ISL88001, ISL88002, ISL88003 ® Data Sheet March 26, 2008 Ultra Low Power 3 Ld Voltage Supervisors in SC-70 and SOT-23 Packages The ISL88001, ISL88002, ISL88003 supervisors are extremely low power 160nA voltage supervisors that help to monitor the power supply voltages in a wide variety of applications. By providing Power-On Reset and supply voltage supervision in small 3 Ld SC-70 and SOT-23 packages, the ISL88001, ISL88002, ISL88003 devices can help to lower system cost, reduce board space requirements and increase the reliability of systems. The most popular voltage trip points are available for standard power supplies from 1.8V to 5.0V (see “Ordering Information” on page 3). These reset threshold voltages are accurate to within ±1.2% and the reset signal is valid down to 1V. Active high and active low reset outputs are available in push-pull and open drain configurations (see “Functional Block Diagrams” on page 2). The ISL88001, ISL88002, ISL88003 devices are specifically designed for low power consumption and high threshold accuracy, making them especially suitable for electronic devices and portable equipment. FN6174.0 Features • Single Voltage Monitoring Supervisors • Fixed-Voltage Options Allow Precise Monitoring of +1.8V, +2.5V, +3.0V, +3.3V and +5.0V Power Supplies • Ultra Low 160nA Supply Current • ±1.2% Voltage Threshold Accuracy • 190ms Power-On Reset Timeout • Reset Signal Valid Down to VDD = 1V • No External Components Necessary • Immune to Power-Supply Transients • Available in Small 3 Ld SC-70 and 3 Ld SOT-23 Pb-free Packages • Pin Compatible with MAX803, MAX809, MAX810 • Pb-Free (RoHS Compliant) Applications • Microprocessor/Microcontroller Systems • Intelligent Instruments Pinouts • Controllers ISL88001, ISL88002 (3 LD SC-70, 3 LD SOT-23) TOP VIEW GND • Computer Systems • Portable/Battery-Powered Equipment • PDA and Hand-Held PC Devices 1 ISL88001 ISL88002 RST 3 VDD 2 ISL88001 has a push-pull RST output ISL88002 has an open-drain RST output ISL88003 (3 LD SC-70, 3 LD SOT-23) TOP VIEW GND 1 ISL88003 RST 3 VDD 2 ISL88003 has a push-pull RST output 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2008. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ISL88001, ISL88002, ISL88003 Functional Block Diagrams VDD VDD POR RST RST POR ± VREF VDD ± VREF VDD GND GND ISL88002 ISL88001 VDD POR ± VREF RST VDD GND ISL88003 Pin Descriptions PIN ISL88001 ISL88002 ISL88003 PIN NAME 1 1 GND Ground IC reference. RST The RST pin is an active-low reset output that is pulled to GND (LOW) when reset is asserted. The ISL88001 is push-pull while the ISL88002 is open drain. 2 RST The RST pin is a push-pull active-high reset output that is pulled to VDD (HIGH) when reset is asserted. 3 VDD Supply Voltage and Monitored Input. The VDD pin is the IC power supply terminal and also the monitored input. 2 3 2 PIN FUNCTION FN6174.0 March 26, 2008 ISL88001, ISL88002, ISL88003 Ordering Information PART NUMBER (Notes 1, 2, 3) PART MARKING RESET VTHVDD (V) TEMPERATURE RANGE (°C) PACKAGE PKG. DWG. # ISL88001IE46Z-T 146 Push-Pull RST 4.64 -40 to +85 3 Ld SC-70 P3.049 ISL88001IE44Z-T 144 Push-Pull RST 4.38 -40 to +85 3 Ld SC-70 P3.049 ISL88001IE31Z-T 131 Push-Pull RST 3.09 -40 to +85 3 Ld SC-70 P3.049 ISL88001IE29Z-T 129 Push-Pull RST 2.92 -40 to +85 3 Ld SC-70 P3.049 ISL88001IE26Z-T 126 Push-Pull RST 2.63 -40 to +85 3 Ld SC-70 P3.049 ISL88001IE23Z-T 123 Push-Pull RST 2.32 -40 to +85 3 Ld SC-70 P3.049 ISL88001IE22Z-T 122 Push-Pull RST 2.19 -40 to +85 3 Ld SC-70 P3.049 ISL88001IE17Z-T 117 Push-Pull RST 1.67 -40 to +85 3 Ld SC-70 P3.049 ISL88001IE16Z-T 116 Push-Pull RST 1.58 -40 to +85 3 Ld SC-70 P3.049 ISL88001IH46Z-T 1H46 Push-Pull RST 4.64 -40 to +85 3 Ld SOT-23 P3.064 ISL88001IH44Z-T 1H44 Push-Pull RST 4.38 -40 to +85 3 Ld SOT-23 P3.064 ISL88001IH31Z-T 1H31 Push-Pull RST 3.09 -40 to +85 3 Ld SOT-23 P3.064 ISL88001IH29Z-T 1H29 Push-Pull RST 2.92 -40 to +85 3 Ld SOT-23 P3.064 ISL88001IH26Z-T 1H26 Push-Pull RST 2.63 -40 to +85 3 Ld SOT-23 P3.064 ISL88001IH23Z-T 1H23 Push-Pull RST 2.32 -40 to +85 3 Ld SOT-23 P3.064 ISL88001IH22Z-T 1H22 Push-Pull RST 2.19 -40 to +85 3 Ld SOT-23 P3.064 ISL88001IH17Z-T 1H17 Push-Pull RST 1.67 -40 to +85 3 Ld SOT-23 P3.064 ISL88001IH16Z-T 1H16 Push-Pull RST 1.58 -40 to +85 3 Ld SOT-23 P3.064 ISL88002IE46Z-T 246 Open Drain RST 4.64 -40 to +85 3 Ld SC-70 P3.049 ISL88002IE44Z-T 244 Open Drain RST 4.38 -40 to +85 3 Ld SC-70 P3.049 ISL88002IE31Z-T 231 Open Drain RST 3.09 -40 to +85 3 Ld SC-70 P3.049 ISL88002IE29Z-T 229 Open Drain RST 2.92 -40 to +85 3 Ld SC-70 P3.049 ISL88002IE26Z-T 226 Open Drain RST 2.63 -40 to +85 3 Ld SC-70 P3.049 ISL88002IE23Z-T 223 Open Drain RST 2.32 -40 to +85 3 Ld SC-70 P3.049 ISL88002IE22Z-T 222 Open Drain RST 2.19 -40 to +85 3 Ld SC-70 P3.049 ISL88002IE17Z-T 217 Open Drain RST 1.67 -40 to +85 3 Ld SC-70 P3.049 ISL88002IE16Z-T 216 Open Drain RST 1.58 -40 to +85 3 Ld SC-70 P3.049 ISL88002IH46Z-T 2H46 Open Drain RST 4.64 -40 to +85 3 Ld SOT-23 P3.064 ISL88002IH44Z-T 2H44 Open Drain RST 4.38 -40 to +85 3 Ld SOT-23 P3.064 ISL88002IH31Z-T 2H31 Open Drain RST 3.09 -40 to +85 3 Ld SOT-23 P3.064 ISL88002IH29Z-T 2H29 Open Drain RST 2.92 -40 to +85 3 Ld SOT-23 P3.064 ISL88002IH26Z-T 2H26 Open Drain RST 2.63 -40 to +85 3 Ld SOT-23 P3.064 ISL88002IH23Z-T 2H23 Open Drain RST 2.32 -40 to +85 3 Ld SOT-23 P3.064 ISL88002IH22Z-T 2H22 Open Drain RST 2.19 -40 to +85 3 Ld SOT-23 P3.064 ISL88002IH17Z-T 2H17 Open Drain RST 1.67 -40 to +85 3 Ld SOT-23 P3.064 ISL88002IH16Z-T 2H16 Open Drain RST 1.58 -40 to +85 3 Ld SOT-23 P3.064 ISL88003IE46Z-T 346 Push-Pull RST 4.64 -40 to +85 3 Ld SC-70 P3.049 ISL88003IE44Z-T 344 Push-Pull RST 4.38 -40 to +85 3 Ld SC-70 P3.049 ISL88003IE31Z-T 331 Push-Pull RST 3.09 -40 to +85 3 Ld SC-70 P3.049 3 FN6174.0 March 26, 2008 ISL88001, ISL88002, ISL88003 Ordering Information (Continued) PART NUMBER (Notes 1, 2, 3) PART MARKING RESET VTHVDD (V) TEMPERATURE RANGE (°C) PKG. DWG. # PACKAGE ISL88003IE29Z-T 329 Push-Pull RST 2.92 -40 to +85 3 Ld SC-70 P3.049 ISL88003IE26Z-T 326 Push-Pull RST 2.63 -40 to +85 3 Ld SC-70 P3.049 ISL88003IE23Z-T 323 Push-Pull RST 2.32 -40 to +85 3 Ld SC-70 P3.049 ISL88003IE22Z-T 322 Push-Pull RST 2.19 -40 to +85 3 Ld SC-70 P3.049 ISL88003IE17Z-T 317 Push-Pull RST 1.67 -40 to +85 3 Ld SC-70 P3.049 ISL88003IE16Z-T 316 Push-Pull RST 1.58 -40 to +85 3 Ld SC-70 P3.049 ISL88003IH46Z-T 3H46 Push-Pull RST 4.64 -40 to +85 3 Ld SOT-23 P3.064 ISL88003IH44Z-T 3H44 Push-Pull RST 4.38 -40 to +85 3 Ld SOT-23 P3.064 ISL88003IH31Z-T 3H31 Push-Pull RST 3.09 -40 to +85 3 Ld SOT-23 P3.064 ISL88003IH29Z-T 3H29 Push-Pull RST 2.92 -40 to +85 3 Ld SOT-23 P3.064 ISL88003IH26Z-T 3H26 Push-Pull RST 2.63 -40 to +85 3 Ld SOT-23 P3.064 ISL88003IH23Z-T 3H23 Push-Pull RST 2.32 -40 to +85 3 Ld SOT-23 P3.064 ISL88003IH22Z-T 3H22 Push-Pull RST 2.19 -40 to +85 3 Ld SOT-23 P3.064 ISL88003IH17Z-T 3H17 Push-Pull RST 1.67 -40 to +85 3 Ld SOT-23 P3.064 ISL88003IH16Z-T 3H16 Push-Pull RST 1.58 -40 to +85 3 Ld SOT-23 P3.064 ISL88001/2/3EVAL1Z Evaluation Platform for ISL88001, ISL88002 and ISL88003 NOTES: 1. For non-standard voltage trip point versions between 1.5V and 5V in 100mV increments, please contact factory for availability. 2. Add “-TK” suffix for 1000 piece Tape and Reel. Please refer to TB347 for details on reel specifications. 3. These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 4 FN6174.0 March 26, 2008 ISL88001, ISL88002, ISL88003 Absolute Maximum Ratings Thermal Information Temperature Under Bias. . . . . . . . . . . . . . . . . . . . . -40°C to +125°C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . -65°C to +150°C Voltage on Any Pin with respect to GND . . . . . . . . . . -0.3V to +6.5V DC Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10mA Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Recommended Operating Conditions Temperature Range (Industrial) . . . . . . . . . . . . . . . . -40°C to +85°C CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. For guaranteed specifications and test conditions, see Electrical Specifications. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Electrical Specifications SYMBOL Over the recommended operating conditions unless otherwise specified. PARAMETER TEST CONDITIONS MIN (Note 4) VTHVDD = 4.64V, 4.38V, 3.09V, 2.92V, 2.63V 1.8 5.5 V VTHVDD = 2.32V, 2.19V, 1.67V, 1.58V 1.8 2.75 V 215 400 nA VDD = 3.3V, VTHVDD = 3.09V, 2.92V, 2.63V 200 350 nA VDD = 2.5V, VTHVDD = 2.32V, 2.19V 175 325 nA VDD = 1.8V, VTHVDD = 1.67V, 1.58V 160 300 nA 4.625 4.681 V 4.750 V 4.433 V 4.498 V 3.112 V 3.150 V 2.960 V 3.000 V 2.662 V 2.701 V 2.348 V 2.383 V 2.216 V 2.249 V 1.690 V 1.715 V 1.599 V 1.623 V TYP MAX (Note 4) UNITS BIAS VDD IDD Supply Voltage Range Supply Current (RESET, RESET open) VDD = 5.0V, VTHVDD = 4.64V, 4.38V VOLTAGE THRESHOLD VTHVDD Falling Fixed VDD Voltage Trip Point VTHVDDHYST Hysteresis at VDD Input TVTHVDD VTHVDD Temperature Coefficient 5 ISL88001, 88002, 88003Ix346, TA = +25°C 4.570 ISL88001, 88002, 88003Ix346 4.500 ISL88001, 88002, 88003Ix344, TA = +25°C 4.327 ISL88001, 88002, 88003Ix344 4.262 ISL88001, 88002, 88003Ix331, TA = +25°C 3.038 ISL88001, 88002, 88003Ix331 3.000 ISL88001, 88002, 88003Ix329, TA = +25°C 2.890 ISL88001, 88002, 88003Ix329 2.850 ISL88001, 88002, 88003Ix326, TA = +25°C 2.598 ISL88001, 88002, 88003Ix326 2.559 ISL88001, 88002, 88003Ix323, TA = +25°C 2.292 ISL88001, 88002, 88003Ix323 2.257 ISL88001, 88002, 88003Ix322, TA = +25°C 2.164 ISL88001, 88002, 88003Ix322 2.131 ISL88001, 88002, 88003Ix317, TA = +25°C 1.650 ISL88001, 88002, 88003Ix317 1.625 ISL88001, 88002, 88003Ix316, TA = +25°C 1.561 ISL88001, 88002, 88003Ix316 1.537 4.380 3.075 2.925 2.630 2.320 2.190 1.670 1.580 1 % 0.48 mV/°C FN6174.0 March 26, 2008 ISL88001, ISL88002, ISL88003 Electrical Specifications SYMBOL Over the recommended operating conditions unless otherwise specified. (Continued) PARAMETER MIN (Note 4) TEST CONDITIONS MAX (Note 4) UNITS TYP RESET / RESET VOL VOH Reset Output Voltage Low Reset Output Voltage High VDD < VTHVDD, for ISL88001 0.2 0.40 V VDD < VTHVDD, Sinking 0.5mA for ISL88002 0.2 0.40 V VDD > VTHVDD, for ISL88003 0.2 0.40 V VDD > VTHVDD, for ISL88001 VDD - 0.4 VDD - 0.2 V VDD - 0.2 V VDD - 0.4 VDD - 0.2 V VDD > VTHVDD, Sourcing 0.5mA, ISL88002 VDD < VTHVDD, for ISL88003 tRPD VTH to Reset Asserted Delay tPOR POR Timeout Delay CLOAD Load Capacitance on Reset Pin 15 140 µs 200 260 5 ms pF NOTE: 4. Parts are 100% tested at +25°C. Temperature limits established by characterization and are not production tested. Pin Description RST The ISL88003 push-pull RST output is set to VDD (HIGH) whenever the device is first powered up or VDD falls below its respective minimum voltage sense level. to a µP/µC if this voltage is less than the preset voltage trip point. The reset signal prevents system operation during a power failure or brownout condition. This reset signal remains asserted until VDD exceeds the voltage threshold setting for the reset time delay period tPOR. See Figure 2. VDD RST The RST output functions identically to the complementary RST output. On the ISL88001, this is a push-pull output. On the ISL88002, it is an open drain output that is pulled to GND (LOW) when reset is asserted. Suggested pull-up RST resistor values are in the range of 5kΩ to 100kΩ. VDD VDD RPU* ISL88001 ISL88002* ISL88003 RESET OUTPUT RESET INPUT µP/µC VDD The VDD pin is the power supply terminal. The voltage at this pin is compared against an internal factory-programmed voltage trip point, VTHVDD. A reset is first asserted when the device is initially powered up to ensure that the power supply has stabilized. Thereafter, reset is again asserted whenever VDD falls below VTHVDD. The device is designed with hysteresis to help prevent chattering due to noise. Principles of Operation The ISL88001, ISL88002, ISL88003 devices provide a low power, high accuracy solution for those voltage monitoring applications needing supply voltage supervision with power reset control. By integrating these features into small 3 Ld SC-70 and 3 Ld SOT-23 packages and consuming as little as 160nA of supply current, these devices can lower system cost and reduce board space requirements. Low Voltage Monitoring During normal operation, the ISL88001, ISL88002, ISL88003 devices monitor the voltage level of VDD. The device asserts a reset signal (RST = LOW or RST = HIGH) 6 GND GND *Necessary for ISL88002 FIGURE 1. TYPICAL APPLICATION DIAGRAM Power-On Reset (POR) Applying power to the ISL88001, ISL88002, ISL88003 activates a POR circuit, which asserts reset once VDD = 1 V. (i.e. RST goes LOW). This provides several benefits: • It prevents the system microprocessor from starting to operate with insufficient voltage. • It prevents the processor from operating prior to stabilization of the oscillator. • It ensures that the monitored device is held out of operation until internal registers are properly loaded. • It allows time for an FPGA to download its configuration prior to initialization of the circuit. FN6174.0 March 26, 2008 ISL88001, ISL88002, ISL88003 VTH/VPOR VDD 1V tPOR tRPD tPOR RST FIGURE 2. VOLTAGE MONITORING TIMING DIAGRAM The reset signal remains asserted until VDD rises above the minimum voltage sense level for time period tPOR. This ensures that the VDD voltage has stabilized. Optional VDD de-coupling capacitance can be added to filter transients if needed. See Figures 13 and 14 illustrating the available evaluation platform, ISL88001/2/3EVAL1Z. This evaluation board is shipped with the many released variants loosely packed and the 4.6V threshold variants mounted for immediate evaluation. Parametric Performance VDD VDD VDD RST RST FIGURE 3. ISL88001 RST tPOR ~144ms 7 RST FIGURE 4. ISL88002 RST tPOR ~155ms, RPU = 5kΩ FN6174.0 March 26, 2008 ISL88001, ISL88002, ISL88003 Parametric Performance (Continued) VDD RST FIGURE 6. ISL88003 tPRD ~26µs 4.75 2.96 4.70 2.94 2.9V VTHVDD (V) 4.6V VTHVDD (V) FIGURE 5. ISL88003 RST tPOR ~145ms 4.65 4.60 2.90 2.88 4.55 4.50 2.92 -40 -20 0 25 50 85 2.86 125 -40 -20 2.23 1.58 2.21 1.58 1.58V VTHVDD (V) 2.2V VTHDD (V) 25 50 85 125 FIGURE 8. ISL8800x 2.9V VTHVDD vs TEMPERATURE FIGURE 7. ISL8800x 4.6V VTHVDD vs TEMPERATURE 2.19 2.17 2.15 2.13 0 TEMPERATURE (°C) TEMPERATURE (°C) 1.57 1.57 1.56 1.56 -40 -20 0 25 50 85 125 TEMPERATURE (°C) FIGURE 9. ISL8800x 2.2V VTHVDD vs TEMPERATURE 8 1.55 -40 -20 0 25 50 85 125 TEMPERATURE (°C) FIGURE 10. ISL8800x 1.58V VTHVDD vs TEMPERATURE FN6174.0 March 26, 2008 ISL88001, ISL88002, ISL88003 Parametric Performance (Continued) 3.0 1.015 2.5 NORMALIZED IDD NORMALIZED tPOR 1.010 1.005 1.000 0.995 1.5 1.0 0.990 0.985 2.0 0.5 -40 -20 0 25 50 TEMPERATURE (°C) 85 125 -40 -20 0 25 50 85 125 TEMPERATURE (°C) FIGURE 11. ISL8800x NORMALIZED +25°C tPOR vs TEMPERATURE FIGURE 12. ISL8800x NORMALIZED +25°C IDD vs TEMPERATURE ISL88001/2/3EVAL1Z Evaluation Platform VDD 1k ISL88001 ISL88002 ISL88003 GND RST2 RST1 FIGURE 13. ISL88001/2/3EVAL1Z SCHEMATIC 9 RST3 FIGURE 14. ISL88001/2/3EVAL1Z PHOTOGRAPH FN6174.0 March 26, 2008 ISL88001, ISL88002, ISL88003 Small Outline Transistor Plastic Packages (SC70-3) 0.20 (0.008) M P3.049 VIEW C C 3 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE CL b INCHES SYMBOL 6 5 4 CL CL E1 E 1 2 3 e e1 D C CL A A2 SEATING PLANE A1 -C- PLATING b1 0.043 0.80 1.10 - 0.004 0.00 0.10 - A2 0.031 0.039 0.80 1.00 - b 0.009 0.016 0.25 0.40 - b1 0.009 0.014 0.25 0.35 c 0.004 0.007 0.10 0.18 6 c1 0.004 0.007 0.10 0.16 6 D 0.071 0.087 1.80 2.20 3 E 0.071 0.094 1.80 2.40 - E1 0.045 0.053 1.15 1.35 3 e 0.0256 Ref 0.65 Ref - e1 0.0512 Ref 1.30 Ref - 0.010 0.018 0.017 Ref. 0.26 0.46 4 0.420 Ref. 0.006 BSC 0° N c1 NOTES 0.031 α c MAX 0.000 L2 b MIN A L WITH MILLIMETERS MAX A1 L1 0.10 (0.004) C MIN - 0.15 BSC 8° 0° 3 8° - 3 5 R 0.004 - 0.10 - R1 0.004 0.010 0.15 0.25 Rev. 0 11/06 NOTES: BASE METAL 1. Dimensioning and tolerances per ASME Y14.5M-1994. 2. Package conforms to EIAJ SC70 and JEDEC MO-203AA. 4X θ1 3. Dimensions D and E1 are exclusive of mold flash, protrusions, or gate burrs. R1 4. Footlength L measured at reference to gauge plane. 5. “N” is the number of terminal positions. R GAUGE PLANE SEATING PLANE L C L1 α L2 6. These Dimensions apply to the flat section of the lead between 0.08mm and 0.15mm from the lead tip. 7. Controlling dimension: MILLIMETER. Converted inch dimensions are for reference only. 4X θ1 VIEW C 10 FN6174.0 March 26, 2008 ISL88001, ISL88002, ISL88003 Small Outline Transistor Plastic Packages (SOT23-3) 0.20 (0.008) M P3.064 VIEW C C 3 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE CL b INCHES SYMBOL 6 5 4 CL CL E1 E 1 2 3 e e1 D C CL A A2 A1 WITH b b1 MILLIMETERS MAX MIN MAX NOTES A 0.035 0.044 0.89 1.12 - A1 0.001 0.004 0.013 0.10 - A2 0.035 0.037 0.88 0.94 - b 0.015 0.020 0.37 0.50 - b1 0.012 0.018 0.30 0.45 - c 0.003 0.007 0.085 0.18 6 c1 0.003 0.005 0.08 0.13 6 D 0.110 0.120 2.80 3.04 3 E 0.083 0.104 2.10 2.64 - E1 0.047 0.055 1.20 1.40 3 SEATING PLANE e 0.0374 Ref 0.95 Ref - -C- e1 0.0748 Ref 1.90 Ref - L - 0.10 (0.004) C PLATING MIN c c1 0.016 0.21 0.41 4 L1 0.024 Ref 0.60 Ref - L2 0.010 Ref 0.25 Ref - N 3 3 5 R 0.004 - 0.10 - - R1 0.004 0.010 0.10 0.25 - a 0° 8° 0° 8° Rev. 1 11/06 BASE METAL NOTES: 1. Dimensioning and tolerance per ASME Y14.5M-1994. 4X θ1 2. Package conforms to EIAJ SC-74 and JEDEC MO178AB. 3. Dimensions D and E1 are exclusive of mold flash, protrusions, or gate burrs. R1 4. Footlength L measured at reference to gauge plane. R 5. “N” is the number of terminal positions. GAUGE PLANE SEATING PLANE L C L1 4X θ1 α L2 6. These Dimensions apply to the flat section of the lead between 0.08mm and 0.15mm from the lead tip. 7. Controlling dimension: MILLIMETER. Converted inch dimensions are for reference only 8. Die is facing up for mold die and trim-form. VIEW C All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 11 FN6174.0 March 26, 2008