SG7800A/SG7800 SERIES SG7800A/SG7800 POSITIVE FIXED VOLTAGE REGULATOR DESCRIPTION FEATURES The SG7800A/SG7800 series of positive regulators offer self contained, fixed-voltage capability with up to 1.5A of load current and input voltage up to 50V (SG7800A series only). These units feature a unique on-chip trimming system to set the output voltages to within ±1.5% of nominal on the SG7800A series,±2.0% on the SG7800 series. The SG7800A versions also offer much improved line and load regulation characteristics. Utilizing an improved Bandgap reference design, problems have been eliminated that are normally associated with the Zener diode references, such as drift in output voltage and large changes in the line and load regulation. • • • • • • • • All protective features of thermal shutdown, current limiting, and safe-area control have been designed into these units and since these regulators require only a small output capacitor for satisfactory performance, ease of application is assured. Although designed as fixed-voltage regulators, the output voltage can be increased through the use of a simple voltage divider. The low quiescent drain current of the device insures good regulation when this method is used. Product is available in hermetically sealed TO-257, TO-3, TO39 and LCC packages. Output voltage set internally to ±1.5% on SG7800A Input voltage range to 50V max. on SG7800A Two volt input-output differential Excellent line and load regulation Foldback current limiting Thermal overload protection Voltages available: 5V, 12V, 15V Available in surface mount package HIGH RELIABILITY FEATURES - SG7800A/7800 ♦ Available to MIL-STD - 883 ♦ MIL-M38510/10702BXA - JAN7805T ♦ MIL-M38510/10703BXA - JAN7812T ♦ MIL-M38510/10704BXA - JAN7815T ♦ MIL-M38510/10706BYA - JAN7805K ♦ MIL-M38510/10707BYA - JAN7812K ♦ MIL-M38510/10708BYA - JAN7815K ♦ Radiation data available ♦ LMI level "S" processing available SCHEMATIC DIAGRAM * * For normal operation the (VOS) sense pin must be externally connected to the load. LINFINITY 05/01 Rev 1.4 Copyright 1997 1 Microelectronics Inc. 11861 Western Avenue ∞ Garden Grove, CA 92841 (714) 898-8121 ∞ FAX: (714) 893-2570 SG7800A/SG7800 SERIES POSITIVE REGULATOR ABSOLUTE MAXIMUM RATINGS (Note 1) Device Output Voltage 5V 12V 15V Input Voltage (transient) (Note 3) 50V 50V 50V Input Voltage 35V 35V 35V Operating Junction Temperature Hermetic (K, T, IG & L - Packages) ......................... Input Voltage Differential (Output shorted to ground) 35V 35V 35V Storage Temperature Range .......................... -65°C to 150°C Lead Temperature (Soldering, 10 Seconds) ................. 300°C 150°C Note 1. Values beyond which damage may occur. THERMAL DATA K Package: Thermal Resistance-Junction to Case, θJC ................. 3.0°C/W Thermal Resistance-Junction to Ambient, θJA ............... 35°C/W T Package: Thermal Resistance-Junction to Case, θJC .................. 15°C/W Thermal Resistance-Junction to Ambient, θJA ............ 120°C/W IG Package: Thermal Resistance-Junction to Case, θJC ................. 3.5°C/W Thermal Resistance-Junction to Ambient, θJA .............. 42°C/W L Package: Thermal Resistance-Junction to Case, θJC .................. 35°C/W Thermal Resistance-Junction to Ambient, θJA ............ 120°C/W RECOMMENDED OPERATING CONDITIONS Note A. Junction Temperature Calculation: TJ = TA + (PD x θ JA). Note B. The above numbers for θJC are maximums for the limiting thermal resistance of the package in a standard mounting configuration. The θ JA numbers are meant to be guidelines for the thermal performance of the device/pc-board system. All of the above assume no ambient airflow. (Note 2) Operating Junction Temperature Range: SG7800A/SG7800 ........................................ -55°C to 150°C Note 2. Range over which the device is functional. CHARACTERISTIC CURVES Note 3. Operation at high input voltages is dependent upon load current. When load current is less than 5mA, output will rise out of regulation as inputoiutput differential icreases beyond 30V. Note also from Figure 1, that maximum load current is reduced at high voltages. The 50V input rating of the SG140A series refers to ability to withstnd high line or transient conditions without damage. Since the regulator's maximum current capability is reduced, the output may fall out of regulation at high input voltages under nominal loading. FIGURE 1. PEAK OUTPUT CURRENT VS. INPUT - OUTPUT DIFFERENTIAL LINFINITY 05/01 Rev 1.4 Copyright 1997 2 Microelectronics Inc. 11861 Western Avenue ∞ Garden Grove, CA 92841 (714) 898-8121 ∞ FAX: (714) 893-2570 SG7800A/SG7800 SERIES CHARACTERISTIC CURVES POSITIVE REGULATOR (continued) FIGURE 2. MINIMUM INPUT - OUTPUT VOLTAGE VS. LOAD CURRENT FIGURE 3. RIPPLE REJECTION VS. FREQUENCY FIGURE 4. TEMPERATURE COEFFICIENT OF OUTPUT VOLTAGE APPLICATIONS FIGURE 5 - FIXED OUTPUT REGULATOR FIGURE 6 - CIRCUIT FOR INCREASING OUTPUT VOLTAGE FIGURE 7 - HIGH OUTPUT CURRENT, SHORT CIRCUIT PROTECTED FIGURE 8 - ADJUSTABLE OUTPUT REGULATOR, 7V to 30V LINFINITY 05/01 Rev 1.4 Copyright 1997 3 Microelectronics Inc. 11861 Western Avenue ∞ Garden Grove, CA 92841 (714) 898-8121 ∞ FAX: (714) 893-2570 SG7800A/SG7800 SERIES 5.0V POSITIVE REGULATOR ELECTRICAL SPECIFICATIONS (Note 1) (Unless otherwise specified, these specifications apply over the operating ambient temperatures for SG7805A/SG7805 with -55°C ≤ TA ≤ 150°C, VIN = 10V, IO = 500mA for the K and IG -Power Packages-, IO = 100mA for the T and L packages, CIN = 0.33µF, and COUT = 0.1µF. Low duty cycle pulse testing techniques are used which maintains junction and case temperatures equal to the ambient temperature.) SG7805A/SG7805 Parameter Output Voltage Line Regulation (Note 1) Load Regulation (Note 1) Total Output Voltage Tolerance Quiescent Current Quiescent Current Change Dropout Voltage Peak Output Current Short Circuit Current Ripple Rejection Output Noise Voltage (rms) Long Term Stability Thermal Shutdown Test Conditions TJ = 25°C VIN = 7.5V to 20V, TJ = 25°C VIN = 8V to 12V, TJ = 25°C Power Pkgs: IO = 5mA to 1.5A, TJ = 25°C IO = 250mA to 750mA, TJ = 25°C T - Pkg: IO = 5mA to 500mA, TJ = 25°C VIN =8V to 20V Power Pkgs: IO = 5mA to 1.0A, P ≤ 20W T - Pkg: IO = 5mA to 500mA, P ≤ 2W Over Temperature Range TJ = 25°C With Line: VIN = 8V to 25V With Load: IO = 5mA to 1.0A (Power Pkgs.) IO = 5mA to 500mA (T) ∆VO = 100mV, TJ = 25°C Power Pkgs: IO = 1.0A, T - Pkg: IO = 500mA Power Pkgs: VIN = 10V, TJ = 25°C T - Pkg: VIN = 10V, TJ = 25°C Power Pkgs: VIN = 35V, TJ = 25°C T - Pkg: VIN = 35V, TJ = 25°C ∆VIN = 10V, f = 120Hz, TJ = 25°C f = 10Hz to 100KHz (Note 2) 1000hrs. at TJ = 125°C IO = 5mA SG7805 SG7805A Min. Typ. Max. Min. Typ. Max. 4.92 5.00 5.08 4.80 5.00 5.20 5 50 25 5 2 25 2 12 15 50 15 50 5 5 25 25 20 25 5 25 4.85 4.85 5.00 5.00 4 1.5 0.5 2 2.0 1.0 5.15 5.15 7 6 0.8 0.5 0.5 2.5 3.3 2.0 1.2 0.7 4.65 4.65 5.00 5.00 4 1.5 0.5 2 2.0 1.0 V V mA mA mA mA mA 2.5 3.3 2.0 1.2 0.7 V A A A A dB µV/V mV °C 40 40 20 175 20 175 V mV mV mV mV mV 5.35 5.35 7 6 0.8 0.5 0.5 68 68 Units Note 1. All regulation tests are made at constant junction temperature with low duty cycle testing. 2. This test is guaranteed but is not tested in production. LINFINITY 05/01 Rev 1.4 Copyright 1997 4 Microelectronics Inc. 11861 Western Avenue ∞ Garden Grove, CA 92841 (714) 898-8121 ∞ FAX: (714) 893-2570 SG7800A/SG7800 SERIES 12V POSITIVE REGULATOR ELECTRICAL SPECIFICATIONS (Note 1) (Unless otherwise specified, these specifications apply over the operating ambient temperatures for SG7812A/SG7812 with -55°C ≤ TA ≤ 150°C, VIN = 19V, IO = 500mA for the K and IG -Power Packages-, IO = 100mA for the T and L packages, CIN = 0.33µF, and COUT = 0.1µF. Low duty cycle pulse testing techniques are used which maintains junction and case temperatures equal to the ambient temperature.) SG7812A/SG7812 Parameter Output Voltage Line Regulation (Note 1) Load Regulation (Note 1) Total Output Voltage Tolerance Quiescent Current Quiescent Current Change Dropout Voltage Peak Output Current Short Circuit Current Ripple Rejection Output Noise Voltage (rms) Long Term Stability Thermal Shutdown Test Conditions TJ = 25°C VIN = 14.5V to 30V, T J = 25°C VIN = 16V to 22V, TJ = 25°C Power Pkgs: IO = 5mA to 1.5A, TJ = 25°C IO = 250mA to 750mA, TJ = 25°C T - Pkg: IO = 5mA to 500mA, TJ = 25°C VIN = 15.5V to 27V Power Pkgs: IO = 5mA to 1.0A, P ≤ 20W T - Pkg: IO = 5mA to 500mA, P ≤ 2W Over Temperature Range TJ = 25°C With Line: VIN = 15V to 30V With Load: IO = 5mA to 1.0A (Power Pkgs.) IO = 5mA to 500mA (T) ∆VO = 100mV, TJ = 25°C Power Pkgs: IO = 1.0A, T - Pkg: IO = 500mA Power Pkgs: TJ = 25°C T - Pkg: TJ = 25°C Power Pkgs: VIN = 35V, TJ = 25°C T - Pkg: VIN = 35V, TJ = 25°C ∆VIN = 10V, f = 120Hz, TJ = 25°C f = 10Hz to 100KHz (Note 2) 1000hrs. at TJ = 125°C IO = 5mA SG7812 SG7812A Min. Typ. Max. Min. Typ. Max. 11.8 12.0 12.2 11.5 12.0 12.5 12 60 12 120 6 30 6 60 80 28 120 28 10 40 10 60 10 40 10 60 11.7 11.7 12.0 12.0 4 1.5 0.5 2 2.0 1.0 12.3 12.3 7 6 0.8 0.5 0.5 2.5 3.3 1.7 1.2 0.7 11.4 11.4 12.0 12.0 4 1.5 0.5 2 2.0 1.0 40 48 175 V V mA mA mA mA mA 2.5 3.3 1.7 1.2 0.7 V A A A A dB µV/V mV °C 40 48 175 V mV mV mV mV mV 12.6 12.6 7 6 0.8 0.5 0.5 61 61 Units Note 1. All regulation tests are made at constant junction temperature with low duty cycle testing. 2. This test is guaranteed but is not tested in production. LINFINITY 05/01 Rev 1.4 Copyright 1997 5 Microelectronics Inc. 11861 Western Avenue ∞ Garden Grove, CA 92841 (714) 898-8121 ∞ FAX: (714) 893-2570 SG7800A/SG7800 SERIES 15V POSITIVE REGULATOR ELECTRICAL SPECIFICATIONS (Note 1) (Unless otherwise specified, these specifications apply over the operating ambient temperatures for SG7815A/SG7815 with -55°C ≤ TA ≤ 150°C, VIN = 23V, IO = 500mA for the K and IG -Power Packages-, IO = 100mA for the T and L packages, CIN = 0.33µF, and COUT = 0.1µF. Low duty cycle pulse testing techniques are used which maintains junction and case temperatures equal to the ambient temperature.) SG7815A/SG7815 Parameter Output Voltage Line Regulation (Note 1) Load Regulation (Note 1) Total Output Voltage Tolerance Quiescent Current Quiescent Current Change Dropout Voltage Peak Output Current Short Circuit Current Ripple Rejection Output Noise Voltage (rms) Long Term Stability Thermal Shutdown Test Conditions TJ = 25°C VIN = 17.5V to 30V, T J = 25°C VIN = 20V to 26V, TJ = 25°C Power Pkgs: IO = 5mA to 1.5A, TJ = 25°C IO = 250mA to 750mA, TJ = 25°C T - Pkg: IO = 5mA to 500mA, TJ = 25°C VIN = 18.5V to 30V Power Pkgs: IO = 5mA to 1.0A, P ≤ 20W T - Pkg: IO = 5mA to 500mA, P ≤ 2W Over Temperature Range TJ = 25°C With Line: VIN = 18.5V to 30V With Load: IO = 5mA to 1.0A (Power Pkgs.) IO = 5mA to 500mA (T) ∆VO = 100mV, TJ = 25°C Power Pkgs: IO = 1.0A, T - Pkg: IO = 500mA Power Pkgs: TJ = 25°C T - Pkg: TJ = 25°C Power Pkgs: VIN = 35V, TJ = 25°C T - Pkg: VIN = 35V, TJ = 25°C ∆VIN = 10V, f = 120Hz, TJ = 25°C f = 10Hz to 100KHz (Note 2) 1000hrs. at TJ = 125°C IO = 5mA SG7815 SG7815A Min. Typ. Max. Min. Typ. Max. 14.8 15.0 15.2 14.4 15.0 15.6 75 15 150 15 75 8 40 8 30 150 30 100 12 50 12 75 12 75 12 50 14.6 14.6 15.0 15.0 4 1.5 0.5 2 2.2 0.9 15.4 15.4 7 6 0.8 0.5 0.5 2.5 3.3 1.7 1.2 0.7 14.3 14.3 15.0 15.0 4 1.5 0.5 2 2.2 0.9 V V mA mA mA mA mA 2.5 3.3 1.7 1.2 0.7 V A A A A dB µV/V mV °C 40 40 60 175 60 175 V mV mV mV mV mV 15.7 15.7 7 6 0.8 0.5 0.5 60 60 Units Note 1. All regulation tests are made at constant junction temperature with low duty cycle testing. 2. This test is guaranteed but is not tested in production. LINFINITY 05/01 Rev 1.4 Copyright 1997 6 Microelectronics Inc. 11861 Western Avenue ∞ Garden Grove, CA 92841 (714) 898-8121 ∞ FAX: (714) 893-2570 SG7800A/SG7800 SERIES POSITIVE REGULATOR CONNECTION DIAGRAMS & ORDERING INFORMATION Package 3-TERMINAL TO-3 METAL CAN K-PACKAGE 3-PIN TO-39 METAL CAN T-PACKAGE 3-PIN HERMETIC TO-257 IG-PACKAGE (Isolated) 20-PIN CERAMIC LEADLESS CHIP CARRIER L- PACKAGE Note 1. 2. 3. 4. 5. 6. Part No. (See Notes Below) Ambient Temperature Range SG78XXAK/883B SG7805AK/DESC SG7812AK/DESC SG7815AK/DESC SG78XXAK SG78XXK/883B JAN7805K JAN7812K JAN7815K SG78XXK SG78XXK -55°C to 125°C -55°C to 125°C -55°C to 125°C -55°C to 125°C -55°C to 125°C -55°C to 125°C -55°C to 125°C -55°C to 125°C -55°C to 125°C -55°C to 125°C 0°C to 125°C SG78XXAT/883B SG7805AT/DESC SG7812AT/DESC SG7815AT/DESC SG78XXAT SG78XXT/883B JAN7805T JAN7812T JAN7815T SG78XXT -55°C to 125°C -55°C to 125°C -55°C to 125°C -55°C to 125°C -55°C to 125°C -55°C to 125°C -55°C to 125°C -55°C to 125°C -55°C to 125°C -55°C to 125°C SG78XXAIG/883B SG7805AIG/DESC SG7812AIG/DESC SG7815AIG/DESC SG78XXAIG SG78XXIG/883B SG78XXIG -55°C to 125°C -55°C to 125°C -55°C to 125°C -55°C to 125°C -55°C to 125°C -55°C to 125°C -55°C to 125°C SG7805AL/DESC SG7812AL/DESC SG7815AL/DESC SG78XXL/883B -55°C -55°C -55°C -55°C to to to to 125°C 125°C 125°C 125°C Connection Diagram VIN 1 2 CASE IS GROUND VOUT VIN 1 VOUT 2 3 GROUND CASE IS GROUND VOUT GROUND VIN (See Notes 5 & 6) 1. N.C. 2. VIN 3. N.C. 4. N.C. 5. N.C. 6. N.C. 7. GND 8. N.C. 9. N.C. 10. VOUT 3 2 1 20 19 4 18 5 17 6 16 7 15 8 14 9 10 11 12 13 11. N.C. 12. VOUT 13. N.C. 14. N.C. 15. VO SENSE 16. N.C. 17. VIN 18. N.C. 19. N.C. 20. N.C. Contact factory for JAN and DESC product availability. All parts are viewed from the top. "XX" to be replaced by output voltage of specific fixed regulator. Some products will be available in hermetic flat pack (F). Consult factory for price and availability. Both inputs and outputs must be externally connected together at the device terminals. For normal operation, the VO SENSE pin must be externally connected to the load. LINFINITY Microelectronics Inc. 05/01 Rev 1.4 Copyright 1997 7 11861 Western Avenue ∞ Garden Grove, CA 92841 (714) 898-8121 ∞ FAX: (714) 893-2570