SMD 14 Pin 5 Tap TTL Compatible Active Delay Lines Delays are ±5% or ±2 nS Tap Total 5, 10, 15, 20 6, 12, 18, 24 7, 14, 21, 28 8, 16, 24, 32 9, 18, 27, 36 10, 20, 30, 40 12, 24, 36, 48 15, 30, 45, 60 20, 40, 60, 80 25, 50, 75, 100 30, 60, 90, 120 35, 70, 105, 140 40, 80, 120, 160 45, 90, 135, 180 50, 100, 150, 200 60, 120, 180, 240 70, 140, 210, 280 SMD Part Number 25 30 35 40 45 50 60 75 100 125 150 175 200 225 250 300 350 Delays are ±5% or ±2 nS Tap Total 80, 160, 240, 320 84, 168, 252, 336 88, 176, 264, 352 90, 180, 270, 360 94, 188, 282, 376 100, 200, 300, 400 110, 220, 330, 440 120, 240, 360, 480 130, 260, 390, 520 140, 280, 420, 560 150, 300, 450, 600 160, 320, 480, 640 170, 340, 510, 680 180, 360, 540, 720 190, 380, 570, 760 200, 400, 600, 800 EPA2398-25 EPA2398-30 EPA2398-35 EPA2398-40 EPA2398-45 EPA2398-50 EPA2398-60 EPA2398-75 EPA2398-100 EPA2398-125 EPA2398-150 EPA2398-175 EPA2398-200 EPA2398-225 EPA2398-250 EPA2398-300 EPA2398-350 SMD Part Number 400 420 440 450 470 500 550 600 650 700 750 800 850 900 950 1000 EPA2398-400 EPA2398-420 EPA2398-440 EPA2398-450 EPA2398-470 EPA2398-500 EPA2398-550 EPA2398-600 EPA2398-650 EPA2398-700 EPA2398-750 EPA2398-800 EPA2398-850 EPA2398-900 EPA2398-950 EPA2398-1000 Delay times referenced from input to leading edges at 25°C, 5.0V, with no load. DC Electrical Characteristics Parameter Test Conditions VOH VOL VIK IIH Schematic Min Max Unit High-Level Output Voltage Low-Level Output Voltage Input Clamp Voltage High-Level Input Current VCC = min. VIL = max. I OH = max VCC = min. VIH = min. IOL= max VCC = min. II = IIK VCC = max. VIN = 2.7V VCC = max. VIN = 5.25V IIL Low-Level Input Current VCC = max. VIN = 0.5V IOS Short Circuit Output Current VCC = max. VOUT = 0. (One output at a time) ICCH High-Level Supply Current VCC = max. VIN = OPEN ICCL Low-Level Supply Current VCC = max. VIN = 0 TRO Output Rise Time Td ≤ 500 nS (0.75 to 2.4 Volts) Td > 500 nS NH Fanout High-Level Output VCC = max. VOH = 2.7V NL Fanout Low-Level Output VCC = max. VOL = 0.5V .200 PCA EPA2398-25 Date Code .300 .280 Max. Suggested Solder Pad Layout V V V µA mA mA mA 14 VCC .300 .100 .055 4 6 8 OUTPUT INPUT 1 7 GROUND 75 mA 75 mA 4 nS 5 nS 20 TTL LOAD 10 TTL LOAD VCC VIH VIL IIK IOH IOL PW* d* TA 10 Supply Voltage High-Level Input Voltage Low-Level Input Voltage Input Clamp Current High-Level Output Current Low-Level Output Current Pulse Width of Total Delay Duty Cycle Operating Free-Air Temperature Min Max Unit 4.75 2.0 5.25 V V V mA mA mA % % °C 0.8 -18 -1.0 20 40 0 40 +70 .430 .03 Input Pulse Test Conditions @ 25° C EIN PW TRI PRR .01 Typ. .200 Max. .050 .300 VCC Pulse Input Voltage Pulse Width % of Total Delay Pulse Rise Time (0.75 - 2.4 Volts) Pulse Repetition Rate @ Td ≤ 200 nS Pulse Repetition Rate @ Td > 200 nS Supply Voltage ELECTRONICS EPA2398 10/92 12 *These two values are inter-dependent. .200 .780 Max. .02 -40 0.5 -1.2 50 1.0 -2 -100 Recommended Operating Conditions Package .420 Max. 2.7 INC. Unit 3.2 50 2.0 5.0 100 5.0 Volts % nS MHz KHz Volts 16799 SCHOENBORN ST. NORTH HILLS, CA 91343 TEL: (818) 892-0761 FAX: (818) 894-5791