CRO3387A 9939 Via Pasar • San Diego, CA 92126 TEL (858) 621-2700 FAX (858) 621-2722 VOLTAGE CONTROLLED OSCILLATOR Rev A1 PHASE NOISE (1 Hz BW, typical) -60 £(f) (dBc/Hz) -70 FEATURES • Frequency Range: 3271 - 3503 MHz • Tuning Voltage: 0.1-16 Vdc • MINI-16 - Style Package -80 -90 -100 -110 -120 -130 APPLICATIONS • Point to Point Radio • Fixed Wireless Equipment • Satellite Communications -140 1 E+3 10 E+3 100 E+3 OFFSET (Hz) VALUE UNITS 3271 - 3503 MHz -101 dBc/Hz Harmonic Suppression (2nd, typ.) Tuning Voltage Tuning Sensitivity (avg.) -18 0.1-16 20 dBc Vdc MHz/V Power Output 5.5±2.5 dBm PERFORMANCE SPECIFICATIONS Oscillation Frequency Range Phase Noise @ 10 kHz offset (1 Hz BW, typ.) Load Impedance 50 Input Capacitance (max.) 50 Pushing <2 MHz/V Pulling (14 dB Return Loss, Any Phase) pF <1 MHz Operating Temperature Range -40 to 85 °C Package Style MINI-16 POWER SUPPLY REQUIREMENTS Supply Voltage (Vcc, nom.) Supply Current (Icc, typ.) 8 Vdc 30 mA All specifications are typical unless otherwise noted and subject to change without notice. APPLICATION NOTES • AN-100/1 : Mounting and Grounding of VCOs • AN-102 : Proper Output Loading of VCOs • AN-107 : How to Solder Z-COMM VCOs NOTES: © Z-Communications, Inc. Page 1 All rights reserved LOW COST - HIGH PERFORMANCE VOLTAGE CONTROLLED OSCILLATOR CRO3387A PAGE 2 FREQUENCY (MHz) TUNING CURVE, typ. 3540 3515 3490 3465 3440 3415 3390 3365 3340 3315 3290 3265 3240 3215 3190 3165 -40 °c °c °c 25 °c 85 25 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 TUNING VOLTAGE (Vdc) POWER OUTPUT (dBm) POWER CURVE, typ. 10 9 8 7 6 5 4 3 2 1 0 3173 3237 3286 3328 3365 3400 3431 3457 3479 3499 3516 FREQUENCY (MHz) PHYSICAL DIMENSIONS TYPICAL OF ALL PADS MINI-16 415-0061 REV. D (DRAWING NOT TO SCALE) SEE NOTE 3 .070 .037 NOTES: 1. THE INSIDE RADIUS OF ALL 16 HALF HOLES AT THE PERIMETER OF THE BOARD ARE PLATED TO PROVIDE A SURFACE FOR THE ATTACHMENT OF THE VCO TO A PCB, IN 13 LOCATIONS, WITH 3 PADS BEING USED FOR ELECTROMECHANICAL INTERFACE. 16 SOLDER LOCATIONS REQUIRED. 2. THE SURFACE OF THE SHIELD IS TIN PLATED AND MAY BE SOLDERED TO. THE SHIELD'S BASE METAL IS COLD ROLLED STEEL. 3. THE GROUND PLANE IS GROUND AND ATTACHES TO A GROUND TRACK ON THE UPPER SIDE OF THE BOARD AS WELL AS THE SHIELD BY PTH. 4. UNLESS OTHERWISE NOTED ALL DIMENSIONS ARE IN INCHES. 5. UNLESS OTHERWISE NOTED ALL TOLERANCES ARE AS FOLLOWS: TOLERANCES .XXX= ± .010 .031 .052 .114 0.500 0.500 0.475 DETAIL A P2 0.415 0.405 0.305 0.315 P3 0.205 -.005 P1=VT P2=RF OUT P3=Vcc TABS RANGE: SEE NOTE 5. (4 PLACES) 0.215 .465 0.475 0.420 0.320 0.000 0.115 0.220 .026 BOTTOM VIEW 0.105 0.115 SEE DETAIL 'A' P1 .220 .070 TYP .150 0.500 0.385 .034 0.000 0.285 0.185 0.085 0.025 0.025 0.000 TYP GROUND PLANE SOLDER PLATED © Z-Communications, Inc. Page 2 Printed in the U.S.A.