DVSA2800D Series HIGH RELIABILITY HYBRID DC-DC CONVERTERS DESCRIPTION FEATURES The DVSA series of high reliability DC-DC converters is operable over the full military (-55 °C to +125 °C) temperature range with no power derating. Unique to the DVSA series is a magnetic feedback circuit that is radiation immune. Operating at a nominal fixed frequency of 450 kHz, these regulated, isolated units utilize well controlled undervoltage lockout circuitry to eliminate slow start-up problems. • • • These converters are designed and manufactured in a facility qualified to ISO9001 and certified to MILPRF-38534 and MIL-STD-883. This product may incorporate one or more of the following U.S. patents: 5,784,266 5,790,389 5,963,438 5,999,433 6,005,780 6,084,792 6,118,673 • • • • • • • • • • • • • • • High Reliability Very Low Output Noise Wide Input Voltage Range: 15 to 50 Volts per MIL-STD-704 Up to 6 Watts Output Power Radiation Immune Magnetic Feedback Circuit NO Use of Optoisolators Undervoltage Lockout Indefinite Short Circuit Protection Current Limit Protection Industry Standard Pinout High Input Transient Voltage: 80 Volts for 1 sec per MIL-STD-704A Radiation Hardened Version Available Precision Projection Welded Hermetic Package High Power Density: > 19 W/in3 Custom Versions Available Additional Environmental Screening Available Meets MIL-STD-461C and MIL-STD-461D EMC Requirements When Used With a DVMA28 EMI Filter MIL-PRF-38534 Element Evaluated Components Figure 1 – DVSA2800D DC-DC Converter (Not To Scale) th 1X002DSG 11314 4 Avenue West, Suite 206 Everett, WA 98204 http://www.vpt-inc.com Sales Information: Phone: (425) 353-3010 Fax: (425) 353-4030 E-mail: [email protected] 1 DVSA2800D Series SPECIFICATIONS (TCASE = -55°C to +125°C, VIN = +28V ± 5%, Full Load5, Unless Otherwise Specified) ABSOLUTE MAXIMUM RATINGS Input Voltage (Continuous) Input Voltage (Transient, 1 second) Output Power1 Power Dissipation (Full Load, TCASE = +125°C) Parameter 50 VDC 80 Volts 6 Watts 2.5 Watts Junction Temperature Rise to Case Storage Temperature Lead Solder Temperature (10 seconds) Weight (Maximum) DVSA2805D Conditions Min Typ +10°C -65°C to +150°C 270°C 15 Grams DVSA2812D Units Max Min Typ Max STATIC Continuous INPUT 4 Voltage Current 15 28 50 15 28 50 V Transient, 1 sec - - 80 - - 80 V Inhibited - - 6 - - 6 mA No Load - 30 60 - 30 60 mA - 30 50 - 30 50 mAp-p 5 Ripple Current Full Load , 20Hz to 10MHz Inhibit Pin Input 4 Inhibit Pin Open Circuit Voltage 4 UVLO Turn On 4 UVLO Turn Off OUTPUT 5 Voltage 3,6 Current 3,6 Ripple Voltage Line Regulation Load Regulation Cross Regulation 0 - 1.5 V 9.0 11.0 13.0 V 12.0 - 14.8 12.0 - 14.8 V V 11.0 - 14.5 11.0 - 14.5 4.95 5.0 5.05 11.88 12.0 12.12 V +VOUT TCASE = -55°C to +125°C 4.925 5.0 5.075 11.82 12.0 12.18 V -VOUT TCASE = 25°C 4.80 5.0 5.20 11.80 12.0 12.20 V -VOUT TCASE = -55°C to +125°C 4.75 5.0 5.25 11.52 12.0 12.48 V 0 - 5 0 - 6 W - 3.5 0 - 4.2 W ±VOUT Either Output 0 ±VOUT Either Output 0 - 0.7 0 - 0.35 A ±VOUT Full Load , 20Hz to 10MHz - - 50 - - 50 mVp-p +VOUT VIN = 16V to 40V - 10 20 - 10 20 mV -VOUT VIN = 16V to 40V - 50 200 - 50 200 mV +VOUT No Load to Full Load 5 - 10 50 - 10 50 mV 5,7 5 -VOUT No Load to Full Load - 50 200 - 50 200 mV -VOUT +Load 70%, -Load 30% +Load 30%, -Load 70% - - 450 - - 450 mV 5 66 72 - 72 77 - % 4 - - 3 - - 3 W Full Load LOAD FAULT POWER DISSIPATION 4 1.5 13.0 TCASE = 25°C EFFICIENCY CAPACITIVE LOAD 11.0 +VOUT Total Power 0 9.0 Overload Short Circuit - - 3 - - 3 W Either Output - - 500 - - 500 µF 350 450 500 350 450 500 kHz 100 - - 100 - - MΩ - 457 - - 457 - kHrs SWITCHING FREQUENCY ISOLATION 500 VDC, TCASE = 25°C MTBF (MIL-HDBK-217F) AIF @ TC = 55°C See notes next page. 1X002DSG 2 DVSA2800D Series SPECIFICATIONS (TCASE = -55°C to +125°C, VIN = +28V ± 5%, Full Load5, Unless Otherwise Specified) ABSOLUTE MAXIMUM RATINGS Input Voltage (Continuous) Input Voltage (Transient, 1 second) Output Power1 Power Dissipation (Full Load, TCASE = +125°C) Parameter 50 VDC 80 Volts 6 Watts 2.5 Watts Junction Temperature Rise to Case Storage Temperature Lead Solder Temperature (10 seconds) Weight (Maximum) DVSA2805D Conditions +10°C -65°C to +150°C 270°C 15 Grams DVSA2812D Units Min Typ Max Min Typ Max - - 300 - - 300 DYNAMIC Load Step Output Transient ±VOUT 2 Load Step Recovery Line Step Output Transient 4 ±VOUT 2, 4 Line Step Recovery Turn On Delay Turn On Overshoot Notes: 1. 2. 3. 4. 5. 6. 7. ±VOUT Half Load to Full Load VIN = 16V to 40V VIN = 0V to 28V mVPK - - 400 - - 450 µSec - 500 1000 - 600 1200 mVPK - 300 700 - 300 500 µSec - 10 20 - 10 20 mSec - - 25 - - 50 mVPK Dependant on output voltage. Time for output voltage to settle within 1% of its nominal value. Derate linearly to 0 at 135°C. Verified by qualification testing. Half load at +VOUT and half load at –VOUT. Up to 70% of the total power or current can be drawn from any one of the two outputs. 5% Load to Full Load at -55°C. 1X002DSG 3 DVSA2800D Series SPECIFICATIONS (TCASE = -55°C to +125°C, VIN = +28V ± 5%, Full Load5, Unless Otherwise Specified) ABSOLUTE MAXIMUM RATINGS Input Voltage (Continuous) Input Voltage (Transient, 1 second) Output Power1 Power Dissipation (Full Load, TCASE = +125°C) Parameter 50 VDC 80 Volts 6 Watts 2.5 Watts Junction Temperature Rise to Case Storage Temperature Lead Solder Temperature (10 seconds) Weight (Maximum) DVSA2815D Conditions +10°C -65°C to +150°C 270°C 15 Grams Units Min Typ Max STATIC Continuous INPUT 4 Voltage Current 15 28 50 V Transient, 1 sec - - 80 V Inhibited - - 6 mA No Load - 30 60 mA - 30 50 mAp-p 5 Ripple Current Full Load , 20Hz to 10MHz Inhibit Pin Input 4 Inhibit Pin Open Circuit Voltage 4 UVLO Turn On 4 UVLO Turn Off OUTPUT 5 Voltage 3,6 Current 3,6 Ripple Voltage Line Regulation Load Regulation Cross Regulation V V 12.0 - 14.8 V V 11.0 - 14.5 14.85 15.0 15.15 V +VOUT TCASE = -55°C to +125°C 14.775 15.0 15.225 V -VOUT TCASE = 25°C 14.80 15.0 15.20 V -VOUT TCASE = -55°C to +125°C 14.40 15.0 15.60 V - - 6 W - - 4.2 W ±VOUT Either Output ±VOUT Either Output - - 0.28 A ±VOUT Full Load , 20Hz to 10MHz - - 50 mVp-p +VOUT VIN = 16V to 40V - 10 20 mV -VOUT VIN = 16V to 40V - 50 200 mV +VOUT No Load to Full Load 5 - 10 50 mV -VOUT No Load to Full Load 5,7 - 50 200 mV -VOUT +Load 70%, -Load 30% +Load 30%, -Load 70% - - 450 mV 5 73 79 - % 4 - - 3 W Short Circuit - - 3 W Either Output - - 500 µF 350 450 500 kHz 100 - - MΩ - 457 - kHrs 5 Full Load LOAD FAULT POWER DISSIPATION 4 1.5 13.0 TCASE = 25°C EFFICIENCY CAPACITIVE LOAD 11.0 +VOUT Total Power 0 9.0 Overload SWITCHING FREQUENCY ISOLATION 500 VDC, TCASE = 25°C MTBF (MIL-HDBK-217F) AIF @ TC = 55°C See notes next page. 1X002DSG 4 DVSA2800D Series SPECIFICATIONS (TCASE = -55°C to +125°C, VIN = +28V ± 5%, Full Load5, Unless Otherwise Specified) ABSOLUTE MAXIMUM RATINGS Input Voltage (Continuous) Input Voltage (Transient, 1 second) Output Power1 Power Dissipation (Full Load, TCASE = +125°C) Parameter 50 VDC 80 Volts 6 Watts 2.5 Watts Junction Temperature Rise to Case Storage Temperature Lead Solder Temperature (10 seconds) Weight (Maximum) DVSA2815D Conditions +10°C -65°C to +150°C 270°C 15 Grams Units Min Typ Max - - 300 DYNAMIC Load Step Output Transient ±VOUT 2 Load Step Recovery Line Step Output Transient 4 ±VOUT 2, 4 Line Step Recovery Turn On Delay Turn On Overshoot Notes: 1. 2. 3. 4. 5. 6. 7. ±VOUT Half Load to Full Load VIN = 16V to 40V VIN = 0V to 28V mVPK - - 500 µSec - 500 1200 mVPK - 300 500 µSec - 10 20 mSec - - 50 mVPK Dependant on output voltage. Time for output voltage to settle within 1% of its nominal value. Derate linearly to 0 at 135°C. Verified by qualification testing. Half load at +VOUT and half load at –VOUT. Up to 70% of the total power or current can be drawn from any one of the two outputs. 5% Load to Full Load at -55°C. 1X002DSG 5 DVSA2800D Series BLOCK DIAGRAM D2 PIN 1 +V OUT C3 T1 Rs3 OUT COM D1 Rs2 PIN 2 PIN 6 C2 28V IN L1 C1 PIN 3 -V OUT IN COM PIN 7 Q1 MAGNETIC FEEDBACK UNDER VOLTAGE SHUTDOWN PRIMARY HOUSEKEEPING SUPPLY VOLTAGE AND CURRENT AMPLIFIERS Rs1 PWM CONTROL SECONDARY HOUSEKEEPING SUPPLY INH PIN 5 Figure 2 CONNECTION DIAGRAM 6 1 28V IN 28 Vdc + - +V OUT LOAD 5 2 INH OUT COM LOAD 7 3 IN COM -V OUT Figure 3 1X002DSG 6 DVSA2800D Series INHIBIT DRIVE CONNECTION DIAGRAMS 28V IN 6 28V IN 6 10K INH 5 10K OPTOISOLATOR BIAS OPTIONAL CAPACITOR INH 5 BIAS OPTIONAL CAPACITOR 12V IN COM 7 12V IN COM 7 Figure 4 – Internal Inhibit Circuit and Recommended Drive Figure 5 – Isolated Inhibit Drive (Shown with optional capacitor for turn-on delay) (Shown with optional capacitor for turn-on delay) EMI FILTER HOOKUP DIAGRAM DVSA2800D DC-DC CONVERTER DVMA28 EMI FILTER 1 2 28V IN 6 28V OUT 1 28V IN +V OUT LOAD 28 Vdc 5 + - 2 INH OUT COM LOAD 5 4 7 IN COM OUT COM 3 3 IN COM CASE -V OUT 8 Figure 6 – Converter with EMI Filter 1X002DSG 7 DVSA2800D Series EFFICIENCY PERFORMANCE CURVES (TCASE = 25°C, Full Load, Unless Otherwise Specified) VIN = 28V VIN = 50V 80 70 70 60 60 Output Power (W) 6 0 5 0 4 10 3 10 2 20 1 20 5 30 4 30 40 2 40 50 1 50 0 Efficiency (%) 80 0 Efficiency (%) VIN = 15V Output Power (W) Figure 7 – DVSA2805D Figure 8 – DVSA2812D Efficiency (%) vs. Output Power (W) Efficiency (%) vs. Output Power (W) 80 70 Efficiency (%) 60 50 40 30 20 6 5 4 2 1 0 0 10 Output Power (W) Figure 9 – DVSA2815D Efficiency (%) vs. Output Power (W) 1X002DSG 8 DVSA2800D Series EMI PERFORMANCE CURVES (TCASE = 25°C, VIN = +28V ± 5%, Full Load, Unless Otherwise Specified) Figure 10 – DVSA2800D without EMI Filter Figure 11 – DVSA2800D with EMI Filter 1X002DSG 9 DVSA2800D Series PACKAGE SPECIFICATIONS TOP VIEW SIDE VIEW PIN FUNCTION 1 +V OUT 2 OUT COM 3 -V OUT 4 N/C 5 INHIBIT 6 28V IN 7 IN COM 8 CASE BOTTOM VIEW Figure 12 – Package and Pinout (Dimensional Limits are ±0.005” Unless Otherwise Stated) 1X002DSG 10 DVSA2800D Series PACKAGE PIN DESCRIPTION Pin Function Description 1 +V OUT Positive Output Voltage Connection 2 OUT COM Output Common Connection 3 -V OUT Negative Output Voltage Connection 4 N/C No Connection 5 INHIBIT Logic Low = Disabled Output. Connecting the inhibit pin to input common causes converter shutdown. Logic High = Enabled Output. Unconnected or open collector TTL. 6 28V IN Positive Input Voltage Connection 7 IN COM Input Common Connection 8 CASE Case Connection 1X002DSG 11 DVSA2800D Series ENVIRONMENTAL SCREENING (100% Tested Per MIL-STD-883 as referenced to MIL-PRF-38534) Screening MIL-STD-883 (No Suffix) Extended /ES HB /HB Class H /H Class K /K • • • • • • • • • • • • • • Standard NonDestructive Bond Pull Method 2023 • Internal Visual Method 2017, 2032 Internal Procedure • Temperature Cycling Method 1010, Condition C Method 1010, -55°C to 125°C • Constant Acceleration Method 2001, 3000g, Y1 Direction Method 2001, 500g, Y1 Direction • PIND Method 2020, Condition A2 • Pre Burn-In Electrical 100% at 25°C • Burn-In Method 1015, 320 hours at +125°C Method 1015, 160 hours at +125°C 96 hours at +125°C 24 hours at +125°C • Final Electrical MIL-PRF-38534, Group A1 100% at 25°C • Hermeticity Method 1014, Fine Leak, Condition A Method 1014, Gross Leak, Condition C -3 Dip (1 x 10 ) Radiography Method 20123 External Visual Method 2009 Notes: 1X002DSG 1. 2. 3. • • • • • • • • • • • • • • • • • • • • • • • 100% R&R testing at –55°C, +25°C, and +125°C with all test data included in product shipment. PIND test Certificate of Compliance included in product shipment. Radiographic test Certificate of Compliance and film(s) included in product shipment. 12 DVSA2800D Series ORDERING INFORMATION DVSA 28 05 D R /HB 1 2 3 4 5 6 - XXX 7 (1) (2) (3) (4) Product Series Nominal Input Voltage Output Voltage Number of Outputs DVSA 28 1. 2. 3. 05 12 15 ± 5 Volts ± 12 Volts ± 15 Volts D (5) (6) (7) Rad-Hard Option2 Screening Code1,3 Additional Screening Code None R Notes: 28 Volts Standard 100 kRad None /ES /HB /H /K Standard Extended HB Class H Class K Dual Contact Sales Contact the VPT Inc. Sales Department for availability of Class H (/H) or Class K (/K) qualified products. VPT Inc. is not currently qualified to a DSCC certified radiation hardness assurance program. VPT Inc. reserves the right to ship higher screened or SMD products to meet lower screened orders at our sole discretion unless specifically forbidden by customer contract. Please contact your sales representative or the VPT Inc. Sales Department for more information concerning additional environmental screening and testing, different input voltage, output voltage, power requirement, source inspection, and/or special element evaluation for space or other higher quality applications. 1X002DSG 13 DVSA2800D Series SMD (STANDARD MICROCIRCUIT DRAWING) NUMBERS Standard Microcircuit Drawing (SMD) DVSA2800D Series Similar Part Number 5962-0324201HXC DVSA2805D/H 5962-0324202HXC DVSA2812D/H 5962-0324203HXC DVSA2815D/H Do not use the DVSA2800D Series similar part number for SMD product acquisition. It is listed for reference only. For exact specifications for the SMD product, refer to the SMD drawing. SMD’s can be downloaded from the DSCC website at http://www.dscc.dla.mil/programs/smcr/. The SMD number listed above is for MIL-PRF-38534 Class H screening, standard gold plated lead finish, and no RHA (Radiation Hardness Assurance) level. Please reference the SMD for other screening levels, lead finishes, and radiation levels. CONTACT INFORMATION To request a quotation or place orders please contact your sales representative or the VPT Inc. Sales Department at: Phone: Fax: E-mail: (425) 353-3010 (425) 353-4030 [email protected] All information contained in this datasheet is believed to be accurate, however, no responsibility is assumed for possible errors or omissions. The products or specifications contained herein are subject to change without notice. 1X002DSG 14