6.2007 LCD GRAPHIC 122x32 INCL. CONTROLLER FOR 8 BIT BUS blue-white: EA DIP122B-5NLW Dimension 75 x 27 mm amber: EA DIP122J-5NLA Dimension 75 x 27 mm ting n u mo d e r mo quire no re yellow/green: EA DIP122-5HNLED Dimension 68 x 27 mm FEATURES * * * * * * * * * HIGH CONTRAST LCD DISPLAY AS STN AND FSTN CLASSIC LINE YELLOW/GREEN: EA DIP122-5HNLED OR BLUE-WHITE EA DIP122B-5NLW BUILT IN CONTROLLER PT6520 OR COMPATIBLE INTERFACE FOR 8 BIT DATA BUS POWER SUPPLY +2.7~5V / -6.3~-4V 800µA max. LED BACKLIGHT Y/G max. 150mA@+25°C LED BACKLIGHT AMBER AND WHITE max. 45mA@+25°C SOME MORE MODULES WITH SAME MECHANIC AND SAME PINOUT: DOTMATRIX 1x8, 2x16, 4x20 AND 128x64, 240x128 WITH LARGER OUTLINE * NO SCREWS REQUIRED: SOLDER ON IN PCB ONLY * DETACHABLE VIA 9-PIN SOCKET EA B200-9 (2 PCS. REQUIRED) * OPERATING TEMPERATURE RANGE 0~+50°C OR * -20~+70°C OPERATING TEMP. WITH BUILT-IN TEMP. COMP. CIRCUIT ORDERING INFORMATION LCD GRAPHIC MODULE 122x32, WITH BACKLIGHT Y/G Y/G FOR -20~+70°C OPERATING TEMP. RANGE BLUE-WHITE FOR -20~+70°C, LOW POWER AMBER FOR -20~+70°C 9-PIN SOCKET, HEIGHT 4.3mm (2 PCS. REQUIRED) HIGH-LEVEL-GRAPHICSCONTROLLER WITH RS-232C EA DIP122-5NLED EA DIP122-5HNLED EA DIP122B-5NLW EA DIP122J-5NLA EA B200-9 EA IC1520-1PGH Lochhamer Schlag 17 · D-82166 Graefelfing · Phone +49-(0)89-8541991 · Fax +49-(0)89-8541721 · www.lcd-module.de · [email protected] Specifications may be changed without prior notice. Printing error reserved EA DIP122-5 Page 2 PINOUT Pin Symbol Level Function Pin Symbol Level Function 1 VSS L Power supply 0V (GND) 10 D3 H/L Display Data 2 VDD H Power supply +5V 11 D4 H/L Display Data 3 VEE - Contrast adjustment (-4 V) 12 D5 H/L Display Data 4 A0 H/L Command / Data 13 D6 H/L Display Data 5 R/W H/L H=Read, L=Write 14 D7 H/L Display Data, MSB 6 E1 H Enable left side 15 E2 H Enable right side 7 D0 H/L Display Data, LSB 16 RES L Reset 8 D1 H/L Display Data 17 A - LED Backlit+ (external RV !) 9 D2 H/L Display Data 18 C - LED Backlit - CONTROLLER PT6520 Graphic modules of EA DIP122-5 series do have 2 controller PT6520 (or compatible) built in: One for the left half of display and the other for the right one. From 61 columns each 0..60 are used only. PT6520 do not have any character mode, so all character has ATTENTION to be set by graphic. Many different fonts are optionally available on disk with part numer EA DISKFONT1520. A detailed description for all commands and interface timing handling precautions! you will find at the user manual for PT6520*). Code Function A0 RD WR D7 D6 D5 D4 D3 D2 D1 D0 Display ON/OFF 0 1 0 1 0 1 0 Display start line 0 1 0 1 1 0 Display start address (0 - 31) Set page address 0 1 0 1 0 1 1 Set Column address 0 1 0 0 Column address (0 - 79) B U S Y A D C O N / O F F R E S E T 1 1 1 0 1 0/1 Turns Display on or off. 0=OFF; 1=ON; Specifies RAM line corresponding to top of display. Page Sets display RAM page. (0-3) Sets display RAM column address. Read the following status: 0 1=Busy; 1=CW output; 1=Display off; 1=Being reset; 0=Ready; 0=CCW output; 0=Display on; 0=Normal; 0 0 1 Write display data 1 1 0 Write data Writes data into display RAM. Read display data 1 0 1 Read data Reads data from display RAM. Select ADC 0 1 0 1 0 1 0 0 0 0 0/1 0=CW output; 1=CCW output; Static drive ON/OFF 0 1 0 1 0 1 0 0 1 0 0/1 Select duty 0 1 0 1 0 1 0 1 0 0 0/1 Select duty cycle. 0=1/16; 1=1/32; Read-Modify-Write 0 1 0 1 1 1 0 0 0 0 0 Read-modify-write ON End 0 1 0 1 1 1 0 1 1 1 0 Read-modify-write OFF Reset 0 1 0 1 1 1 0 0 0 1 0 Software reset. 0 0 BUSY: 0 ADC: ON/OFF: RESET: Read Status Selects static driving operation. 0=Normal driving; 1=Static drive; *) http://www.lcd-module.de/eng/pdf/zubehoer/pt6520.pdf Instructions Specifications may be changed without prior notice. Printing error reserved EA DIP122-5 Page 3 CONTRAST ADJUSTMENT Contrast voltage for all displays of EA DIP122-5 series is typ. -4V. That means that for 5V power supply an additional negative voltage of min. 4V is required. Display modules for -20..+70°C (-5HNLED, -5NLW and -5NLA) are equipped with an on-board temperature compensation. So there's no more need for contrast adjustment while operation anymore. Furthermore these 3 displays are featured with a superfast STN/FSTN liquid that allows fast resonse even at very low temperatures: typical response time at -20°C is 2 seconds only. BACKLIGHT Driving the backlight requires a current source or an external resistor for current limit. Please take care of derating for ta >+25°C. Uf for yellow/green backlight is 3.9~4.2V, 2.2~2.6V (amber) and 3.0~3.6V for white LED backlight. Note: Do never drive backlight direct to 5V; immediately damage my happen ! YELLOW/GREEN - BLUE - AMBER The blue-white display EA DIP122B-5NLW is best for indoor use with and without ambient light. Reading the display requires a minimum of backlight with about 15mA. The yellow/green version EA DIP122-5NLED is especially designed for 24-hour or outdoor applications. These displays do provide best contrast for all ambient illuminations, even with direct sunlight. No need to say that these display can be read in darkness when LED backlight is switched on. This is same for the amber backlighted version EA DIP122J-5NLA. EA DIP122-5 Specifications may be changed without prior notice. Printing error reserved handling precautions! ATTENTION DIMENSIONS all dimensions are in mm Note: In general LC display are not suitable for wave soldering and reflow soldering process. An ambient temperature above 80°C may destroy the display. Page 4 Lochhamer Schlag 17 · D-82166 Graefelfing · Phone +49-(0)89-8541991 · Fax +49-(0)89-8541721 · www.lcd-module.de · [email protected] Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: ELECTRONIC ASSEMBLY: EA DIP122-5NLED EA DIP122J-5NLE EA DIP122B-5NLW EA DIP122J-5NLA EA DIP122-5HNLED