Film Capacitors EMI Suppression Capacitors (MKP) Series/Type: Date: B81122 August 2004 © EPCOS AG 2004. Reproduction, publication and dissemination of this data sheet, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry recommended by the ZVEI (German Electrical and Electronic Manufacturers' Association), unless otherwise agreed. EMI suppression capacitors (MKP) B81122 Y2 / 250 VAC Typical applications Y2 class for interference suppression "Line to ground" applications Dimensional drawing Climatic Max. operating temperature: 100 °C Climatic category (IEC 60068-1): 40/100/21 = 10 mm 40/085/21 ≥ 15 mm Construction Dielectric: polypropylene (MKP) Internal series connection (for Plastic case (UL 94 V-0) Epoxy resin sealing (UL 94 V-0) Dimensions in mm ≥15 mm) Lead spacing ±0.4 Lead diameter d1 Features Very small dimensions Self-healing properties 10 mm 15 ... 27.5 mm 0.6 0.8 Terminals Parallel wire leads, lead-free tinned Standard lead lengths: 6 1 mm Special lead lengths available on request Marking example Marking Manufacturer's logo, lot number, date code, rated capacitance (coded), cap. tolerance (code letter), rated AC voltage, series number, sub-class (Y2), dielectric code (MKP), climatic category, passive flammability category, approvals. Delivery mode Bulk (untaped) Taped (Ammo pack or reel) For taping details, refer to chapter "Taping and packing". Approvals Marks of conformity Standards EN 132400, IEC 60384-14 UL 1414 CSA C22.2 No.1 2 Certificate 138600 ( 138603 ( E97863 E97863 = 10 mm) ≥ 15 mm) B81122 Y2 / 250 VAC Overview of available types Lead spacing 10 mm 15 mm 22.5 mm CR (µF) 0.0010 0.0015 0.0022 0.0033 0.0047 0.0056 0.0068 0.010 0.015 0.022 0.027 0.033 0.047 0.056 0.068 0.10 0.15 0.22 0.33 3 27.5 mm B81122 Y2 / 250 VAC Ordering codes and packing units Lead spacing CR mm 10 15 22.5 27.5 µF 0.0010 0.0015 0.0022 0.0033 0.0047 0.0056 0.0068 0.010 0.015 0.022 0.027 0.033 0.047 0.056 0.068 0.10 0.15 0.22 0.33 Max. dimensions w×h×l mm 4.0 × 9.0 × 13.0 4.0 × 9.0 × 13.0 5.0 × 11.0 × 13.0 5.0 × 11.0 × 13.0 6.0 × 12.0 × 13.0 6.0 × 12.0 × 13.0 6.0 × 12.0 × 13.0 6.0 × 11.0 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 7.0 × 16.0 × 26.5 8.5 × 16.5 × 26.5 10.5 × 16.5 × 26.5 10.5 × 20.5 × 26.5 11.0 × 21.0 × 31.5 13.5 × 23.0 × 31.5 18.0 × 27.5 × 31.5 Ordering code (composition see below) B81122C1102M*** B81122C1152M*** B81122C1222M*** B81122C1332M*** B81122C1472M*** B81122C1562M*** B81122C1682M*** B81122A1103M*** B81122A1153M*** B81122A1223M*** B81122A1273M*** B81122A1333M*** B81122A1473M*** B81122A1563M*** B81122A1683M*** B81122A1104M*** B81122A1154M*** B81122A1224M*** B81122A1334M*** Ammo Reel Untaped pack pcs./unit pcs./unit pcs./unit 1000 1000 830 830 680 680 680 960 830 680 680 640 580 480 390 390 1700 1700 1300 1300 1100 1100 1100 1100 900 700 700 700 600 500 400 400 350 250 Further E series and intermediate capacitance values on request. Composition of ordering code + = Capacitance tolerance code: M = ±20% *** = Packaging code: 289 = Ammo pack 189 = Reel 000 = Untaped (lead length 6 1 mm) 4 1000 1000 1000 1000 1000 1000 1000 1000 1000 500 500 500 630 510 540 540 320 260 200 B81122 Y2 / 250 VAC Technical data Max. operating temperature Top,max +100 °C Dissipation factor tan δ (in 10-3) at 20 °C (upper limit values) at Insulation resistance Rins or time constant τ = CR Rins at 20 °C, rel. humidity ≤ 65% (minimum as-delivered values) DC test voltage Passive flammability category to IEC 40 (CO) 752 1 kHz 100 kHz 30 000 MΩ CR ≤ 0.1 µF CR >0.1 µF 1.0 1.0 5.0 2700 V, 2 s ( ≥ 15 mm) 2500 V, 2 s ( = 10 mm) C Maximum continuous AC voltage (V AC) 405 V (50/60 Hz) ( 305 V (50/60 Hz) ( ≥ 15 mm) = 10 mm) Rated AC voltage (IEC 60384-14) 250 V (50/60 Hz) ≥ 15 mm) Maximum continuous DC voltage (V DC) 1000 V ( 1200 V ( = 10 mm) Operating AC voltage V op at high temperature TA ≤ 100 °C Vop = VAC TA ≤ 100 °C Vop = 1.25 VAC Damp heat test Limit values after damp heat test 21 days / 40 °C / 93% relative humidity Capacitance change ∆C/C ≤ 5% Dissipation factor change ∆ tan δ ≤ 0.5 10-3 (at 1 kHz) Insulation resistance Rins ≤ 1.0 10-3 (at 10 kHz) or time constant τ = CR Rins ≥ 50% of minimum as-delivered values 5 (continuously) (1000 h) B81122 Y2 / 250 VAC Pulse handling capability "dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal voltages, expressed in V/µs. "k0" represents the maximum permissible pulse characteristic of the waveform applied to the capacitor, expressed in V 2/µs. Note: The values of dV/dt and k0 provided below must not be exceeded in order to avoid damaging the capacitor. dV/dt and k0 values Lead spacing dV/dt in V/µs k0 in V2/µs 10 mm 15 mm 550 388 000 400 282 000 6 22.5 mm 200 141 000 27.5 mm 150 106 000 B81122 Y2 / 250 VAC Impedance Z versus frequency f (typical values) Lead spacing = 10 mm Lead spacing ≥15 mm 7