plerowTM ALE3276T2 Internally Matched LNA Module Features Description · S21 = 19.7 dB@3050 MHz = 18.3 dB@3500 MHz · NF of 1.20 dB over Frequency · Unconditionally Stable · Single 5 V Supply · High OIP3@Low Current The plerowTM ALE-series is the compactly designed surface-mount module for the use of the LNA with or without the following gain blocks in the infrastructure equipment of the mobile wireless (CDMA, GSM, PCS, PHS, WCDMA, DMB, WLAN, WiBro, WiMAX), GPS, satellite communication terminals, CATV and so on. It has an exceptional performance of low noise figure, high gain, high OIP3, and low bias current. The stability factor is always kept more than unity over the application band in order to ensure its unconditionally stable implementation to the application system environment. The surface-mount module package including the completed matching circuit and other components necessary just in case allows very simple and convenient implementation onto the system board in mass production level. Specifications (in Production) Typ.@T = 25 °C, Vs = 5 V, Freq. = 3275 MHz, Zo.sys = 50 ohms Parameter Unit Frequency Range Min MHz 3050 Gain dB 18.0 Gain Flatness dB Noise Figure dB Output IP3 (1) dBm S11/S22 (2) Typ dBm Switching Time (3) Max 3500 19.0 35 ±0.7 ±0.8 1.20 1.25 More Information Website: www.asb.co.kr E-mail: [email protected] 36 dB Output P1dB 2-stage Single Type Specifications Tel: (82) 42-528-7223 Fax: (82) 42-528-7222 -12/-12 22 23 msec - Supply Current mA 200 Supply Voltage V 5 Impedance W 50 220 Max. RF Input Power dBm C.W 29~31 (before fail) Package Type & Size mm Surface Mount Type, 10Wx10Lx3.8H Operating temperature is -40 °C to +85 °C. 1) OIP3 is measured with two tones at an output power of 7 dBm/tone separated by 1 MHz. 2) S11, S22 (max) is the worst value within the frequency band. 3) Switching time means the time that takes for output power to get stabilized to its final level after switching DC voltage from 0 V to VS. Outline Drawing (Unit: mm) plerow ALE3276T2 ASB Inc. (Top View) (Bottom View) Pin Number Function 2 RF In 5 RF Out 6 Vs Others Ground Note: 1. The number and size of ground via holes in a circuit board is critical for thermal RF grounding considerations. 2. We recommend that the ground via holes be placed on the bottom of all ground pins for better RF and thermal performance, as shown in the drawing at the left side. Solder Stencil Area (Side View) Ø0.4 plated thru holes to ground plane (Recommended Footprint) 1/3 www.asb.co.kr July 2010 plerowTM ALE3276T2 Internally Matched LNA Module S-parameters Typical Performance (Measured) 3050~3500 MHz +5 V Noise Figure S-parameters & K Factor OIP3 2/3 P1dB www.asb.co.kr July 2010 plerowTM ALE3276T2 Internally Matched LNA Module Application Circuit VS + - Tantal or MLC (Multi Layer Ceramic) Capacitor C1 C2 ALN IN OUT 1) The tantal or MLC (Multi Layer Ceramic) capacitor is optional and for bypassing the AC noise introduced from the DC supply. The capacitance value may be determined by customer’s DC supply status. The capacitor should be placed as close as possible to Vs pin and be connected directly to the ground plane for the best electrical performance. 2) DC blocking capacitors are always necessarily placed at the input and output port for allowing only the RF signal to pass and blocking the DC component in the signal. The DC blocking capacitors are included inside the ALN module. Therefore, C1 & C2 capacitors may not be necessary, but can be added just in case that the customer wants. The value of C1 & C2 is determined by considering the application frequency. Recommended Soldering Reflow Process Evaluation Board Layout Vs 20~40 sec 260 °C Ramp-up (3 °C/sec) 200 °C Ramp-down (6 °C/sec) OUT IN 150 °C 60~180 sec 3/3 Size 25x25 mm (for ALE-T Series – 10x10 mm) www.asb.co.kr July 2010