EDB101 THRU EDB106 GLASS PASSIVATED SUPER FAST SILICON SURFACE MOUNT BRIDGE RECTIFIER VOLTAGE RANGE 50 to 400 Volts CURRENT 1.0 Ampere FEATURES * * * * * * * * Good for automatic insertion Surge overload rating - 30 amperes peak Ideal for printed circuit board Reliable low cost construction utilizing molded Glass passivated device Polarity symbols molded on body Mounting position: Any Weight: 1.0 gram DB-1 .255 ( 6.5 ) .245 ( 6.2 ) MECHANICAL DATA * UL listed the recongnized component directory,file #94233 * Epoxy: Device has UL flammability classification 94V-O .350 ( 8.9 ) .300 ( 7.6 ) .335 ( 8.51 ) .320 ( 8.12 ) .135 ( 3.4 ) .115 ( 2.9 ) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS .165 ( 4.2 ) .020 Ratings at 25 o C ambient temperature unless otherwise specified. .155 ( 3.9 ) ( 0.5 ) Single phase, half wave, 60 Hz, resistive or inductive load. .205 ( 5.2 ) For capacitive load, derate current by 20%. .195 ( 5.0 ) .060 ( 1.5 ) Dimensions in inches and (millimeters) MAXIMUM RATINGS (At T A = 25oC unless otherwise noted) SYMBOL EDB101 EDB102 EDB103 EDB104 EDB105 EDB106 UNITS Maximum Recurrent Peak Reverse Voltage RATINGS VRRM 50 100 150 200 300 400 Volts Maximum RMS Bridge Input Voltage VRMS 35 70 105 140 210 280 Volts Maximum DC Blocking Voltage VDC 50 100 150 200 300 400 Maximum Average Forward Output Current at T A = 55 oC Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Thermal Resistance (Note 3) Typical Junction Capacitance (Note 2) 1.0 Amps I FSM 30 Amps R qJA 38 RqJL 12 CJ 0 15 C/W pF 10 -55 to + 150 T J, T STG Operating and Storage Temperature Range Volts IO 0 C o ELECTRICAL CHARACTERISTICS (At TA = 25 C unless otherwise noted) CHARACTERISTICS SYMBOL VF Maximum Forward Voltage at 1.0A DC o Maximum Reverse Current at Rated @T A = 25 C DC Blocking Voltage per element @T A = 100 o C Maximum Reverse Recovery Time (Note 1) Note: 1.Test Conditions: I F=0.5A,I R=-1.0A,I RR=-0.25A. 2.Measured at 1MHz and applied reverse voltage of 4.0 volts. 3.Thermal Resistance : Mounted on PCB. IR trr EDB101 EDB102 EDB103 EDB104 1.05 EDB105 EDB106 1.35 1.70 UNITS Volts 5.0 mAmps 100 mAmps 50 nSec 2006-11 REV:B RATING AND CHARACTERISTICS CURVES ( EDB101 THRU EDB106 ) 50 W NONINDUCTIVE (+) 25 Vdc (approx) (-) (-) D.U.T PULSE GENERATOR (NOTE 2) 1 NONINDUCTIVE trr +0.5A 10 W NONINDUCTIVE OSCILLOSCOPE (NOTE 1) 0 -0.25A (+) NOTES: 1 Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF. -1.0A 2. Rise Time = 10ns max. Source Impedance = 50 ohms. 1cm SET TIME BASE FOR 10 ns/cm 2.0 1.0 Single Phase Half Wave 60Hz Resistive or Inductive Load 0 0 25 50 75 100 125 150 LEAD TEMPERATURE, (OC) FIG.2 TYPICAL FORWARD CURRENT DERATING CURVE 175 INSTANTANEOUS REVERSE CURRENT, (mA) AVERAGE FORWARD CURRENT, (A) FIG.1 TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 1000 100 TA = 100 OC TA = 75 OC 10 TA = 25 OC 1.0 0.1 0 20 40 60 80 100 120 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) FIG.3 TYPICAL REVERSE CHARACTERISTICS 140 PEAK FORWARD SURGE CURRENT, (A) 100 TJ = 25 C O 05 B1 B1 01 ~E 1.0 ED DB 10 4 ~E DB 10 6 10 ED 0.1 0.01 Pulse Width=300mS 1% Duty Cycle 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 35 8.3ms Single Half Sine-Wave (JEDED Method) 30 25 20 15 10 5 0 1.8 1 2 INSTANTANEOUS FORWARD VOLTAGE, (V) 5 10 100 60 40 20 EDB101~E 10 EDB105~EDB106 DB104 6 4 1 TJ = 25 OC 0.1 0.2 50 100 FIG.5 MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 200 2 20 NUMBER OF CYCLES AT 60Hz FIG.4 TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS JUNCTION CAPACITANCE, (pF) INSTANTANEOUS FORWARD CURRENT, (A) RATING AND CHARACTERISTICS CURVES ( EDB101 THRU EDB106 ) 0.4 1.0 2 4 10 20 40 REVERSE VOLTAGE, (V) FIG.6 TYPICAL JUNCTION CAPACITANCE 100 DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.