PRODUCT DATASHEET GxFIBER-SFP iNDUSTRIAL eTHERNET GIGABIT fIBER tRANSCEIVERS PRODUCT HIGHLIGHTS n n n SFP 1.25 Gbps fiber transceivers with LC style connectors Pluggable for quick and easy installation - saves you time Industry standard Small Form Factor (MSA compliant) - saves you space n Multimode and singlemode models available n Noise immune fiber runs from 550 m to 80 km n Industrial rated for -40 to 85°C operation n Vibration resistance latching mechanism n Small Form Factor Pluggable MSA compliant Lead and Hazardous Substance Free RECOMMENDED OPERATING CONDITIONS Fully compliant with IEEE 802.3z Gigabit Ethernet standards Parameter Min. Typ. Max Low power consumption Operating Temperature -40 - n Storage Temperature -40 - n Standard duplex LC receptacle n n Humidity Laser Class 1 product - IEC60825-1 compliant Unit Note 85 o C - 85 o C - 5 - 95 % non-condensing Power Supply Voltage 3.1 3.3 3.5 V - Supply Current (3.3V) - - 85 mA Data Rate - 1250 - Mbit/s - MECHANICAL DIMENSIONS (UNITS IN MM) ORDERING GUIDE Part Number GMFIBER-SFP-500K Availability Mode Data Rate (Mbps) Light Source TX (dBm) Min. TX (dBm) Max. RX (dBm) Sen Connector Type Nominal Max. Distance standard multimode 1.25 850 VCSEL -9 -3 -18 LC 550m GMFIBER-SFP-2K special order see note 1.25 1310 FP -9 -3 -20 LC 2km* GSFIBER-SFP-10K standard singlemode 1.25 1310 FP -9 -3 -20 LC 10km GSFIBER-SFP-30K special order singlemode 1.25 1550 DFB -4 2 -23 LC 30km GSFIBER-SFP-50K special order singlemode 1.25 1550 DFB -4 2 -23 LC 50km GSFIBER-SFP-80K special order singlemode 1.25 1550 DFB 0 5 -23 LC 80km Note: Use this special singlemode transceiver with multimode fiber cable for a nominal maximum link distance of 2 km. This transceiver offsets the transmitted light (so no mode conditioning patch cord is required) and is specifically for use with multimode fiber cable. It is recommended that this transceiver be used on both ends of the cable for best performance. Do not use this transceiver with singlemode fiber cable. solutions for your industrial networking challenges www.sixnet.com gxfiber-sfp industrial fast ethernet fiber transceivers Transmitter optical characteristics: Parameter Rating1 Min. Typ. Max. Unit Note Output Optical Power From Multimode Fiber 550M, 2km2 -9 - -3 dBm For MM fiber Output Optical Power From Single Mode Fiber 10km 30km 50km 80km -9 -4 -4 0 - -3 2 2 5 dBm For SM fiber 9 - - dB For MM fiber 550m 2km2 10km,30km 50km, 80km 830 1270 1280 1500 850 1310 1310 1550 860 1355 1355 1580 nm For MM fiber For SM fiber For SM fiber For SM fiber Spectral Width (RMS) 550m 2km 10km - - 0.85 4 4 nm For MM fiber For MM fiber For SM fiber Spectral Width (-20dB) 30km, 50km, 80km - - 1 nm For SM fiber Side Mode Suppression Ratio 30km, 50km, 80km 30 - - dB For SM fiber Rise/Fall time (10%-90%) - - - 260 ps - Relative Intensity Noise - - - -117 dB/Hz - Total Jitter - - - 227 ps - Output Eye Compliant with IEEE802.3z 550m 2km 10km, 30km, 50km, 80km - - 0 -3 -3 dBm For MM fiber For MM fiber For SM fiber 550m 2km 10km 30km, 50km, 80km - - -18 -20 -20 -23 550m 2km 10km, 30km, 50km, 80km 770 1260 1260 - 1610 Loss of Signal - Asserted 550m 2km 10km 30km,50km, 80km -32 -35 -35 -35 - - Loss of Signal - Deasserted 550m 2km 10km 30km,50km, 80km - -18 -20 -20 -23 Extinction Ratio Output Center Wavelength receiver optical characteristics: Optical Input Power Sensitivity Operating Wavelength -45 dBm For MM fiber For SM fiber For SM fiber For SM fiber nm For MM fiber For MM fiber For SM fiber dBm For MM fiber For MM fiber For SM fiber For SM fiber dBm For MM fiber For MM fiber For SM fiber For SM fiber Note 1: The distance rating is for reference only. For accurate distance estimations, the power budget should be used. Note 2: The 2 km transmission distance corresponds to using the special GMFIBER-SFP-2K transceiver with multimode fiber cable. This transceiver offsets the transmitted light (so no mode conditioning patch cord is required) and is specifically for use with multimode fiber cable. It is recommended that this transceiver be used on both ends of the cable for best performance. Do not use this transceiver with singlemode fiber cable. All specifications are subject to change. Consult factory for latest info. SIXNET Technology Park 331 Ushers Road • Ballston Lake, NY 12019 • USA 1.518.877.5173 • Fax 1.518.877.8346 • [email protected] solutions for your industrial networking challenges Datasheet gxfiber-sfp Rev: 15 June, 2009 www.sixnet.com