TT GCR2010G-10R000JT3 Glueable chip resistor Datasheet

Resistors
Glueable Chip Resistor
GCR Series
Suitable for conductive adhesive
Planar and wraparound versions
High temperature operation to 200°C
Non-magnetic (G, P & EW types)
Range 0805 to 2512 at 1R0 to 10M
RoHS compliant
All parts are Pb-free and comply with EU Directive 2011/65/EU (RoHS2)
Electrical Data
Size
Power @70°C
W
Resistance range
0805
1206
0.125
0.25
ohms
Tolerance
%
LEV
V
TCR
ppm/°C
Operating temperature
2512
0.625
1
1R0 to 10M
1, 5
150
200
400
500
<10R:200 ≥10R:100
°C
Thermal Impedance
2010
-55 to +200
°C/W
220
A
1.5
160
Values
75
40
E24 or E96 preferred - other values to special order
Zero-ohm jumper current rating
Zero-ohm jumper residual resistance
2
milliohms
<50
Physical Data (All dimensions in mm and nominal weight in g)
L
W
T
A&C
Wt.
0805
2.0
+0.2/-0.15
1.25
±0.15
0.5
±0.15
0.4
±0.2
0.009
1206
3.15
+0.2/-0.2
1.6
±0.15
0.5
±0.15
0.45
±0.2
0.020
2010
5.0
±0.2
2.5
±0.2
0.65
±0.15
0.5
+0.25/-0.3
0.036
2512
6.25
±0.25
3.2
±0.2
0.65
±0.15
0.6
+0.25/-0.3
0.055
Construction
Planar gold G type or PtAg P types: Electrodes, resistor material
and overglaze are printed onto an alumina substrate. The resistors
are laser trimmed to the required value and protected.
Wraparound EW type: Thick-film PtAg electrodes, resistor material
and overglaze are printed onto an alumina substrate. The resistors
are laser trimmed to the required value and protected. The
terminations are wraparound coated with a polymer Ag material.
G & P types
EW & GW types
T
W
L
T
A
L
A
W
Wrap-around terminations
(3 faces)
Marking
The components are not marked; all data is printed onto the
packaging.
Solvent Resistance
The component is resistant to all normal industrial cleaning
solvents suitable for printed circuits.
Wraparound GW type: These are made as the EW type then plated
with a nickel barrier and Gold. All termination styles are suitable
for attachment with conductive adhesive.
General Note
TT Electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT Electronics’ own data and is considered accurate at time of going to print.
BI Technologies IRC Welwyn
www.ttelectronics.com/resistors
© TT Electronics plc
01.18
Glueable
Chip Resistor
GCR Series
Performance Data
Maximum
ΔR
Load at rated power (1000hrs at 70°C)
Derating Curve
2% + 0.01Ω
Derating from rated power at 70°C
P/Pr
See Derating Curve
Short term overload
ΔR
1% + 0.01Ω
Dry heat (1000hrs at 200°C)
ΔR
2% + 0.01Ω
Damp heat steady state (56 days, 40°C, ≥90% RH)
ΔR
1% + 0.01Ω
Climatic
ΔR
1% + 0.01Ω
Temperature rapid change (5 cycles -55ºC to +200ºC)
ΔR
1% + 0.01Ω
100%
0
70
155
200
Ambient temperature degC
Packaging
0805 and 1206 GCR series resistors are supplied on 8mm carrier tape and 7 inch reels as per IEC 286-3, quantity per reel; 3000.
2010 and 2512 GCR series resistors are supplied on 12mm carrier tape and 7 inch reels as per IEC 286-3, quantity per reel; 2010:
3000pcs; 2512: 1800pcs.
Ordering Procedure
Ordering Procedure
Example: GCR1206G-10KFT3 (GCR1206 in gold planar format at 10 kilohms ±1%, Pb-free)
G
C
R
1
2
0
6
G
1
2
1
0
K
3
F
T
4
3
5
1
2
3
4
5
Type
Termination
Value
Tolerance
Packing
3/4 characters
R = ohms
K = kilohms
M = megohms
R000 = jumper
F = ±1%
J = ±5%
Omit for
jumper
0805,1206,
Tape, up to 3000/reel
2010
T18
2512
Tape, up to 1800/reel
GCR0805 G
GCR1206 P
GCR2010 EW
GCR2512
GW
Gold planar
PtAg planar
Polymer Ag wraparound
Ni Barrier & Au plated
wraparound
General Note
TT Electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT Electronics’ own data and is considered accurate at time of going to print.
T3
BI Technologies IRC Welwyn
www.ttelectronics.com/resistors
© TT Electronics plc
01.18
Similar pages