CCD multichannel detector heads C7040 C7041 Designed for back-thinned CCD area image sensor The C7040 and C7041 are high sensitivity multichannel detector heads for use with back-thinned CCD area image sensors (S7030/ S7031 series, S11500-1007) that offer high UV sensitivity and quantum ef¿ciency. The C7040 is designed for the non-cooled type (S7030 series, S11500-1007), while the C7041 for the one-stage TE-cooled type (S7031 series) for detection at even lower light levels. Both the C7040 and C7041 incorporate a low-noise driver/ampli¿er circuit that provides reliable operation from simple external signals. The C7041 also includes a highly stable temperature controller that cools the sensor to a preset temperature level (Ts=-10 °C) as soon as the power is turned on. If the cooler fails and causes internal circuitry to overheat, the built-in protection circuit automatically turns off the power to the thermoelectric cooler. Despite its compact size, the housing con¿guration is designed for good heat dissipation, and threaded mounting holes on the front panel allow connections to other devices such as monochrometers. The table (P.2) shows back-thinned CCD image sensors for the C7040 and C7041. The C7040 and C7041 do not come with a CCD image sensor, so select the desired sensor and order it separately. Controller for multichannel detector head C7557-01 is also available. The software supplied with the C7557-01 allows easy control of the multichannel detector head and data acquisition. Features Applications Designed for back-thinned CCD area image sensor*1 C7040: for non-cooled type (S7030 series, S11500-1007) C7041: for TE-cooled type (S7031 series) Fluorescence spectroscopy Line binning operation*2/area scanning operation Raman spectroscopy Other low-light-level detection Driver/ampli¿er circuit for low noise CCD operation Highly stable temperature controller (C7041) Cooling temperature: -10 °C ± 0.05 °C Simple signal input operation Compact con¿guration *1: In normal CCD image sensors that receive light from the front surface, the active area is covered with electrodes for charge transfer. These electrodes cut off UV radiation incident on the image sensor and also reduce the quantum ef¿ciency. In contrast, back-thinned CCD image sensors have a unique structure in which the back of the active area is ¿nely ground to allow light to enter from the back surface. This structure ensures high UV sensitivity and quantum ef¿ciency because incident light need not pass through the electrodes. *2: The CCD area image sensor can be operated like a linear image sensor having a large active area by transferring all the pixel signals in the vertical direction to the horizontal register (this is referred to as line binning). www.hamamatsu.com 1 CCD multichannel detector heads C7040, C7041 Selection guide The table below shows CCD area image sensors applicable for the C7040 and C7041. Since the C7040 and C7041 do not include a CCD area image sensor, so select the desired sensor and order it separately. CCD area image sensor Type No. C7040 C7041 Type No. Number of pixels Number of active pixels S7030-0906 S7030-0907 S7030-0908 S7030-1006 S7030-1007 S7030-1008 S11500-1007 S7031-0906S S7031-0907S S7031-0908S S7031-1006S S7031-1007S S7031-1008S 532 × 64 532 × 128 532 × 256 1044 × 64 1044 × 128 1044 × 256 1044 × 128 532 × 64 532 × 128 532 × 256 1044 × 64 1044 × 128 1044 × 256 512 × 58 512 × 122 512 × 250 1024 × 58 1024 × 122 1024 × 250 1024 × 122 512 × 58 512 × 122 512 × 250 1024 × 58 1024 × 122 1024 × 250 Active area [mm (H) × mm (V)] 12.288 × 1.392 12.288 × 2.928 12.288 × 6.000 24.576 × 1.392 24.576 × 2.928 24.576 × 6.000 24.576 × 2.928 12.288 × 1.392 12.288 × 2.928 12.288 × 6.000 24.576 × 1.392 24.576 × 2.928 24.576 × 6.000 Note: CCD multichannel detector head C7042 for two-stage TE-cooled CCD area image sensor S7032/-1006/-1007/-1008 is also available. Absolute maximum ratings Parameter Supply voltage (for digital circuitry) Supply voltage (for analog circuitry) Supply voltage Digital input voltage Operating temperature Storage temperature C7040 C7041 C7040 C7041 Symbol VD1 VA1+ VA1VA2 VD2 Vp VF Topr Tstg Min. -0.5 0 +10 -20 0 Typ. - Max. +7 +18 -18 +30 +7 +7 +14 VD (1, 2) +50 +35*3 +70 +50 Unit V °C *3: The maximum value may be lower, depending on the drive frequency and the number of sensor pixels. Electrical characteristics (Ta=25 °C, VD1=+5 V, VA1+=+15 V, VA1-=-15 V, VA2=+24 V, VD2=+5 V, Vp=+5 V, VF=+12 V, unless otherwise noted) Parameter High level Low level Digital input CLK frequency Data video readout frequency Start pulse width High level (Io=-6 mA) Low level (Io=+6 mA) Power supply operating conditions Digital circuitry Digital output Analog circuitry Voltage Other Current VD1 (+5 VDC) VA1+ (+15 VDC) VA1- (-15 VDC) VA2 (+24 VDC) VD2 (+5 VDC)*4 Vp (+5 DC)*4 VF (+12 VDC)*4 Symbol VIH VIL fCLK fv tst VIH VIL Min. +2.0 -0.5 1/fCLK +2.0 - Typ. - Max. VD (1, 2) +0.8 1 fCLK/4 +0.8 Unit V V MHz Hz s V V VD1 VA1+ VA1VA2 VD2 Vp VF - +4.75 +14.5 -14.5 +23.5 +4.75 +4.75 +11.75 - +5.0 +15.0 -15.0 +24.0 +5.0 +5.0 +12.0 +100 +5.25 +15.5 -15.5 +24.5 +5.25 +5.25 +12.25 +200 +100 -100 +30 +30 +2.5 - V V V V V V V mA mA mA mA mA A mA *4: C7041 2 CCD multichannel detector heads C7040, C7041 Electrical and optical characteristics (Ta=25 °C, Ts=-10 °C, VD1=+5 V, VA1+=+15 V, VA1-=-15 V, VA2=+24 V, VD2=+5 V, Vp=+5 V, VF=+12 V) Parameter Spectral response range Vertical Full well capacity Horizontal Conversion gain*5 C7040 (Ta=25 °C) Dark current*6 C7041 (Ta=-10 °C) Readout noise Dynamic range Photo response non-uniformity*7 Symbol O Min. 240 800 - Fw Sv DS Nr DR PRNU Typ. 200 to 1100 320 1000 15 100 3 20 33333 ±3 Max. 1000 30 ±10 Unit nm keV/ee-/pixel/s e- rms % *5: Including the circuit gain *6: At MPP mode. Vertical register value. The actual value equals the sum of the vertical direction because of the binning operation. *7: Measured at 50 % of the full well capacity Speci¿cations for temperature controller (C7041) (Ta=25 °C, VD1=+5 V, VA1+=+15 V, VA1-=-15 V, VA2=+24 V, VD2=+5 V, Vp=+5 V, VF=+12 V) Parameter*8 Cooling temperature Temperature control range Power dissipation of TE-cooler element Cool down time to reset temperature Setting temperature for overheat protection*9 Symbol Ts Min. -11 -0.05 - 'Ts Pp to To Typ. -10 +45 Max. -9 +0.05 7 5 - Unit °C °C W min °C *8: Other functions include error display, automatic power off, and detection of electrical opens and shorts by the thermosensor. *9: Temperature on the rear of the case (where the fan is installed) Spectral response (without window) (Typ. Ta=25 °C) 100 S7030/S7031 series 90 Quantum efficiency (%) 80 S11500-1007 70 60 50 40 30 20 Front-illuminated CCD 10 0 200 400 600 800 1000 1200 Wavelength (nm) KMPDB0038EB 3 CCD multichannel detector heads C7040, C7041 Dark current vs. temperature (Typ.) 1000 Dark current (e-/pixel/s) 100 10 1 0.1 0.01 -50 -40 -20 -30 -10 0 10 20 30 Temperature (°C) KMPDB0256EA Device structure (S7030/S7031 series) Thinning 23 21 15 20 13 14 2-bevel 22 24 1 n H 2 signal out 5 4 3 2 12345 4-bevel Thinning V 12 2 11 3 4 5 8 10 9 n Blank (4 pixels) Blank (4 pixels) 2 signal out 6-bevel V=58, 122, 250 H=512, 1024 6-bevel KMPDC0016EB 4 CCD multichannel detector heads C7040, C7041 Block diagram (C7041) P+ Vp (+5V) P.GND VD2 (+5V) D.GND PLED TH+ TH- F.GND Temp monitor Cooling control VD1 (+5V) D.GND VA1+ (+15V) VA1- (-15V) A.GND Temperature controller * TE-cooler OD RD OG IG1H, IG2H IG1V, IG2V P1V, P2V, TG P1H, P2H SG RG TH.H Regulator VA2 (+24V) Start CLK VEE VDD VF (+12V) Driver Timing generator EOS Trigger Mode select SS, ISV, ISH Buffer Data video OS Pre-amp CCD area image sensor S7031 series * The C7040 does not include the temperature controller and TE-cooler. Inverter Clamp Low-pass filter KACCC0078EB KACCC0078EB 5 CCD multichannel detector heads C7040, C7041 Timing chart (line binning operation) Start CLK P1V P2V TG P1H P2H SG RG Clamp EOS Trigger Data video V-ch1 H-ch10 H-ch11 V-ch2 H-ch(N-10) H-ch(N-9) V-ch(M) H-ch1 H-ch2 H-ch(N) M=64, 128, 256 N=532, 1044 V-ch1--V-ch2, V-ch (M-3)--V-ch (M): Isolation pixels H-ch1--H-ch4, H-ch (N-3)--H-ch (N): Blank pixels H-ch5--H-ch10, H-ch (N-9)--H-ch (N-4): Isolation pixels KACCC0079EC 6 CCD multichannel detector heads C7040, C7041 Pin connections of "SIGNAL I/O" connector 15-pin D-sub connector 8 7 15 6 14 5 13 4 12 3 11 2 10 1 9 KACCC0069EA Pin No. Terminal name 1 Mode select 2 3 4 5 Data video VA1+ (+15 V) VA1- (-15 V) VD1 (+5 V) 6 Start 7 CLK 8 EOS 9 10 11 12 13 14 15 A.GND A.GND VA2 (+24 V) D.GND D.GND D.GND Trigger Description Digital input signal used to select between the line binning operation and area scanning operation. HCMOS compatible. High level or left open: line binning operation Low level: area scanning operation Analog video output. Positive polarity. Analog power supply Analog power supply Digital power supply Digital input signal for initializing the circuit. HCMOS compatible. Positive logic. The interval of the Start pulses determines the integration time of the CCD image sensor. Digital input signal for operating the circuit. HCMOS compatible. Rising edge operation. Digital output signal for indicating end-of-scan of the image sensor. HCMOS compatible. Negative logic. Analog ground Analog ground Analog power supply Digital ground Digital ground Digital ground Digital output signal for A/D conversion. HCMOS compatible. Positive logic. Pin connections of "TE CONTROL I/O" connector (C7041) 9-pin D-sub connector 5 4 9 3 8 2 7 1 6 KACCC0075EA Pin No. 1 2 Terminal name VD2 (+5 V) Temp monitor 3 Cooling control 4 Vp (+5 V) 5 6 7 VF (+12 V) D.GND D.GND 8 P.GND 9 F.GND Description Digital power supply Analog output signal of the temperature of the CCD image sensor Digital input signal for starting to cool down. HCMOS compatible. High level or left open: cooling Low level: stand-by Power supply for the thermoelectric cooler in the CCD image sensor (Please use AWG 18 wire) Power supply for cooling fan Ground Ground Power supply return of the thermoelectric cooler mounted in the CCD image sensor (Please use AWG 18 wire) Power supply return for cooling fan Available for using same power supply (+5 V) for "+VD2" and "+Vp" Caution: Do not connect "VD2" and "Vp" together on the backside of the 9-pin D-sub connector. These may be connected (shorted) at the power supply end, not 9-pin D-sub connector. 7 CCD multichannel detector heads C7040, C7041 Dimensional outlines (unit: mm) C7040 0.5 0.3 34.0 2.7 Focal plane 11.0 62.0 82.0 50.0 60.0 80.0 90.0 100.0 Focal plane 50.0 (4 ) M3 depth 4 KACCA0062EC 35.0 C7041 34.0 2.4 0.5 Focal plane 77.0 62.0 Focal plane 11.0 82.0 50.0 60.0 80.0 90.0 100.0 50.0 (4 ) M3 depth 4 KACCA0063EC 8 CCD multichannel detector heads C7040, C7041 Pin connections TE controller Power supply Controller VF (+12V) F.GND VP (+5V) P.GND VD2 (+5V) D.GND 5 9 4 8 3 7 6 Cooling control D.GND 2 1 I/O signal Pulse generator Power supply CLK D.GND Start D.GND 15 14 13 VD1 (+5V) D.GND VA1+ (+15V) VA1- (-15V) VA2 (+24V) A.GND Controller Mode select D.GND S/H or A/D Analog input A.GND S/H input D.GND Oscilloscope CH1 GND Ext.Trig GND 12 11 10 9 8 7 6 5 4 3 2 1 KACCC0076EC Multichannel detector head controller C7557-01 When connected to a HAMAMATSU multichannel detector head and a personal computer, the C7557-01 allows easy control of the detector head and data acquisition by using dedicated software that comes with the unit. Suitable multichannel detector head C7020/-02, C7021/-02, C7025/-02, C7040, C7041, C7043, C7044, C7180, C7181, C8061-01, C8062-01, C10150, C10151, C5964 series, C8892 9 CCD multichannel detector heads C7040, C7041 Accessories · Spare fuse (2.5 A)*10 · AC cable · 2 to 3 conversion adapter · USB cable · Detector head connection cables (for “SIGNAL I/O” and “TE CONTROL I/O” terminal of multichannel detector head) · CD-R (MCD USB driver, software, operation manual) · MOS adapter*11 *10: Contained in the holder just above the AC cable connector on the C7557-01 rear panel. *11: When operating the NMOS multichannel detector head, always be sure to attach the MOS adapter (supplied) to the C7557-01 main unit. If the the NMOS multichannel detector head is connected and the power is turned on without attaching the adapter, the power supply in the C7557-01 main unit may be damaged. MOS ŢťŢűŵŦų MOS adapter mounting example Connection example Shutter * timing pulse AC cable (100 to 240 V; included with the C7557-01) Trig. POWER Dedicated cable (Included with the C7557-01) SIGNAL I/O USB cable (Included with the C7557-01) TE CONTROL I/O Image sensor + Multichannel detector head C7557-01 PC (Windows 2000/XP/Vista) (USB 2.0) KACCC0402EA Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. Type numbers of products listed in the specification sheets or supplied as samples may have a suffix “(X)” which means tentative specifications or a suffix “(Z)” which means developmental specifications. ©2010 Hamamatsu Photonics K.K. www.hamamatsu.com HAMAMATSU PHOTONICS K.K., Solid State Division 1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184 U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P.O.Box 6910, Bridgewater, N.J. 08807-0910, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218 Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 8152-375-0, Fax: (49) 8152-265-8 France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10 United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777 North Europe: Hamamatsu Photonics Norden AB: Smidesvägen 12, SE-171 41 Solna, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01 Italy: Hamamatsu Photonics Italia S.R.L.: Strada della Moia, 1 int. 6, 20020 Arese, (Milano), Italy, Telephone: (39) 02-935-81-733, Fax: (39) 02-935-81-741 Cat. No. KACC1034E14 Apr. 2010 DN 10