Document 286-1 SMT Power Inductors - LPO6013 Series • Very low profile – only 1.3 mm high! • Handles saturating current up to 1.9 Amps Designer’s Kit C352 contains 3 each of all values Core material Ferrite Core and winding loss See www.coilcraft.com/coreloss Terminations RoHS compliant silver-palladium-platinum-glass frit. Other terminations available at additional cost. Weight 111 – 122 mg Ambient temperature –40°C to +85°C with Irms current, +85°C to +125°C with derated current Storage temperature Component: –40°C to +125°C. Packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 1000/7″reel; 3500/13″ reel Plastic tape: 12 mm wide, 0.23 mm thick, 8 mm pocket spacing, 1.4 mm pocket depth Recommended pick and place nozzle OD: 5.6 mm; ID: ≤ 2.8 mm PCB washing Only pure water or alcohol recommended 1 2 2 Part number 1 LPO6013-102ML_ LPO6013-152ML_ LPO6013-222ML_ LPO6013-332ML_ LPO6013-392ML_ L2 (µH) 1.0 1.5 2.2 3.3 3.9 DCR SRF max typ 2Isat3 3Irms4 (Ohms) (MHz) (A) (A) ±20% ±20% ±20% ±20% ±20% 0.06 0.07 0.08 0.11 0.13 200 200 150 110 100 1.9 1.6 1.3 1.1 1.0 1.5 1.4 1.3 1.3 1.2 LPO6013-472ML_ LPO6013-682ML_ LPO6013-822ML_ LPO6013-103KL_ LPO6013-153KL_ 4.7 ±20% 6.8 ±20% 8.2 ±20% 10. ±10% 15. ±10% 0.15 0.20 0.22 0.30 0.38 90 70 65 60 47 0.90 0.70 0.70 0.60 0.55 1.2 1.2 1.0 1.0 0.85 LPO6013-223KL_ LPO6013-333KL_ LPO6013-393KL_ LPO6013-473KL_ LPO6013-683KL_ 22. ±10% 33. ±10% 39. ±10% 47. ±10% 68. ±10% 0.52 0.73 0.96 1.0 1.7 37 30 28 25 21 0.45 0.40 0.35 0.30 0.28 0.80 0.74 0.67 0.60 0.49 LPO6013-104KL_ LPO6013-154KL_ LPO6013-224KL_ LPO6013-334KL_ LPO6013-474KL_ 100. ±10% 150. ±10% 220. ±10% 330. ±10% 470. ±10% 17 14 10 8 7 0.22 0.19 0.15 0.13 0.10 0.35 0.30 0.26 0.23 0.20 5.6 0.09 4.7 0.07 0.18 0.13 LPO6013-684KL_ 680. ±10% LPO6013-105KL_ 1000. ±10% 3.2 4.3 5.8 7 10 14 21 1. When ordering, please specify termination and packaging code: LPO6013-473KLC Termination: L = RoHS compliant silver-palladium-platinum-glass frit. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic tape (1000 parts per full reel). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D = 13″ machine-ready reel. EIA-481 embossed plastic tape (3500 parts per full reel). 2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc. 3. DC current at which the inductance drops 10% (typ) from its value without current. 4. Current that causes a 40°C temperature rise from 25°C ambient. 5. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Specifications subject to change without notice. Please check our website for latest information. © Coilcraft, Inc. 2009 Document 286-1 Revised 10/15/08 Document 286-2 SMT Power Inductors - LPO6013 Series Typical L vs Frequency Typical L vs Current 10000 10000 1000 µH 100 µH 100 10 µH 10 1 µH 1 100 µH 100 10 µH 10 1 µH 1 0.1 0.01 1000 µH 1000 Inductance (µH) Inductance (µH) 1000 1 0.1 10 0.1 0.01 10 Current (A) Irms Derating 0.051 max 1,3 120 0.220 max 5,6 110 Dash number 0.040 ±0.005 1,016 ±0,127 100 90 XXX 0.236 max 6,0 80 X 70 60 50 Internal code 0.134 3,4 40 25°C Percent of rated Irms 1 0.1 Frequency (MHz) 30 20 10 0.200 5,08 0 -40 -20 0 20 40 60 80 100 120 140 Recommended Land Pattern 0.050 1,27 Ambient temperature (°C) 0.230 5,84 Dimensions are in inches mm Specifications subject to change without notice. Please check our website for latest information. © Coilcraft, Inc. 2009 Document 286-2 Revised 10/15/08