AD ADA4930-1 Ultralow noise drivers for low voltage adc Datasheet

Ultralow Noise
Drivers for Low Voltage ADCs
ADA4930-1/ADA4930-2
Data Sheet
13 –VS
ADA4930-1
–FB 1
12 PD
+IN 2
11 –OUT
–IN 3
10 +OUT
9
09209-001
VOCM
+VS 8
+VS 7
+VS 6
+VS 5
+FB 4
19 –OUT1
20 PD1
21 –VS1
23 –FB1
22 –VS1
24 +IN1
Figure 1.
18 +OUT1
17 VOCM1
–IN1 1
+FB1 2
+VS1 3
16 –VS2
15 –VS2
ADA4930-2
+VS1 4
14 PD2
13 –OUT2
–FB2 5
09209-002
+OUT2 12
VOCM2 11
+VS2 10
–IN2 7
+FB2 8
+VS2 9
+IN2 6
Figure 2.
APPLICATIONS
100
ADC drivers
Single-ended-to-differential converters
IF and baseband gain blocks
Differential buffers
Line drivers
VN (nV/√hz)
10
The ADA4930-1/ADA4930-2 are very low noise, low distortion,
high speed differential amplifiers. They are an ideal choice for
driving 1.8 V high performance ADCs with resolutions up to
14 bits from dc to 70 MHz. The adjustable output common
mode allows the ADA4930-1/ADA4930-2 to match the input of
the ADC. The internal common-mode feedback loop provides
exceptional output balance, suppression of even-order harmonic
distortion products, and dc level translation.
With the ADA4930-1/ADA4930-2, differential gain configurations
are easily realized with a simple external feedback network of
four resistors determining the closed-loop gain of the amplifier.
The ADA4930-1/ADA4930-2 are fabricated using Analog Devices,
Inc., proprietary silicon-germanium (SiGe), complementary
bipolar process, enabling them to achieve very low levels of
distortion with an input voltage noise of only 1.2 nV/√Hz.
1
0
10
100
1k
10k
100k
1M
10M
FREQUENCY (Hz)
100M
09209-003
GENERAL DESCRIPTION
Rev. C
14 –VS
Low input voltage noise: 1.2 nV/√Hz
Low common-mode output: 0.9 V on single supply
Extremely low harmonic distortion
−104 dBc HD2 at 10 MHz
−79 dBc HD2 at 70 MHz
−73 dBc HD2 at 100 MHz
−101 dBc HD3 at 10 MHz
−82 dBc HD3 at 70 MHz
−75 dBc HD3 at 100 MHz
High speed
−3 dB bandwidth of 1.35 GHz, G = 1
Slew rate: 3400 V/μs, 25% to 75%
0.1 dB gain flatness to 380 MHz
Fast overdrive recovery of 1.5 ns
0.5 mV typical offset voltage
Externally adjustable gain
Differential-to-differential or single-ended-to-differential
operation
Adjustable output common-mode voltage
Single-supply operation: 3.3 V or 5 V
15 –VS
FUNCTIONAL BLOCK DIAGRAMS
16 –VS
FEATURES
Figure 3. Voltage Noise Spectral Density
The low dc offset and excellent dynamic performance of the
ADA4930-1/ADA4930-2 make them well suited for a wide
variety of data acquisition and signal processing applications.
The ADA4930-1 is available in a Pb-free, 3 mm × 3 mm 16-lead
LFCSP, and the ADA4930-2 is available in a Pb-free, 4 mm × 4 mm
24-lead LFCSP. The pinout has been optimized to facilitate printed
circuit board (PCB) layout and minimize distortion. The
ADA4930-1 is specified to operate over the −40°C to +105°C
temperature range, and the ADA4930-2 is specified to operate over
the −40°C to +105°C temperature range for 3.3 V or 5 V supply
voltages.
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2010–2017 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADA4930-1/ADA4930-2
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Test Circuits ..................................................................................... 15
Applications ....................................................................................... 1
Operational Description ................................................................ 16
General Description ......................................................................... 1
Definition of Terms .................................................................... 16
Functional Block Diagrams ............................................................. 1
Theory of Operation ...................................................................... 17
Revision History ............................................................................... 2
Analyzing an Application Circuit ............................................ 17
Specifications..................................................................................... 3
Setting the Closed-Loop Gain .................................................. 17
3.3 V Operation ............................................................................ 3
Estimating the Output Noise Voltage ...................................... 17
3.3 V VOCM to VO, cm Performance ............................................... 4
Impact of Mismatches in the Feedback Networks ................. 18
3.3 V General Performance ......................................................... 4
Input Common-Mode Voltage Range ..................................... 18
5 V Operation ............................................................................... 5
Minimum RG Value .................................................................... 19
5 V VOCM to VO, cm Performance .................................................. 6
Setting the Output Common-Mode Voltage .......................... 19
5 V General Performance ............................................................ 6
Calculating the Input Impedance for an Application Circuit
....................................................................................................... 19
Absolute Maximum Ratings............................................................ 7
Thermal Resistance ...................................................................... 7
Maximum Power Dissipation ..................................................... 7
ESD Caution .................................................................................. 7
Pin Configurations and Function Descriptions ........................... 8
Layout, Grounding, and Bypassing .............................................. 23
High Performance ADC Driving ................................................. 24
Outline Dimensions ....................................................................... 25
Ordering Guide .......................................................................... 25
Typical Performance Characteristics ............................................. 9
REVISION HISTORY
5/2017—Rev. B to Rev. C
Changes to Figure 5 and Figure 6 ........................................................... 8
Changes to Input Common-Mode Adjustment with DC Biased
Source Section .......................................................................................... 21
Changes to High Performance ADC Driving Section
and Figure 60 .................................................................................... 24
Updated Outline Dimensions ....................................................... 25
Changes to Ordering Guide .......................................................... 25
1/2015—Rev. A to Rev. B
Updated Outline Dimensions ....................................................... 25
Changes to Ordering Guide .......................................................... 25
10/2010—Rev. 0 to Rev. A
Changes to General Description Section .......................................1
10/2010—Revision 0: Initial Version
Rev. C | Page 2 of 25
Data Sheet
ADA4930-1/ADA4930-2
SPECIFICATIONS
3.3 V OPERATION
VS = 3.3 V, VICM = 0.9 V, VOCM = 0.9 V, RF = 301 Ω, RG = 301 Ω, RL, dm = 1 kΩ, single-ended input, differential output, TA = 25°C, TMIN to
TMAX = −40°C to +105°C, unless otherwise noted.
Table 1.
Parameter
DYNAMIC PERFORMANCE
−3 dB Small Signal Bandwidth
−3 dB Large Signal Bandwidth
Bandwidth for 0.1 dB Flatness
ADA4930-1
ADA4930-2
Slew Rate
Settling Time to 0.1%
Overdrive Recovery Time
NOISE/HARMONIC PERFORMANCE
HD2/HD3
Third-Order IMD
Input Voltage Noise
Input Current Noise
Crosstalk
DC PERFORMANCE
Input Offset Voltage
Input Offset Voltage Drift
Input Bias Current
Input Bias Current Drift
Input Offset Current
Open-Loop Gain
INPUT CHARACTERISTICS
Input Common-Mode Voltage Range
Input Resistance
Input Capacitance
CMRR
OUTPUT CHARACTERISTICS
Output Voltage
Linear Output Current
Output Balance Error
Test Conditions/Comments
Min
VO, dm = 0.1 V p-p
VO, dm = 2 V p-p
VO, dm = 0.1 V p-p
Typ
Max
Unit
1430
887
MHz
MHz
VO, dm = 2 V step, 25% to 75%
VO, dm = 2 V step, RL = 200 Ω
G = 3, VIN, dm = 0.7 V p-p pulse
380
89
2877
6.3
1.5
MHz
MHz
V/µs
ns
ns
VO, dm = 2 V p-p, fC = 10 MHz
VO, dm = 2 V p-p, fC = 30 MHz
VO, dm = 2 V p-p, fC = 70 MHz
VO, dm = 2 V p-p, fC = 100 MHz
VO, dm = 1 V p-p/tone, fC = 70.05 MHz ± 0.05 MHz
VO, dm = 1 V p-p/tone, fC = 140.05 MHz ± 0.05 MHz
f = 100 kHz
f = 100 kHz
f = 100 MHz, ADA4930-2, RL = 200 Ω
−98/−97
−91/−88
−79/−79
−73/−73
91
86
1.15
3
−90
dB
dB
dB
dB
dBc
dBc
nV/√Hz
pA/√Hz
dB
VIP = VIN = VOCM = 0 V, RL = open circuit
TMIN to TMAX
−3.1
−36
TMIN to TMAX
−1.8
RF = RG = 10 kΩ, ΔVO = 0.5 V, RL = open circuit
−0.5
2.75
−24
−0.05
+0.1
64
0.3
Differential
Common mode
Common mode
ΔVICM = 0.5 V dc; RF = RG = 10 kΩ, RL = open circuit
Each single-ended output; RF = RG = 10 kΩ
Each single-ended output; f = 1 MHz, TDH ≤ 60 dBc
f = 1 MHz
Rev. C | Page 3 of 25
+3.1
−16
+1.8
1.2
150
3
1
−82
0.11
−77
1.74
30
55
mV
µV/°C
µA
µA/°C
µA
dB
V
kΩ
MΩ
pF
dB
V
mA
dB
ADA4930-1/ADA4930-2
Data Sheet
3.3 V VOCM TO VO, CM PERFORMANCE
Table 2.
Parameter
VOCM DYNAMIC PERFORMANCE
−3 dB Bandwidth
Slew Rate
VOCM INPUT CHARACTERISTICS
Input Voltage Range
Input Resistance
Input Offset Voltage
Input Voltage Noise
Gain
CMRR
Test Conditions/Comments
Min
Typ
VO, cm = 0.1 V p-p
VO, cm = 2 V p-p, 25% to 75%
VOS, cm = VO, cm − VOCM; VIP = VIN = VOCM = 0 V
f = 100 kHz
Max
745
828
0.8
7.0
−25
MHz
V/µs
1.1
10.3
+31
8.3
+15.4
23.5
1
−83
0.99
ΔVOCM = 0.5 V dc; RF = RG = 10 kΩ, RL = open circuit
Unit
1.02
−77
V
kΩ
mV
nV/√Hz
V/V
dB
3.3 V GENERAL PERFORMANCE
Table 3.
Parameter
POWER SUPPLY
Operating Range
Quiescent Current per Amplifier
+PSRR
−PSRR
POWER-DOWN (PD)
PD Input Voltage
Turn-Off Time
Turn-On Time
PD Pin Bias Current
Enabled
Disabled
Test Conditions/Comments
Min
Enabled
Enabled, TMIN to TMAX variation
Disabled
ΔVICM = 0.5 V; RF = RG = 10 kΩ, RL = open circuit
ΔVICM = 0.5 V; RF = RG = 10 kΩ, RL = open circuit
32
0.44
Typ
3.3
35
81
1.8
−74
−87
Max
40
2.35
−70
−76
Unit
V
mA
µA/°C
mA
dB
dB
Disabled
Enabled
<0.8
>1.3
1
12
V
V
µs
ns
PD = 3.3 V
PD = 0 V
0.09
97
µA
µA
OPERATING TEMPERATURE RANGE
−40
Rev. C | Page 4 of 25
+105
°C
Data Sheet
ADA4930-1/ADA4930-2
5 V OPERATION
VS = 5 V, VICM = 0.9 V, VOCM = 0.9 V, RF = 301 Ω, RG = 301 Ω, RL, dm = 1 kΩ, single-ended input, differential output, TA= 25°C,
TMIN to TMAX = −40°C to +105°C, unless otherwise noted.
Table 4.
Parameter
DYNAMIC PERFORMANCE
−3 dB Small Signal Bandwidth
−3 dB Large Signal Bandwidth
Bandwidth for 0.1 dB Flatness
ADA4930-1
ADA4930-2
Slew Rate
Settling Time to 0.1%
Overdrive Recovery Time
NOISE/HARMONIC PERFORMANCE
HD2/HD3
Third-Order IMD
Input Voltage Noise
Input Current Noise
Crosstalk
DC PERFORMANCE
Input Offset Voltage
Input Offset Voltage Drift
Input Bias Current
Input Bias Current Drift
Input Offset Current
Open-Loop Gain
INPUT CHARACTERISTICS
Input Common-Mode Voltage Range
Input Resistance
Input Capacitance
CMRR
OUTPUT CHARACTERISTICS
Output Voltage
Linear Output Current
Output Balance Error
Test Conditions/Comments
Min
VO, dm = 0.1 V p-p
VO, dm = 2 V p-p
VO, dm = 0.1 V p-p
Typ
Max
Unit
1350
937
MHz
MHz
VO, dm = 2 V step, 25% to 75%
VO, dm = 2 V step, RL = 200 Ω
G = 3, VIN, dm = 0.7 V p-p pulse
369
90
3400
6
1.5
MHz
MHz
V/µs
ns
ns
VO, dm = 2 V p-p, fC = 10 MHz
VO, dm = 2 V p-p, fC = 30 MHz
VO, dm = 2 V p-p, fC = 70 MHz
VO, dm = 2 V p-p, fC = 100 MHz
VO, dm = 1 V p-p/tone, fC = 70.05 MHz ± 0.05 MHz
VO, dm = 1 V p-p/tone, fC = 140.05 MHz ± 0.05 MHz
f = 100 kHz
f = 100 kHz
f = 100 MHz, ADA4930-2, RL = 200 Ω
−104/−101
−91/−93
−79/−82
−73/−75
94
90
1.2
2.8
−90
dB
dB
dB
dB
dBc
dBc
nV/√Hz
pA/√Hz
dB
VIP = VIN = VOCM = 0 V, RL = open circuit
TMIN to TMAX
−3.1
−34
TMIN to TMAX
−0.82
RF = RG = 10 kΩ, ΔVO = 1 V, RL = open circuit
−0.15
1.8
−23
−0.05
+0.1
64
0.3
Differential
Common mode
Common mode
ΔVICM = 1 V dc; RF = RG = 10 kΩ, RL = open circuit
Each single-ended output; RF = RG = 10 kΩ
Each single-ended output; f = 1 MHz, TDH ≤ 60 dBc
f = 1 MHz
Rev. C | Page 5 of 25
+3.1
−15
+0.82
2.8
150
3
1
−82
0.18
−77
3.38
30
55
mV
µV/°C
µA
µA/°C
µA
dB
V
kΩ
MΩ
pF
dB
V
mA
dB
ADA4930-1/ADA4930-2
Data Sheet
5 V VOCM TO VO, CM PERFORMANCE
Table 5.
Parameter
VOCM DYNAMIC PERFORMANCE
−3 dB Bandwidth
Slew Rate
VOCM INPUT CHARACTERISTICS
Input Voltage Range
Input Resistance
Input Offset Voltage
Input Voltage Noise
Gain
CMRR
Test Conditions/Comments
Min
Typ
VO, cm = 0.1 V p-p
VO, cm = 2 V p-p, 25% to 75%
VOS, cm = VO, cm − VOCM; VIP = VIN = VOCM = 0 V
f = 100 kHz
Max
740
1224
0.5
7.0
−25
8.3
+0.35
23.5
1
−80
0.99
ΔVOCM = 1.5 V; RF = RG = 10 kΩ, RL = open circuit
Unit
MHz
V/µs
2.3
10.2
+15
1.02
−77
V
kΩ
mV
nV/√Hz
V/V
dB
5 V GENERAL PERFORMANCE
Table 6.
Parameter
POWER SUPPLY
Operating Range
Quiescent Current per Amplifier
+PSRR
−PSRR
POWER-DOWN (PD)
PD Input Voltage
Turn-Off Time
Turn-On Time
PD Pin Bias Current
Enabled
Disabled
Test Conditions/Comments
Min
Enabled
Enabled, TMIN to TMAX variation
Disabled
ΔVICM = 1 V; RF = RG = 10 kΩ, RL = open circuit
ΔVICM = 1 V; RF = RG = 10 kΩ, RL = open circuit
31.1
0.45
Typ
5
34
74.5
1.8
−74
−91
Max
38.4
2.6
−71
−75
Unit
V
mA
µA/°C
mA
dB
dB
Disabled
Enabled
<2.5
>3
1
12
V
V
µs
ns
PD = 5 V
PD = 0 V
0.09
97
µA
µA
OPERATING TEMPERATURE RANGE
−40
Rev. C | Page 6 of 25
+105
°C
Data Sheet
ADA4930-1/ADA4930-2
ABSOLUTE MAXIMUM RATINGS
Rating
5.5 V
See Figure 4
−65°C to +125°C
−40°C to +105°C
300°C
150°C
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
THERMAL RESISTANCE
θJA is specified for the device (including exposed pad) soldered
to a high thermal conductivity 2s2p circuit board, as described
in EIA/JESD51-7.
Airflow increases heat dissipation, effectively reducing θJA. In
addition, more metal directly in contact with the package leads/
exposed pad from metal traces, through holes, ground, and
power planes reduces θJA.
Figure 4 shows the maximum safe power dissipation vs. the
ambient temperature for the ADA4930-1 single 16-lead LFCSP
(98°C/W) and the ADA4930-2 dual 24-lead LFCSP (67°C/W)
on a JEDEC standard 4-layer board.
3.5
Table 8. Thermal Resistance
Package Type
16-Lead LFCSP (Exposed Pad)
24-Lead LFCSP (Exposed Pad)
θJA
98
67
Unit
°C/W
°C/W
MAXIMUM POWER DISSIPATION
The maximum safe power dissipation in the ADA4930-1/
ADA4930-2 packages is limited by the associated rise in
junction temperature (TJ) on the die. At approximately 150°C,
which is the glass transition temperature, the plastic changes its
properties. Even temporarily exceeding this temperature limit
can change the stresses that the package exerts on the die,
permanently shifting the parametric performance of the
ADA4930-1/ADA4930-2. Exceeding a junction temperature of
150°C for an extended period can result in changes in the
silicon devices, potentially causing failure.
3.0
2.5
ADA4930-2
2.0
1.5
ADA4930-1
1.0
0.5
0
–40 –30 –20 –10 0
10 20 30 40 50 60 70 80 90 100 110
TEMPERATURE (°C)
Figure 4. Maximum Power Dissipation vs. Ambient Temperature,
4-Layer Board
ESD CAUTION
Rev. C | Page 7 of 25
09209-004
Parameter
Supply Voltage
Power Dissipation
Storage Temperature Range
Operating Temperature Range
Lead Temperature (Soldering, 10 sec)
Junction Temperature
The power dissipated in the package (PD) is the sum of the
quiescent power dissipation and the power dissipated in the
package due to the load drive. The quiescent power is the voltage
between the supply pins (VS) times the quiescent current (IS).
The power dissipated due to the load drive depends upon the
particular application. The power due to load drive is calculated
by multiplying the load current by the associated voltage drop
across the device. RMS voltages and currents must be used in
these calculations.
MAXIMUM POWER DISSIPATION (W)
Table 7.
ADA4930-1/ADA4930-2
Data Sheet
ADA4930-1
11 –OUT
–IN 3
TOP VIEW
(Not to Scale)
10 +OUT
+FB1 2
+VS1 3
9
+VS1 4
VOCM
20 PD1
16 –V S2
TOP VIEW
(Not to Scale)
15 –V S2
14 PD2
13 –OUT2
+OUT2 12
VOCM2 11
–IN2 7
09209-005
+VS2 10
+IN2 6
+VS 8
+VS 7
+VS 6
+VS 5
19 –OUT1
ADA4930-2
–FB2 5
NOTES
1. EXPOSED PADDLE. THE EXPOSED PAD IS NOT
ELECTRICALLY CONNECTED TO THE DEVICE. IT IS
TYPICALLY SOLDERED TO GROUND OR A POWER
PLANE ON THE PCB THAT IS THERMALLY CONDUCTIVE.
21 –V S1
18 +OUT1
17 VOCM1
+FB2 8
+VS2 9
+FB 4
22 –V S1
–IN1 1
+IN 2
NOTES
1. EXPOSED PADDLE. THE EXPOSED PAD IS NOT
ELECTRICALLY CONNECTED TO THE DEVICE. IT IS
TYPICALLY SOLDERED TO GROUND OR A POWER
PLANE ON THE PCB THAT IS THERMALLY CONDUCTIVE.
Figure 5. ADA4930-1 Pin Configuration
09209-006
12 PD
–FB 1
23 –FB1
24 +IN1
13 –VS
14 –VS
15 –VS
16 –VS
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
Figure 6. ADA4930-2 Pin Configuration
Table 9. ADA4930-1 Pin Function Descriptions
Table 10. ADA4930-2 Pin Function Descriptions
Pin No.
1
Mnemonic
−FB
2
3
4
+IN
−IN
+FB
5 to 8
9
10
11
12
13 to 16
+VS
VOCM
+OUT
−OUT
PD
−VS
EPAD
Pin No.
1
2
3, 4
5
6
7
8
9, 10
11
12
13
14
15, 16
17
18
19
20
21, 22
23
24
Description
Negative Output for Feedback
Component Connection.
Positive Input Summing Node.
Negative Input Summing Node.
Positive Output for Feedback
Component Connection.
Positive Supply Voltage.
Output Common-Mode Voltage.
Positive Output for Load Connection.
Negative Output for Load Connection.
Power-Down Pin.
Negative Supply Voltage.
Exposed Paddle. The exposed pad is not
electrically connected to the device. It is
typically soldered to ground or a power
plane on the PCB that is thermally
conductive.
Rev. C | Page 8 of 25
Mnemonic
−IN1
+FB1
+VS1
−FB2
+IN2
−IN2
+FB2
+VS2
VOCM2
+OUT2
−OUT2
PD2
−VS2
VOCM1
+OUT1
−OUT1
PD1
−VS1
−FB1
+IN1
EPAD
Description
Negative Input Summing Node 1.
Positive Output Feedback Pin 1.
Positive Supply Voltage 1.
Negative Output Feedback Pin 2.
Positive Input Summing Node 2.
Negative Input Summing Node 2.
Positive Output Feedback Pin 2.
Positive Supply Voltage 2.
Output Common-Mode Voltage 2.
Positive Output 2.
Negative Output 2.
Power-Down Pin 2.
Negative Supply Voltage 2.
Output Common-Mode Voltage 1.
Positive Output 1.
Negative Output 1.
Power-Down Pin 1.
Negative Supply Voltage 1.
Negative Output Feedback Pin 1.
Positive Input Summing Node 1.
Exposed Paddle. The exposed pad is
not electrically connected to the
device. It is typically soldered to
ground or a power plane on the PCB
that is thermally conductive.
Data Sheet
ADA4930-1/ADA4930-2
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25°C, VS = 5 V, VICM = 0.9 V, VOCM = 0.9 V, RL, dm = 1 kΩ, unless otherwise noted.
3
3
VIN = 2V p-p
G = 1, RG = 300Ω
G = 2, RG = 150Ω
G = 5, RG = 60Ω
–6
–9
–12
–15
–18
–21
–24
–27
1M
10M
100M
FREQUENCY (Hz)
1G
10G
0
–3
G = 1, RG = 300Ω
G = 2, RG = 150Ω
G = 5, RG = 60Ω
–6
–9
–12
–15
–18
–21
–24
–27
1M
Figure 7. Small Signal Frequency Response
at Gain = 1, Gain = 2, and Gain = 5
1G
10G
6
VIN = 100mV
3
0
VIN = 2V p-p
0
VS = 3.3V
VS = 5.0V
–6
–9
–12
–15
–18
–6
–9
–12
–15
–18
–21
–21
–24
–24
1M
10M
100M
FREQUENCY (Hz)
1G
10G
–27
09209-008
–27
VS = 3.3V
VS = 5.0V
–3
1M
Figure 8. Small Signal Frequency Response
at VS = 3.3 V and VS = 5 V
10M
100M
FREQUENCY (Hz)
1G
10G
09209-011
CLOSED LOOP GAIN (dB)
–3
Figure 11. Large Signal Frequency Response
at VS = 3.3 V and VS = 5 V
6
3
VIN = 100mV
3
0
VIN = 2V p-p
0
–3
–6
CLOSED LOOP GAIN (dB)
TA = –40°C
TA = +25°C
TA = +105°C
–9
–12
–15
–18
–21
–3
–6
TA = –40°C
TA = +25°C
TA = +105°C
–9
–12
–15
–18
–21
–24
–27
–27
1M
10M
100M
FREQUENCY (Hz)
1G
10G
09209-009
–24
Figure 9. Small Signal Frequency Response
at TA = −40°C, TA = 25°C, and TA = 105°C
1M
10M
100M
FREQUENCY (Hz)
1G
Figure 12. Large Signal Frequency Response
at TA = −40°C, TA = 25°C, and TA = 105°C
Rev. C | Page 9 of 25
10G
09209-012
CLOSED LOOP GAIN (dB)
100M
FREQUENCY (Hz)
Figure 10. Large Signal Frequency Response
at Gain = 1, Gain = 2, and Gain = 5
3
CLOSED LOOP GAIN (dB)
10M
09209-010
NORMALIZED CLOSED LOOP GAIN (dB)
–3
09209-007
NORMALIZED CLOSED LOOP GAIN (dB)
VIN = 100mV
0
ADA4930-1/ADA4930-2
Data Sheet
3
6
VIN = 100mV p-p
0
CLOSED-LOOP GAIN (dB)
–3
RL = 1kΩ
RL = 200Ω
–6
–9
–12
–15
–18
–3
–9
–12
–15
–18
–21
–21
–24
–24
1M
10M
100M
FREQUENCY (Hz)
1G
–27
09209-013
–27
10G
RL = 1kΩ
RL = 200Ω
–6
1M
Figure 13. Small Signal Frequency Response for RL = 200 Ω and RL = 1 kΩ
100M
FREQUENCY (Hz)
1G
10G
Figure 16. Large Signal Frequency Response
for RL = 200 Ω and RL = 1 kΩ
0.4
3
VIN = 100mV
2
0.3
1
0.2
0
ADA4930-2,
ADA4930-2,
ADA4930-1,
ADA4930-1,
ADA4930-2,
ADA4930-2,
0.1
GAIN (dB)
GAIN (dB)
10M
09209-016
NORMALIZED CLOSED LOOP GAIN (dB)
VIN = 2V p-p
3
0
–1
–2
200Ω, OUT 1
200Ω, OUT 2
200Ω
1kΩ
1kΩ, OUT 1
1kΩ, OUT 2
0
–0.1
–3
–0.2
–4
10M
100M
1G
FREQUENCY (Hz)
–0.4
09209-014
–6
1M
1M
–50
–50
–60
GAIN = 1
GAIN = 1
GAIN = 2
GAIN = 2
GAIN = 5
GAIN = 5
DISTORTION (dBc)
HD2,
HD3,
HD2,
HD3,
HD2,
HD3,
–90
–70
HD2,
HD3,
HD2,
HD3,
–80
RL =
RL =
RL =
RL =
200Ω
200Ω
1kΩ
1kΩ
–90
–100
–100
–120
1M
10M
100M
FREQUENCY (Hz)
200M
–110
1M
10M
100M
FREQUENCY (Hz)
Figure 18. Harmonic Distortion vs. Frequency
for RL = 200 Ω and RL = 1 kΩ
Figure 15. Harmonic Distortion vs. Frequency
for Gain = 1, Gain = 2, and Gain = 5
Rev. C | Page 10 of 25
200M
09209-018
–110
09209-015
DISTORTION (dBc)
–80
1G
Figure 17. Small Signal 0.1 dB Flatness vs. Frequency for
RL = 200 Ω and RL = 1 kΩ
–40
–70
100M
FREQUENCY (Hz)
Figure 14. VOCM Small Signal Frequency Response
–60
10M
09209-017
–0.3
–5
Data Sheet
ADA4930-1/ADA4930-2
–20
–60
–65
–40
–75
–80
HD2,
HD3,
HD2,
HD3,
–85
–90
DISTORTON (dBc)
DISTORTION (dBc)
–70
VS = 3.3V
VS = 3.3V
VS = 5.0V
VS = 5.0V
–95
–100
–60
HD2,
HD3,
HD2,
HD3,
–80
3.3V
3.3V
5.0V
5.0V
–100
–120
100M
200M
FREQUENCY (Hz)
–140
1.0
2.0
2.5
3.0
3.5
3.0
VOUT (V p-p)
Figure 19. ADA4930-1 Harmonic Distortion vs. Frequency
at VS = 3.3 V and VS = 5 V
Figure 22. Harmonic Distortion vs. Output @ 10 MHz
–40
–40
10MHz,
10MHz,
70MHz,
70MHz,
–50
HD2
HD3
HD2
HD3
–50
DISTORTION (dBc)
–60
DISTORTION (dBc)
1.5
09209-022
10M
09209-019
–110
1M
09209-023
–105
–70
–80
–90
10MHz,
10MHz,
70MHz,
70MHz,
–60
–70
HD2
HD3
HD2
HD3
–80
–90
–100
–100
–110
0.5
0.6
0.8
0.7
0.9
1.0
1.1
1.2
VOCM ABOVE – VS (V)
–110
0.5
09209-020
2.0
2.5
Figure 23. Harmonic Distortion vs. VOCM
at 10 MHz and 70 MHz
0
20
VOUT = 1V p-p
VOUT = 1V p-p
VOUT = 2V p-p
VOUT = 2V p-p
NORMALIZED SPECTRUM (dBc)
HD2,
HD3,
HD2,
HD3,
–20
–40
–60
–80
–100
–120
0
–20
–40
–60
–80
–100
–120
10M
FREQUENCY (Hz)
100M
200M
09209-021
DISTOTION (dBc)
1.5
VOCM ABOVE – VS (V)
Figure 20. Harmonic Distortion vs. VOCM at VS = 3.3 V
at 10 MHz and 70 MHz
–140
1M
1.0
Figure 21. Distortion vs. VOUT at VS = 3.3 V
–140
69.8
69.9
70.0
70.1
FREQUENCY (MHz)
70.2
Figure 24. 70 MHz Intermodulation Distortion
Rev. C | Page 11 of 25
70.3
09209-024
–120
0.4
ADA4930-1/ADA4930-2
Data Sheet
–40
–20
–45
–30
–40
PSRR (dB)
CMRR (dB)
–50
–55
–60
–50
–60
–70
–65
–80
–70
1M
10M
FREQUENCY (Hz)
100M
1G
–100
100k
09209-025
–75
100k
1G
–20
CHANNEL 1 TO CHANNEL 2
CHANNEL 2 TO CHANNEL 1
VIN = 1V p-p
GAIN = 2
–25
–80
–30
CROSSTALK (dB)
–90
–100
–110
–120
–35
–40
–45
–50
–130
10M
1G
100M
FREQUENCY (Hz)
–60
09209-026
–140
1M
1M
10M
100M
FREQUENCY (Hz)
1G
09209-029
–55
Figure 29. Output Balance vs. Frequency, RL = 200 Ω
Figure 26. Crosstalk vs. Frequency, RL = 200 Ω
–50
0
–55
S11
S22
–10
–60
–65
DISTORTION (dBc)
–20
–30
–40
–50
–70
–75
–80
–85
RL = 200Ω
RL = 1kΩ
–90
–95
–60
–70
1M
10M
100M
FREQUENCY (Hz)
1G
10G
09209-027
–100
Figure 27. S11, S22, RL = 200 Ω
–105
1M
10M
FREQUENCY (Hz)
Figure 30. SFDR
Rev. C | Page 12 of 25
100M
200M
09209-030
CROSSTALK (dB)
100M
Figure 28. PSRR vs. Frequency, RL = 200 Ω
–60
S PARAMETERS (dB)
10M
FREQUENCY (Hz)
Figure 25. CMRR vs. Frequency, RL = 200 Ω
–70
1M
09209-028
–90
Data Sheet
ADA4930-1/ADA4930-2
80
60
70
30
60
0
30
–150
0
–180
–10
–210
–20
–240
–30
–270
100k
1M
10M
100M
0
–300
10G
1G
09209-031
–40
10k
1
FREQUENCY (MHz)
10
100
1k
10k
100k
1M
100M
09209-034
–120
10
18
20
09209-035
PHASE
20
10
18
20
09209-036
–90
VN (nV/√hz)
–60
30
PHASE (°)
GAIN
40
10M
FREQUENCY (Hz)
Figure 34. Voltage Noise Spectral Density
Figure 31. Open Loop Gain and Phase
1.00
0.10
0.98
0.96
0.05
VOUT (V)
VOUT (V)
0.94
0
0.92
0.90
0.88
0.86
–0.05
0.84
0.82
0
2
4
6
8
10
TIME (ns)
0.80
09209-032
–0.10
0
2
4
6
8
10
12
14
16
TIME (ns)
Figure 32. Small Signal Pulse Response
Figure 35. Small Signal VOCM Pulse Response
2.0
3.0
VO = 2V p-p
VO = 1V p-p
1.5
2.5
1.0
2.0
VOUT (V)
0.5
0
1.5
–0.5
1.0
–1.0
0.5
–1.5
–2.0
0
2
4
6
8
TIME (ns)
10
09209-033
VOUT (V)
GAIN (dB)
50
100
Figure 33. Large Signal Pulse Response
0
0
2
4
6
8
10
12
14
16
TIME (ns)
Figure 36. Large Signal VOCM Pulse Response
Rev. C | Page 13 of 25
Data Sheet
2.5
2.00
2.0
1.75
1.5
1.50
1.0
1.25
PD
+OUT
–OUT
1.00
0.75
0.5
0
–0.5
0.50
–1.0
0.25
–1.5
0
–2.0
–0.25
0
100
200
300
400 500 600
TIME (ns)
700
800
900
1000
VIN × 3
VO, dm
–2.5
0
5
10
15
20
25
30
TIME (ns)
35
Figure 38. Vo, dm Overdrive Recovery
Figure 37. PD Response vs. Time
Rev. C | Page 14 of 25
40
45
50
09209-038
VOLTAGE (V)
2.25
09209-037
VOLTAGE (V)
ADA4930-1/ADA4930-2
Data Sheet
ADA4930-1/ADA4930-2
TEST CIRCUITS
301Ω
+VS
50Ω
301Ω
57.6Ω
VIN
VOCM
0.9V
1kΩ
ADA4930
301Ω
0.9V
09209-046
26.7Ω
301Ω
0.9V
Figure 39. Equivalent Basic Test Circuit
301Ω
+VS
50Ω
301Ω
57.6Ω
VIN
50Ω
VOCM
0.9V
ADA4930
50Ω
301Ω
0.9V
09209-047
26.7Ω
301Ω
0.9V
Figure 40. Test Circuit for Output Balance
301Ω
+VS
VIN
0.1µF 412Ω
301Ω
FILTER
VOCM
57.6Ω
261Ω
ADA4930
0.1µF 412Ω
301Ω
0.9V
FILTER
0.9V
0.9V
26.7Ω
0.9V
301Ω
Figure 41. Test Circuit for Distortion Measurements
Rev. C | Page 15 of 25
09209-048
50Ω
ADA4930-1/ADA4930-2
Data Sheet
OPERATIONAL DESCRIPTION
Common-Mode Voltage
DEFINITION OF TERMS
Common-mode voltage refers to the average of two node voltages.
The output common-mode voltage is defined as
–FB
RG
+IN
VOCM
–OUT
ADA4930
–DIN
RG R
F
–IN
VOUT, cm = (V+OUT + V−OUT)/2
RL, dm VOUT, dm
+OUT
+FB
Balance
09209-049
+DIN
RF
Figure 42. Circuit Definitions
Differential Voltage
Differential voltage refers to the difference between two
node voltages. For example, the output differential voltage (or,
equivalently, output differential-mode voltage) is defined as
VOUT, dm = (V+OUT − V−OUT)
Output balance is a measure of how close the differential signals are
to being equal in amplitude and opposite in phase. Output balance
is most easily determined by placing a well-matched resistor
divider between the differential voltage nodes and comparing the
magnitude of the signal at the divider midpoint with the magnitude
of the differential signal (see Figure 39). By this definition, output
balance is the magnitude of the output common-mode voltage
divided by the magnitude of the output differential mode voltage.
where V+OUT and V−OUT refer to the voltages at the +OUT and
−OUT terminals with respect to a common reference.
Rev. C | Page 16 of 25
Output Balance Error =
VOUT , cm
VOUT , dm
Data Sheet
ADA4930-1/ADA4930-2
THEORY OF OPERATION
Two feedback loops control the differential and common-mode
output voltages. The differential feedback, set with external
resistors, controls the differential output voltage. The commonmode feedback controls the common-mode output voltage. This
architecture makes it easy to set the output common-mode level
to any arbitrary value within the specified limits. The output
common-mode voltage is forced to be equal to the voltage applied
to the VOCM input by the internal common-mode feedback loop.
The internal common-mode feedback loop produces outputs
that are highly balanced over a wide frequency range without
requiring tightly matched external components. This results
in differential outputs that are very close to the ideal of being
identical in amplitude and are exactly 180° apart in phase.
ESTIMATING THE OUTPUT NOISE VOLTAGE
The differential output noise of the ADA4930-1/ADA4930-2 can
be estimated using the noise model in Figure 43. The input-referred
noise voltage density, vnIN, is modeled as differential. The noise
currents, inIN− and inIN+, appear between each input and ground.
VnRG1
SETTING THE CLOSED-LOOP GAIN
+
inIN–
VIN , dm
=
VnIN
ADA4930
VnOD
VOCM
VnRG2
RG2
RF2
VnCM
VnRF2
Figure 43. Noise Model
Similar to the case of conventional op amps, the output noise
voltage densities can be estimated by multiplying the inputreferred terms at +IN and −IN by an appropriate output factor.
The output voltage due to vnIN is obtained by multiplying vnIN by
the noise gain, GN.
The circuit noise gain is
GN =
2
(β1 + β2 )
where the feedback factors are
β1 =
RG1
RG2
and β2 =
.
RF2 + RG2
RF1 + RG1
When the feedback factors are matched, RF1/RG1 = RF2/RG2,
1
R
β1 = β2 = β, and the noise gain becomes GN = = 1 + F .
β
RG
The noise currents are uncorrelated with the same mean-square
value, and each produces an output voltage that is equal to the
noise current multiplied by the associated feedback resistance.
The noise voltage density at the VOCM pin is vnCM. When the
feedback networks have the same feedback factor, as in most
cases, the output noise due to vnCM is common-mode and the
output noise from VOCM is zero.
The differential-mode gain of the circuit in Figure 42 is
determined by
VOUT , dm
VnRF1
RF1
inIN+
ANALYZING AN APPLICATION CIRCUIT
The ADA4930-1/ADA4930-2 use high open-loop gain and
negative feedback to force their differential and common-mode
output voltages to minimize the differential and common-mode
error voltages. The differential error voltage is defined as the
voltage between the differential inputs labeled +IN and −IN
(see Figure 42). For most purposes, this voltage can be assumed
to be zero. Similarly, the difference between the actual output
common-mode voltage and the voltage applied to VOCM can also
be assumed to be zero. Starting from these two assumptions,
any application circuit can be analyzed.
RG1
09209-050
The ADA4930-1/ADA4930-2 differ from conventional op amps
in that they have two outputs whose voltages move in opposite
directions and an additional input, VOCM. Like an op amp, they rely
on high open-loop gain and negative feedback to force these
outputs to the desired voltages. The ADA4930-1/ADA4930-2
behave much like standard voltage feedback op amps and facilitate
single-ended-to-differential conversions, common-mode level
shifting, and amplifications of differential signals. Like op amps,
the ADA4930-1/ADA4930-2 have high input impedance and low
output impedance.
RF
RG
where the gain and feedback resistors, RG and RF, on each side
are equal.
Each of the four resistors contributes (4kTRxx)1/2. The noise
from the feedback resistors appears directly at the output, and
the noise from the gain resistors appears at the output multiplied
by RF/RG.
The total differential output noise density, vnOD, is the root-sumsquare of the individual output noise terms.
vnOD =
Rev. C | Page 17 of 25
8
∑ (vnODi )2
i =1
ADA4930-1/ADA4930-2
Data Sheet
Table 11. Output Noise Voltage Density Calculations for Matched Feedback Networks
Input Noise Contribution
Differential Input
Inverting Input
Noninverting Input
VOCM Input
Gain Resistor RG1
Gain Resistor RG2
Feedback Resistor RF1
Feedback Resistor RF2
Input Noise Term
vnIN
inIN+
inIN−
vnCM
vnRG1
vnRG2
vnRF1
vnRF2
Input Noise
Voltage Density
vnIN
inIN+ × (RF2)
inIN− × (RF1)
vnCM
(4kTRG1)1/2
(4kTRG2)1/2
(4kTRF1)1/2
(4kTRF2)1/2
Output
Multiplication Factor
GN
1
1
0
RF1/RG1
RF2/RG2
1
1
Differential Output Noise
Voltage Density Terms
vnOD1 = GN(vnIN)
vnOD2 = (inIN+)(RF2)
vnOD3 = (inIN−)(RF1)
vnOD4 = 0
vnOD5 = (RF1/RG1)(4kTRG1)1/2
vnOD6 = (RF2/RG2)(4kTRG2)1/2
vnOD7 = (4kTRF1)1/2
vnOD8 = (4kTRF2)1/2
Table 12. Differential Input, DC-Coupled, VS = 5 V
Nominal Gain (dB)
0
6
10
14
RF1, RF2 (Ω)
301
301
301
301
RG1, RG2 (Ω)
301
150
95.3
60.4
RIN, dm (Ω)
602
300
190.6
120.4
Differential Output Noise Density (nV/√Hz)
4.9
6.2
7.8
10.1
Table 13. Single-Ended Ground-Referenced Input, DC-Coupled, RS = 50 Ω, VS = 5 V
Nominal Gain (dB)
0
6
10
14
1
RF1, RF2 (Ω)
301
301
301
301
RG1 (Ω)
142
63.4
33.2
10.2
RT (Ω)
64.2
84.5
1k
1.15 k
RIN, cm (Ω)
190.67
95.06
53.54
17.5
RG2 (Ω)1
170
95
69.3
57.7
Differential Output Noise Density (nV/√Hz)
5.9
7.8
9.3
10.4
RG2 = RG1 + (RS||RT).
Table 11 summarizes the input noise sources, the multiplication
factors, and the output-referred noise density terms.
Table 12 and Table 13 list several common gain settings, associated
resistor values, input impedance, and output noise density for both
balanced and unbalanced input configurations.
IMPACT OF MISMATCHES IN THE FEEDBACK
NETWORKS
As previously mentioned, even if the external feedback networks
(RF/RG) are mismatched, the internal common-mode feedback
loop still forces the outputs to remain balanced. The amplitudes
of the signals at each output remain equal and 180° out of phase.
The input-to-output differential mode gain varies proportionately
to the feedback mismatch, but the output balance is unaffected.
The gain from the VOCM pin to VO, dm is equal to
2(β1 − β2)/(β1 + β2)
When β1 = β2, this term goes to zero and there is no differential
output voltage due to the voltage on the VOCM input (including
noise). The extreme case occurs when one loop is open and the
other has 100% feedback; in this case, the gain from VOCM input
to VO, dm is either +2 or −2, depending on which loop is closed. The
feedback loops are nominally matched to within 1% in most
applications, and the output noise and offsets due to the VOCM
input are negligible.
If the loops are intentionally mismatched by a large amount, it is
necessary to include the gain term from VOCM to VO, dm and
account for the extra noise. For example, if β1 = 0.5 and β2 = 0.25,
the gain from VOCM to VO, dm is 0.67. If the VOCM pin is set to 0.9 V,
a differential offset voltage is present at the output of
(0.9 V)(0.67) = 0.6 V. The differential output noise contribution
is (5 nV/√Hz)(0.67) = 3.35 nV/√Hz. Both of these results are
undesirable in most applications; therefore, it is best to use
nominally matched feedback factors.
Mismatched feedback networks also result in a degradation of
the ability of the circuit to reject input common-mode signals,
much the same as for a four-resistor difference amplifier made
from a conventional op amp.
As a practical summarization of the previous issues, resistors of
1% tolerance produce a worst-case input CMRR of approximately
40 dB, a worst-case differential-mode output offset of 9 mV due
to a 0.9 V VOCM input, negligible VOCM noise contribution, and
no significant degradation in output balance error.
INPUT COMMON-MODE VOLTAGE RANGE
The input common-mode range at the summing nodes of the
ADA4930-1/ADA4930-2 is specified as 0.3 V to 1.5 V at VS = 3.3 V.
To avoid nonlinearities, the voltage swing at the +IN and −IN
terminals must be confined to these ranges.
Rev. C | Page 18 of 25
Data Sheet
ADA4930-1/ADA4930-2
Due to the wide bandwidth of the ADA4930-1/ADA4930-2, the
value of RG must be greater than or equal to 301 Ω at unity gain
to provide sufficient damping in the amplifier front end. In the
terminated case, RG includes the Thevenin resistance of the
source and load terminations.
SETTING THE OUTPUT COMMON-MODE VOLTAGE
The VOCM pin of the ADA4930-1/ADA4930-2 is biased at 3/10 of
the total supply voltage above −VS with an internal voltage divider.
The input impedance of the VOCM pin is 8.4 kΩ. When relying
on the internal bias, the output common-mode voltage is within
about 100 mV of the expected value.
For an unbalanced single-ended input signal, as shown in
Figure 45, the input impedance is
RIN,SE = RG1
where:
β1 =
β2 =
RF
ADA4930
+VS
RG
+IN
VOCM
–DIN
RG
VOUT, dm
–IN
RF
09209-051
+DIN
Figure 44. ADA4930-1/ADA4930-2 Configured for Balanced (Differential) Inputs
RG 2
RG2 + R F 2
+VS
RIN, SE
RG1
VOCM
ADA4930
RL
VOUT, dm
RG2
–VS
RF2
Figure 45. ADA4930-1/ADA4930-2 with Unbalanced (Single-Ended) Input
For a balanced system where RG1 = RG2 = RG and RF1 = RF2 = RF,
the equations simplify to




RG
R
G

β1 = β2 =
and R IN,SE = 


RF
R G + RF
 1−

 2(RG + R F ) 
CALCULATING THE INPUT IMPEDANCE FOR AN
APPLICATION CIRCUIT
The effective input impedance depends on whether the signal
source is single-ended or differential. For a balanced differential
input signal, as shown in Figure 44, the input impedance (RIN, dm)
between the inputs (+DIN and −DIN) is RIN, dm = 2 × RG.
RG1
RG1 + R F1
RF1
In cases where accurate control of the output common-mode
level is required, it is recommended that an external source or
resistor divider be used with source resistance less than 100 Ω.
The output common-mode offset listed in the Specifications
section assumes that the VOCM input is driven by a low
impedance voltage source.
It is also possible to connect the VOCM input to a common-mode
voltage (VCM) output of an ADC. However, care must be taken
to ensure that the output has sufficient drive capability. The
input impedance of the VOCM pin is approximately 10 kΩ. If
multiple ADA4930-1/ADA4930-2 devices share one reference
output, it is recommended that a buffer be used.
β1 + β2
β1( β2 + 1)
09209-052
MINIMUM RG VALUE
The input impedance of the circuit is effectively higher than it
would be for a conventional op amp connected as an inverter
because a fraction of the differential output voltage appears at
the inputs as a common-mode signal, partially bootstrapping
the voltage across the input resistor RG1. The common-mode
voltage at the amplifier input terminals can be easily determined
by noting that the voltage at the inverting input is equal to the
noninverting output voltage divided down by the voltage divider
formed by RF2 and RG2. This voltage is present at both input
terminals due to negative voltage feedback and is in phase with
the input signal, thus reducing the effective voltage across RG1,
partially bootstrapping it.
Terminating a Single-Ended Input
This section describes the five steps that properly terminate a
single-ended input to the ADA4930-1/ADA4930-2. Assume a
system gain of 1, RF1 = RF2 = 301 Ω, an input source with an opencircuit output voltage of 2 V p-p, and a source resistance of 50 Ω.
Figure 46 shows this circuit.
1.
Calculate the input impedance.
β1 = β2 = 301/602 = 0.5 and RIN = 401.333 Ω
Rev. C | Page 19 of 25
ADA4930-1/ADA4930-2
Data Sheet
RF1
Decrease RG2 to RG2 =
+VS
RG1
50Ω
301Ω
VOCM
gain and decrease RG1 to (RG2 − RTH) to maintain
balanced gain resistances.
ADA4930
The first compensation method is used in the Analog Devices
DiffAmpCalc™ tool. Using the second compensation method,
RG2 = 160.498 Ω and RG1 = 160.498 − 26.66 = 133.837 Ω. The
modified circuit is shown in Figure 49.
RL VOUT, dm
RG2
301Ω
09209-053
–VS
RF2
301Ω
RF1
301Ω
+VS
Figure 46. Single-Ended Input Impedance RIN
2.
Add a termination resistor, RT. To match the 50 Ω source
resistance, RT is added. Because RT||401.33 Ω = 50 Ω,
RT = 57.116 Ω.
VTH
1.066V p-p
RTH
RG1
26.661Ω
133.837Ω
VOCM
RF1
+VS
RS
VS
2V p-p
–VS
RF2
RG1
50Ω
RT
57.116Ω
301Ω
301Ω
VOCM
ADA4930
Figure 49. Thevenin Equivalent with Matched Gain Resistors
RL VOUT, dm
Figure 49 presents an easily manageable circuit with matched
feedback loops that can be easily evaluated.
The modified gain resistor, RG1, changes the input impedance.
Repeat Step 1 through Step 4 several times using the modified
value of RG1 from the previous iteration until the value of
RT does not change from the previous iteration. After three
additional iterations, the change in RG1 is less than 0.1%.
The final circuit is shown in Figure 50 with the closest
0.5% resistor values.
RG2
301Ω
5.
09209-054
–VS
RF2
301Ω
Figure 47. Adding Termination Resistor RT
3.
Replace the source-termination resistor combination with
its Thevenin equivalent. The Thevenin equivalent of the
source resistance RS and the termination resistance RT is
RTH = RS||RT = 26.66 Ω. The Thevenin equivalent of the
source voltage is
RS
RS
VS
2V p-p
RTH
RT
57.116Ω
VTH
1.066V p-p
26.661Ω
VP
142Ω
VOCM
ADA4930
RL
VOUT, dm
1.990V p-p
VN
–VS
RF2
Set RF1 = RF2 = RF to maintain a balanced system.
Compensate the imbalance caused by RTH. There are two
methods available to compensate, which follow:
•
RG
RT
64.2Ω
RG2
Figure 48. Thevenin Equivalent Circuit
4.
50Ω
169Ω
09209-055
50Ω
RF1
301Ω
+VS
0.998V p-p
RT
= 1.066 V p-p
VTH = VS
RS + RT
VS
2V p-p
RL VOUT, dm
160.498Ω
301Ω
RIN
50Ω
ADA4930
RG2
09209-056
RS
R F × VTH
to maintain system
VS × Gain
301Ω
Figure 50. Terminated Single-Ended-to-Differential System with G = 1
Add RTH to RG2 to maintain balanced gain resistances
V
and increase RF1 and RF2 to RF = S Gain(RG + RTH) to
VTH
maintain the system gain.
Rev. C | Page 20 of 25
09209-057
VS
2V p-p
•
301Ω
RIN
401.333Ω
Data Sheet
ADA4930-1/ADA4930-2
Terminating a Single-Ended Input in a Single-Supply
Applications
3.
When the application circuit of Figure 50 is powered by a single
supply, the common-mode voltage at the amplifier inputs, VP
and VN, may have to be raised to comply with the specified input
common-mode range. Two methods are available: a dc bias on
the source, as shown in Figure 51, or by connecting resistors
RCM between each input and the supply, as shown on Figure 54.
To comply with the minimum specified input common-mode
voltage of 0.3 V at VS = 3.3 V, set the minimum value of VP
and VN to 0.3 V.
Recognize that VP and VN are at their minimum values when
VOP and VS are at their minimum (and therefore VON is at its
maximum).
4.
Let
VP min = VN min = 0.3 V, VOCM = VCM = 1 V, VTH min = −VTH/2
VON max = VOCM + VOUT, dm/4 and VOP min = VOCM − VOUT, dm/4
Input Common-Mode Adjustment with DC Biased Source
To drive a 1.8 V ADC with VCM = 1 V, a 3.3 V single supply
minimizes the power dissipation of the ADA4930-1/ADA4930-2.
The application circuit of Figure 50 on a 3.3 V single supply with a
dc bias added to the source is shown in Figure 51.
Substitute conditions into the nodal equation for VP and solve
for VDC-TH.
0.3 = −1.124/2 + VDC-TH + 0.361 × (1 + 1.99/4 + 1.124/2 – VDC-TH)
RF1
0.3 + 0.562 − 0.361 − 0.18 − 0.203 = 0.639 VDC-TH
301Ω
VDC-TH = 0.186 V
3.3V
RS
VOCM
RG2
50Ω
64.2Ω
Or
Substitute conditions into the nodal equation for VN and
solve for VDC-TH.
142Ω
ADA4930
RL VOUT, dm
1.990V p-p
VN
0.3 = VDC-TH + 0.361 × (1 − 1.99/4 − VDC-TH)
142Ω
0.3 – 0.361 + 0.18 = 0.639 × VDC-TH
RF2
VDC
301Ω
VDC-TH = 0.186 V
5.
Converting VDC-TH from its Thevenin equivalent results in
Figure 51. Single-Supply, Terminated Single-Ended-to-Differential System
with G = 1
V DC =
To determine the minimum required dc bias, the following steps
must be taken:
1.
R S + RTH
× 0.186 = 0.33 V
RTH
The final application circuit is shown in Figure 53. The
additional dc bias of 0.33 V at the inputs ensures that the
minimum input common-mode requirements are met when
the source signal is bipolar with a 2 V p-p amplitude and
VOCM is at 1 V.
Convert the terminated inputs to their Thevenin equivalents,
as shown in the Figure 52 circuit.
RF1
301Ω
RF1
3.3V
RTH
RG1
28.11Ω
142Ω
VP
RTH
RG2
28.11Ω
142Ω
VON
3.3V
VOCM
VTH
1.124V p-p
301Ω
ADA4930
RS
RL VOUT, dm
1.99V p-p
VN
VS
2V p-p
VOP
50Ω
RG1
RT
64.2Ω
142Ω
VOCM
RF2
301Ω
09209-159
RG2
VDC-TH
VDC
0.33V
Figure 52. Thevenin Equivalent of Single-Supply Application Circuit
2.
Write a nodal equation for VP or VN.
VP = VTH + VDC −TH +
VN = VDC −TH +
50Ω
142 + 28.11
(VON − VTH − VDC −TH )
301 + 142 + 28.11
142 + 28.11
(VOP − VDC −TH )
301 + 142 + 28.11
Recognize that while the ADA4930-1/ADA4930-2 is in its
linear operating region, VP and VN are equal. Therefore,
both equations in Step 2 give equal results.
Rev. C | Page 21 of 25
64.2Ω
VP
ADA4930
VN
RL VOUT, dm
1.990V p-p
142Ω
RF2
301Ω
Figure 53. Single-Supply Application Circuit with DC Source Bias
09209-160
VS
2V p-p
RT
64.2Ω
VP
09209-151
50Ω
RG1
ADA4930-1/ADA4930-2
Data Sheet
Input Common-Mode Adjustment with Resistors
Calculate the following:
The circuit shown in Figure 54 shows an alternate method to
bias the amplifier inputs, eliminating the dc source.
1.
2.
3.
4.
3.3V
RCM
VS
β1 and β2. For the circuit shown in Figure 54, β1 = 0.5 and
β2 = 0.5.
RCM for VP min = 0.3 V and VIN min = −0.5 V. RCM = 9933 Ω.
The new values for β1 and β2. β1 = 0.4925 and β2 = 0.4925.
The input impedance using the following:
RF1
301Ω
+VS
VSOURCE
2V p-p
50Ω
RT
RG1
301Ω
VOCM
ADA4930
RIN − SE
RL VOUT, dm
RG2
301Ω
RF2
301Ω
09209-152
RCM
VS
3.3V
Figure 54. Single-Supply Biasing Scheme with Resistors
Define β1 = RP/RF1 and β2 = RN/RF2, where RP = RG1||RCM||RF1
and RN = RG2||RCM||RF2.
6.
7.
8.
9.
Set RF1 = RF2 = RF to maintain a balanced system, as shown.
Write a nodal equation at VP and solve for VP.
VP =
β1β2  RF
2R

VIN + 2VOCM + VS F
β1 + β2  RG1
RCM
+VS




RS
VS
2V p-p
50Ω
RF1
301Ω
RG1
RT
65.1Ω
142Ω
VOCM
ADA4930
RL VOUT, dm
RG2
Determine the minimum input voltage, VIN min at the output of
the source. Recognize that once properly terminated, the source
voltage is ½ of its open circuit value. Therefore, VIN min = −0.5 V.
170Ω
–VS
Rearrange the VP equation for RCM
 β1 + β2

RF


 β1β2 VP min − R VIN min − 2VOCM 
G1


RCM
1.87kΩ
+VS
Determine VP min. This is the minimum input common-mode
voltage from the Specifications section. For a 3.3 V supply, VP min
= 0.3 V.
1
1
=
RCM 2VS RF






β1
β2
+

=R 
G1
 β1 + β2 − RF1 β1β2 




RG1



RIN-SE = 399.35 Ω.
RT, RTH, and VTH. RT = 57.16 Ω, RTH = 26.67 Ω, and
VTH = 1.067 V.
The new values for RG1 and RG2. RG2 = 160.55 Ω and
RG1 = 133.88 Ω.
The new values for β1 and β2. β1 = 0.284 and β2 = 0.317.
The new value of RCM. RCM = 4759.63 Ω.
Repeat Step 3 through Step 8 until the values of RG1 and RG2
remain constant between iterations. After four iterations,
the final circuit is shown in Figure 55.
5.
–VS


1
= RG1 
 1 − VP
 V
INP

+VS
RCM
RF2
1.87kΩ
301Ω
09209-153
VIN
RS
Figure 55. Single-Supply, Single-Ended Input System with Bias Resistors
Rev. C | Page 22 of 25
Data Sheet
ADA4930-1/ADA4930-2
LAYOUT, GROUNDING, AND BYPASSING
The ADA4930-1/ADA4930-2 are high speed devices. Realizing
their superior performance requires attention to the details of
high speed PCB design.
Use radio frequency transmission lines to connect the driver
and receiver to the amplifier.
Minimize stray capacitance at the input/output pins by clearing
the underlying ground and low impedance planes near these pins
(see Figure 56).
The first requirement is to use a multilayer PCB with solid ground
and power planes that cover as much of the board area as possible.
Bypass each power supply pin directly to a nearby ground plane, as
close to the device as possible. Use 0.1 µF high frequency ceramic
chip capacitors.
If the driver/receiver is more than one-eighth of the wavelength
from the amplifier, the signal trace widths should be minimal.
This nontransmission line configuration requires the underlying
and adjacent ground and low impedance planes to be cleared
near the signal lines.
Provide low frequency bulk bypassing, using 10 µF tantalum
capacitors from each supply to ground.
The exposed thermal paddle is internally connected to the ground
pin of the amplifier. Solder the paddle to the low impedance
ground plane on the PCB to ensure the specified electrical
performance and to provide thermal relief. To reduce thermal
impedance further, it is recommended that the ground planes
on all layers under the paddle be connected together with vias.
Stray transmission line capacitance in combination with package
parasitics can potentially form a resonant circuit at high
frequencies, resulting in excessive gain peaking or possible
oscillation.
Signal routing should be short and direct to avoid such parasitic
effects. Provide symmetrical layout for complementary signals
to maximize balanced performance.
1.30
0.80
09209-058
09209-059
1.30 0.80
Figure 57. Recommended PCB Thermal Attach Pad Dimensions (Millimeters)
Figure 56. ADA4930-1 Ground and Power Plane Voiding
in the Vicinity of RF and RG
1.3 mm
0.8 mm
TOP METAL
GROUND PLANE
09209-060
POWER PLANE
BOTTOM METAL
Figure 58. Cross-Section of 4-Layer PCB Showing Thermal Via Connection to Buried Ground Plane (Dimensions in Millimeters)
Rev. C | Page 23 of 25
ADA4930-1/ADA4930-2
Data Sheet
HIGH PERFORMANCE ADC DRIVING
A third-order, 40 MHz, low-pass filter between the ADA4930-1
and the AD9255 reduces the noise bandwidth of the amplifier
and isolates the driver outputs from the ADC inputs.
The ADA4930-1/ADA4930-2 provide excellent performance in
3.3 V single-supply applications.
The circuit shown in Figure 59 is an example of the ADA4930-1
driving an AD9255, 14-bit, 80 MSPS ADC that is specified to
operate with a single 1.8 V supply. The performance of the ADC
is optimized when it is driven differentially, making the best use of
the signal swing available within the 1.8 V supply. The ADA4930-1
performs the single-ended-to-differential conversion, commonmode level shifting, and buffering of the driving signal.
The circuit shown in Figure 60 is an example of ½ of an
ADA4930-2 driving ½ of an AD9640, a 14-bit, 80 MSPS
ADC that is specified to operate with a single 1.8 V supply.
The performance of the ADC is optimized when it is driven
differentially, making the best use of the signal swing available
within the 1.8 V supply. The ADA4930-2 performs the singleended-to-differential conversion, common-mode level shifting,
and buffering of the driving signal.
The ADA4930-1 is configured for a single-ended input to
differential output with a gain of 2 V/V. The 84.5 Ω termination
resistor, in parallel with the single-ended input impedance of
95.1 Ω, provides a 50 Ω termination for the source. The additional
31.6 Ω (95 Ω total) at the inverting input balances the parallel
impedance of the 50 Ω source and the termination resistor that
drives the noninverting input.
The ADA4930-2 is configured for a single-ended input to
differential output with a gain of 2 V/V. The 88.5 Ω termination
resistor, in parallel with the single-ended input impedance of
114.75 Ω, provides a 50 Ω termination for the source. The
increased gain resistance at the inverting input balances the 50 Ω
source resistance and the termination resistor that drives the
noninverting input.
The VOCM pin is connected to the VCM output of the AD9255 and
sets the output common mode of the ADA4930-1 at 0.9 V.
The VOCM pin is connected to the CML output of the AD9640 and
sets the output common mode of the ADA4930-2 at 1 V.
Note that a dc bias must be added to the signal source and its
Thevenin equivalent to the gain resistor on the inverting side
to ensure that the inputs of the ADA4930-1 are kept at or above
the specified minimum input common-mode voltage at all times.
The 739 Ω resistors between each input and the 3.3 V supply
provide the necessary dc bias to guarantee compliance with the
input common-mode range of the ADA4930-2.
The 0.5 V dc bias at the signal source and the 0.314 V dc bias on
the gain resistor at the inverting input set the inputs of the
ADA4930-1 to ~0.48 V dc. With 1 V p-p maximum signal swing
at the input, the ADA4930-1 inputs swing between 0.36 V and
0.6 V.
For a common-mode voltage of 1 V, each ADA4930-2 output
swings between 0.501 V and 1.498 V, providing a 1.994 V p-p
differential output.
A third-order, 40 MHz, low-pass filter between the ADA4930-2
and the AD9640 reduces the noise bandwidth of the amplifier
and isolates the driver outputs from the ADC inputs.
For a common-mode voltage of 0.9 V, each ADA4930-1 output
swings between 0.401 V and 1.398 V, providing a 1.994 V p-p
differential output.
301Ω
1.8V
3.3V
63.4Ω
50Ω
VIN
1V p-p
84.5Ω
0.5V
VOCM
33Ω
+
ADA4930-1
30pF
168nH
AVDD
VIN–
DRVDD
AD9255
90pF
VIN+
33Ω
95Ω
AGND
168nH
D11 TO
D0
VCM
09209-157
0.314V
301Ω
Figure 59. Driving an AD9255, 14-Bit, 80 MSPS ADC
3.3V
301Ω
1.8V
3.3V
50Ω
88.5Ω
VIN
1V p-p
739Ω
33Ω
+
64.2Ω
VOCM
ADA4930-2
168nH
30pF
DRVDD
AD9640
90pF
96.2Ω
VIN+
33Ω
739Ω
3.3V
AVDD
VIN–
301Ω
168nH
VOCM
Figure 60. Driving an AD9640, 14-Bit, 80 MSPS ADC
Rev. C | Page 24 of 25
AGND
CML
D11 TO
D0
ADA4930-1/ADA4930-2
Data Sheet
OUTLINE DIMENSIONS
3.10
3.00 SQ
2.90
PIN 1
INDICATOR
0.32
0.25
0.20
13
0.50
BSC
PIN 1
INDICATOR
(0.30)
16
1
12
EXPOSED
PAD
1.80
1.70 SQ
1.60
9
TOP VIEW
0.80
0.75
0.70
4
5
8
0.50
0.40
0.30
0.20 MIN
BOTTOM VIEW
PKG-004326
SEATING
PLANE
10-09-2013-A
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
COMPLIANT TO JEDEC STANDARDS MO-220-WEED-2.
Figure 61. 16-Lead Lead Frame Chip Scale Package [LFCSP]
3 mm × 3 mm Body and 0.75 mm Package Height
(CP-16-35)
Dimensions shown in millimeters
4.10
4.00 SQ
3.90
PIN 1
INDICATOR
0.50
BSC
24
19
18
PIN 1
INDICATOR
1
2.40
2.30 SQ
2.20
EXPOSED
PAD
6
13
0.80
0.75
0.70
SEATING
PLANE
0.50
0.40
0.30
12
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.203 REF
0.30
0.25
0.20
7
BOTTOM VIEW
0.20 MIN
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-WGGD-8.
01-18-2012-A
TOP VIEW
Figure 62. 24-Lead Lead Frame Chip Scale Package [LFCSP]
4 mm × 4 mm Body and 0.75 mm Package Height
(CP-24-14)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
ADA4930-1YCPZ-R2
ADA4930-1YCPZ-RL
ADA4930-1YCPZ-R7
ADA4930-2YCPZ-R2
ADA4930-2YCPZ-RL
ADA4930-2YCPZ-R7
1
Temperature Range
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
−40°C to +105°C
Package Description
16-Lead LFCSP
16-Lead LFCSP
16-Lead LFCSP
24-Lead LFCSP
24-Lead LFCSP
24-Lead LFCSP
Z = RoHS Compliant Part.
©2010–2017 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D09209-0-5/17(C)
Rev. C | Page 25 of 25
Package Option
CP-16-35
CP-16-35
CP-16-35
CP-24-14
CP-24-14
CP-24-14
Ordering Quantity
250
5,000
1,500
250
5,000
1,500
Branding
H1G
H1G
H1G
Similar pages