Radial Lead Resettable Polymer PTCs JK130 Series Description JK135 Series is designed to protect against short duration high voltage fault currents (power cross or power induction surge) typically used in AC110V. Features u u u u 0.05-3.5A hold current rating 135VAC operating voltage Fast time-to- trip RoHS compliant, Lead-Free and Halogen-Free Applicable u u u AC110V over-current protection Power ports Customer Premises Equipment(CPE) Electrical Parameters I trip (A) V max (Vac) I max (A) P dtyp. (W) Maximum Time To Trip Current Time (A) (Sec.) 0.5 6.0 Resistance Part Number I hold (A) JK130-010 0.1 0.20 130 10.0 0.8 JK130-015 0.15 0.30 130 10.0 0.8 0.75 JK130-017 0.17 0.34 130 100 0.8 0.85 JK130-020 0.20 0.40 130 10.0 0.8 1.00 JK130-025 0.25 0.50 130 10.0 1.0 1.25 4.8 JK130-030 0.30 0.60 130 10.0 1.0 1.50 4.5 JK130-040 0.40 0.80 130 10.0 1.0 2.00 4.5 0.75 2.0 4.0 JK130-050 0.50 1.00 130 10.0 1.0 2.50 5.0 0.50 1.60 3.5 JK130-065 0.65 1.30 130 10.0 1.0 3.25 5.2 0.45 1.00 2.0 JK130-075 0.75 1.50 130 10.0 1.0 3.75 5.5 0.40 0.90 2.0 JK130-090 0.90 1.80 130 10.0 1.5 4.50 5.8 0.30 0.70 1.5 1.20 R min (Ω) 2.50 R max (Ω) 9.0 R 1max (Ω) 20.0 5.5 2.50 7.5 18.0 5.2 1.50 7.0 16.0 5.0 1.90 4.0 12.0 1.45 3.5 10.0 1.00 3.0 5.0 JK130-110 1.10 2.20 130 10.0 1.5 5.5 6.3 0.20 0.65 JK130-135 1.35 2.70 130 10.0 1.8 6.75 7.5 0.15 0.60 1.1 JK130-160 1.60 3.20 130 10.0 1.8 8.00 8.0 0.10 0.50 1.00 JK130-185 1.85 3.70 130 10.0 2.0 9.25 9.0 0.10 0.40 0.80 JK130-200 2.00 4.0 130 10.0 2.0 10.00 10.0 I hold= Hold current: maximum current device will pass without tripping in 25°C still air. I trip= Trip current: minimum current at which the device will trip in 25°C still air. V max= Maximum voltage device can withstand without damage at rated current (Imax) I max= Maximum fault current device can withstand without damage at rated voltage (Vmax) Pdtyp.= Power dissipated from device when in the tripped state at 25°C still air. R min= Minimum resistance of device in initial (un-soldered) state. R max= Maximum resistance of device in initial (un-soldered) state. R 1max= Maximum resistance of device at 25°C measured one hour after tripping. Caution: Operation beyond the specified rating may result in damage and possible arcing and flame. 0.10 0.30 0.50 UN Semiconductor Co., Ltd. Revision October 18, 2013 www.unsemi.com.tw 1/4 @ UN Semiconductor Co., Ltd. 2013 Specifications are subject to change without notice. Please refer to www.unsemi.com.tw for current information. Radial Lead Resettable Polymer PTCs JK130 Series 0.40 Temperature Rerating Chart – I hold (A) Ambient Operation Temperature Part Number -40°C -20°C 0°C 25°C 40°C 50°C 60°C 70°C 85°C Hold Current (A) JK130-010 0.16 0.14 0.12 0.10 0.08 0.07 0.06 0.05 0.04 JK130-015 0.24 0.21 0.18 0.15 0.12 0.11 0.09 0.08 0.06 JK130-017 0.27 0.23 0.20 0.17 0.14 0.12 0.11 0.09 0.07 JK130-020 0.31 0.27 0.24 0.20 0.16 0.14 0.13 0.11 0.08 JK130-025 0.39 0.34 0.30 0.25 0.21 0.18 0.16 0.14 0.10 JK130-030 0.47 0.41 0.36 0.30 0.25 0.22 0.19 0.16 0.12 JK130-040 0.62 0.55 0.48 0.40 0.33 0.29 0.25 0.22 0.16 JK130-050 0.78 0.69 0.60 0.50 0.41 0.36 0.32 0.27 0.21 JK130-065 1.01 0.89 0.77 0.65 0.53 0.47 0.41 0.35 0.27 JK130-075 1.17 1.03 0.89 0.75 0.62 0.54 0.47 0.41 0.31 JK130-090 1.40 1.23 1.07 0.90 0.74 0.65 0.57 0.49 0.37 JK130-110 1.71 1.51 1.31 1.10 0.90 0.79 0.69 0.59 0.45 JK130-135 2.09 1.85 1.61 1.35 1.11 0.97 0.85 0.73 0.55 JK135-160 2.48 2.18 1.90 1.60 1.30 1.15 1.01 0.86 0.64 JK135-185 2.87 2.52 2.20 1.85 1.50 1.33 1.17 1.00 0.74 JK135-200 3.10 2.72 2.38 2.00 1.62 1.44 1.26 1.08 0.80 Temperature Rerating Curve Time in Seconds Percentage of Rated Current Average Time Current Curves Temperature (°C) Current in Amperes UN Semiconductor Co., Ltd. Revision October 18, 2013 www.unsemi.com.tw 2/4 @ UN Semiconductor Co., Ltd. 2013 Specifications are subject to change without notice. Please refer to www.unsemi.com.tw for current information. Radial Lead Resettable Polymer PTCs JK130 Series Test Procedures and Requirement Test Test Conditions Accept/Reject Criteria Resistance In still air @25±2°C Rmin≤R≤Rmax Hold Current 60 min, at Ihold, In still air @25±2°C No trip Time to Trip Specified current, Vmax, @25±2°C T≤Maximum Time To Trip Trip Cycle Life Vmax, Imax,100 cycles No arcing or burning Trip Endurance Vmax,24hours No arcing or burning Soldering Parameters Pre-Heating Zone Refer to the condition recommended by the manufacturer. Max. ramping rate should not exceed 4°C/Sec Soldering Zone Max. solder temperature should not exceed 260°C Cooling Zone Cooling by natural convection in air Physical Specifications Lead Material Soldering Characteristics Insulating Material Device Labeling 0.1-0.17A Tin-plated Copper clad steel 0.2-2. 0A Tin-plated Copper Solder ability per MIL-STD-202, Method 208E Cured, flame retardant epoxy polymer meets UL 94V-0 requirements. Marked with ‘UN’, voltage, current rating Part Marking Part Numbering UN Semiconductor Co., Ltd. Revision October 18, 2013 www.unsemi.com.tw 3/4 @ UN Semiconductor Co., Ltd. 2013 Specifications are subject to change without notice. Please refer to www.unsemi.com.tw for current information. Radial Lead Resettable Polymer PTCs JK130 Series Dimensions Figure1 A B Figure2 C D Lead (dia) Part Number Figure mm (Max.) mm (Max.) mm (Typ.) mm (Max.) Inches mm Packaging (Bulk Pack) JK130-010 Figure1 7.4 12.7 5.1 3.1 0.020 0.5 1000 JK130-015 Figure1 7.4 13.0 5.1 3.1 0.020 0.5 1000 JK130-017 Figure1 7.4 13.5 5.1 3.1 0.020 0.5 1000 JK130-020 Figure1 7.6 13.5 5.1 3.1 0.020 0.5 1000 JK130-025 Figure1 7.6 13.5 5.1 3.1 0.020 0.5 1000 JK130-030 Figure1 8.0 14.0 5.1 3.1 0.020 0.5 1000 JK130-040 Figure1 9.4 15.0 5.1 3.1 0.020 0.5 1000 JK130-050 Figure1 10.2 15.2 5.1 3.1 0.024 0.6 1000 JK130-065 Figure1 10.2 15.2 5.1 3.1 0.024 0.6 1000 JK130-075 Figure1 12.8 18.0 5.1 3.1 0.024 0.6 1000 JK130-090 Figure1 14.5 19.6 5.1 3.1 0.031 0.8 1000 JK130-110 Figure2 16.3 21.3 5.1 3.1 0.031 0.8 1000 JK130-135 Figure2 17.0 22.0 5.1 3.1 0.031 0.8 1000 JK130-160 Figure2 18.0 23.0 5.1 3.1 0.031 0.8 1000 JK130-185 Figure2 22.0 23.0 5.1 3.1 0.031 0.8 500 JK130-200 Figure2 22.0 27.0 10.2 3.1 0.031 0.8 500 Warning u This product should not be used in an application where the maximum interrupt voltage or maximum interrupt current in a fault condition, Operation beyond the maximum rating or improper use may result in device damage and possible electrical arcing and flame. u A PPTC device is not a fuse, It is a nonlinear thermistor that limits current, Because under a fault condition all PPTC devices go into a high resistance state but not open circuit hazardous voltage may be present at PPTC. u The devices are intended for protection against occasional over-current or over-temperature fault conditions and should not be used when repeated fault conditions or prolonged trip events. u In most application, power must be removed and the fault condition cleared in order to reset a PPTC device. u PPTC devices are not recommended to be installed in applications where the device is constrained such that its PPTC properties are inhibited, for example in rigid potting materials or Add devices surface coating, Bundled devices ontology, which lack adequate clearance to accommodate device expansion. u Contamination on of the PPTC material with certain silicone-based oils or some aggressive solvents can adversely impact the performance of the devices. For example, Organic solvents to cleaning. UN Semiconductor Co., Ltd. Revision October 18, 2013 www.unsemi.com.tw 4/4 @ UN Semiconductor Co., Ltd. 2013 Specifications are subject to change without notice. Please refer to www.unsemi.com.tw for current information.