Hynix H5RS5223CFR-14L 512mbit (16mx32) gddr3 sdram Datasheet

H5RS5223CFR
512Mbit (16Mx32) GDDR3 SDRAM
H5RS5223CFR
This document is a general product description and is subject to change without notice. Hynix Semiconductor does not assume any
responsibility for use of circuits described. No patent licenses are implied.
Rev. 1.5 /Jul. 2008
1
H5RS5223CFR
Revision History
Revision
Page
History
Date
Remark
0.1
Defined target spec.
Oct. 2007
Preliminary
0.2
Changed tCK_max to 2ns at (-N0) & PKG drawing value
Oct. 2007
Preliminary
0.3
1. Revised the slew rate from 6V/ns to 3V/ns on page 54.
2. Inserted the code ‘C’ in Part number, that means ‘normal power
and commercial temperature’.
Nov. 2007
Preliminary
0.4
Inserted 1.2Ghz speed bin
Dec. 2007
Preliminary
1.0
Added IDD Values
Jan. 2008
1.1
47
Changed IDDO/IDD1/IDD5A Values
Jan. 2008
1.2
43
Inserted the thermal characteristics table (Table 12)
Mar. 2008
1.3
44
Inserted the note for IO reference voltage (VREF)
May. 2008
1.4
44
Inserted the note (VDD/VDDQ)
Jun. 2008
1.5
3
48
51-52
55
1.
2.
3.
4.
Jul. 2008
Rev.1.5 / Jul. 2008
Inserted
Inserted
Inserted
Inserted
1.3Ghz speed bin (-N3C)
IDD Values for 1.3Ghz
AC Parameter Values for 1.3Ghz
Eletrical Characteristics Usage Values for 1.3Ghz
2
H5RS5223CFR
DESCRIPTION
The Hynix H5RS5223 is a high-speed CMOS, dynamic random-access memory containing 536,870,912 bits.
The Hynix H5RS5223 is internally configured as a eight-bank DRAM.
The Hynix H5RS5223 uses a double data rate architecture to achieve high-speed opreration. The double date rate architecture is
essentially a 4n-prefetch architecture, with an interface designed to transfer two data words per clock cycle at the I/O pins. A single
read or write access for the Hynix H5RS5223 consists of a 4n-bit wide, every two-clock-cycles data transfer at the internal DRAM core
and two corresponding n-bit wide, one-half-clock-cycle data transfers at the I/O pins. Read and write accesses to the Hynix
H5RS5223 is burst oriented; accesses start at a selected locations and continue for a programmed number of locations in a programmed sequence. Accesses begin with the registration of an ACTIVE command, which is then followed by a READ of WRITE command. The address bits registered coincident with the ACTIVE command are used to select the bank and row to be accessed
(BA0,BA1, BA2 select the bank; A0-A11 select the row). The address bits registered coincident with the READ or WRITE command
are used to select the starting column location for the burst access. Prior to normal operation, the Hynix H5RS5223 must be initialized.
FEATURES
•
2.05V/ 1.8V/ 1.5V power supply supports
•
CAS Latency: 4~11 (clock)
(For more detail, Please see the Table 12 on page 43)
•
Data mask (DM) for masking WRITE data
•
Single ended READ Strobe (RDQS) per byte
•
4n prefetch
•
Single ended WRITE Strobe (WDQS) per byte
•
Programmable burst lengths: 4, 8
•
Internal, pipelined double-data-rate (DDR) architecture;
•
32ms, 8K-cycle auto refresh
two data accesses per clock cycle
•
Auto precharge option
•
On Die Termination
•
Auto Refresh and Self Refresh Modes
•
Output Driver Strength adjustment by EMRS
•
1.8V Pseudo Open Drain I/O
•
Calibrated output driver
•
Concurrent Auto Precharge support
•
Differential clock inputs (CK and CK#)
•
tRAS lockout support, Active Termination support
•
Commands entered on each positive CK edge
•
Programmable Write latency(1, 2, 3, 4, 5, 6)
RDQS edge-aligned with data for READ; with WDQS
•
Boundary Scan Function with SEN pin
center-aligned with data for WRITE
•
Mirror Function with MF pin
•
•
8 internal banks for concurrent operation
ORDERING INFORMATION
Part No.
Power Supply
Clock Frequency
Max Data Rate
1300MHz
2600Mbps/pin
1200MHz
2400Mbps/pin
H5RS5223CFR-N0C
1000MHz
2000Mbps/pin
H5RS5223CFR-11C
900MHz
1800Mbps/pin
700MHz
1400Mbps/pin
500MHz
1000Mbps/pin
700MHz
1400Mbps/pin
550MHz
1100Mbps/pin
H5RS5223CFR-N3C
H5RS5223CFR-N2C
H5RS5223CFR-14C
VDD/VDDQ=2.05V
VDD/VDDQ=1.8V
H5RS5223CFR-20C
H5RS5223CFR-14L
H5RS5223CFR-18C
VDD/VDDQ=1.5V
Interface
Package
POD_18
10mmx14mm
136Ball FBGA
POD_15
Note) Above Hynix P/N’s and their homogeneous Subcomponents are RoHS (& Lead free) compliant
Rev.1.5 / Jul. 2008
3
H5RS5223CFR
BALLOUT CONFIGURATION
1
2
3
4
9
10
11
12
A
VDDQ
VDD
VSS
ZQ
MF
VSS
VDD
VDDQ
B
VSSQ
DQ0
DQ1
VSSQ
VSSQ
DQ9
DQ8
VSSQ
C
VDDQ
DQ2
DQ3
VDDQ
VDDQ
DQ11
DQ10
VDDQ
D
VSSQ W DQS0 RDQS0 VSSQ
VSSQ RDQS1 W DQS1 VSSQ
E
VDDQ
DQ4
DM0
VDDQ
VDDQ
DM1
DQ12
VDDQ
F
VDD
DQ6
DQ5
CAS#
CS#
DQ13
DQ14
VDD
G
VSS
VSSQ
DQ7
BA0
BA1
DQ15
VSSQ
VSS
H
VREF
A1
RAS#
CKE
W E#
BA2
A5
VREF
J
VSS
NC
RFU
VDDQ
VDDQ
CK#
CK
VSS
K
VDD
A10
A2
A0
A4
A6
A8/AP
VDD
L
VSS
VSSQ
DQ25
A11
A7
DQ17
VSSQ
VSS
M
VDD
DQ24
DQ27
A3
A9
DQ19
DQ16
VDD
N
VDDQ
DQ26
DM3
VDDQ
VDDQ
DM2
DQ18
VDDQ
P
VSSQ W DQS3 RDQS3 VSSQ
VSSQ RDQS2 W DQS2 VSSQ
R
VDDQ
DQ28
DQ29 VDDQ
VDDQ
DQ21
DQ20
VDDQ
T
VSSQ
DQ30
DQ31 VSSQ
VSSQ
DQ23
DQ22
VSSQ
U
VDDQ
VDD
VSS
RES
VSS
VDD
VDDQ
SEN
5
6
7
8
16M x 32
Rev.1.5 / Jul. 2008
Configuration
2M x 32 x 8 banks
Refresh Count
8k
Bank Address
BA0 - BA2
Row Address
A0~A11
Column Address
A0~A7, A9
AP Flag
A8
4
H5RS5223CFR
FUNCTIONAL BLOCK DIAGRAM
8Banks x 2Mbit x 32 I/O double Data Rate Synchronous DRAM
CKE
CK
CK#
CONTROL
LOGIC
COMMAND
DECODE
CS#
RAS#
CAS#
WE#
REFRESH
COUNTER 12
MODE REGISTERS
ROW
ADDRESS
MUX
15
12
12
BANK7
BANK6
BANK5
BANK4
BANK3
BANK0
BANK2
BANK1ROW
ADDRESS
LATCH
BANK0 &
ROW DECODER
ADDRESS
40%
LATCH
&
DECODER
BANK7
BANK6
BANK5
BANK4
BANK3
BANK2
BANK1BANK0
MEMORY
ARRAY
(4096x512x128)
BANK0
MEMORY
ARRAY
(4096x512x128)
SENSE AMPLIFIERS
CK/ CK#
CCL0, CCL1
DLL
32
128
READ
LATCH
32
32
32
MUX
DRVRS
DATA
32
DQ0~DQ31
SENSE AMPLIFIERS
66,536
A0~A11
BA0- BA2
15
I/O GATING
DM MASK LOGIC
128
BANK
CONTROL
LOGIC
ADDRESS
REGISTER
512
(x128)
128
WRITE
FIFO
&
DRIVERS
MASK
COLUMN
DECODER
CK/CK#
COLUMN
ADDRESS
COUNTER
LATCH
7
CK OUT
CK IN
2
COL0, COL1
Rev.1.5 / Jul. 2008
4
4
4
4
4
4
4
4
32
32
32
32
32
32
32
32
128
DATA
WDQS(0~3)
4
16
3
9
CK/CK#
INPUT
REGISTERS
3
RCVRS
DM(0~3)
32
4
5
H5RS5223CFR
BALLOUT DESCRIPTIONS
FBGA BALLOUT
SYMBOL
TYPE
DESCRIPTION
J10, J11
CK, CK#
Input
Clock: CK and CK# are differential clock inputs. All address and control input signals are sampled on the crossing of the positive edge of
CK and negative edge of CK#.
Input
Clock Enable: CKE HIGH activates and CKE LOW deactivates the internal clock, input buffers and output drivers. Taking CKE LOW provides
PRECHARGE POWER-DOWN and SELF REFRESH operations(all banks
idle), or ACTIVE POWER-DOWN (row ACTIVE in any bank). CKE is
synchronous for POWER-DOWN entry and exit, and for SELF REFRESH
entry. CKE is asynchronous for SELF REFRESH exit and for disabling
the outputs. CKE must be maintained HIGH throughout read and write
accesses. Input buffers (excluding CK, CK# and CKE) are disabled
during POWER-DOWN. Input buffers (excluding CKE) are disabled
during SELF REFRESH.
H4
CKE
F9
CS#
Input
Chip Select: CS# enables (registered LOW)and disables (registered
HIGH) the command decoder. All commands are masked when CS# is
registered HIGH. CS# provides for external bank selection on systems
with multiple banks. CS# is considered part of the command code.
H3, F4, H9
RAS#, CAS#, WE#
Input
Command Inputs: RAS#, CAS# and WE#(along with CS#) define the
command being entered.
E(3, 10), N(3, 10)
DM0-DM3
Input
Input Data Mask: DM is an input mask signal for write data. Input
data is masked when DM is sampled HIGH along with that input data
during a WRITE access. DM is sampled on rising and falling edges of
WDQS.
G(4, 9), H10
BA0 - BA2
Input
Bank Address Inputs: BA0 and BA2 define to which bank an ACTIVE,
READ, WRITE or PRECHARGE command is being applied.
Address Inputs: Provide the row address for ACTIVE commands, and
the column address and auto precharge bit(A8) for READ/WRITE
commands, to select one location out of the memory array in the
respective bank. A8 sampled during a PRECHARGE command determines whether the PRECHARGE applies to one bank (A8 LOW, bank
selected by BA0 - BA2 ) or all banks (A8 HIGH). The address inputs
also provide the op-code during a MODE REGISTER SET command.
BA0 and BA1 define which mode register (mode register or extended
mode register) is loaded during the LOAD MODE REGISTER command.
H(2, 11),
K(2-4, 9-11),
L(4, 9), M(4, 9)
A0-A11
Input
B(2, 3), C(2, 3), E2, F(2, 3),
G3,B(10, 11), C(10, 11),
E11, F(10, 11), G10, L10,
M(10, 11), N11, R(10, 11),
T(10,11), L3, M(2, 3),
N2,R(2, 3), T(2, 3)
DQ0-31
I/O
D(3, 10), P(3, 10)
RDQS0-3
Output
READ Data Strobe: Output with read data. RDQS is edge-aligned with
read data.
D(2, 11), P(2, 11)
WDQS0-3
Input
WRITE Data strobe: Input with write data. WDQS is center aligned to
the input data.
U4
SEN
Input
Scan Enable Pin. Logic High would enable Scan Mode. Should be tied
to GND when not in use. This pin is a CMOS input.
J(2, 3)
NC/RFU
Rev.1.5 / Jul. 2008
Data Input/Output:
No Connect
6
H5RS5223CFR
BALLOUT DESCRIPTIONS
-CONTINUE
FBGA Ball Out
SYMBOL
TYPE
DESCRIPTION
A(1, 12), C(1, 4, 9, 12),
J(4, 9), N(1, 4, 9, 12),
R(1, 4, 9, 12), U(1, 12)
VDDQ
Supply
B(1, 4, 9, 12), D(1, 4, 9, 12), G(2, 11),
L(2, 11), P(1, 4, 9, 12), T(1, 4, 9, 12)
VSSQ
Supply
A(2, 11), F(1, 12),
M(1, 12), U(2, 11) K(1, 12)
VDD
Supply
Power Supply: +1.8V.
A(3, 10), G(1, 12),
L(1, 12), U(3, 10) J(1, 12)
VSS
Supply
Ground
H(1, 12)
VREF
Supply
Reference voltage.
A9
MF
Reference
Mirror Function for clamshell mounting of DRAMs
A4
ZQ
Reference
External Reference Pin for autocalibration.
It should be connected to RQ(=240Ω)
U9
RES
Reference
Reset Pin. The RES pin is a VDD CMOS input.
DQ Power Supply: +1.8V.
Isolated on the die for improved noise immunity.
DQ Ground: Isolated on the die for improved noise immunity.
Mirror Function
The GDDR3 SDRAM provides a mirror function(MF) ball to change the physical location of the control lines and all address lines,
assisting in routing devices back to back. The MF ball will affect RAS#, CAS#, WE#, CS# and CKE on balls H3, F4, H9, F9 and H4
respectively and A0, A1, A2, A3, A4, A5, A6, A7, A8, A9, A10, A11, BA0, BA1 and BA2 on balls K4, H2, K3, M4, K9, H11, K10, L9, K11,
M9, K2, L4, G4, G9 and H10 respectively and only detects a DC input. The MF ball should be tied directly to VSS of VDD depending on
the control line orientation desired.
When MF ball is tied low the ball orientation is as follows. RAS#-H3, CAS#-F4, WE#-H9, CS#-F9, CKE-H4, A0-K4, A1-H2, A2-K3, A3M4, A4-K9, A5-H11, A6-K10, A7-L9, A8-K11, A9-M9, A10-K2, A11-L4, BA0-G4, BA1-G9 and BA2-H10. The high condition on the MF
ball will change the location of the control balls as follows; CS#-F4, cas#-F9, ras#-H10, WE#-H4, CKE-H9, A0-K9, A1-H11, A2-K10,
A3-M9, A4-K4, A5-H2, A6-K3, A7-L4, A8-K2, A9-M4, A10-K11, A11-L9, BA0-G9, BA1-G4 and BA2-H3. This Mirror Fuction does not
work under Boundary Scan Test condition.
Mirror Function Signal Mapping
PIN
RAS#
CAS#
WE#
CS#
CKE
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
BA0
BA1
BA2
Rev.1.5 / Jul. 2008
MF LOGIC STATE
HIGH
LOW
H10
F9
H4
F4
H9
K9
H11
K10
M9
K4
H2
K3
L4
K2
M4
K11
L9
G9
G4
H3
H3
F4
H9
F9
H4
K4
H2
K3
M4
K9
H11
K10
L9
K11
M9
K2
L4
G4
G9
H10
7
H5RS5223CFR
GDDR3 Initialization and Power Up
GDDR3 SDRAMs must be powered up and initialized in a predefined manner. Operational procedures other
than those specified may result in undefined operation. Power must be first applied to VDD and VDDQ simultaneously or VDD first
and VDDQ later, and then to VREF. VREF can be applied any time after VDDQ. Once power has been applied and the clocks are stable
the GDDR3 device requires 200us before the RES pin transitions to high. Upon power-up and after the clock is stable, the on-die termination value for the address and control pins will be set, based on the state of CKE when the RES pin transitions from LOW to
HIGH. On the rising edge of RES, the CKE pin is latched to determine the on die termination value for the address and control lines.
If CKE is sampled at a logic LOW then the on die termination will be set to 1/2 of ZQ and, if CKE is sampled logic HIGH then the on
die termination will be set to the same value as ZQ. CKE must meet tATS and tATH on the rising of RES to set the on die termination
for address and control lines. Once tATH is met, set CKE to HIGH. An additional 200us is required for the address and command on
die terminations to calibrate and update.
RES must be maintained at a logic LOW-level value and CS# must be maintained HIGH, during the first stage of power-up to ensure
that the DQ outputs will be in a High-Z state(un-terminated).
After the RES pin transitions from LOW to HIGH, wait until a 200us delay is satisfied. Issue DESELECT on the command bus during
this time. Issue a PRECHARGE ALL command. Next a LOAD MODE REGISTER command must be issued for the extended mode register (BA1 LOW and BA0 HIGH) to activate the DLL and set operating parameters, followed by the LOAD MODE REGISTER command
(BA0/BA1 both LOW) to reset the DLL and to program the rest of the operating parameters. 5k clock cycles are required between the
DLL reset and any READ command to allow the DLL to lock. A PRECHARGE ALL command should then be applied, placing the device
in the all banks idle state.
Once in the idle state, two AUTO REFRESH cycles must be issued. Following these requirements, the GDDR3 SDRAM is ready for normal operation.
VDD
VDDQ
VREF
T0
CK#
T1
Ta0
PRE
LMR
Tb0
Tc0
Td0
Te0
Tfo
PRE
AR
AR
ACT
CK
tCH
RESET
ATS
tCL
ATH
CKE
COMMAND
NOP
LMR
DM
tIS tIH
CODE
ALL BANKS
A0A7,A9A11,A8
tIS
CODE
tIH
CODE
tIS
tIH
RA
ALL BANKS
CODE
RA
tIS tIH
tIS tIH
BA0,BA
1
RA
RDQS
BAO=L,
BA1=H
BAO=H,
BA1=L
HIGH
HIGH
WDQS
HIGH
DQ
T=100us
T=10us
Power-up:VDD and
Clock stable
T=200us
Precharge All
Banks
tRP
tMRD
tMRD
tRP
Load Mode Resistor Precharge All
Banks
DLL Reset
Rev.1.5 / Jul. 2008
tRFC
tRFC
Load Extended
Mode Resistor
1st Auto
Refresh
2nd Auto
Refresh
8
H5RS5223CFR
ODT Updating
The GDDR3 SDRAM uses programmable impedance output buffers. This allows a user to match the driver impedance to the system.
To adjust the impedance, an external precision resistor (RQ) is connected between the ZQ pin and VSSQ. The value of the resistor
must be six times the desired driver impedance. For example, a 240Ω. resistor is required for an output impedance of 40Ω. To ensure
that output impedance is one-sixth the value of RQ (within 10 percent), RQ should be in the range of 210Ω. to 270Ω. (30Ω. - 50Ω.
output impedance).
CK and CK# are not internally terminated. CK and CK# will be terminated on the system module using external 1% resistors.
The output impedance and on die termination is updated during every AUTO REFRRESH commands to compensate for variations in
supply voltage and temperature. The output impedance updates are transparent to the system. Impedance updates do not affect
device operation, and all datasheet timings and current specifications are met during an update.
A maximum of eight AUTO REFRESH commands can be posted to any given GDDR3 SDRAM, meaning that the maximum absolute
interval between any AUTO REFRESH command and the next AUTO REFRESH command is 8 x 3.9us (31.2us). This maximum absolute interval guarantees that the output drivers and the on die terminations of GDDR3 SDRAMs are recalibrated often enough to keep
the impedance characteristics of those within the specified boundaries.
ODT Control
Bus snooping for READ commands other than CS# is used to control the on die termination in the dual load configuration. The
GDDR3 SGRAM will disable the DQ and RDQS on die termination when a READ command is detected regardless of the state of CS#.
The on die termination is disabled x clocks after the READ command where x equals CL-1 and stay off for a duration of BL/2+2CK. In
a two-rank system, both DRAM devices snoop the bus for READ commands to either device and both will disable the on die termination, for the DQ and DQS pins if a READ command is detected. The on die termination for all other pins on the device is always
turned-on for both a single-rank system and a dual-rank system unless it is turned off in the EMRS. Only DQ,WDQS and DM pins can
turn off through the EMRS.
Rev.1.5 / Jul. 2008
9
H5RS5223CFR
Mode Register Definition
The mode register is used to define the specific mode of operation of the GDDR3 SDRAM. This definition includes the selection of a
burst length, CAS latency, WRITE latency, and operating mode, as shown in Figure 3, Mode Register Definition, on page 11. The
mode register is programmed via the MODE REGISTER SET command (with BA0=0, BA1=0 and BA2=0) and will retain the stored
information until it is programmed again or the device loses power (except for bit A8, which is self-clearing). Re-programming the
mode register will not alter the contents of the memory. The mode register must be loaded (reloaded) when all banks are idle and no
bursts are in progress, and the controller must wait the specified time before initiating any subsequent operation. Violating either of
these requirements will result in unspecified operation.
Mode register bits A2-A0 specify the burst length; A3 specifies the type of burst (sequential); A4-A6 specify the CAS latency; A7 is a
test mode; A8 specifies the operating mode; and A9-A11 specifiy the WRITE latency.
Rev.1.5 / Jul. 2008
10
H5RS5223CFR
Figure 3: Mode Register Definition
BA1
BA0
0
0
A11
A10
A9
WL
A8
A7
DR
TM
A6
A5
A4
CAS Latency
A3
A2
A1
BT
CL
Burst Length
A8
DLL Reset
A3
Burst Type
0
No
0
Sequential
1
Yes
1
Reserved
A11
A10
A9
WRITE Latency
0
0
0
Reserved
0
0
1
1
0
1
0
2
0
1
1
3
1
0
0
4
1
0
1
5
1
1
0
6
1
1
1
Reserved
Note:
A0
A1
A0
Burst Length
A7
Test Mode
0
0
Reserved
0
Normal
0
1
Reserved
1
Yes
1
0
4
1
1
8
A2
A6
A5
A4
CAS Latency
0
0
0
0
8
0
0
0
1
9
0
0
1
0
10
0
0
1
1
11
0
1
0
0
4
0
1
0
1
5
0
1
1
0
6
0
1
1
1
7
1
0
0
0
Reserved
1
0
0
1
Reserved
1
0
1
0
Reserved
1
0
1
1
Reserved
1
1
0
0
Reserved
1
1
0
1
Reserved
1
1
1
0
Reserved
1
1
1
1
Reserved
1) The DLL reset command is self-clearing.
Rev.1.5 / Jul. 2008
11
H5RS5223CFR
Burst Length
Read and write accesses to the GDDR3 SDRAM are burst-oriented, with the burst length being programmable, as shown in Figure3,
Mode Register Definition. The burst length determines the maximum number of column locations that can be accessed for a given
READ or WRITE command. Burst lengths of 4 or 8 locations are available for the sequential burst type. Reserved states should not be
used, as unknown operation or incompatibility with future versions may result. When a READ or WRITE command is issued, a block
of columns equal to the burst length is effectively selected. All accesses for that burst take place within this block, meaning that the
burst will wrap within the block if a boundary is reached. The block is uniquely selected by A2. Ai when the burst length is set to four
and by A3. Ai when the burst length is set to eight(where Ai is the most significant column address bit for a given configuration). The
remaining(least significant) address bit(s) is (are) used to select the starting location within the block. The programmed burst length
applies to both read and write bursts.
Burst Type
Accesses within a given burst must be programmed to be sequential; this is referred to as the burst type and is selected via bit A3.
This device does not support the interleaved burst mode found in DDR SDRAM devices. The ordering of accesses within a burst is
determined by the burst length, the burst type, and the starting column address, as shown in Table3.
Table 3: Burst Definition
Burst1, 2
Length
Starting Column Address
Type=Sequential
A1
A0
0
0
A2
A1
A0
0
0
0
0-1-2-3-4-5-6-7
1
0
0
4-5-6-7-0-1-2-3
4
8
Order of Accesses
Within a Burst
0-1-2-3
NOTE:
1. For a burst length of four, A2-A7 select the block of four burst; A0-A1 select the starting column within the block and must be set
to zero.
2. For a burst length of eight, A3-A7 select the of eight burst; A0-A2 select the starting column within the block.
Rev.1.5 / Jul. 2008
12
H5RS5223CFR
CAS Latency
The CAS latency is the delay, in clock cycles, between the registration of a READ command and the availability of the first bit of output data. The latency can be set to 7-11 clocks, as shown in Figure 4, CAS Latency, on page 13. If a READ command is registered at
clock edge n, and the latency is m clocks, the data will be available nominally coincident with clock edge n + m. Table4 indicates the
operating frequencies at which each CAS latency setting can be used. For the proper operation, do not change the CL without DLL
reset. Or proper CL should be set with DLL reset code
Reserved states should not be used as unknown operation or incompatibility with future versions may result.
Table 4: CAS Latency
ALLOWABLE OPERATING FREQUENCY (MHz)
SPEED
CL=11
-N3
<=1300
-N2
<=1200
-N0
<=1000
-11
-14(L)
CL=10
CL=9
CL=7
<=900
<=700
-18
<=550
-20
<=500
Figure 4: CAS Latency
Rev.1.5 / Jul. 2008
13
H5RS5223CFR
Write Latency
The WRITE latency (WL) is the delay, in clock cycles,between the registration of a WRITE command and the availability of the first
bit of input data as shown in Figure5. The latency can be set from 1 to 6 clocks depending on the operating frequency and desired
current draw. When the write latencies are set to 1 or 4 clocks, the input receivers never turn off, in turn, raising the operating power.
When the WRITE latency is set to 5 or 6 clocks the input receivers turn on when the WRITE command is registered. If a WRITE command is registered at clock edge n, and the latency is m clocks, the data will be available nominally coincident with clock edge n + m.
Reserved states should not be used as unknown operation or incompatibility with future versions may result.
Figure 5: WRITE Latency
Test Mode
The normal operating mode is selected by issuing a MODE REGISTER SET command with bit A7 set to zero, and bits A0~A6 and
A8~A11 set to the desired values. Test Mode is initiated by issuing a MODE REGISTER SET command with bit A7 set to one, and bits
A0~A6 and A8~A11 set to the desired values. Test mode funtions are specific to each DRAM vendor and their exact function are hidden from the user.
DLL Reset
The normal operating mode is selected by issuing a MODE REGISTER SET command with bit A8 set to zero, and bits A0~A7 and
A9~A11 set to the desired values. A DLL reset is initiated by issuing a MODE REGISTER SET command with bit A8 set to one, and bits
A0~A7 and A9~A11 set to the desired values. When a DLL Reset is complete the GDDR3 SDRAM Reset bit, A8 of the mode register
is self clearing (i.e.automatically set to a zero by the DRAM). Test modes and reserved states should not be used because unknown
operation or incompatibility with future versions may result.
Rev.1.5 / Jul. 2008
14
H5RS5223CFR
Extended Mode Register
The extended mode register controls functions beyond those controlled by the mode register; these additional functions are DLL
enable/disable, drive strength, data termination, vendor ID. These functions are controlled via the bits shown in Figure 6, Extended
Mode Register Definition. The extended mode register is programmed via the LOAD MODE REGISTER command to the mode register
(with BA0 = 1, BA1 = 0 and BA2=0) and will retain the stored information until it is programmed again or the device loses power. The
enabling of the DLL should always be followed by a LOAD MODE REGISTER command to the mode register (BA0/BA1 both low) to
reset the DLL.The extended mode register must be loaded when all banks are idle and no bursts are in progress, and the controller
must wait the specified time before initiating any subsequent operation. Violating either of these requirements could result in unspecified operation.
Figure 6: Extended Mode Register Definition
BA1
BA0
A11
A10
A9
A8
A7
A6
0
1
Term
VID
Ron
0
tWR
DLL
A5
A4
A3
tWR
Ron
0
1
40
60
A10
Vendor ID
0
1
Off
On
A11
C/A Termination
0
1
Default
Half of default
A6
DLL enable
0
1
Enable
Disable
A7
A5
A4
tWR
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
12
14
5
6
7
8
9
10
A1
DT
Ron of Pull-up
A9
A2
A0
DZ
A1
A0
Drive Strength
0
0
1
1
0
1
0
1
Auto Cal
30
40
50(48)
A3
A2
Data Termination
0
0
1
1
0
1
0
1
DT disabled
RES
1/4 RQ
1/2 RQ
NOTE:
1. The DT disable function disables all pins.
2. The default setting at Power Up for A3,A2 is 10 or 11
3. If the user activates bits in the extended mode register in an optional field, device will work improperly.
4. The optional values of the drive strength (A1,A0) are only targets and can be determined by the DRAM vendor.
5. WR_A (write recovery time for autoprecharge) in clock cycles is calculated by dividing tWR (in nS) and rounding up to the next
integer (WR[cycles] = tWR(ns)/tCK(ns)). The mode register must be programmed to this value.
6. Default value in C/A Termination is determined by CKE status at the rising edge of RESET during power-up.
Rev.1.5 / Jul. 2008
15
H5RS5223CFR
DLL Enable/Disable
The DLL must be enabled for normal operation. DLL enable is required during power-up initialization and upon returning to normal
operation after disabling the DLL for debugging or evaluation. (When the device exits self refresh mode, the DLL is enabled automatically.) Any time the DLL is enabled, 5K clock cycles must occur before a READ command can be issued.
tWR(WR_A)
The value of tWR in the AC parametrics table on page 49 of this specification is loaded into register bits 5 and 4. The WR_A (write
recovery time for autoprecharge) in clock cycles is calculated by dividing tWR (in ns) and rounding up to the next integer (WR[cycles]
= tWR(ns)/tCK(ns)). The mode register must be programmed to this value.
Data Termination
The data termination value is used to define the value for the on die termination for the DQ, DM, and WDQS pins. The GDDR3 device
supports one-quarter ZQ and one-half ZQ termination for a nominal 60Ω or 120Ω set with bit A3 and A2 during an EMRS command
for a single- or dual-loaded system.
Data Driver Impedance
The Data Driver Impedance, DZ, is used to determine the value of the data drivers impedance. When auto calibration is used the
data driver impedance is set to 1/6 ZQ and it’s tolerance is determined by the calibration accuracy of the device. When any other
value is selected the target impedance is set nominally to the selected impedance. However, the accuracy is now determined by the
device’s specific process corner, applied voltage and operating temperature.
Rev.1.5 / Jul. 2008
16
H5RS5223CFR
Manufacturers Vendor Code Identification
Table 5: Vendor IDs
VENDOR
DQ(3:0)
The Manufacturers Vendor Code, V, is selected by issuing an
Reserved
0
EXTENDED MODE REGISTER SET command with bits A10 set to
Samsung
1
1, and bits A0-A9 and A11 set to the desired values. When the V
Infineon
2
Elpida
3
Etron
4
Nanya
5
Hynix
6
Mosel
7
Winbond
8
ESMT
9
Reserved
A
Reserved
B
Reserved
C
Reserved
D
Reserved
E
Micron
F
function is enabled the GDDR3 SDRAM will provide its manufacturers vendor code on DQ[3:0] and revision identification on
DQ[7:4]. The code will be driven onto the DQ bus after tIDON
with respect to the EMRS that set A10 to 1. The DQ bus will be
continuously driven until an EMRS write sets A10 back to 0. The
DQ bus will be in a Hi-Z state after tIDOFF. The code can be
sampled by the controller after waiting tIDON max and before
tIDOFF min.
Rev.1.5 / Jul. 2008
17
H5RS5223CFR
Clock frequency change sequence during the device operation
Not only Clock frequency but also VDD change sequence as below
Both existing tCK and desired tCK are in DLL-On mode
- Change frequency from existing frequency to desired frequency
- Issue Precharge All Banks command
- Issue MRS command to reset the DLL while other fields are valid and required 5K tCK to lock the DLL
- Issue Precharge All Banks command. Issue at least Auto-Refresh command
CK#
CK
COMMAND NOP
NOP
NOP
NOP
NOP
NOP
PRE
MRS
PRE
NOP
AR
NOP
All Banks
All Banks
DLL
Precharg
Precharg
Reset
e
e
tRP
tMRD
Frequency
Change
tFCHG
5tCK (DLL locking time)
Existing tCK is in DLL-on mode while desired tCK is in DLL-off mode
-
Issue Precharge All Banks command
Issue EMRS command to disable the DLL
Issue Precharge All Banks command
Change the frequency from existing to desired.
Issue Auto-Refresh command at least two. Issue MRS command
CK#
CK
COMMAND PRE
EMRS
PRE
NOP
All Banks
All Banks
DLL
Precharg
Precharg
OFF
e
e
tRP
tMRD
NOP
NOP
AR
MRS
NOP
NOP
NOP
NOP
NOP
AR
Frequency
Change
tFCHG
Clock frequency change in case existing tCK is in DLL-off mode while desired tCK is in DLL-on mode
- Issue Precharge All Banks command and issue EMRS command to disable the DLL.
- Issue Precharge All Banks command.
- Change the clock frequency from existing to desired
- Issue Precharge All Banks command.
- Issue EMRS command to enable the DLL
- Issue MRS command to reset the DLL and required 5K tCK to lock the DLL.
- Issue Precharge All Banks command.
- Issue Auto-Refresh command at least two
CK#
CK
COMMAND PRE
EMRS
PRE
All Banks
All Banks
DLL
Precharg
Precharg
OFF
e
e
tRP
tMRD
NOP
NOP
Frequency
Change
tFCHG
NOP
PRE
All Banks
Precharg
e
tRP
EMRS
MRS
DLL
On
DLL
Reset
tMRD
PRE
All Banks
Precharg
e
tMRD
5tCK (DLL locking time)
Rev.1.5 / Jul. 2008
18
H5RS5223CFR
Commands
Table6 provides a quick reference of available commands, followed by a description of each command. Two additional truth tables
appear following the Operation section; these tables provide current state/next state information.
Table 6: Truth Table - Commands
Note: 1
NAME (FUNCTION)
CS#
RAS#
CAS#
WE#
ADDR
NOTES
DESELECT (NOP)
H
X
X
X
X
8
NO OPERATION (NOP)
L
H
H
H
X
8
ACTIVE (Select bank and activate row)
L
L
H
H
Bank/Row
3
READ (Select bank and column, and start READ burst)
L
H
L
H
Bank/Col
4
WRITE (Select bank and column, and start WRITE burst)
L
H
L
L
Bank/Col
4
PRECHARGE (Deactivate row in bank or banks)
L
L
H
L
Code
5
AUTO REFRESH or SELF REFRESH
(Enter self refresh mode)
L
L
L
H
X
6, 7
LOAD MODE REGISTER
L
L
L
L
Op-Code
2
DATA TERMINATOR DISABLE
X
H
L
H
X
10
Table 7: Truth Table 2 - DM Operation
NAME (FUNCTION)
DM
DQS
NOTES
Write Enable
L
Valid
9
Write Inhibit
H
X
8
NOTE:
1. CKE is HIGH for all commands shown except SELF REFRESH.
2. BA0-BA1 select either the mode register or the extended mode register (BA0 = 0, BA1 = 0 select the mode register;
BA0 = 1, BA1 = 0 select extended mode register; other combinations of BA0.BA1 are reserved). A0-A11 provide the opcode to be
written to the selected mode register.
3. BA0-BA2 provide bank address and A0-A11 provide row address.
4. BA0-BA2 provide bank address; A0-A7 and A9 provide column address; A8 HIGH enables the auto precharge feature
(non-persistent), and A8 LOW disables the auto precharge feature.
5. A8 LOW: BA0-BA2 determine which bank is precharged. A8 HIGH: all banks are precharged and BA0-BA2 are “Don’t Care.”
6. This command is AUTO REFRESH if CKE is HIGH, SELF REFRESH if CKE is LOW.
7. Internal refresh counter controls row addressing; all inputs and I/Os are Don’t Care except for CKE.
8. DESELECT and NOP are functionally interchangeable.
9. Used to mask write data; provided coincident with the corresponding data.
10. Used for bus snooping when the DQ termination is set to 120 ohms in the EMR and cannot be used during power-down or self
refresh.
Rev.1.5 / Jul. 2008
19
H5RS5223CFR
Deselect
The DESELECT function (CS# HIGH) prevents new commands from being executed by the GDDR3 SDRAM. The GDDR3 SDRAM is
effectively deselected. Operations already in progress are not affected.
NO Operation (NOP)
The NO OPERATION (NOP) command is used to instruct the selected GDDR3 SDRAM to perform a NOP(CS# LOW). This prevents
unwanted commands from being registered during idle or wait states. Operations already in progress are not affected.
LOAD MODE REGISTER
The mode registers are loaded via inputs A0~A11. See mode register descriptions in the Register Definition section. The LOAD
MODE REGISTER command can only be issued when all banks are idle, and a subsequent executable command cannot be issued
until tMRD is met.
ACTIVE
The ACTIVE command is used to open (or activate) a row in a particular bank for a subsequent access. The value on the BA0~BA2
inputs selects the bank, and the address provided on inputs A0~A11 selects the row. This row remains active (or open) for accesses
until a precharge command is issued to that bank. A precharge command must be issued before opening a different row in the same
bank.
READ
The READ command is used to initiate a burst read access to an active row. The value on the BA0~BA2 inputs selects the bank, and
the address provided on inputs A0~A7, A9 selects the starting column location. The value on input A8 determines whether or not
auto precharge is used. If auto precharge is selected, the row being accessed will be precharged at the end of the read burst; if auto
precharge is not selected, the row will remain open for subsequent accesses.
WRITE
The WRITE command is used to initiate a burst write access to an active row. The value on the BA0~BA2 inputs selects the bank,
and the address provided on inputs A0~A7, A9 selects the starting column location. The value on input A8 determines whether or not
auto precharge is used. If auto precharge is selected, the row being accessed will be precharged at the end of the write burst; if auto
precharge is not selected, the row will remain open for subsequent accesses. Input data appearing on the DQs is written to the memory array subject to the DM input logic level appearing coincident with the data. If a given DM signal is registered LOW, the corresponding data will be written to memory; if the DM signal is registered HIGH, the corresponding data inputs will be ignored and a
write will not be executed to that byte/column location.
PRECHARGE
The PRECHARGE command is used to deactivate the open row in a particular bank or the open row in all banks. The bank(s) will be
available for a subsequent row access a specified time (tRP) after the precharge command is issued. Input A8 determines whether
one or all banks are to be precharged, and in the case where only one bank is to be precharged, inputs BA0.BA2 select the bank.
Otherwise, BA0. BA2 are treated as ”Don’t Care.” Once a bank has been precharged, it is in the idle state and must be activated prior
to any READ or WRITE commands being issued to that bank.
A PRECHARGE command will be treated as a NOP if there is no open row in that bank (idle state) or if the previously open row is
already in the process of precharging.
Rev.1.5 / Jul. 2008
20
H5RS5223CFR
Auto Precharge
Auto precharge is a feature that performs the same individual-bank precharge function described above but without requiring an
explicit command. This is accomplished by using A8 to enable auto precharge in conjunction with a specific READ or WRITE command. A precharge of the bank/row that is addressed with the READ or WRITE command is automatically performed upon completion of the READ or WRITE burst. Auto precharge is nonpersistent in that it is either enabled or disabled for each individual Read or
Write command. Auto precharge ensures that the precharge is initiated at the earliest valid stage within a burst. This “earliest valid
stage” is determined as if an explicit PRECHARGE command was issued at the earliest possible time, without violating tRAS min, as
described for each burst type in the Operation section of this data sheet. The user must not issue another command to the same
bank until the precharge time (tRP) is completed.
AUTO REFRESH
The addressing is generated by the internal refresh controller. This makes the address bits a Don’t Care during an AUTO REFRESH
command. The 512Mb x32 GDDR3 SDRAM requires AUTO REFRESH cycles at an average interval of 3.9us (maximum). A maximum of
eight AUTO REFRESH commands can be posted to any given GDDR3 SDRAM, meaning that the maximum absolute interval between
any AUTO REFRESH command and the next AUTO REFRESH command is 9 x 3.9us (35.1us). This maximum absolute interval allows
GDDR3 SDRAM output drivers to automatically recalibrate to compensate for voltage and temperature changes. AUTO REFRESH is
used during normal operation of the GDDR3 SDRAM and is analogous to CAS#-BEFORE-RAS# (CBR) refresh in FPM/EDO DRAMs.This
command is nonpersistent, so it must be issued each time a refresh is required.
SELF REFRESH
The SELF REFRESH command can be used to retain data in the GDDR3 SDRAM, even if the rest of the system is powered down.
When in the self refresh mode, the GDDR3 SDRAM retains data without external clocking. The SELF REFRESH command is initiated
like an AUTO REFRESH command except CKE is disabled(LOW). The DLL is automatically disabled upon entering SELF REFRESH and
is automatically enabled and reset upon exiting SELF REFRESH. The on-die termination is also disabled upon entering Self Refresh
except for CKE and enabled upon exiting Self Refresh. (5K clock cycles must then occur before a READ command can be issued).
Input signals except CKE are ”Don’t Care” during SELF REFRESH. The procedure for exiting self refresh requires a sequence of commands. First, CK and CK# must be stable prior to CKE going back HIGH. Once CKE is HIGH, the GDDR3 SDRAM must have NOP commands issued for tXSNR because time is required for the completion of any internal refresh in progress. A simple algorithm for
meeting both refresh and DLL requirements and output calibration is to apply NOPs for 1000 clock cycles before applying any other
command to allow the DLL to lock and the output drivers to recalibrate. If the GDDR3 device enters SELF REFRESH with the DLL disabled the GDDR3 device will exit SELF REFRESH with the DLL disabled.
DATA TERMINATOR DISABLE
(BUS SNOOPING FOR READ COMMANDS)
Bus snooping for READ commands other than CS# is used to control the on-die termination in the dual load configuration. The
GDDR3 SDRAM will disable the on-die termination when a READ command is detected, regardless of the state of CS#, when the ODT
for the DQ pins are set for dual loads (120Ω ).The on-die termination is disabled x clocks after the READ command where x equals
CL-1 and stay off for a duration of BL/2 +2CK, as shown in Figure8, Data Termination Disable Timing on page15. In a two-rank system, both DRAM devices snoop the bus for READ commands to either device and both will disable the on-die termination if a READ
command is detected. The on-die termination for all other pins on the device are always turned-on for both a single-rank system and
a dual-rank system.
Boundary Scan Test Mode
The 512Mb GDDR3 incorporates a modified boundary scan test mode as an optional feature. This mode doesn’t operate in accordance with IEEE Standard 1149.11990. To save the current GDDR3 ballout, this mode will scan the parallel data input and output the
scanned data through WDQS0 pin controlled by an addon pin, SEN which is located at U4 of 136 ball package. You can find the
detailed descriptions of this feature on Appendix C (page 62).
Rev.1.5 / Jul. 2008
21
H5RS5223CFR
Figure 8: Data Termination Disable Timing
NOTE:
1. DO n = data-out from column n.
2. Burst length = 4.
3. Three subsequent elements of data-out appear in the specified order following DO n.
4. Shown with nominal tAC and tDQSQ.
5. RDQS will start driving high one-half clock cycle prior to the first falling edge.
6. The Data Terminators are disabled starting at CL - 1 and the duration is BL/2 + 2CK.
7. READS to either rank disable both ranks’ termination regardless of the logic level of CS#.
Rev.1.5 / Jul. 2008
22
H5RS5223CFR
Operations
Bank/Row Activation
Figure 9: Activating a Specific
Row in a Specific Bank
Before any READ or WRITE commands can be issued to a bank within
the GDDR3 device, a row in that bank must be “opened.”
This is accomplished via the ACTIVE command, which selects both the
bank and the row to be activated, as shown in Figure 9, Activating a Specific Row in a Specific Bank. After a row is opened with an ACTIVE command, a READ or WRITE command may be issued to that row, subject to
the tRCD specification. tRCD min should be divided by the clock period
and rounded up to the next whole number to determine the earliest clock
edge after the ACTIVE command on which a READ or WRITE command
can be entered. For example, a tRCD specification of 15ns with a 550
MHz clock(1.8ns period) results in 7.5 clocks rounded to 8.
This is reflected in Figure 10, Example: Meeting tRCD, which overs any
cases where 7 < tRCDMIN/tCK <= 8. The same procedure is used to
convert other specification limits from time units to clock cycles. A subsequent ACTIVE command to a different row in the same bank can only be
issued after the previous active row has been "closed" (precharged). The
minimum time interval between successive ACTIVE commands to the
same bank is defined by tRC. A subsequent ACTIVE command to another
bank can be issued while the first bank is being accessed,which results in
a reduction of total row-access overhead. The minimum time interval
between successive ACTIVE commands to different banks is defined by
tRRD.
Figure 10: Example: Meeting tRCD
Rev.1.5 / Jul. 2008
23
H5RS5223CFR
READ Timing
READ burst is initiated with a READ command.
The starting column and bank addresses are provided with the READ command and auto precharge is either enabled or disabled for
that burst access with the A8 pin. If auto precharge is enabled, the row being accessed is precharged at the completion of the burst
after tRAS min has been met.
During READ bursts, the first valid data-out element from the starting column address will be available following the CAS latency after
the READ command. Each subsequent data-out element will be valid nominally at the next positive or negative RDQS edges. The
GDDR3 SDRAM drives the output data edge aligned to RDQS. And all outputs, i.e. DQs and RDQS, are also edge aligned to the clock.
Prior to the first valid RDQS rising edge, a cycle is driven and specified as the READ preamble. The preamble consists of a half cycle
High followed by a half cycle Low driven by the GDDR3 SDRAM. The cycle on RDQS consisting of a half cycle Low coincident with the
last data-out element followed by a half cycle High is known as the read postamble, and it will be driven by the SDRAM. The SDRAM
toggles RDQS only when it is driving valid data out onto on the bus.
Upon completion of a burst, assuming no other command has been initiated; the DQs and RDQS will go to be in Hi-Z state. VDDQ
due to the on die termination. long as the bus turn around time is met. READ data cannot be terminated or truncated.
A PRECHARGE can also be issued to the SDRAM with the same timing restriction as the new READ command if tRAS is met as shown
in Figure 17, READ to Precharge, on page 29. A WRITE can be issued any time after a READ command as long as the bus turn around
time is met as shown in Figure 16, READ to WRITE, on page 28. READ data cannot be terminated or truncated
Rev.1.5 / Jul. 2008
24
H5RS5223CFR
Figure 12: READ Burst
NOTE:
1. DO n = data-out from column n.
2. Burst length = 4.
3. Three subsequent elements of data-out appear in the specified order following DO n.
4. Shown with nominal tAC and tDQSQ.
5. RDQS will start driving high one-half clock cycle prior to the first falling edge.
Rev.1.5 / Jul. 2008
25
H5RS5223CFR
Figure 13: Consecutive READ Bursts
NOTE:
1. DO n (or b) = data-out from column n (or column b).
2. Burst length = 4
3. Three subsequent elements of data-out appear in the programmed order following DO n.
4. Three subsequent elements of data-out appear in the programmed order following DO b.
5. Shown with nominal tAC, and tDQSQ.
6. Example applies only when READ commands are issued to same device.
7. RDQS will start driving high one half clock cycle prior to the first falling edge of RDQS.
Rev.1.5 / Jul. 2008
26
H5RS5223CFR
Figure 14: Non-Consecutive READ Bursts
NOTE:
1. DO n (or b) = data-out from column n (or column b).
2. Burst length = 4.
3. Three subsequent elements of data-out appear in the programmed order following DO n.
4. Three subsequent elements of data-out appear in the programmed order following DO b.
5. Shown with nominal tAC and tDQSQ.
6. Example applies when READ commands are issued to different devices or nonconsecutive READs.
7. RDQS will start driving high one-half clock cycle prior to the first falling edge of RDQS.
Rev.1.5 / Jul. 2008
27
H5RS5223CFR
Figure 15: Random Read Accesses
NOTE:
1. DO n (or x or b or g) = data-out from column n (or column x or column b or column g).
2. Burst length = 4.
3. READs are to an active row in any banks.
4. Shown with nominal tAC and tDQSQ.
5. RDQS will start driving high one-half clock cycle prior to the first falling edge of RDQS.
Rev.1.5 / Jul. 2008
28
H5RS5223CFR
Figure 16: Read to Write
T0
T7
T8
T9
T10
T11
T12
CMD
READ
NOP
WRITE
NOP
NOP
NOP
NOP
ADD
Bank
Col n
CK#
CK
Bank
Col b
CL=7
WL=3
RDQS
WDQS
DQ
ODT
DQn
ODT On
DI b
On-Die Termination Off
On-Die Termination On
CL=7, BL=4, WL=3
NOTE:
1. DQ n = Data-out from column n.
2. DI b = Data-in from column b.
3. Shown with nominal tAC, tDQSQ and tDQSS.
4. Read Preamble consists of a half cycle High followed by a half cycle Low driven by device
5. Write Data cannot be driven onto the DQ bus for 2 clocks after the READ data is off the bus.
6. The timing diagram covers a READ to a WRITE command from different device, different bank or the same row in the same bank.
Rev.1.5 / Jul. 2008
29
H5RS5223CFR
Figure 17: READ to Precharge
NOTE:
1. DO n = data-out from column n.
2. Burst length = 4.
3. Three subsequent elements of data-out appear in the programmed order following DO n.
4. Shown with nominal tAC and tDQSQ.
5. READ to PRECHARGE equals two clocks, which enables two data pairs of data-out.
6. PRE = PRECHARGE command; ACT = ACTIVE command.
7. RDQS will start driving high one-half clock cycle prior to the first falling edge of RDQS.
Rev.1.5 / Jul. 2008
30
H5RS5223CFR
WRITE Timing
WRITE burst is initiated with a WRITE command.
The starting column and bank addresses are provided with the WRITE command, and auto precharge is either enabled or disabled
for that access with the A8 pin. If auto precharge is enabled, the row being accessed is precharged at the completion of the burst.
During WRITE bursts, the first valid data-in element will be registered on the rising edge of WDQS following the write latency set in
the mode register and subsequent data elements will be registered on successive edges of WDQS. Prior to the first valid WDQS rising
edge, a cycle is needed and specified as the WRITE Preamble. The preamble consists of a half cycle High followed by a half cycle Low
driven by the controller. The cycle on WDQS following the last data-in element is known as the write postamble and must be driven
High by the controller, it can not be left to float High using the on die termination. The WDQS should only toggle on data transfers.
The time between the WRITE command and the first valid rising edge of WDQS (tDQSS) is specified relative to the write latency (WL
- 0.25tCK and WL + 0.25tCK). All of the WRITE diagrams show the nominal case, and where the two extreme cases (i.e., tDQSS
[MIN] and tDQSS [MAX]) might not be intuitive, they have also been included. Upon completion of a burst, assuming no other command has been initiated, the DQs should remain Hi-Z and any additional input data will be ignored.
Data for any WRITE burst may not be truncated with any subsequent command. A subsequent WRITE command can be issued on
any positive edge of clock following the previous WRITE command assuming the previous burst has completed. The subsequent
WRITE command can be issued x cycles after the previous WRITE command, where x equals the number of desired nibbles x2 (nibbles are required by 4n-prefetch architecture) i.e. BL/2. A subsequent READ command can be issued once tWTR is met or a subsequent PRECHARGE command can be issued once tWR is met. After the PRECHARGE command, a subsequent command to the same
bank cannot be issued until tRP is met.
Rev.1.5 / Jul. 2008
31
H5RS5223CFR
Figure 19: WRITE Burst
NOTE:
1. DI b = data-in for column b.
2. Three subsequent elements of data-in are applied in the specified order following DI b.
3. A burst of 4 is shown.
4. A8 is LOW with the WRITE command (auto precharge is disabled).
5. Write latency is set to 4.
Rev.1.5 / Jul. 2008
32
H5RS5223CFR
Figure 20: Consecutive WRITE to WRITE
NOTE:
1. DI b, etc. = data-in for column b, etc.
2. Three subsequent elements of data-in are applied in the specified order following DI b.
3. Three subsequent elements of data-in are applied in the specified order following DI n.
4. Burst of 4 is shown.
5. Each WRITE command may be to any bank of the same device.
6. WRITE latency is set to 3.
Rev.1.5 / Jul. 2008
33
H5RS5223CFR
Figure 21: NonConsecutive WRITE to WRITE
NOTE:
1. DI b, etc. = data-in for column b, etc.
2. Three subsequent elements of data-in are applied in the specified order following DI b.
3. Three subsequent elements of data-in are applied in the specified order following DI n.
4. A burst of 4 is shown.
5. Each WRITE command may be to any banks.
6. WRITE latency set to 3.
Rev.1.5 / Jul. 2008
34
H5RS5223CFR
Figure 22: Random WRITE Cycles
NOTE:
1. DI b, etc. = data-in for column b, etc.
2. b', etc. = the next data-in following DI b, etc., according to the specified burst order.
3. Programmed burst length = 4 case is shown.
4. Each WRITE command may be to any banks.
5. Last write command will have the rest of the nibble on T8 and T8n.
6. WRITE latency is set to 3.
Rev.1.5 / Jul. 2008
35
H5RS5223CFR
Figure 23: WRITE to READ Timing
NOTE:
1. DI b = Data In for column b
2. Three subsequent elements of Data In are applied following D1 b
3. tWTR is referenced from the first positive CK edge after the last Data In
4. The READ and WRITE commands may be to any bank.
5. WRITE Latency is set to 1
6. The 4n prefetch architecture requires a 2-clock WRITE-to-READ turn around time (tWTR).
Rev.1.5 / Jul. 2008
36
H5RS5223CFR
Figure 24: WRITE to PRECHARGE
NOTE:
1. DI b = data-in for column b.
2. Three subsequent elements of data-in are applied in the specified order following DI b.
3. A burst of 4 is shown.
4. A8 is LOW with the WRITE command (auto precharge is disabled).
5. WRITE latency is set to 3.
Rev.1.5 / Jul. 2008
37
H5RS5223CFR
PRECHARGE
The PRECHARGE command (shown in Figure25) issused to deactivate the open row in a particular bank or the open row in all banks.
The bank(s) will be available for a subsequent row access some specified time (tRP) after the precharge command is issued. Input A8
determines whether one or all banks are to be precharged, and in the case where only one bank is to be precharged, inputs BA0-BA2
select the bank. When all banks are to be precharged, inputs BA0-BA2 are treated as “Don’t Care.” Once a bank has been precharged, it is in the idle state and must be activated prior to any READ or WRITE commands being issued to that bank.
Figure 25: PRECHARGE Command
POWER-DOWN (CKE Not Active)
Unlike SDR SDRAMs, GDDR3 SDRAMs require CKE to be active at all times that an access is in progress: from the issuing of a READ
or WRITE command until completion of the burst. For READs, a burst completion is defined when the Read Postamble is satisfied; For
WRITEs, a burst completion is defined when the write postamble is satisfied. Power-down (shown in Figure26, Power-Down, on
page38) is entered when CKE is registered low. If power-down occurs when all banks are idle, this mode is referred to as precharge
power-down; if power-down occurs when there is a row active in any banks, this mode is referred to as active power-down. Entering
power-down deactivates the input and output buffers, excluding CK, CK# and CKE. For maximum power savings, the user also has
the option of disabling the DLL prior to entering power-down. In that case, the DLL must be enabled and reset after exiting powerdown, and 5K clock cycles must occur before a READ command can be issued. However, power-down duration is limited by the
refresh requirements of the device, so in most applications, the self refresh mode is preferred over the DLL-disabled power-down
mode. While in power-down, CKE LOW and a stable clock signal must be maintained at the inputs of the GDDR3 SDRAM, while all
other input signals are “Don’t Care.” The power-down state is synchronously exited when CKE is registered HIGH (in conjunction with
a NOP or DESELECT command). A valid executable command may be applied four clock cycles later.
Rev.1.5 / Jul. 2008
38
H5RS5223CFR
Figure 26: Power-Down
Table 8: Truth Table - CKE
Notes: 1~4; notes appear below table
CKEn-1
CKEn
CURRENT STATE
COMMANDn
ACTIONn
L
L
Power-Down
X
Maintain Power-Down
L
L
Self Refresh
X
Maintain Self Refresh
L
H
Power-Down
DESELECT or NOP
Exit Power-Down
L
H
Self Refresh
DESELECT or NOP
Exit Self Refresh
H
L
All Banks Idle
DESELECT or NOP
Precharge Power-Dwon Entry
H
L
Bank(s) Active
DESELECT or NOP
Active Power-Down Entry
H
L
All Banks Idle
AUTO REFRESH
Self Refresh Entry
H
H
NOTES
5
See Truth Table 3
NOTE:
1. CKEn is the logic state of CKE at clock edge n; CKEn-1 was the state of CKE at the previous clock edge.
2. Current state is the state of the GDDR3 SDRAM immediately prior to clock edge n.
3. COMMANDn is the command registered at clock edge n, and ACTIONn is a result of COMMANDn.
4. All states and sequences not shown are illegal or reserved.
5. DESELECT or NOP commands should be issued on any clock edges occurring during the tXSR period. A minimum of 5K clock
cycles is needed for the DLL to lock before applying a READ command if the DLL was disabled.
Rev.1.5 / Jul. 2008
39
H5RS5223CFR
Table 9: Truth Table 3 - Current State Bank n - Command to Bank n
Notes: 1~3; notes appear below table
CURRENT
STATE
CS#
Any
H
X
X
X
DESELECT (NOP/continue previous operation)
L
H
H
H
NO OPERATION (NOP/continue previous operation)
L
L
H
H
ACTIVE (select and activate row)
Idle
Row Active
RAS#
CAS#
WE#
COMMAND/ACTION
NOTES
L
L
L
H
AUTO REFRESH
L
L
L
L
LOAD MODE REGISTER
4
4
L
H
L
H
READ (select column and start READ burst)
6
L
H
L
L
WRITE (select column and start WRITE burst)
6
L
L
H
L
PRECHARGE (deactivate row in bank or banks)
5
Read
(Auto Precharge
Disabled)
L
H
L
H
READ (select column and start new READ burst)
6
L
H
L
L
WRITE (select column and start WRITE burst)
L
L
H
L
PRECHARGE (truncate READ burst , start Precharge)
Write
(Auto Precharge
Disabled)
L
H
L
H
READ (select column and start READ burst)
L
H
L
L
WRITE (select column and start new WRITE burst)
L
L
H
L
PRECHARGE (truncate WRITE burst, start Precharge)
6, 8
5
6, 7
6
5, 7
NOTE:
1. This table applies when CKEn-1 was HIGH and CKEn is HIGH (see Truth Table 2) and after tXSNR has been met
(if the previous state was self refresh).
2. This table is bank-specific, except where noted (i.e., the current state is for a specific bank and the commands shown are those
allowed to be issued to that bank when in that state). Exceptions are covered in the notes below.
3. Current state definitions:
Idle: The bank has been precharged, and tRP has been met.
Row Active: A row in the bank has been activated, and tRCD has been met. No data bursts/accesses and no register accesses are
in progress.
Read: A READ burst has been initiated, with auto precharge disabled.
Write: A WRITE burst has been initiated, with auto precharge disabled.
4. The following states must not be interrupted by a command issued to the same bank. COMMAND INHIBIT or NOP commands, or
allowable commands to the other bank should be issued on any clock edge occurring during these states. Allowable commands to
the other bank are determined by its current state and Table9, and according to Table10. Precharging: Starts with registration of
a PRECHARGE command and ends when tRP is met. Once tRP is met, the bank will be in the idle state.
Row Activating: Starts with registration of an ACTIVE command and ends when tRCD is met. Once tRCD is met, the bank will be in
the “row active” state.
Read w/Auto-Precharge Enabled: Starts with registration of a READ command with auto precharge enabled and ends when tRP
has been met. Once tRP is met, the bank will be in the idle state.
Write w/Auto-Precharge Enabled: Starts with registration of a WRITE command with auto precharge enabled and ends when tRP
has been met. Once tRP is met, the bank will be in the idle state.
5. The following states must not be interrupted by any executable command; COMMAND INHIBIT or NOP commands must be applied
on each positive clock edge during these states.
Refreshing: Starts with registration of an AUTO REFRESH command and ends when tRC is met. Once tRC is met, the GDDR3 x32
will be in the all banks idle state.
Accessing Mode Register: Starts with registration of a LOAD MODE REGISTER command and ends when tMRD has been met.
Once tMRD is met, the GDDR3 x32 will be in the all banks idle state.
Precharging All: Starts with registration of a PRECHARGE ALL command and ends when tRP is met. Once tRP is met, all banks will
be in the idle state. READ or WRITE: Starts with the registation of the ACTIVE command and ends the last valid data nibble.
6. All states and sequences not shown are illegal or reserved.
7. Not bank-specific; requires that all banks are idle, and bursts are not in progress.
8. May or may not be bank-specific; if multiple banks are to be precharged, each must be in a valid state for
precharging.
9. Reads or Writes listed in the Command/Action column include Reads or Writes with auto precharge enabled and Reads or Writes
with auto precharge disabled.
10. Requires appropriate DM masking.
11. A WRITE command may be applied after the completion of the READ burst
Rev.1.5 / Jul. 2008
40
H5RS5223CFR
Table 10: Truth Table - Current State Bank n - Command to Bank m
Notes: 1~5; notes appear below table
CURRENT
STATE
CS#
Any
H
X
X
X
DESELECT (NOP/continue previous operation)
L
H
H
H
NO OPERATION (NOP/continue previous operation)
Idle
X
X
X
X
Any Command Otherwise Allowed to Bank m
Row Activating, Active, or
Precharging
L
L
H
H
ACTIVE (select and activate row)
L
H
L
H
READ (select column and start READ burst)
6
L
H
L
L
WRITE (select column and start WRITE burst)
6
L
L
H
L
PRECHARGE
L
L
H
H
ACTIVE (select and activate row)
L
H
L
H
READ (select column and start new READ burst)
6
L
H
L
L
WRITE (select column and start WRITE burst)
6
L
L
H
L
PRECHARGE
L
L
H
H
ACTIVE (select and activate row)
L
H
L
H
READ (select column and start READ burst)
L
H
L
L
WRITE (select column and start new WRITE burst)
L
L
H
L
PRECHARGE
L
L
H
H
ACTIVE (select and activate row)
L
H
L
H
READ (select column and start new READ burst)
6
L
H
L
L
WRITE (select column and start WRITE burst)
6
L
L
H
L
PRECHARGE
L
L
H
H
ACTIVE (select and activate row)
L
H
L
H
READ (select column and start READ burst)
6
L
H
L
L
WRITE (select column and start new WRITE burst)
6
L
L
H
L
PRECHARGE
Read (Auto
Precharge Disabled)
Write (Auto
Precharge Disabled)
Read(With
Auto Precharge)
Write(With
Auto Precharge)
RAS#
CAS#
WE#
COMMAND/ACTION
NOTES
6, 7
6
NOTE:
1. This table applies when CKEn-1 was HIGH and CKEn is HIGH (see Table9) and after tXSNR has been met
(if the previous state was self refresh).
2. This table describes alternate bank operation, except where noted (i.e., the current state is for bank n and the commands shown
are those allowed to be issued to bank m, assuming that bank m is in such a state that the given command is allowable).
Exceptions are covered in the notes below.
3. Current state definitions:
Idle: The bank has been precharged, and tRP has been met.
Row Active: A row in the bank has been activated, and tRCD has been met. No data bursts/accesses and no register accesses are
in progress.
Read: A READ burst has been initiated, with auto precharge disabled.
Write: A WRITE burst has been initiated, with auto precharge disabled.
Read with Auto Precharge Enabled: See following text
Write with Auto Precharge Enabled: See following text
Rev.1.5 / Jul. 2008
41
H5RS5223CFR
3a. The read with auto precharge enabled or write with auto precharge enabled states can each be broken into two parts: the
access period and the precharge period. For read with auto precharge, the precharge period is defined as if the same burst was executed with auto precharge disabled and then followed with the earliest possible PRECHARGE command that still accesses all of the
data in the burst. For write with auto precharge, the precharge period begins when tWR ends, with tWR measured as if auto precharge was disabled. The access period starts with registration of the command and ends where the precharge period (or tRP)
begins. During the precharge period of the read with auto precharge enabled or write with auto precharge enabled states, ACTIVE,
PRECHARGE, READ and WRITE commands to the other bank may be applied. In either case, all other related limitations apply (e.g.,
contention between read data and write data must be avoided).
3b. The minimum delay from a READ or WRITE command with auto precharge enabled, to a command to a different bank is summarized below.
4. AUTO REFRESH and LOAD MODE REGISTER commands may only be issued when all banks are idle.
5. All states and sequences not shown are illegal or reserved.
6. READs or WRITEs listed in the Command/Action column include READs or WRITEs with auto precharge enabled and READs or
WRITEs with auto precharge disabled.
7. Requires appropriate DM masking.
Table 11: Minimum Delay Between Commands to Different Banks with Auto
Precharge Enabled
From Command
To Command
READ or READ with AUTO PRECHARGE
WRITE with
AUTO PRECHARGE
WRITE or WRITE with AUTO PRECHARGE
[WL + (BL/2)] tCK + tWTR
(BL/2) tCK
PRECHARGE
1 tCK
ACTIVE
1 tCK
READ or READ with AUTO PRECHARGE
READ with
AUTO PRECHARGE
Minimum delay
(with concurrent auto precharge)
WRITE or WRITE with AUTO PRECHARGE
(BL/2) * tCK
[CL + (BL/2) + 2 - WL] * tCK 1)
PRECHARGE
1 tCK
ACTIVE
1 tCK
NOTE:
CL = CAS latency (CL) rounded up to the next integer.
BL = Burst length.
WL = WRITE latency.
1) Write Data connot be driven onto the DQ bus for 2 clocks after the READ data is off the bus.(refer to Fig16. on the page29)
Rev.1.5 / Jul. 2008
42
H5RS5223CFR
OPERATING CONDITIONS
Absolute Maximum Ratings*
Voltage on Vdd Supply
Relative to Vss .............................................-0.5V to +2.5V
Voltage on VddQ Supply
Relative to Vss .............................................-0.5V to +2.5V
Voltage on Vref and Inputs
Relative to Vss .............................................-0.5V to +2.5V
Voltage on I/O Pins
Relative to Vss ....................................-0.5V to VddQ +0.5V
MAX Junction Temperature, TJ ...........................+125℃
Storage Temperature (plastic)................-55℃ to +150℃
Power Dissipation..........................................................TBD
Short Circuit Output Current......................................50mA
* Stresses greater than those listed may cause permanent damage to the device. This is a stress rating only, and functional operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Exposure to absolute maximum rating conditions for extended periods may affect reliability.
Table 12: Thermal Characteristics
PARAMETER
Description
Value
UNIT
NOTES
TC
Case Temperature
115.0
℃
7
TJ
Junction Temperature
126.2
℃
7
Theta_JA
Thermal resistance junction to ambient
47.8
℃/W
1,2,3,4,5,7
Theta_JC
Thermal resistance junction to case
9.0
℃/W
1,2,6,7
Note:
1. Measurement procedures for each parameter must follow standard procedures defined in the current JEDEC JESD-51 standared.
2. Theta_JA and Theta_JC must be measured with the high effective thermal conductivity test board defined in JESD51-7
3. Airflow information must be deocumented for Theta_JA.
4. Theta_JA should only be used for comparing the thermal performance of signle packages and not for system related junction.
5. Theta_JA is the natural convection junction-to-ambient air thermal resistance measured in one cubic foot sealed enclosure
as described in JESD-51. The environment is sometimes referred to as “still-air” although natural convection causes the air to move.
6. Theta_JC case surface is defined as the “outside surface of the package (case) closest to the chip mounting area when that same
surface is properly hear sunk” so as to minimize temperature variation across that surface.
7. Test condition : Voltage 2.15V(Maximum voltage) / Frequency : 1.2Ghz
Rev.1.5 / Jul. 2008
43
H5RS5223CFR
Table 13: DC Electrical Characteristics and Operating Conditions
(Recommended operating conditions; 0℃ <= TC <= 85℃)
PARAMETER/CONDITION
SYMBOL
MIN
TYP
MAX
UNITS
Remark
1.95
2.05
2.15
V
1,5
1.7
1.8
2.15
V
2,5
1.455
1.5
1.545
V
3,5
VREF
0.69xVDDQ
0.70xVDDQ
0.71xVDDQ
V
4
Input High (Logic 1) Voltage
VIH(DC)
VREF+0.15
-
-
V
Input Low (Logic 0) Voltage
VIL(DC)
-
-
VREF-0.15
V
INPUT LEAKAGE CURRENT Any Input 0V <= Vin <=
Vdd (All other pins not under test = 0V)
II
-5
-
5
uA
IOZ
-5
-
5
uA
VOL(DC)
-
-
0.76
V
Supply Voltage /
I/O Supply Voltage
VDD/
VDDQ
I/O Reference Voltage
OUTPUT LEAKAGE CURRENT
(DQs are disabled; 0V <= Vout <= VddQ)
OUTPUT Logic Low
NOTE :
1. It supports 1G/1.2/1.3GHz speed at H5RS5223CFR-N0C/ N2C/N3C
2. It supports 500/700/900MHz speed at H5RS5223CFR-20C / 14C / 11C.
3. It supports 550/700MHz speed at H5RS5223CFR-18C / 14L.
4. VREF is expected to equal 70% of VDDQ for the transmitting device and to track variations in the DC level of the same. AC noise
on VREF may not exceed +/- 2 percent of the DC value.
5. Under all conditions, VDDQ must be or equal to VDD.
Table 14: AC Input Operating
(Recommended operating conditions; 0℃ <= TC <= 85℃)
PARAMETER/CONDITION
SYMBOL
MIN
TYP
MAX
UNITS
Input High (Logic 1) Voltage; DQ
VIH(AC)
VREF+0.250
-
-
V
Input Low (Logic 0) Voltage; DQ
VIL(AC)
-
-
VREF-0.250
V
Clock Input Differential Voltage; CK and CK#
Vid(AC)
0.22
-
VDDQ+0.3
V
Clock Input Crossing Point Voltage; CK and CK#
Vix(AC)
VREF-0.15
-
VREF+0.15
V
Rev.1.5 / Jul. 2008
44
H5RS5223CFR
OUTPUT IMPEDANCE AND TERMINATION DC ELECTRICAL CHARACTERISTICS
The Driver and Termination impedances are determined by applying VDDQ/2 nominal (0.9v) at the corresponding input or output
and by measuring the current flowing into or out of the device. VDDQ is set to the nominal 1.8v.
•
IOH is the current flowing out of DQ when the Pull-up transistor is activated and the DQ termination is disabled
•
IOL is the current flowing out of DQ when the Pull-down transistor is activated and the DQ termination is disabled
•
ITCAH(ZQ/2) is the current flowing out of the Termination of Commands and Addresses for a ZQ/2 termination value
•
ITCAH(ZQ) is the current flowing out of the Termination of Commands and Addresses for a ZQ termination value.
•
ITDQH(ZQ/4) is the current flowing out of the Termination of the DQs for a ZQ/4 termination value.
•
ITDQH(ZQ/2) is the current flowing out of the Termination of the DQs for a ZQ/2 termination value
Note:
Measurement performed with VDDQ = 1.8v (nominal) and by applying VDDQ/2 (0.9v) at the corresponding Input or Output. (0℃ <=
Tc <= +85℃)
Table 15: Driver and Termination DC Characteristics (1.8V version)
200
PARAMETER
240
280
OHM
ZQ VALUE
MIN
MAX
MIN
MAX
MIN
MAX
UNITS
30.0
20.5
25.0
17.5
21.4
mA
IOH
ZQ/6
24.5
IOL
ZQ/6
24.5
30.0
20.5
25.0
17.5
21.4
mA
ITCAH (ZQ/2)
ZQ/2
8.2
10.0
6.8
8.3
5.8
7.1
mA
ITCAH (ZQ)
ZQ
4.1
5.0
3.4
4.2
11.7
14.3
mA
ITDQH (ZQ/4)
ZQ/4
16.4
18.0
13.6
16.7
11.7
14.3
mA
ITDQH (ZQ/2)
ZQ/2
8.2
10.0
6.8
8.3
5.8
7.1
mA
Rev.1.5 / Jul. 2008
NOTES
45
H5RS5223CFR
Figure 27: Input and Output Voltage Waveform
Rev.1.5 / Jul. 2008
46
H5RS5223CFR
Table 16: Clock Input Operating Conditions (1.8V version)
PARAMETER/CONDITION
SYMBOL
MIN
TYP
MAX
UNITS
Clock Input Midpoint Voltage; CK and CK#
VMP(DC)
1.16
1.26
1.36
V
Clock Input Voltage Level; CK and CK#
VIN(DC)
0.42
-
VDDQ+0.3
V
Clock Input Differential Voltage; CK and CK#
VID(DC)
0.22
VDDQ
V
Clock Input Differential Voltage; CK and CK#
VID(AC)
0.22
VDDQ+0.3
V
Clock Input Crossing Point Voltage; CK and CK#
VIX(AC)
VREF-0.15
VREF+0.15
V
0.70xVDDQ
Figure 28: Clock Input
NOTE:
1. This provides a minimum of 1.16V to a maximum of 1.36V, and is always 70% of VDDQ.
2. CK and CK# must cross in this region.
3. CK and CK# must meet at least VIN(DC) MIN when static and is centered around VMP(DC).
4. CK and CK# must have a minimum 600mV peak-to-peak swing.
5. CK or CK# may not be more positive than VDDQ + 0.5V or lower than 0.22V.
6. For AC operation, all DC clock requirements must also be satisfied.
7. Numbers in diagram reflect nominal values.
Rev.1.5 / Jul. 2008
47
H5RS5223CFR
Table 17: Capacitance
Note: 13; notes appear on pages 52, 53
PARAMETER
SYMBOL
MIN
MAX
UNITS
NOTES
Delta Input/Output Capacitance: DQs, DQS, DM
DCIO
-
0.20
pF
24
Delta Input Capacitance: Command and Address
DCI1
-
0.40
pF
29
29
Delta Input Capacitance: CK, CK#
DCI2
-
0.10
pF
Input/Output Capacitance: DQs, DQS, DM
CIO
1.5
3.5
pF
Input Capacitance: Command and Address
CI1
1.0
3.0
pF
Input Capacitance: CK, CK#
CI2
1.0
3.0
pF
Input Capacitance: CKE
CI3
1.0
3.0
pF
Table 18: IDD Specifications and Conditions (Units : mA)
Note:1-5, 10, 12, 14, 40; notes on page 52, 53; 0℃ <= TC <= 85℃
PARAMETER/CONDITION
SYMBOL
MAX
-18C -14L -20C -14C -11C -N0C -N2C -N3C
NOTES
OPERATING CURRENT: One bank; Active-Precharge; tRC
(MIN); tCK = tCK (MIN); DQ, DM, and DQS inputs changing
twice per clock cycle; Address and control inputs changing
once per clock cycle; WL=6
IDD0
140
160
160
200
240
300
350
400
22, 46
OPERATING CURRENT: One bank; Active Read Precharge;
Burst = 4; tRC (MIN); tCK = tCK (MIN); Address and control
inputs changing once per clock cycle; I(OUT) =0mA; WL=6
IDD1
140
160
160
200
240
300
350
400
22, 46
PRECHARGE POWER-DOWN STANDBY CURRENT: All banks
idle; Power-down mode; tCK = tCK (MIN); CKE= LOW
IDD2P
30
40
60
70
80
90
110
130
32
IDLE STANDBY CURRENT: CS# = HIGH; All banks idle; tCK =
IDD2N
tCK (MIN); CKE = HIGH; inputs changing once per clock cycle
60
80
80
100
120
170
250
300
ACTIVE POWER-DOWN STANDBY CURRENT: One bank active;
Power-down mode; tCK = tCK (MIN); CKE= LOW; WL=6
IDD3P
40
50
60
70
80
100
150
180
32
ACTIVE STANDBY CURRENT: CS# = HIGH; CKE = HIGH; One
bank; Active Precharge; tRC = tRAS (MAX); tCK = tCK (MIN);
DQ, DM, and DQS inputs changing twice per clock cycle;
Address and other control inputs changing once per clock
cycle;WL=6
IDD3N
70
90
90
110
130
200
250
300
22
OPERATING CURRENT: Burst = 4; Reads; Continuous burst;
One bank active; Address and control inputs changing once
per clock cycle; tCK = tCK (MIN); I(OUT)=0mA; WL=6
IDD4R
330
420
450
500
650
800
950
1050
OPERATING CURRENT: Burst = 4; Writes; Continuous burst;
One bank active; Address and control inputs changing once
per clock cycle; tCK = tCK (MIN); DQ, DM, and DQS inputs
changing twice per clock cycle; WL=6
IDD4W
330
420
450
500
650
800
950
1050
tRFC (MIN)
IDD5A
230
250
250
300
350
400
500
600
22
tRFC = 3.9us
IDD5B
70
90
80
110
130
200
250
300
27
IDD6
10
10
20
20
20
25
25
25
11
AUTO REFRESH CURRENT
SELF REFRESH CURRENT: CKE <= 0.2V
NOTE :
1. ‘-18C/-14L’ means low voltage so its current is measured at 1.545max voltage.
2. H5RS5223CFR-20C/-14C/-11C is standardized by 1.9max voltage.
3. H5RS5223CFR-N0C/-N2C/-N3C is standardized by 2.1max voltage.
Rev.1.5 / Jul. 2008
48
H5RS5223CFR
Table 19: Electrical Characteristics and AC Operating Conditions
Notes: 1-5,14-16,33,40; notes on pages52, 53; 0℃ <= TC <=85℃
AC Characteristics Parameter
Parameter
-18C
-20C
-14(L)
Unit
Note
Symbol
MIN
MAX
MIN
MAX
Min
Max
tDQSCK
-0.35
+0.35
-0.26
+0.26
-0.35
+0.35
tCK
CK High-level width
tCH
0.45
0.55
0.45
0.55
0.45
0.55
tCK
CK Low-level width
tCL
0.45
0.55
0.45
0.55
0.45
0.55
tCK
30
CL=9
tCK
-
-
1.4
3.3
-
-
ns
33, 40, 48
CL=7
tCK
1.8
3.3
-
-
1.8
3.3
ns
33, 40, 48
Write Latency
tWL
1,2,3,4,
5,6
1,2,3,4,
5,6
1,2,3,4,
5,6
tCK
43
DQ & DM input hold time relative to
DQS
tDH
0.25
0.18
0.25
ns
26, 31
DQ & DM input setup time relative to
DQS
tDS
0.25
0.18
0.25
ns
26, 31
Active termination setup time
tATS
10
10
10
ns
Active termination hold time
tATH
10
10
10
ns
DQS input high pulse width
tDQSH
0.48
0.52
0.48
0.52
0.48
0.52
tCK
DQS input low pulse width
tDQSL
0.48
0.52
0.48
0.52
0.48
0.52
tCK
DQS-DQ skew
tDQSQ
-0.225
+0.225
-0.160
+0.160
-0.225
+0.225
ns
Write command to first DQS latching
transition
tDQSS
WL-0.2
WL+0.2
WL-0.2
WL+0.2
WL-0.2
WL+0.2
tCK
DQS falling edge to CK rising . setup
time
tDSS
0.25
0.25
0.25
tCK
DQS falling edge from CK rising . hold
time
tDSH
0.25
0.25
0.25
tCK
Half strobe period
tHP
tCL min
or
tCH min
tCL min
or
tCH min
tCL min
or
tCH min
tCK
Data output hold time from DQS
tQH
tHP0.225
tHP-0.16
tHP0.225
ns
Data-out high-impedance window from
CK/CK#
tHZ
0.3
0.3
0.3
ns
18
Data-out low-impedance window
fromCK/CK#
tLZ
0.3
0.3
0.3
ns
18
Address and control input hold time
tIH
0.5
0.35
0.5
ns
14
Address and control input setup time
tIS
0.5
0.35
0.5
ns
14
Address and control input pulse width
tIPW
1.3
1.0
1.3
ns
LOAD MODE REGISTER command cycle
time
tMRD
4
6
4
tCK
DQS out Access time from CK
Clock Cycle Time
Rev.1.5 / Jul. 2008
30
25, 26
34
44
49
H5RS5223CFR
AC Characteristics Parameter
Parameter
-18C
Symbol
MIN
-20C
-14(L)
MAX
MIN
MIN
Note
3.9
us
23
46
tREFI
DQS read preamble
tRPRE
0.4
0.6
0.4
0.6
0.4
0.6
tCK
DQS read postamble
tRPST
0.4
0.6
0.4
0.6
0.4
0.6
tCK
DQS write preamble
tWPRE
0.4
0.6
0.4
0.6
0.4
0.6
tCK
DQS write preamble setup time
tWPRES
0
DQS write postamble
tWPST
0.4
0.6
0.4
0.6
0.4
tJ
-
0.03
-
0.03
tDCERR
-
0.03
-
tR, tF
-
0.2
-
Cycle to cycle duty cycle error
Rise and fall times of CK
Rev.1.5 / Jul. 2008
3.9
Unit
MAX
Average periodic refresh interval
Jitter over 1~6 clock cycle error
3.9
MAX
0
0
ns
20, 21
0.6
tCK
19, 37
-
0.03
tCK
0.03
-
0.03
tCK
0.2
-
0.2
tCK
50
H5RS5223CFR
Table 19: Electrical Characteristics and AC Operating Conditions
Notes: 1-5,14-16,33,40; notes on pages 52, 53; 0℃ <= TC <=85℃
AC Characteristics Parameter
-11C
-N2C
-N0C
-N3C
Unit
Note
Symbol
MIN
MAX
MIN
MAX
Min
Max
Min
Max
tDQSCK
-0.22
+0.22
-0.2
+0.2
-0.2
+0.2
-0.2
+0.2
tCK
CK High-level width
tCH
0.45
0.55
0.45
0.55
0.45
0.55
0.45
0.55
tCK
30
CK Low-level width
tCL
0.45
0.55
0.45
0.55
0.45
0.55
0.45
0.55
tCK
30
CL=11
tCK
-
-
-
-
0.8
2
0.77
2
ns
33, 40, 48
CL=11
tCK
-
-
1
2
-
-
-
-
ns
33, 40, 48
CL=10
tCK
1.1
3.3
-
-
-
-
-
-
ns
33, 40, 48
Write Latency
tWL
1,2,3,
4,5,6
1,2,3,
4,5,6
1,2,3,
4,5,6
1,2,3,
4,5,6
tCK
43
DQ & DM input hold time relative
to DQS
tDH
0.15
0.13
0.125
0.125
ns
26, 31
DQ & DM input setup time relative to DQS
tDS
0.15
0.13
0.125
0.125
ns
26, 31
Active termination setup time
tATS
10
10
10
10
ns
Active termination hold time
tATH
10
10
10
10
ns
DQS input high pulse width
tDQSH
0.48
0.52
0.48
0.52
0.48
0.52
0.48
0.52
tCK
DQS input low pulse width
tDQSL
0.48
0.52
0.48
0.52
0.48
0.52
0.48
0.52
tCK
DQS-DQ skew
tDQSQ
-0.13
0.13
-0.12
0.12
-0.12
0.12
-0.12
0.12
ns
Write command to first DQS
latching transition
tDQSS
WL-0.2
WL+0.2
WL-0.2
WL+0.2
WL-0.2
WL+0.2
WL-0.2
WL+0.2
tCK
DQS falling edge to CK rising .
setup time
tDSS
0.25
0.25
0.25
0.25
tCK
DQS falling edge from CK rising .
hold time
tDSH
0.25
0.25
0.25
0.25
tCK
Half strobe period
tHP
tCL min
or
tCH min
tCL min
or
tCH min
tCL min
or
tCH min
tCL min
or
tCH min
tCK
Data output hold time from DQS
tQH
tHP0.13
tHP-0.12
tHP-0.12
tHP-0.12
ns
Data-out high-impedance window from CK/CK#
tHZ
-0.3
-0.3
-0.3
-0.3
ns
18
Data-out low-impedance window from CK/CK#
tLZ
-0.3
-0.3
-0.3
-0.3
ns
18
Address and control input hold
time
tIH
0.28
0.27
0.24
0.23
ns
14
Address and control input setup
time
tIS
0.28
0.27
0.24
0.23
ns
14
Address and control input pulse
width
tIPW
0.8
0.7
0.7
0.7
ns
Parameter
DQS-out access time from CK
Clock Cycle Time
Rev.1.5 / Jul. 2008
25, 26
34
51
H5RS5223CFR
Table 19: Electrical Characteristics and AC Operating Conditions
Notes: 1-5,14-16,33,40; notes on pages52, 53; 0℃ <= TC <=85℃
AC Characteristics Parameter
Parameter
-11C
N0C
-N2C
-N3C
Unit
Note
tCK
46
tCK
44
Symbol
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
DQS read preamble
tRPRE
0.4
0.6
0.4
0.6
0.4
0.6
0.4
0.6
LOAD MODE REGISTER command
cycle time
tMRD
7
DQS read postamble
tRPST
0.4
0.6
0.4
0.6
0.4
0.6
0.4
0.6
tCK
DQS write preamble
tWPRE
0.4
0.6
0.4
0.6
0.4
0.6
0.4
0.6
tCK
DQS write preamble setup time
tWPRES
0
DQS write postamble
tWPST
0.4
0.6
0.4
0.6
0.4
0.6
0.4
tJ
-
0.03
-
0.03
-
0.03
tDCERR
-
0.03
-
0.03
-
tR, tF
-
0.2
-
0.2
-
Jitter over 1~6 clock cycle error
Cycle to cycle duty cycle error
Rise and fall times of CK
7
7
0
0
Timing reference
point
VDDQ
7
0
ns
20, 21
0.6
tCK
19, 37
-
0.03
tCK
0.03
-
0.03
tCK
0.2
-
0.2
tCK
VDDQ
60Ω
Data out
GDDR3
10pF
ZQ
240Ω
AC timing reference load ( Refer to note3 on page52)
Rev.1.5 / Jul. 2008
52
H5RS5223CFR
Notes:
1. All voltages referenced to Vss.
2. Tests for AC timing, Idd, and electrical AC and DC characteristics may be conducted at nominal reference/supply voltage levels,
but the related specifications and device operation are guaranteed for the full voltage range specified.
3. Outputs measured with equivalent load of 10pf terminated with 60Ω to VddQ. The output timing reference voltage level for single
ended signals is the cross point with VREF (=0.7*VDDQ nominal).
4. AC timing and Idd tests may use a Vil-to-Vih swing of up to 1.0V in the test environment, but input timing is still referenced to Vref
(or to the crossing point for CK/CK#), and parameter specifications are guaranteed for the specified AC input levels under normal
use conditions. The minimum slew rate for the input signals used to test the device is 3V/ns in the range between Vil(AC) and
Vih(AC).
5. The AC and DC input level specifications are a pseudo open drain design for improved high-speed signaling.
6. Vref is expected to equal 70 percent of VddQ for the transmitting device and to track variations in the DC level of the same. Peakto-peak noise on Vref may not exceed ± 2 percent of the DC value. Thus, from 70% of VddQ, Vref is allowed ± 25mV for DC error
and an additional ± 25mV for AC noise.
7. Needed to further definitions.
8. Vid is the magnitude of the difference between the input level on CK and the input level on CK#.
9. The value of Vix is expected to equal 70 percent of VddQ for the transmitting device and must track variations in the DC level of
the same.
10. Idd is dependent on output loading and cycle rates. Specified values are obtained with minimum cycle time at minium CAS
latency and does not include the on-die termination current. Outputs are open during Idd measurements.
11. Enables on-chip refresh and address counters.
12. Idd specifications are tested after the device is properly initialized.
13. This parameter is sampled. Vdd = 1.8V, VddQ = 1.8V, Vref = Vss, f = 1 MHz, TA =25℃, Vout(DC) = 0.75V, VddQ,
Vout (peak to peak)= 0.2V. DM input is grouped with I/O pins, reflecting the fact that they are matched in loading.
14. Command/Address input slew rate = 3 V/ns. If the slew rate is less than 3 V/ns, timing is no longer referenced to the midpoint
but to the Vil(AC) maximum and Vih(AC) minimum points.
15. The CK/CK# input reference level (for timing referenced to CK/CK#) is the point at which CK and CK# cross; the input reference
level for signals other than CK/CK# is Vref.
16. Inputs are not recognized as valid until Vref stabilizes. Exception: during the period before Vref stabilizes, MF, CKE <= 0.3 x
VddQ is recognized as LOW.
17. Not used in this Specification.
18. tHZ and tLZ transitions occur in the same access time windows as valid data transitions. These parameters are not referenced to
a specific voltage level, but specify when the device output is no longer driving (HZ) or begins driving(LZ).
19. The maximum limit for this parameter is not a device limit. The device will operate with a greater value for this parameter, but
system performance(bus turn-around) will degrade accordingly.
20. This is not a device limit. The device will operate with a negative value, but system performance could be degraded due to bus
turnaround.
21. It is recommended that WDQS be valid (HIGH orLOW) on or before the WRITE command.
22. MIN (tRC or tRFC) for Idd measurements is the smallest multiple of tCK that meets the minimum absolute value for the respective
parameter. tRASMAX for Idd measurements is the largest multiple of tCK that meets the maximum absolute value for tRAS.
23. The refresh period is 8K every 32ms. This equates to an average refresh rate of 3.9us.
24. The I/O capacitance per DQS and DQ byte/group will not differ by more than this maximum amount for any given device.
25. The valid data window is derived by achieving other specifications . tDQHP and tDQSQ. The data valid window derates in direct
proportion to the strobe duty cycle and a practical data valid window can be derived. The strobe is allowed a maximum duty
cycle variation of 48:52. Functionality is uncertain when operating beyond a 48:52 ratio.
26. Referenced to each output group: RDQS0 with DQ0.DQ7, RDQS1 with DQ8.DQ15, RDQS2 with DQ16.DQ23, and RDQS with
DQ24.DQ31.
Rev.1.5 / Jul. 2008
53
H5RS5223CFR
27. This limit is actually a nominal value and does not result in a fail value. CKE is HIGH during REFRESH command period (tRFC
[MIN]) else CKE is LOW (e.g., during standby).
28. The DC values define where the input slew rate requirements are imposed, and the input signal must not violate these levels in
order to maintain a valid level. The inputs require the AC value to be achieved during signal transition edge, and the driver
should achieve the same slew rate through the AC values.
29. The input capacitance per pin group will not differ by more than this maximum amount for any given device.
30. CK and CK# input slew rate must be >= 3 V/ns.
31. DQ and DM input slew rates must not deviate from WDQS by more than 10 percent. If the DQ/DM/WDQS slew rate is less than 3
V/ns, timing is no longer referenced to the midpoint but to the Vil(AC) maximum and Vih(AC) minimum points.
32. Vdd must not vary more than 4 percent if CKE is not active while any bank is active.
33. The clock is allowed up to ± 90ps of jitter. Each timing parameter is allowed to vary by the same amount.
34. tHP (MIN) is the lesser of tDQSL minimum and tDQSH minimum actually applied to the device CK and CK# inputs, collectively
during bank active.
35. For READs and WRITEs with auto precharge the GDDR3 device will hold off the internal PRECHARGE command until tRAS (MIN)
has been satisfied.
36. The last rising edge of WDQS after the write postamble must be driven high by the controller.WDQS cannot be pulled high by the
on-die termination alone. For the read postamble the GDDR3 will drive the last rising edge of the read postamble.
37. The voltage levels used are derived from the referenced test load. In practice, the voltage levels obtained from a properly termi
nated bus will provide significantly different voltage values.
38. Vih overshoot: Vih (MAX) = VddQ + 0.5V for a pulse width <= 500ps and the pulse width cannot be greater than 1/3 of the cycle
rate. Vil under-shoot: Vil (MIN) = 0.0V for a pulse width <= 500ps and the pulse width cannot be greater than 1/3 ofthe cycle
rate.
39. The DLL must be reset when changing the frequency, followed by 5K clock cycles.
40. Junction temperature is a function of total device power dissipation and device mounting environment. Measured per SEMI G3887.
41. The thermal resistance data is based on a number of samples from multiple lots and should be viewed as a typical number. These
parameters are not tested in production or just guaranteed by the simulation methods.
42. The WRITE latency can be set from 1 to 6 clocks but can never be less than 2ns for latencies of 1 and 3clocks. When the WRITE
latency is set to 1 or 3 clocks,the input buffers are always on, reducing the latency but adding power. When the WRITE latency
is set to 4 or 6 clocks the input buffers are turned on during the WRITE commands for lower power operation and can never be
less than 7.5ns.
43. We’ll try to cut these values for positive timing budget of 800MHz operations
44. Minimum of +9 cycles are needed to Read commands.
45. 8 Banks device sequential bank activation restriction: No more than 4 banks may be activated in a rolling tFAW(Four actvite wind
ow). tFAW=4th Banks Act + tRRD*2=(tRRD*5). Converting to clocks is done by dividing tFAW by tCK and rounding up to next
integer.
46. In here, tRPRE means, Low drive period of RDQS prior to the valid high rising edge. It doesn't include the High drive period prior
to Low drive.
47. WR_A (write recovery time for autoprecharge) in clock cycles is calculated by dividing tWR (in nS) and rounding up to the next
integer (WR[cycles] = tWR(ns)/tCK(ns)). The mode register must be programmed to this value.
48. tCK_max = 3.3ns at CL7~10, tCK_max = 2ns at CL11
Rev.1.5 / Jul. 2008
54
H5RS5223CFR
Table 20: Electrical Characteristics Usages as Clock phase
-18C
AC Characteristics Parameter
-16(L)*
-14(L)
-20C
-12C*
-11C
-N0C
-N2C
-N3C
Unit
Symbol
MIN
MAX
MIN
MAX
MIN
MAX
Min
Max
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
tRAS
17
70Kns
19
70Kns
22
70Kns
15
70Kns
25
70Kns
28
70Kns
28
70Kns
28
70Kns
30
70Kns
tCK
tRC
24
-
28
-
31
-
22
-
35
-
40
-
39
-
39
-
42
-
tCK
tRFC
30
-
31
-
39
-
27
-
45
-
50
-
50
-
52
-
56
-
tCK
ACTIVE to READ delay
tRCDR
8
-
10
-
11
-
8
-
12
-
13
-
14
-
14
-
16
-
tCK
ACTIVE to WRITE delay
tRCDW
5
-
6
-
7
-
5
8
-
9
-
9
-
9
-
10
-
tCK
tRP
7
-
8
-
9
-
7
-
10
-
11
-
12
-
14
-
15
-
tCK
ACTIVE bank a
to ACTIVE bank b command
tRRD
5
-
6
-
7
-
5
-
8
-
9
-
9
-
9
-
10
-
tCK
Bank active restriction
rolling window
tFAW
28
-
32
-
35
-
25
-
40
-
44
-
48
-
48
-
48
-
tCK
Write recovery time
tWR
7
-
8
-
9
-
7
-
10
-
12
-
12
-
12
-
14
-
tCK
Internal WRITE to READ
command delay
tWTR
4
-
5
-
6
-
4
-
7
-
8
-
7
-
7
-
7
-
tCK
WRITE recovery time +
PRECHARGE command
period
tDAL
14
-
16
-
18
-
14
-
20
-
22
-
24
-
26
-
29
-
tCK
Exit SELF REFRESH to
READ command
tXSRD
5K
5K
-
5K
-
5K
-
5K
-
5K
-
tCK
Exit self refresh to
Non-Read command
tXSNR
300
300
-
300
-
300
-
300
-
300
-
tCK
Power-down exit time
tPDEX
4tCJK
+tIS
6tCJK
+tIS
-
7tCJK
+tIS
-
7tCJK
+tIS
-
7tCJK
+tIS
-
7tCJK
+tIS
-
tCK
Refresh interval time
tREF
-
-
3.9
-
3.9
-
3.9
-
3.9
-
3.9
us
Parameter
ACTIVE to PRECHARGE
command
ACTIVE to ACTIVE/AUTO
REFRESH command period
AUTO REFRESH
command period
PRECHARGE
command period
5K
-
300
5K
-
5tCJK
+tIS
3.9
-
300
5K
-
5tCJK
+tIS
3.9
-
300
-
4tCJK
+tIS
3.9
-
3.9
Note) *: 1. It’s only reference for customers who would like to use 700MHz(-14) part for 600MHz operation and
900MHz(-11) part of 800MHz operation and please use CL=8 for (-16) operation and CL=10 for (-12) operation.
2. ‘-18C/-14L’ means low voltage so its value is measured at 1.545max voltage.
3. H5RS5223CFR-20C/-14C/-11C is standardized by 1.9max voltage and H5RS5223CFR-N0C/-N2C/-N3C is standardized by 2.10max voltage.
Rev.1.5 / Jul. 2008
55
H5RS5223CFR
I/O and ODT Values
The Driver and Termination impedances are derived from the following test conditions under worst case process corners:
1. Nominal 1.8V (VDD/VDDQ)
2. Power the GDDR3 device and calibrate the output drivers and termination to eliminate process variation at 25℃.
3. Reduce temperature to 10℃ recalibrate.
4. Reduce temperature to 0℃ and take the fast corner measurement.
5. Raise temperature to 75℃ and recalibrate
6. Raise temperature to 85℃ and take the slow corner measurement
I/O Impedances
Pull-Down Characteristic at 40 ohms
Pull-Up Characteristic at 40ohms
Voltage (V)
MIN
MAX
Voltage (V)
MIN
MAX
0.1
2.144
3.366
0.1
-2.377
-2.946
0.2
4.268
6.516
0.2
-4.705
-5.829
0.3
6.373
9.454
0.3
-6.984
-8.644
0.4
8.449
12.185
0.4
-9.283
-11.383
0.5
10.505
14.715
0.5
-11.524
-14.038
0.6
12.542
17.051
0.6
-13.803
-16.599
0.7
14.540
19.400
0.7
-16.015
-19.051
0.8
16.509
21.828
0.8
-18.285
-21.630
0.9
18.449
24.219
0.9
-20.302
-24.143
1.0
20.341
26.580
1.0
-22.223
-26.605
1.1
22.203
28.913
1.1
-24.066
-29.005
1.2
24.017
31.222
1.2
-25.773
-31.353
1.3
25.783
33.508
1.3
-27.344
-33.619
1.4
27.480
35.813
1.4
-28.683
-35.803
1.5
29.119
38.213
1.5
-29.731
-37.883
1.6
30.671
40.551
1.6
-30.691
-39.882
1.7
31.387
42.900
1.7
-31.544
-42.003
1.8
31.648
45.176
1.8
-32.311
-44.063
Rev.1.5 / Jul. 2008
56
H5RS5223CFR
On Die Termination Values
Pull-Up Characteristic at 60ohms
Pull-Up Characteristic at 120ohms
Pull-Up Characteristic at 240ohms
Voltage (V)
MIN
MAX
Voltage (V)
MIN
MAX
Voltage (V)
MIN
MAX
0.1
-1.58
-1.96
0.1
-0.79
-0.98
0.1
-0.40
-0.49
0.2
-3.14
-3.89
0.2
-1.57
-1.94
0.2
-0.78
-0.97
0.3
-4.66
-5.76
0.3
-2.33
-2.88
0.3
-1.16
-1.44
0.4
-6.19
-7.59
0.4
-3.09
-3.79
0.4
-1.55
-1.90
0.5
-7.68
-9.36
0.5
-3.84
-4.68
0.5
-1.92
-2.34
0.6
-9.20
-11.07
0.6
-4.60
-5.53
0.6
-2.30
-2.77
0.7
-10.68
-12.70
0.7
-5.34
-6.35
0.7
-2.67
-3.18
0.8
-12.19
-14.42
0.8
-6.09
-7.21
0.8
-3.05
-3.60
0.9
-13.53
-16.10
0.9
-6.77
-8.05
0.9
-3.38
-4.02
-4.43
1.0
-14.82
-17.74
1.0
-7.41
-8.87
1.0
-3.70
1.1
-16.04
-19.34
1.1
-8.02
-9.67
1.1
-4.01
-4.83
1.2
-17.18
-20.90
1.2
-8.59
-10.45
1.2
-4.30
-5.23
1.3
-18.23
-22.41
1.3
-9.11
-11.21
1.3
-4.56
-5.60
1.4
-19.12
-23.87
1.4
-9.56
-11.93
1.4
-4.78
-5.97
1.5
-19.82
-25.26
1.5
-9.91
-12.63
1.5
-4.96
-6.31
1.6
-20.46
-26.59
1.6
-10.23
-13.29
1.6
-5.12
-6.65
1.7
-21.03
-28.00
1.7
-10.51
-14.00
1.7
-5.26
-7.00
1.8
-21.54
-29.38
1.8
-10.77
-14.69
1.8
-5.39
-7.34
Rev.1.5 / Jul. 2008
57
H5RS5223CFR
Figure 29: Data Output Timing - tDQSQ, tQH and Data Valid Window
NOTE:
1. tDQSQ represents the skew between the eight DQ lines and the respective RDQS pin.
2. tDQSQ is derived at each RDQS edge and is not cumulative over time and begins with first DQ transition and ends with the last
valid transition of DQ.
3. tAC is shown in the nominal case.
4. tDQHP is the lesser of tDQSL or tDQSH strobe transition collectively when a bank is active.
5. The data valid window is derived for each RDQS transitions and is defined by tDV.
6. There are four RDQS pins for this device with RDQS0 in relation to DQ(0.7), RDQS1 in relation DQ(8.15), RDQS2 in relation to
DQ(16.24), and RDQS3 in relation to DQ(25.31).
7. This diagram only represents one of the four byte lanes.
Rev.1.5 / Jul. 2008
58
H5RS5223CFR
Figure 30: Data Output Timing - AC
NOTE:
1. tAC represents the relationship between DQ, RDQS to the crossing of CK and CK#.
Figure 31: Data Input Timing
NOTE:
1. tDSH (MIN) generally occurs during tDQSS (MIN).
2. tDSS (MIN) generally occurs during tDQSS (MAX).
Rev.1.5 / Jul. 2008
59
H5RS5223CFR
Package Information
Pin A1 Mark
Pin A1 Mark
14
<Bottom View>
10
<Top View>
0.15+0.05
2-R0.13Max
0.8 X 11 = 8.8
0.8
1.1 + 0.1
0.34+0.05
2.0
12 11 10 9
4 3 2 1
0.8
0.8 x 16 = 12.8
0.45+0.05
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
2.0
0.6
0.10 Max
0.6
Unit:mm
Rev.1.5 / Jul. 2008
60
H5RS5223CFR
Appendix A
The following diagram shows the general GDDR3 driver and terminator
Self Calibration of Pmos Leg
Output Driver
Read to other
Rank
VDDQ
60 ohm
Terminator when
receiving
Output
Data
VDDQ
Strength control [2:0]
3
Read Data
Enable
DQ
Compaintor
240ohms
Match
VDDQ
VDDQ/2
40 ohm Driver
when transmitting
VSSQ
When Match Pmos leg is calibrated to 240 ohms
Self Calibration of Nmos Leg
Self Calibration flow for Driver and Terminator
First calibrate Pmos device against 240ohm resistor to
VSS via ZQ pin
This calibrate one Pmos leg to 240 ohms
Use 1 Pmos leg for 240 ohm terminator
Use 2 Pmos legs for 120 ohm terminator
Use 4 Pmos legs for 60 ohm terminator
Use 6 Pmos legs for 40 ohm pull up driver
Next calibrate one Nmos leg against the already calibrated 240 ohm Pmos leg
This calibrates one Nmos leg to 240 ohms
Use 6Nmos legs for 40 ohm driver
VDDQ
Compaintor
Match
Pulled Low to VSSQ
VDDQ/2
Strength control
[2:0]
3
VSSQ
When Match Nmos leg is calibrated to 240 ohms
Rev.1.5 / Jul. 2008
61
H5RS5223CFR
Apendix B Definition of Terminology
Hereafter are defined terminologies used in the GDDR3 SDRAM specification.
Although GDDR3 might be operated in ODT Disable Mode, it is not recommended and the specification describes the ODT Enable
Mode only. Should a system be designed to operate the GDDR3 in ODT Disable Mode, the system should comprehend the effect of
the discrepancies between this specification and its own design.
If it is stated that a bus is in one of the following state, it should be interpreted as described.
Following are three terminologies defined for ODT Enable Mode.
- High{terminated}: A driver on the bus is driving the bus. One or more termination (ODT) on the bus is turned-on.
The voltage level of the bus would be nominally VDDQ.
- Hi-z{terminated}: No driver on the bus is driving the bus. One or more termination (ODT) on the bus is turned-on.
The voltage level of the bus would be nominally VDDQ.
- Low{terminated}: A driver on the bus is driving the bus. One or more termination (ODT) on the bus is turned-on.
The voltage level of the bus would be nominally VOL(DC).
Corresponding terminologies for ODT Disable Mode are defined below.
As mentioned before, ODT Disable Mode is not an intended mode of operation. However, there exist situations where ODT Enable
Mode can not be guaranteed for a short period of time, like during power up, yet is indeed an intended mode of operation.
- High{unterminated}: A driver on the bus is driving the bus. No termination on the bus is active.
The voltage level of the bus would be nominally VDDQ.
- Hi-z{unterminated}: No driver on the bus is driving the bus. No termination on the bus is active.
The voltage level of the bus would be undefined, because the bus would be floating.
- Low{unterminated}: A driver on the bus is driving the bus. No termination on the bus is active.
The voltage level of the bus would be nominally VSSQ.
Rev.1.5 / Jul. 2008
62
H5RS5223CFR
APPENDIX C Boundary Scan Test Mode
General Information
The 512Mb GDDR3 incorporates a modified boundary scan test mode as an optional feature. This mode doesn’t operate in accordance with IEEE Standard 1149.11990. To save the current GDDR3 ballout, this mode will scan the parallel data input and output the
scanned data through WDQS0 pin controlled by an addon pin, SEN which is located at V4 of 136 ball package.
Disabling the Scan feature
It is possible to operate the 512Mb GDDR3 without using the boundary scan feature. SEN(at V4 of 136ball package) should be tied
LOW(VSS) to prevent the device from entering the boundary scan mode. The other pins which are used for scan mode, RES, MF,
WDQS0 and CS# will be operating at normal GDDR3 functionalities when SEN is deasserted.
Figure C-1: Internal Block Diagram(Reference Only)
Rev.1.5 / Jul. 2008
63
H5RS5223CFR
Table C-1: Boundary Scan (Exit) Order
BIT#
BALL
PIN
BIT#
BALL
PIN
BIT#
BALL
PIN
BIT#
BALL
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
D-3
C-2
C-3
B-2
B-3
A-4
B-10
B-11
C-10
C-11
D-10
D-11
E-10
F-10
E-11
G-10
F-11
RDQ0
DQ2
DQ3
DQ0
DQ1
ZQ
DQ9
DQ8
DQ11
DQ10
RDQ1
WDQS1
DM1
DQ13
DQ12
DQ15
DQ14
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
G-9
H-9
H-10
H-11
J-11
J-10
L-9
K-11
K-10
K-9
M-9
M-11
L-10
N-11
M-10
N-10
P-11
BA1
WE#
BA2
A5
CK
CK#
A7
A8
A6
A4
A9
DQ16
DQ17
DQ18
DQ19
DM2
WDQS2
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
P-10
R-11
R-10
T-11
T-10
T-3
T-2
R-3
R-2
P-3
P-2
N-3
M-3
N-2
L-3
M-2
M-4
RDQS2
DQ20
DQ21
DQ22
DQ23
DQ31
DQ30
DQ29
DQ28
RDQS3
WDQS3
DM3
DQ27
DQ26
DQ25
DQ24
A3
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
K4
K-3
K-2
L-4
J-3
J-2
H-2
H-3
H-4
G-4
F-4
F-2
G-3
E-2
F-3
E-3
A0
A2
A10
A11
RFU2
RFU1
A1
RAS#
CKE
BA0
CAS#
DQ6
DQ7
DQ4
DQ5
DM0
Note:
1. When the device is in scan mode, the mirror function will be disabled and none of the pins are remapped.
2. Since the other input of the MUX for DM0 tied to GND, the device will output the continuous zeros after scanning a bit #67, if the
chip stays in scan shift mode.
3. Two RFU balls (#56 and #57) in the scan order, will read as a logic“0”.
Table C-2: Scan Pin Descriptions
BALL
SYMBOL
Normal
Funtion
Type
U-9
SSH
RES
Input
F-9
SCK
CS#
Input
D-2
SOUT
WDQS0
Output
U-4
SEN
RFU
Input
A-9
SOE#
MF
Input
Descriptions
Scan Shift.
Capture the data input from the pad at logic LOW and shift the data on the chain at logic
HIGH.
Scan Clock.
Not a true clock, could be a single pulse or series of pulses. All scan inputs will be referenced to rising edge of the scan clock.
Scan Output.
Scan Enable.
Logic HIGH would enable the device into scan mode and will be disabled at logic LOW.
Must be tied to GND when not in use.
Scan Output Enable.
Enables (registered LOW) and disables (registered HIGH) SOUT data. This pin will be
tied to VDD or GND through a resistor (typically 1K) for normal operation. Tester needs
to overdrive this pin to guarantee the required input logic level in scan mode.
Note:
1. When SEN is asserted, no commands are to be executed by the GDDR3. This applies both to user commands and manufacturing
commands which may exist while RES is deasserted.
2. All scan functionalities are valid only after the appropriate power-up and initialization sequence. (RES and CKE, to set the ODT of
the C/A)
3. In scan mode, the ODT for the address and control lines set to a nominal termination value of ZQ. The ODT for DQ’s will be dis
abled. It is not necessary for the termination to be calibrated.
4. During the power-up and initialization sequence, ZQ pin should be maintained the connection to VSSQ through proper RQ.
5. In a double-load clam-shell configuration, SEN will be asserted to both devices. Separate two SOE#’s should be provided to top
and bottom devices to access the scanned output. When either of the devices is in scan mode, SOE# for the other device which is
not in a scan will be disabled.
Rev.1.5 / Jul. 2008
64
H5RS5223CFR
Table C-3: Scna DC Electrical Characteristics and Operating Conditions
Parameter/Conditionss
Symbol
MIN
MAX
Units
Input High(Logic 1) Voltage
VIH(DC)
VREF+0.15
-
V
Input Low(Logic 0) Voltage
VIL(DC)
-
VREF-0.15
V
Note:
1. The parameter applies only when SEN is asserted.
2. All voltages referenced to GND.
Figure C-2: Scan Capture Timing
N o t a tr u e c l o c k, b u t a si n l g e p u l s e o r s e ri e s o f p u l s e s
SCK
tSES
SEN
SSH
tSCS
SOE#
tSDS tSDH
Pins
under Test
VALID
DON’T CARE
Figure C-3: Scan Shift Timing
SCK
tSES
SEN
tSCS
SSH
tSCS
SOE#
Scan Out
bit 0
SOUT
tSAC
Rev.1.5 / Jul. 2008
tSOH
Scan Out
bit 1
Scan Out
bit 2
Scan Out
bit 3
Transitioning Data
65
H5RS5223CFR
Table C-4: Scan AC Electrical Charateristics
Parameters/Conditions
SYMBOL
MIN
MAX
UNITS
NOTE
tSCK
40
-
nS
1
Scan enable setup time
tSES
20
-
nS
1,2
Scan enable hold time
tSEH
20
-
nS
1
Scan command setup time for SSH, SOE# and SOUT
tSCS
14
-
nS
1
Scan command hold time for SSH, SOE# and SOUT
tSCH
14
-
nS
1
Clock
Clock Cycle time
Scan Command Time
Scan Capture Time
Scan capture setup time
tSDS
10
-
nS
1
Scan capture hold time
tSDH
10
-
nS
1
Scan Shift Time
Scan clock to valid scan output
tSAC
-
6
nS
1
Scan clock to scan output hold
tSOH
1.5
-
nS
1
Note:
1. The parameter applies only when SEN is asserted.
2. Scan Enable should be issued earlier than other Scan Commands by 10nS.
Figure C-4: Scan Initialization Sequence
VDD
VDDQ
VREF
RES
(SSH)
tSCS
tATS tATH
tSCH
tSDS
tSDH
tSCS
tSCH tSCH
VALID
CKE
SEN
tSES
SCK
tSCS
SOE#
tSCS
SOUT
tSDS
tSDH
VALID
PUT
T=200µS
Power-up:
VDD Stable
T=200µS
RESET at Power-up
Boundary Scan Test Mode
DON’T CARE
Note:
To set the pre-defined ODT for C/A, a boundary scan mode should be issued after an appropriate ODT initialization sequence with
RES and CKE signals
Rev.1.5 / Jul. 2008
66