(N-3) ... R2 R1 R0 L(N-1) ... L1 L0 R(N-1) R(N-2) ... R1 R0 L(N-1) 20-bit MSB Justified Mode BCLK LRFS SDIN R0 Figure 7-6. L(N-1) L(N-2) L(N-3) ... 20-bit LSB Justified Mode BCLK LRFS SDIN R0 L(N-1) L(N-2) The selection between modes is done using the DINTSEL<1:0> signal. DINTSEL <1:0> Format 00 I2S Justified 01 MSB Justified 1x LSB Justified The data interface always works in slave mode. This means that the LRFS and the BCLK signals are provided by the host controller. In order to achieve proper operation, the LRFS and the BCLK signals must be synchronous with the MCLK master clock signal and their frequency relationship must reflect the selected data mode. For example, if the data mode selected is the 20bit MSB Justified, then the BCLK frequency must be 40 times higher than the LRFS frequency. 10 AT73C213B 6407A–PMAAC–22-Apr-08 AT73C213B 7.4 Timing Specifications The timing constraints of the data interface are described in Figure 7-7 and Table 7-2 below. Figure 7-7. Data Interface Timing Diagram 1 20 M/2+1 M BCLK ts1 th1 LRFS ts2 th2 SDIN Table 7-2. Data Interface Timing Parameters Parameter Min Typ Max Unit ts1 LRFS set-up time before BCLK rising edge 10 ns th1 LRFS hold time after BCLK rising edge 10 ns ts2 DIN set-up time before BCLK rising edge 10 ns th2 DIN hold time after BCLK rising edge 10 ns 11 6407A–PMAAC–22-Apr-08 8. SPI Interface 8.1 Architecture The SPI is a three-wire bi-directional asynchronous serial link. It works only in slave mode. The protocol is the following: Figure 8-1. SPI Architecture SPI_CSB SPI_CLK rw a6 a5 a4 a3 a2 a1 a0 d7 d6 d5 d4 d3 d2 d1 d0 SPI_DIN d7 d6 d5 d4 d3 d2 d1 d0 SPI_DOUT 8.2 SPI Protocol On SPI_DIN, the first bit is a read/write bit. 0 indicates a write operation, while 1 is for a read operation. The seven following bits are used for the register address and the eight last ones are the write data. For both address and data, the most significant bit is the first one. In case of a read operation, SPI_DOUT provides the contents of the read register, MSB first. The transfer is enabled by the CSB signal active low. When no operation is being carried out, SPI_DOUT is set high impedance to allow sharing of MCU serial interface with other devices. The interface is reset at every rising edge of SPI_CSB in order to come back to an idle state, even if the transfer does not succeed. The SPI is synchronized with the serial clock SPI_CLK. Falling edge latches SPI_DIN input and rising edge shifts SPI_DOUT output bits. Note that MCLK must run during any SPI write access from address 0x00 to 0x0D. 12 AT73C213B 6407A–PMAAC–22-Apr-08 AT73C213B 8.3 SPI Interface Timing Figure 8-2. SPI Timing SPI_CSB Tc Tssen Thsen Twl SPI_CLK Twh Tssdi Thsdi SPI_DIN Tdsdo Thsdo SPI_DOUT Table 8-1. SPI Timing Parameters Parameter Description Min Max Tc SPI_CLK min period 100 ns - Twl SPI_CLK min pulse width low 50 ns - Twh SPI_CLK min pulse width high 50 ns - Tssen Setup time SPI_CSB falling to SPI_CLK rising 50 ns - Thsen Hold time SPI_CLK falling to SPI_CSB rising 50 ns - Tssdi Setup time SPI_DIN valid to SPI_CLK falling 20 ns - Thsdi Hold time SPI_CLK falling to SPI_DIN not valid 20 ns - Tdsdo Delay time SPI_CLK rising to SPI_DOUT valid - 20 ns Thsdo Hold time SPI_CLK rising to SPI_DOUT not valid 0 ns - 13 6407A–PMAAC–22-Apr-08 8.4 SPI User Interface Table 8-2. SPI Register Mapping Address Register Name Access Reset State 0x00 DAC_CTRL DAC Control Read/Write 0x00 0x01 DAC_LLIG DAC Left Line In Gain Read/Write 0x05 0x02 DAC_RLIG DAC Right Line In Gain Read/Write 0x05 0x03 DAC_LPMG DAC Left Master Playback Gain Read/Write 0x08 0x04 DAC_RPMG DAC Right Master Playback Gain Read/Write 0x08 0x05 DAC_LLOG DAC Left Line Out Gain Read/Write 0x00 0x06 DAC_RLOG DAC Right Line Out Gain Read/Write 0x00 0x07 DAC_OLC DAC Output Level Control Read/Write 0x22 0x08 DAC_MC DAC Mixer Control Read/Write 0x09 0x09 DAC_CSFC DAC Clock and Sampling Frequency Control Read/Write 0x00 0x0A DAC_MISC DAC Miscellaneous Read/Write 0x00 0x0C DAC_PRECH DAC Precharge Control Read/Write 0x00 0x0D DAC_AUXG DAC Auxiliary Input Gain Control Read/Write 0x05 0x10 DAC_RST DAC Reset Read/Write 0x00 0x11 PA_CRTL Power Amplifier Control Read/Write 0x00 Note: 14 MSB = Bit 7, LSB = Bit 0 AT73C213B 6407A–PMAAC–22-Apr-08 AT73C213B 8.5 DAC Control Register Register Name: DAC_CTRL Reset State: 0x00 Access: Read/Write 7 ONPADRV 6 ONAUXIN 5 ONDACR 4 ONDACL 3 ONLNOR 2 ONLNOL 1 ONLNIR 0 ONLNIL • ONLNIL Left channel line in amplifier (L to power down, H to power up) • ONLNIR Right channel line in amplifier (L to power down, H to power up) • ONLNOL Left channel line out driver (L to power down, H to power up) • ONLNOR Right channel line out driver (L to power down, H to power up) • ONDACL Left channel DAC (L to power down, H to power up) • ONDACR Right channel DAC (L to power down, H to power up) • ONAUXIN Differential mono auxiliary input amplifier (L to power down, H to power up) • ONPADRV Differential mono PA driver (L to power down, H to power up) 15 6407A–PMAAC–22-Apr-08 8.6 DAC Left Line In Gain Register Register Name: DAC_LLIG Reset State: 0x05 Access: Read/Write 7 0 6 0 5 0 4 3 2 LLIG 1 0 • LLIG: Left channel line in analog gain selector LLIG<4:0> Gain Unit 00000 20 dB 00001 12 dB 00010 9 dB 00011 6 dB 00100 3 dB 00101 0 dB 00110 -3 dB 00111 -6 dB 01000 -9 dB 01001 -12 dB 01010 -15 dB 01011 -18 dB 01100 -21 dB 01101 -24 dB 01110 -27 dB 01111 -30 dB 10000 -33 dB ≥10001 < -60 dB 16 AT73C213B 6407A–PMAAC–22-Apr-08 AT73C213B 8.7 DAC Right Line In Gain Register Register Name: DAC_RLIG Reset State: 0x05 Access: Read/Write 7 0 6 0 5 0 4 3 2 RLIG 1 0 • RLIG: Right channel line in analog gain selector RLIG<4:0> Gain Unit 00000 20 dB 00001 12 dB 00010 9 dB 00011 6 dB 00100 3 dB 00101 0 dB 00110 -3 dB 00111 -6 dB 01000 -9 dB 01001 -12 dB 01010 -15 dB 01011 -18 dB 01100 -21 dB 01101 -24 dB 01110 -27 dB 01111 -30 dB 10000 -33 dB ≥10001 < -60 dB 17 6407A–PMAAC–22-Apr-08 8.8 DAC Left Master Playback Gain Register Register Name: DAC_LMPG Reset State: 0x08 Access: Read/Write 7 0 6 0 5 4 3 2 1 0 LMPG • LMPG: Left channel master playback digital gain selector LMPG<5:0> Gain Unit LMPG<5:0> Gain Unit 000000 12.0 dB 010001 -13.5 dB 000001 10.5 dB 010010 -15.0 dB 000010 9.0 dB 010011 -16.5 dB 000011 7.5 dB 010100 -18.0 dB 000100 6.0 dB 010101 -19.5 dB 000101 4.5 dB 010110 -21.0 dB 000110 3.0 dB 010111 -22.5 dB 000111 1.5 dB 011000 -24.0 dB 001000 0.0 dB 011001 -25.5 dB 001001 -1.5 dB 011010 -27.0 dB 001010 -3.0 dB 011011 -28.5 dB 001011 -4.5 dB 011100 -30.0 dB 001100 -6.0 dB 011101 -31.5 dB 001101 -7.5 dB 011110 -33.0 dB 001110 -9.0 dB 011111 -34.5 dB 001111 -10.5 dB ≥ 100000 mute dB 010000 -12.0 dB 18 AT73C213B 6407A–PMAAC–22-Apr-08 AT73C213B 8.9 DAC Right Master Playback Gain Register Register Name: DAC_RMPG Reset State: 0x08 Access: Read/Write 7 0 6 0 5 4 3 2 1 0 RMPG • RMPG: Right channel master playback digital gain selector RMPG<5:0> Gain Unit RMPG<5:0> Gain Unit 000000 12.0 dB 010001 -13.5 dB 000001 10.5 dB 010010 -15.0 dB 000010 9.0 dB 010011 -16.5 dB 000011 7.5 dB 010100 -18.0 dB 000100 6.0 dB 010101 -19.5 dB 000101 4.5 dB 010110 -21.0 dB 000110 3.0 dB 010111 -22.5 dB 000111 1.5 dB 011000 -24.0 dB 001000 0.0 dB 011001 -25.5 dB 001001 -1.5 dB 011010 -27.0 dB 001010 -3.0 dB 011011 -28.5 dB 001011 -4.5 dB 011100 -30.0 dB 001100 -6.0 dB 011101 -31.5 dB 001101 -7.5 dB 011110 -33.0 dB 001110 -9.0 dB 011111 -34.5 dB 001111 -10.5 dB ≥ 100000 mute dB 010000 -12.0 dB 19 6407A–PMAAC–22-Apr-08 8.10 DAC Left Line Out Gain Register Register Name: DAC_LLOG Reset State: 0x00 Access: Read/Write 7 0 6 0 5 4 3 2 1 0 LLOG • LLOG: Left channel line out digital gain selector LLOG<5:0> Gain Unit LLOG<5:0> Gain Unit 000000 0.0 dB 010000 -24.0 dB 000001 -1.5 dB 010001 -25.5 dB 000010 -3.0 dB 010010 -27.0 dB 000011 -4.5 dB 010011 -28.5 dB 000100 -6.0 dB 010100 -30.0 dB 000101 -7.5 dB 010101 -31.5 dB 000110 -9.0 dB 010110 -33.0 dB 000111 -10.5 dB 010111 -34.5 dB 001000 -12.0 dB 011000 -36.0 dB 001001 -13.5 dB 011001 -37.5 dB 001010 -15.0 dB 011010 -39.0 dB 001011 -16.5 dB 011011 -40.5 dB 001100 -18.0 dB 011100 -42.0 dB 001101 -19.5 dB 011101 -43.5 dB 001110 -21.0 dB 011110 -45.0 dB 001111 -22.5 dB 011111 -46.5 dB ≥ 100000 mute dB 20 AT73C213B 6407A–PMAAC–22-Apr-08 AT73C213B 8.11 DAC Right Line Out Gain Register Register Name: DAC_RLOG Reset State: 0x00 Access: Read/Write 7 0 6 0 5 4 3 2 1 0 RLOG • RLOG: Right channel line out digital gain selector RLOG<5:0> Gain Unit RLOG<5:0> Gain Unit 000000 0.0 dB 010000 -24.0 dB 000001 -1.5 dB 010001 -25.5 dB 000010 -3.0 dB 010010 -27.0 dB 000011 -4.5 dB 010011 -28.5 dB 000100 -6.0 dB 010100 -30.0 dB 000101 -7.5 dB 010101 -31.5 dB 000110 -9.0 dB 010110 -33.0 dB 000111 -10.5 dB 010111 -34.5 dB 001000 -12.0 dB 011000 -36.0 dB 001001 -13.5 dB 011001 -37.5 dB 001010 -15.0 dB 011010 -39.0 dB 001011 -16.5 dB 011011 -40.5 dB 001100 -18.0 dB 011100 -42.0 dB 001101 -19.5 dB 011101 -43.5 dB 001110 -21.0 dB 011110 -45.0 dB 001111 -22.5 dB 011111 -46.5 dB ≥ 100000 mute dB 21 6407A–PMAAC–22-Apr-08 8.12 DAC Output Level Control Register Register Name: DAC_OLC Reset State: 0x22 Access: Read/Write 7 RSHORT 6 5 ROLC 4 3 LSHORT 2 1 LOLC 0 • LOLC: Left channel output level control selector LOLC Gain Unit 000 6 dB 001 3 dB 010 0 dB 011 -3 dB ≥ 100 -6 dB • LSHORT: Left channel short circuit indicator Persistent; after being set, bit is not cleared automatically even after the short circuit is eliminated; must be cleared by reset cycle or direct register write operation. • ROLC: Right channel output level control selector ROLC Gain Unit 000 6 dB 001 3 dB 010 0 dB 011 -3 dB ≥ 100 -6 dB • RSHORT: Right channel short circuit indicator Persistent; after being set, bit is not cleared automatically even after the short circuit is eliminated; must be cleared by reset cycle or direct register write operation. 22 AT73C213B 6407A–PMAAC–22-Apr-08 AT73C213B 8.13 DAC Mixer Control Register Register Name: DAC_MC Reset State: 0x09 Access: Read/Write 7 0 6 0 5 INVR 4 INVL 3 RMSMIN2 2 RMSMIN1 1 LMSMIN2 0 LMSMIN1 • LMSMIN1: Left Channel Mono/Stereo Mixer Left Mixed input enable (H to enable, L to disable) • LMSMIN2: Left Channel Mono/Stereo Mixer Right Mixed input enable (H to enable, L to disable) • RMSMIN1: Right Channel Mono/Stereo Mixer Left Mixed input enable (H to enable, L to disable) • RMSMIN2: Right Channel Mono/Stereo Mixer Right Mixed input enable (H to enable, L to disable) • INVL: Left channel mixer output invert (H to enable, L to disable) • INVR: Right channel mixer output invert (H to enable, L to disable) 8.13.1 Digital Mixer Control The Audio DAC features a digital mixer that allows the mixing and selection of multiple input sources. The mixing/multiplexing functions are described in Figure 8-3 and Table 8-3. Figure 8-3. Digital Mixer Functions Left channel Volume Control 1 + Volume Control 2 From digital filters To DACs 1 Volume Control + 2 Volume Control Right channel Note: Table 8-3. When the two mixer inputs are selected, a -6 dB gain is applied to the output signal. When only one input is selected, no gain is applied. Digital Mixer Signal Description Signal Description LMSMIN1 Left Channel Mono/Stereo Mixer Left Mixed input enable - High to enable, Low to disable LMSMIN2 Left Channel Mono/Stereo Mixer Right Mixed input enable - High to enable, Low to disable RMSMIN1 Right Channel Mono/Stereo Mixer Left Mixed input enable - High to enable, Low to disable RMSMIN2 Right Channel Mono/Stereo Mixer Right Mixed input enable - High to enable, Low to disable 23 6407A–PMAAC–22-Apr-08 8.14 DAC Clock and Sampling Frequency Control Register Register Name: DAC_CSFC Reset State: 0x00 Access: Read/Write 7 0 6 0 5 0 4 OVRSEL 3 0 2 0 1 0 0 0 • OVRSEL: Master clock selector L to 256 x Fs, H to 384 x Fs Master clock and sampling frequency selection Table 8-4 describes the modes available for master clock and sampling frequency selection. Table 8-4. 24 Master Clock Modes OVRSEL Master Clock 0 256 x Fs 1 384 x Fs AT73C213B 6407A–PMAAC–22-Apr-08 AT73C213B 8.15 DAC Miscellaneous Register Register Name: DAC_MISC Reset State: 0x00 Access: Read/Write 7 VCMCAPSEL 6 0 5 4 DINTSEL 3 DITHEN 2 DEEMPEN 1 0 NBITS • NBITS<1:0>: Data interface word length The selection of input sample size is done using the NBITS field. NBITS <1:0> Format 00 16 bits 01 18 bits 10 20 bits • DEEMPEN: De-emphasis enable (L to disable, H to enable) To enable the de-emphasis filtering the DEEMPHEN signal must be set to high. • DITHEN: Dither enable (L to disable, H to enable) The dither option (added in the playback channel) is enabled by setting the DITHEN signal to high. • DINTSEL<1:0>: I2S data format selector The selection between modes is done using the DINTSEL<1:0> signal. DINTSEL<1:0> Format 00 I2S Justified 01 MSB Justified 1x LSB Justified • VCMCAPSEL: VCM decoupling capacitor selector L for 10 µF, H for 100 µF 25 6407A–PMAAC–22-Apr-08 8.16 DAC Precharge Control Register Register Name: DAC_PRECH Reset State: 0x00 Access: Read/Write 7 6 5 4 3 2 1 0 PRCHGPDRV PRCHGAUX1 PRCHGLNOR PRCHGLNOL PRCHGLNIR PRCHGLNIL PRCHG ONMSTR • ONMSTR: Master power on control (L to power down, H to power up) • PRCHARGE: Master pre-charge (H to charge) • PRCHARGELNIL: Left channel line in pre-charge (H to charge) • PRCHARGELNIR: Right channel line in pre-charge (H to charge) • PRCHARGELNOL: Left channel line out pre-charge (H to charge) • PRCHARGELNOR: Right channel line out pre-charge (H to charge) • PRCHARGEAUXIN: Differential mono auxiliary input pre-charge (H to charge) • PRCHARGEPADRV: Differential mono PA driver pre-charge (H to charge) 26 AT73C213B 6407A–PMAAC–22-Apr-08 AT73C213B 8.17 DAC Auxiliary Input Gain Control Register Register Name: DAC_AUXG Reset State: 0x05 Access: Read/Write 7 0 6 0 5 0 4 3 2 AUXG 1 0 • AUXG: Differential mono auxiliary input analog gain selector AUXG<4:0> Gain Unit 00000 20 dB 00001 12 dB 00010 9 dB 00011 6 dB 00100 3 dB 00101 0 dB 00110 -3 dB 00111 -6 dB 01000 -9 dB 01001 -12 dB 01010 -15 dB 01011 -18 dB 01100 -21 dB 01101 -24 dB 01110 -27 dB 01111 -30 dB 10000 -33 dB ≥ 10001 < -60 dB 27 6407A–PMAAC–22-Apr-08 8.18 DAC Reset Register Register Name: DAC_RST Reset State: 0x00 Access: Read/Write 7 – 6 – 5 – 4 – 3 – 2 RESMASK 1 RESFILZ 0 RSTZ • RSTZ: Active low reset of the audio codec • RESFILZ: Active low reset of the audio codec filter • RESMASK: Active high reset mask of the audio codec See “Supplies and Start-up” on page 30. 28 AT73C213B 6407A–PMAAC–22-Apr-08 AT73C213B 8.19 PA Control Register Register Name: PA_CTRL Reset State: 0x00 Access: Read/Write 7 – 6 APAON 5 APAPRECH 4 APALP 3 2 1 0 APAGAIN • APAGAIN<3:0>: Audio power amplifier gain APAGAIN<3:0> Gain db APAGAIN<3:0> Gain db 0000 FORBIDDEN 1000 -1 0001 20 1001 -4 0010 17 1010 -7 0011 14 1011 -10 0100 11 1100 -13 0101 8 1101 -16 0110 5 1110 -19 0111 2 1111 -22 • APALP: Audio power amplifier low power bit 0: High power 1: Low power • APAPRECH: Audio power amplifier precharge bit • APAON: Audio power amplifier on bit APAON APAPRECH Operating Mode 0 0 Stand-by 0 1 Input capacitors precharge 1 0 Active mode 1 1 Forbidden state 29 6407A–PMAAC–22-Apr-08 9. Supplies and Start-up In operating mode, VBAT (supply of the audio power amplifier) must be between 3V and 5.5V and AVDD, AVDDHS and VDIG must be inferior or equal to VBAT. A typical application is VBAT connected to a battery and AVDD, AVDDHS and VDIG supplied by regulators. VBAT must be present at the same time or before AVDD, AVDDHS and VDIG. RSTB must be active (0) until the voltages are stable and reach the proper values. To avoid noise issues, it is recommended to use ceramic decoupling capacitors for each supply close to the package. See Figure 11-1 on page 32. The track of the supplies must be optimized to minimize the resistance, especially on VBAT where all the current from the power amplifier comes from. HPN and HPP must be routed symmetrically and the resistance must be minimized. 9.1 Audio DAC Start-up Sequences In order to minimize the noise during the start-up, a specific sequence should be applied. In any audio configuration, always force Bit 2 to high level (“1”) at 0x0B address. 9.1.1 Power on Example Path DAC to headset output 1. Write @0x10 => 0x03 (deassert the reset) 2. Write @0x0C => 0xFF (precharge + master on) 3. Write @0x00 => 0x30 (ONLNOL and ONLONOR set to 1) 4. Delay 500 ms 5. Write @0x0C => 0x01 (precharge off + master on) 6. Delay 1ms 7. Write @0x00 => 0x3C (ONLNOL, ONLNOR, ONDACR and ONDACL set to 1) 9.1.2 Power off Example 1. Write @0x00 => 0x30 (ONDACR and ONDACL set to 0) 2. Write @0x0C => 0x00 (master off) 3. Delay 1ms 4. Write @0x00 => 0x00 (all off) 9.1.3 I2S Example In order to prevent I2S from generating noise at the output (for example a MP3 player switching from one song to another): 1. Set ONDAC to 0 ((bit 4 and 5 in register @0x00) 2. Stop I2S and MCLK When I2S is restarted, in order to prevent noise generation at the output: 1. Start MCLK 2. Write @0x10 => 0x07 (RSTMSK=1) 3. Write @0x10 => 0x04 (RESFILZ=0, RSTZ=0) 4. Write @0x10 => 0x07 (RESFILZ=1, RSTZ=1) 30 AT73C213B 6407A–PMAAC–22-Apr-08 AT73C213B 5. Write @0x10 => 0x03 (RSTMSK=0) 6. Delay 5 ms 7. Set ONDAC to 1 (bit 4 and 5 in register @0x00) 8. Reprogram all DAC settings (Audio format, gains, etc.) 9. Start I2S. 9.2 Audio Power Amplifier Power on Sequence To avoid an audible “click” at start-up, the input capacitors must be pre-charged before the power amplifier. 1. At start-up, set APAON off, APAGAIN<3:0> set to -22 dB, set APAPRECHARGE to 1. 2. Wait 50 ms minimum. 3. Then disable APAPRECH and set APAON. 4. Wait 10 ms min time. 5. Set the gain to the value chosen. 9.2.1 Audio Power Amplifier Power off Sequence To avoid an audible “click” at power-off, the gain should be set to the minimum gain (-22 dB) before turning off the power amplifier. 10. Current Consumption in Different Modes Table 10-1. Current Consumption in Different Modes Mode Current Consumption (typ) Current Consumption (max) Unit 0: Off 5 12 uA 1: Standby 250 350 uA 2: DAC Playback through Stereo Headset (Current in the load not included) 5100 6700 uA 3: Stereo DAC Playback to Audio PA (Current in the load not included) 9500 13500 uA 4: Playback from Mono in to Audio PA (Current in the load not included) 6200 10500 uA 5: Playback from Stereo Line Input to Stereo Headset (Current in the load not included) 1600 3300 uA 31 6407A–PMAAC–22-Apr-08 11. Application Diagram Figure 11-1. Application Using One Li-Ion Battery PAINN AT73C213 22u 3.6 V VBAT Battery (Li-Ion or 3 x NiMh or NiCd) 100n 2.8V from LDO VDIG C17 100n C16 CBP 2.8V from LDO AVDD C7 HPP C18 8 8 Ohm Loudspeaker 100n Audio PA HPN 200 C15 AVDDHS C19 LPHN 10µF R1 PAINP C9 470n MONOP VREF REF 470n 10u MONON C12 R VCM C8 LINER stereo line input C11 (e.g. FM Radio) mono 10u SPI_DOUT C3 470n L SPI_DIN LINEL SPI_CLK mono input 470n (+) 470n mono input (-) 470n AUXP DIG differential input 32 C1 SMODE AUXN 100u RSTB Reset active low MCLK C6 C4 HSR 32 Ohm Headset SPI SPI_CSB C5 HSL 32 or Line Out 100u Audio DAC SDIN LRFS I2S BCLK 10u INGND C10 GNDB 32 GNDD AT73C213B 6407A–PMAAC–22-Apr-08 AT73C213B 12. Components List Table 12-1. Components List Reference Value Techno Size Manufacturer & Reference C1, C3, C4, C8, C12, C15 470 nF Ceramic 0402 C1005X5R0J474K (TDK) or GRM155R60J474KE18 (Murata®) C5, C6 100 µF Ceramic 1210 C3225X5R0J107M (TDK) or GRM32ER60J107ME20 (Murata) C9, C10, C11, C19 10 µF Ceramic 0603 C1608X5R0J106MT (TDK) or GRM188R60J106ME47 (Murata) C7, C17, C18 100 nF Ceramic 0402 C1005X5R1C104KT (TDK) or GRM155R61A104KA01 (Murata) C16 22 µF Ceramic 0805 C2012X5R0J226MT (TDK) or GRM21BR60J226ME39 (Murata) R1 200 Ohms 0603 33 6407A–PMAAC–22-Apr-08 13. Package Drawing Figure 13-1. Package Outline Note: Notes: 1.All Dimensions are in mm 2 Package WARPAGE Max: 0.08 mm 1. All dimensions are in mm. 2. Drawing is for general information only. Refer to JEDEC drawing MO-220 for additional information. 34 AT73C213B 6407A–PMAAC–22-Apr-08 AT73C213B Figure 13-2. Package Drawing with Pin 1 and Marking 33 … 31 32 AT73C213B AT73C213 YY WW XXXXXXXXX 1 2 … 35 6407A–PMAAC–22-Apr-08 14. Revision History Table 14-1. Revision History Doc. Rev. Comments 6704A First issue. 36 Change Request Ref. AT73C213B 6407A–PMAAC–22-Apr-08 Headquarters International Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309 78054 Saint-Quentin-enYvelines Cedex France Tel: (33) 1-30-60-70-00 Fax: (33) 1-30-60-71-11 Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Technical Support Atmel techincal support [email protected] Sales Contacts www.atmel.com/contacts/ Product Contact Web Site www.atmel.com Analog Companions (PMAAC) Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © Atmel Corporation 2008. All rights reserved. Atmel ®, logo and combinations thereof are and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. 6407A–PMAAC–22-Apr-08