General-purpose Operational Amplifiers /Comparators TROPHY SERIES Comparators LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR ●Description The Universal Standard family LM393 / LM339/ LM2903 / LM2901 monolithic ICs integrate two/four independent comparators on a single chip and feature high gain, low power consumption, and an operating voltage range from 2[V] to 36[V] (single power supply). No.11094EBT03 TROPHY SERIES Dual LM393 family LM393DR LM393PWR LM393DGKR Quad LM2903 family LM2901 family LM339 family LM2903DR LM2903PWR LM2903DGKR LM2903VQDR LM2903VQPWR LM2901DR LM2901PWR LM2901VQDR LM2901VQPWR LM339DR LM339PWR ●Features 1) Operating temperature range Commercial Grade LM339/393 family : 0[℃] to + 70[℃] Extended Industrial Grade LM2903/2901 family : -40[℃] to +125[℃] 2) Open collector output 3) Single / dual power supply compatible 4) Low supply current 0.8[mA] typ. (LM393/339/2903/2901 family) 5) Low input-bias current: 25[nA] typ. 6) Low input-offset voltage: 2[mV] typ. 7) Differential input voltage range equal to maximum rating 8) Low output saturation voltage 9) TTL,MOS,CMOS compatible output ●Pin Assignment 1OUT 1IN- 1 2 1IN+ 3 GN D 4 SOIC8 LM393DR LM2903DR LM2903VQDR 8 － 7 ＋ ＋ － TSSOP8 LM393PW R LM2903PW R LM2903VQPW R www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 1OUT 1 14 OUT3 2OUT 2 13 OUT4 Vcc 3 12 GND Vcc 2OUT 6 2IN- 5 2IN+ － 11 4IN+ 2IN+ 5 10 4IN- 1IN- 6 9 3IN+ 8 3IN- 7 SOIC14 LM339DR LM2901DR LM2901VQDR 1/17 ＋ 4 1IN+ LM393DGKR LM2903DGKR － 2IN- － MSOP8/VSSOP8 ＋ ＋ － ＋ TSSOP14 LM339PW R LM2901PW R LM2901VQPW R 2011.06 - Rev.B LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR Technical Note ●Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Supply Voltage Ratings LM393 family LM339 family LM2903 family LM2901 family Unit Vcc-GND +36 V Vid ±36 V Input Differential Voltage Common-mode Input Vicm Operating Temperature Topr Storage Temperature Range Tstg -65 to +150 ℃ Tj +150 ℃ Maximum Junction Temperature -0.3 to +36 0 to +70 V -40 to +125 ℃ ●Electric Characteristics ○LM393/339 family(Unless otherwise specified, Vcc=+5[V]) Limits Parameter Temperature Symbol range 25℃ Input Offset Voltage (*1) Input Offset Current (*1) Input Bias Current (*1) Unit LM339 family Min. Typ. Max. Min. Typ. Max. － 2 7 － 2 7 VIO Large Signal Differential Voltage Amplification AVD High Level Output Current IOH Low Level Output Voltage VOL Low Level Output Current IOL Supply Current ICC mV Vcc=5 to 30[V],VO=1.4[V] VIC=VIC(min) 88 nA VO=1.4[V] 88 nA VO=1.4[V] 88 － 9 － － 9 25℃ － 5 50 － 5 50 Full range － － 250 － － 150 25℃ － 25 250 － 25 250 Full range － － 400 － － 400 25℃ － － Vcc-1.5 － － Vcc-1.5 Full range － － Vcc-2.0 － － Vcc-2.0 25℃ 25 200 － 25 200 － V/mA 25℃ － 0.1 － － 0.1 － nA VID=1[V],VO=5[V] Full range － － 1 － － 1 μA VID=1[V],VO=30[V] 25℃ － 150 400 － 150 400 mV VID=-1[V],IOL=4[mA] 89 Full range － － 700 － － 700 25℃ 6 － － 6 16 － mA VID=-1[V],VOL=1.5[V] 89 25℃ － 0.8 1 － 0.8 2 V 88 － Vcc=15[V] VO=1.4 to 11.4[V], RL≧15[kΩ],VRL=15[V] 88 89 RL=∞,Vcc=5V mA Full range Tre Fig. No. － IIB VICR condition Full range IIO Common-mode Input Voltage Range Response Time LM393 family － － 2.5 － － － － 1.3 － － 1.3 － － 0.3 － － 0.3 － μs 25℃ 89 RL=∞,Vcc=30[V] RL=5.1[kΩ],VRL=5[V],CL=15pF VIN=100[mVp-p], overdrive=5[mV] RL=5.1[kΩ],VRL=5[V], CL=15pF VIN=TTL-Level input step Vref=1.4[V] 89 (*1) Absolute value www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 2/17 2011.06 - Rev.B LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR Technical Note ○LM2903/2901 family(Unless otherwise specified, Vcc=+5[V]) Limits Parameter Symbol Temperature range 25℃ Input Offset Voltage (*2) Input Offset Current (*2) Input Bias Current (*2) Min. Typ. Max. － 2 7 － 2 7 15 － － 15 25℃ － 5 50 － 5 50 Full range － － 200 － － 200 25℃ － 25 250 － 25 250 Full range － － 500 － － 500 25℃ － － Vcc-1.5 － － Vcc-1.5 Full range － － Vcc-2.0 － － Vcc-2.0 25℃ 25 100 － 25 100 25℃ － 0.1 － － Full range － － 1 25℃ － 150 25℃ － Full range IOL 25℃ ICC 25℃ IIO IIB High Level Output Current IOH LM2901(*3) Response Time Max. － AVD Supply Current Typ. － Large Signal Differential Voltage Amplification Low Level Output Current Min. Full range VICR LM2901V(*3) Unit LM2901 family VIO Common-mode Input Voltage Range Low Level Output Voltage LM2903 family VOL Tre Condition Fig. No mV Vcc=5 to MAX),VO=1.4[V] VIC=VIC (min) 88 nA VO=1.4[V] 88 nA VO=1.4[V] 88 V － 88 － V/mV Vcc=15[V],VOUT=1.4 to 11.4[V], RL≧15[kΩ],VRL=15[V] 88 0.1 － nA VID=1[V], VOH=5[V] － － 1 μA VID=1[V], VOH=MAX 400 － 150 500 150 400 － 150 400 mV VIN(-)=1[V],VIN(+)=0[V] ISINK≦4[mA] 89 － － 700 － － 700 6 16 － 6 16 － mA VID=-1[V], VOL=1.5[V] 89 － 0.8 2 － 0.8 2 89 RL=∞,Vcc=5V mA － 1 2.5 － 1 2.5 － 1.3 － － 1.3 － － 0.3 － － 0.3 － 25℃ 89 RL=∞,Vcc=MAX(*7) μs RL=5.1[Ω],VRL=5[V],CL=15pF VIN=100[mVp-p], Overdrive=5[mV] RL=5.1[kΩ],VRL=5[V], CL=15pF VIN=TTL-Level input step Vref=1.4[V] 89 (*2) Absolute value (*3) Supply Voltage Maximum Value LM2901DR, LM2901PWR MAX=30[V], LM2901VQDR, LM2901VQPWR MAX=32[V] www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 3/17 2011.06 - Rev.B LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR Technical Note ●Reference Data LM393 family LM393 family LM393 family 1 0℃ 800 LM393PWR 400 LM393DR 200 0 0 25 0.6 0.4 70℃ 0.2 75 100 125 10 20 30 SUPPLY VOLTAGE [V] Fig.1 LM393 family OUTPUT SATU RATION VOLT AGE [mV] OUTPUT SATURATION VOLTAGE [mV] 25℃ 200 0℃ 0 10 20 30 SUPPLY VOLTAGE [V] 300 5V 200 36V 100 2V 10 20 30 40 50 60 70 AMBIENT TEMPERATURE [℃] 20 30 40 50 60 70 AMBIEN T TEMPERATURE [℃] 0.4 0℃ 0.2 0 2 6 4 0℃ 2 25℃ 0 -2 70℃ -4 -6 LM393 family 6 4 2V 2 -2 36V -4 -6 20 30 40 0 . 40 70℃ SUPPLY VOLTAGE [V] Fig. 10 Input Bias Current – Supply Voltage 40 50 60 70 80 Fig. 9 LM393 family 50 40 120 36V 100 80 5V 60 40 2V 30 20 0℃ 10 0 25℃ -10 70℃ -20 -30 -40 0 40 30 Input Offset Voltage – Ambient Temperature LM393 family 160 20 0 20 AMBIENT TEMPERATURE [℃] INPUT OFFSET CURRENT [nA] 60 10 Fig. 8 INPUT BIAS CURRENT [nA] 80 5V 0 -8 10 140 25℃ 10 12 14 16 18 20 (VCC=5[V]) Input Offset Voltage – Supply Voltage 140 120 8 Fig. 6 SUPPLY VOLTAGE [V] LM393 family 30 4 Low Level Output Voltage – Output Sink Current (VOUT=1.5[V]) 20 0.6 8 0 Fig. 7 10 0.8 OUTPUT SINK CURRENT [mA] 6 80 Output Sink Current – Ambient Temperature 0 1.0 80 -8 20 70℃ LM393 family 8 0 0℃ 25℃ 1.2 (IOL=4[mA]) 20 100 1.4 Fig. 5 5V 160 1.6 0.0 0 INPUT OFFSET VOLTAGE [mV] 36V 80 LM393 family Output Saturation Voltage – Ambient Temperature 30 10 20 30 40 50 60 70 AMBIENT TEMPER ATURE [℃] 1.8 0 40 LM393 family 0 10 2.0 2V (IOL=4[mA]) 40 INPUT BIAS CURRENT [nA] 0 Supply Current – Ambient Temperature 400 Fig.4 OUTPUT SINK CURR ENT [mA] 40 LM393 family Output Saturation Voltage – Supply Voltage 10 5V Fig. 3 500 70℃ 0 2V 0.2 Fig.2 500 100 0.4 Supply Current – Supply Voltage Derating Curve 300 0.6 0 0 AMBIENT TEMPERATURE [℃] . 400 36V 0 70 50 25℃ LOW LEVEL OUTPUT VOLTAGE [V] 600 0.8 SUPPLY CURRENT [mA] SUPPLY CURRENT [mA] 0.8 LM393DGKR LM393 family 1 INPUT OFFSET VOLTAGE [mV] POWER DISSIPATION [mW] . . 1000 -50 0 10 20 30 40 50 60 70 AMBIENT TEMPERATURE [℃] 80 0 10 20 30 SUPPLY VOLTAGE [V] 40 Fig. 11 Fig. 12 Input Bias Current – Ambient Temperature Input Offset Current – Supply Voltage (*)The data above is ability value of sample, it is not guaranteed. LM393family:0[℃]~+70[℃] www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 4/17 2011.06 - Rev.B LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR Technical Note 20 10 5V 0 -10 2V -20 -30 -40 -50 . 130 LM393 family 25℃ 120 110 100 70℃ 80 70 20 30 40 50 60 70 AMBIENT TEMPERATURE [℃] 80 0 10 20 30 SUPPLY VOLTAGE [V] Fig. 13 POWER SUPPLY REJECTION RAT IO [dB] COMMON MODE REJECTION RATIO[dB] . 0℃ 25℃ 100 80 70℃ 60 40 0 10 20 30 SUPPLY VOLTAGE [V] 130 120 36V 110 5V 100 90 80 2V 70 60 40 0 10 80 Fig. 17 2V 90 5mV overdrive 2 20mV overdrive 1 100mV overdrive 80 70 60 10 20 30 40 50 60 70 AMBIENT TEMPERATURE [°C] 80 Large Signal Voltage Gain – Ambient Temperature LM393 family 140 130 120 110 100 90 80 70 60 0 10 20 30 40 50 60 70 AMBIENT TEMPERAT URE [°C] 80 Fig. 18 Power Supply Rejection Ratio – Ambient Temperature . 4 3 5mV overdrive 2 20mV overdrive 100mV overdrive 1 0 0 20 30 40 50 60 70 AMBIENT TEMPERATURE [°C] 5V LM393 family 5 RESPONSE TIME (HIGH to LOW) [μ ｓ] 4 10 20 30 40 50 60 70 AMBIENT TEMPERATURE [°C] Common Mode Rejection Ratio – Ambient Temperature LM393 family 0 100 0 LM393 family Fig. 16 3 110 Fig. 15 140 Common Mode Rejection Ratio – Supply Voltage 5 36V 120 Fig. 14 140 120 130 40 Large Signal Voltage Gain – Supply Voltage LM393 family 160 LM393 family 140 . 10 Input Offset Current – Ambient Temperature . . 0℃ 90 60 0 RESPONSE T IME (LOW to HIGH) [μs] LARGE SIGNAL VOLT AGE GAIN [dB] 36V 30 140 POWER SUPPLY REJECTION RATIO [dB] IN PUT OFFSET CU RRENT [nA] 40 . LM393 family 50 LARGE SIGNAL VOLTAGE GAIN [dB] ●Reference Data LM393 family 80 Fig. 19 Response Time (Low to High) – Ambient Temperature (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) 0 10 20 30 40 50 60 70 AMBIENT TEMPERATURE [°C] 80 Fig. 20 Response Time (High to Low) –Ambient Temperature (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) (*)The data above is ability value of sample, it is not guaranteed. LM393family:0[℃]~+70[℃] www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 5/17 2011.06 - Rev.B LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR Technical Note ●Reference Data LM339 family LM339 family LM339 family 1 0℃ 0.8 600 400 LM339DR 200 0 25 70 50 75 25℃ 0.6 0.4 70℃ 0.2 0 100 125 10 20 30 SUPPLY VOLTAGE [V] AMBIENT TEMPERATURE [℃] . Fig.21 Fig.22 Supply Current – Supply Voltage LM339 family 200 0℃ 100 0 0 10 20 30 SUPPLY VOLTAGE [V] LM339 family 300 5V 36V 100 0 10 Fig.24 20 30 40 50 60 70 AMBIENT TEMPERATURE [℃] 5V 2V 0 20 30 40 50 60 70 AMBIEN T TEMPERATURE [℃] 0.8 0.6 0.4 0℃ 0.2 0 2 6 8 10 12 14 16 18 20 Fig. 26 Low Level Output Voltage – Output Sink Current (VCC=5[V]) LM339 family 8 6 4 0℃ 2 25℃ 0 -2 70℃ -4 -6 6 4 2V 2 5V 0 -2 36V -4 -6 -8 0 80 4 OUTPUT SINK CURRENT [mA] 10 20 30 40 0 10 20 30 40 50 60 70 80 AMBIENT TEMPERATURE [℃] SUPPLY VOLTAGE [V] Fig. 27 Fig. 28 Fig. 29 Output Sink Current – Ambient Temperature Input Offset Voltage – Supply Voltage Input Offset Voltage – Ambient Temperature (VOUT=1.5[V]) LM339 family . 160 LM339 family 160 100 0℃ 25℃ 80 60 40 70℃ 20 INPUT OFFSET CURRENT [nA] INPUT BIAS CURRENT [nA] 120 120 36V 100 80 5V 60 40 2V 20 0 10 20 30 40 SUPPLY VOLTAGE [V] Fig. 30 Input Bias Current – Supply Voltage 30 20 0℃ 10 0 25℃ -10 70℃ -20 -30 -40 0 0 LM339 family 50 40 140 140 INPUT BIAS CURRENT [nA] 70℃ 1.0 80 -8 10 25℃ 1.2 LM339 family 8 INPUT OFFSET VOLTAGE [mV] OUTPUT SINK CURR ENT [mA] 36V 0 1.4 (IOL=4[mA]) 30 10 1.6 Fig. 25 (IOL=4[mA]) 20 LM339 family 1.8 Output Saturation Voltage – Ambient Temperature LM339 family 80 0.0 0 Output Saturation Voltage – Supply Voltage 40 20 30 40 50 60 70 AMBIENT TEMPER ATURE [℃] 2.0 2V 200 10 Supply Current – Ambient Temperature 400 40 2V 0.2 0 LOW LEVEL OUTPUT VOLTAGE [V] OUTPUT SATU RATION VOLT AGE [mV] OUTPUT SATURATION VOLTAGE [mV] 25℃ 300 0.4 Fig. 23 500 70℃ 400 0.6 40 Derating Curve 500 36V 5V 0 0 INPUT OFFSET VOLTAGE [mV] 0 0.8 SUPPLY CURRENT [mA] LM339PWR SUPPLY CURRENT [mA] POWER DISSIPATION [mW] . 800 LM339 family 1 . 1000 -50 0 10 20 30 40 50 60 70 AMBIENT TEMPERATURE [℃] 80 0 10 20 30 SUPPLY VOLTAGE [V] 40 Fig. 31 Fig. 32 Input Bias Current – Ambient Temperature Input Offset Current – Supply Voltage (*)The data above is ability value of sample, it is not guaranteed. LM339family:0[℃]~+70[℃] www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 6/17 2011.06 - Rev.B LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR Technical Note 36V 30 20 10 5V 0 -10 2V -20 -30 -40 130 -50 LM339 family . 140 LARGE SIGNAL VOLT AGE GAIN [dB] IN PUT OFFSET CU RRENT [nA] 40 . LM339 family 50 LARGE SIGNAL VOLTAGE GAIN [dB] ●Reference Data LM339 family 25℃ 120 110 100 70℃ 0℃ 90 80 70 60 0 10 20 30 40 50 60 70 AMBIENT TEMPERATURE [℃] 80 0 10 20 30 SUPPLY VOLTAGE [V] Fig. 33 130 36V 120 110 100 5V 2V 90 80 70 60 0 40 10 20 30 40 50 60 70 AMBIENT TEMPERATURE [°C] Fig. 34 Fig. 35 Large Signal Voltage Gain – Supply Voltage Large Signal Voltage Gain – Ambient Temperature 80 . Input Offset Current – Ambient Temperature LM339 family 140 140 120 25℃ 0℃ 100 80 70℃ 60 40 0 10 20 30 SUPPLY VOLTAGE [V] LM339 family 140 130 120 36V 110 5V 100 90 80 2V 70 60 40 0 10 20 30 40 50 60 70 AMBIENT TEMPERATURE [°C] Fig. 36 3 5mV overdrive 2 20mV overdrive 1 100mV overdrive 0 10 20 30 40 50 60 70 AMBIENT TEMPERATURE [°C] 80 Fig. 39 Response Time (Low to High) – Ambient Temperature (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) 130 120 110 100 90 80 70 60 0 10 20 30 40 50 60 70 AMBIENT TEMPERAT URE [°C] 80 Power Supply Rejection Ratio – Ambient Temperature . LM339 family 5 RESPONSE TIME (HIGH to LOW) [μ ｓ] . . RESPONSE T IME (LOW to HIGH) [μs] 4 LM339 family 140 Fig. 38 Common Mode Rejection Ratio – Ambient Temperature LM339 family 0 80 Fig. 37 Common Mode Rejection Ratio – Supply Voltage 5 POWER SUPPLY REJECTION RATIO [dB] COMMON MODE REJECTION RATIO[dB] . POWER SUPPLY REJECTION RAT IO [dB] LM339 family 160 4 3 5mV overdrive 2 20mV overdrive 100mV overdrive 1 0 0 10 20 30 40 50 60 70 AMBIENT TEMPERATURE [°C] 80 Fig. 40 Response Time (High to Low) –Ambient Temperature (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) (*)The data above is ability value of sample, it is not guaranteed. BA10393F:-40[℃]~+70[℃] (*)上記のデータはサンプルの実力値であり、保証するものではありません。BA10393F:-40[℃]～+85[℃] www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 7/17 2011.06 - Rev.B LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR Technical Note ●Reference Data LM2903 family LM2903 family 800 1000 LM2903 family LM2903 family 1.6 1.6 1.4 600 LM2903DGKR 400 400 LM2903DT 200 200 SUPPLY CURRENT [mA] SUPPLY CURRENT [mA] LM2903PT 1.2 1.0 25℃ -40℃ 0.8 0.6 0.4 0.2 105℃ 0.0 00 25 25 50 50 75 75 100 100 125 125 AMBIENT TEMPERTURE [℃] AMBIENT TEMPERATURE . 10 20 30 Fig. 42 105℃ 100 25℃ -40℃ 0 30 150 2V 100 5V 50 36V -25 0 25 50 75 0 105℃ 0.6 0.4 -40℃ 100 125 0 150 2 4 6 8 75 10 12 16 18 (IOL=4[mA]) (VCC=5[V]) LM2903 family 8 6 6 4 -40℃ 2 0 25℃ -2 105℃ 20 Fig. 46 Low Level Output Voltage – Output Sink Current 8 125℃ -4 -6 100 125 150 14 OUTPUT SINK CURRENT [mA] 4 2V 2 0 5V -2 36V -4 -6 -8 -8 50 0.8 LM2903 family INPUT OFFSET VOLTAGE [mV] OUTPUT SINK CURRENT [mA] 10 25℃ 125℃ 1 Fig. 45 2V 25 1.2 Output Saturation Voltage – Ambient Temperature LM2903 family 0 1.4 0 -50 40 100 125 150 1.6 SUPPLY VOLTAGE [V] 20 75 0.2 40 36V 50 LM2903 family 0 (IOL=4[mA]) -25 25 1.8 Fig. 44 -50 0 2 Output Saturation Voltage – Supply Voltage 5V -25 Supply Current – Ambient Temperature 200 SUPPLY VOLTAGE [V] 30 -50 LM2903 family MAXIMUM OUTPUT VOLTAGE [mV] MAXIMUM OUTPUT VOLTAGE [mV] 125℃ 20 2V Fig. 43 LM2903 family 10 0.4 AMBIENT TEMPERATURE [℃] Supply Current – Supply Voltage 200 0 5V 0.6 SUPPLY VOLTAGE [V] [℃] Fig. 41 50 36V 0.8 40 Derating Curve 150 1.0 0.0 0 150 150 OUTPUT VOLTAGE [V] 00 1.2 0.2 125℃ INPUT OFFSET VOLTAGE [mV] POWER DISSIPATION POWER DISSIPATION Pd [mV] [mW] 1.4 800 600 0 10 20 30 -50 40 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [℃] SUPPLY VOLTAGE [V] AMBIENT TEMPERATURE [℃] Fig. 47 Fig. 48 Fig. 49 Output Sink Current – Ambient Temperature Input Offset Voltage – Supply Voltage Input Offset Voltage – Ambient Temperature (VOUT=1.5[V]) LM2903 family LM2903 family 50 140 140 40 120 -40℃ 100 25℃ 80 60 40 105℃ 20 120 100 36V 80 60 40 5V 20 125℃ INPUT OFFSET CURRENT[nA] 160 INPUT BIAS CURRENT [nA] INPUT BIAS CURRENT [nA] LM2903 family 160 0 5 10 15 20 25 30 35 SUPPLY VOLTAGE [V] Fig. 50 Input Bias Current – Supply Voltage 20 -40℃ 10 25℃ 0 -10 105℃ 125℃ -20 -30 -40 2V 0 0 30 -50 -50 -25 0 25 50 75 100 125 150 0 10 20 30 40 AMBIENT TEMPERATURE [℃] SUPPLY VOLTAGE [V] Input Bias Current – Ambient Temperature Input Offset Current – Supply Voltage Fig. 51 Fig. 52 (*)The data above is ability value of sample, it is not guaranteed.LM2903family:-40[℃]～+125[℃] www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 8/17 2011.06 - Rev.B LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR Technical Note ●Reference Data LM2903 family LM2903 family 30 20 2V 10 0 -10 5V -20 36V -30 -40 -50 -50 -25 0 25 50 75 130 140 LARGE SINGAL VOLTAGE GAIN [dB] 40 LM2903 family LM2903 family 140 LARGE SINGAL VOLTAGE GAIN [dB] INPUT OFFSET CURRENT [nA] 50 105℃ 125℃ 120 110 100 25℃ -40℃ 90 80 70 60 100 125 150 0 10 AMBIENT TEMPERATURE [℃] 20 30 130 36V 120 110 100 80 70 60 -50 40 5V 15V 90 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [℃] SUPPLY VOLTAGE [V] Fig. 54 Fig. 55 Large Signal Voltage Gain – Supply Voltage Large Signal Voltage Gain – Ambient Temperature 125℃ 105℃ 100 80 25℃ -40℃ 60 40 0 10 20 30 40 125 36V 100 75 5V 2V 50 25 0 -25 0 25 Fig. 56 50 75 160 140 120 100 80 60 25 50 75 3 2 125℃ 0 -80 -60 -40 -20 Fig. 60 RESPONSE TIME (HIGH TO LOW)[μs] 3 125℃ 105℃ -40℃ 1 0 80 3 4 5 Input Offset Voltage – Input Voltage (VCC=5V) 5 4 3 100mV overdrive 20mV overdrive 5mV overdrive 2 1 0 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [℃] Response Time (Low to High) – Ambient Temperature (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) LM2903 family 4 60 2 Fig. 61 (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) 5 40 0 OVER DRIVE VOLTAGE [V] LM2903 family RESPONSE TIME (HIGH TO LOW)[μs] -40℃ 25℃ 1 -100 100 125 150 105℃ Response Time (Low to High) – Over Drive Voltage 20 1 LM2903 family 4 Fig. 59 0 0 Fig. 58 Power Supply Rejection Ratio – Ambient Temperature 25℃ -1 INPUT VOLTAGE [V] 5 AMBIENT TEMPERATURE [℃] 2 -4 100 125 150 LM2903 family RESPONSE TIME (LOW TO HIGH)[μs] POWER SUPPLY REJECTION RATIO [dB] 180 0 -2 Fig. 57 LM2903 family -25 125℃ 0 Common Mode Rejection Ratio – Ambient Temperature 200 -50 -40℃ 2 AMBIENT TEMPERATURE [℃] SUPPLY VOLTAGE [V] Common Mode Rejection Ratio – Supply Voltage 105℃ 25℃ 4 -6 -50 RRESPONSE TIME (LOW TO HIGH)[μs] 120 6 150 INPUT OFFSET VOLTAGE [mV] 140 LM2903 family LM2903 family LM2903 family 160 COMMON MODE REJECTION RATIO [dB] COMMON MODE REJECTION RATIO [dB] Fig. 53 Input Offset Current – Ambient Temperature 100 OVER DRIVE VOLTAGE [V] Fig. 62 Response Time (High to Low) – Over Drive Voltage (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) 5 4 100mV overdrive 3 20mV overdrive 5mV overdrive 2 1 0 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [℃] Fig. 63 Response Time (High to Low) – Ambient Temperature (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) (*)The data above is ability value of sample, it is not guaranteed. LM2903family:-40[℃]～+125[℃] www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 9/17 2011.06 - Rev.B LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR Technical Note ●Reference Data LM2901 family LM2901 family 1000 1000 LM2901 family 2.0 LM290PWR 600 600 400 400 LM2901DR 200 200 1.4 25℃ 1.6 -40℃ 1.4 1.2 1.0 0.8 0.6 125℃ 0.4 25 50 25 75 50 100 75 125 100 125 AMBIENT TEMPERATURE [℃] AMBIENT TEMPERATURE [℃] 150 0 150 10 20 Fig. 64 LM2901 family 25℃ -40℃ 20 30 150 2V 100 5V 36V 50 -50 -25 0 25 50 75 100 125 10 0 50 75 25℃ 125℃ 1.2 1 0.8 105℃ 0.6 0.4 -40℃ 0 2 4 6 8 0 -2 125℃ -4 -6 100 125 150 16 18 20 (VCC=5[V]) 2 105℃ 14 Fig. 69 -40℃ 25℃ 12 Low Level Output Voltage – Output Sink Current 6 4 10 OUTPUT SINK CURRENT [mA] LM2901 family 8 6 4 2V 2 0 5V -2 36V -4 -6 -8 -8 25 1.4 150 LM2901 family 8 INPUT OFFSET VOLTAGE [mV] 2V 0 1.6 (IOL=4[mA]) 20 -25 LM2901 family Output Saturation Voltage – Ambient Temperature 36V 100 125 150 2 SUPPLY VOLTAGE [V] LM2901 family 75 Supply Current – Ambient Temperature Fig. 68 40 50 0 40 (IOL=4[mA]) -50 25 0.2 Fig. 67 5V 0 1.8 Output Saturation Voltage – Supply Voltage 30 -25 AMBIENT TEMPERATURE [℃] LM2901 family SUPPLY VOLTAGE [V] OUTPUT SINK CURRENT [mA] -50 INPUT OFFSET VOLTAGE [mV] 10 2V 40 0 0 0 0.4 Fig. 66 200 MAXIMUM OUTPUT VOLTAGE [mV] MAXIMUM OUTPUT VOLTAGE [mV] 105℃ 100 50 5V 0.6 Fig. 65 200 125℃ 30 Supply Current – Supply Voltage Derating Curve 150 36V 0.8 SUPPLY VOLTAGE [V] OUTPUT VOLTAGE [V] 0 1.0 0.0 0.0 0 1.2 0.2 105℃ 0.2 00 SUPPLY CURRENT [mA] SUPPLY CURRENT [mA] POWER DISSIPATION [mW] POWER DISSIPATION Pd [mW] 1.8 800 800 LM2901 family 1.6 0 10 AMBIENT TEMPERATURE [℃] 20 30 -50 40 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [℃] SUPPLY VOLTAGE [V] Fig. 70 Fig. 71 Fig. 72 Output Sink Current – Ambient Temperature Input Offset Voltage – Supply Voltage Input Offset Voltage – Ambient Temperature (VOUT=1.5[V]) LM2901 family 120 25℃ -40℃ 100 80 60 40 105℃ 20 125℃ 140 120 100 36V 80 60 40 5V 20 2V 0 0 0 5 10 15 20 25 30 35 SUPPLY VOLTAGE [V] 50 INPUT OFFSET CURRENT[nA] 140 LM2901 family LM2901 family 160 INPUT BIAS CURRENT [nA] INPUT BIAS CURRENT [nA] 160 40 30 20 -40℃ 10 25℃ 0 -10 105℃ 125℃ -20 -30 -40 -50 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [℃] 0 10 20 30 40 SUPPLY VOLTAGE [V] Fig. 73 Fig. 74 Fig. 75 Input Bias Current – Supply Voltage Input Bias Current – Ambient Temperature Input Offset Current – Supply Voltage (*)The data above is ability value of sample, it is not guaranteed. LM901family:-40[℃]～+125[℃] www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 10/17 2011.06 - Rev.B LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR Technical Note ●Reference Data LM2901 family LM2901 family 30 20 2V 10 0 -10 36V 5V -20 -30 -40 -50 -50 -25 0 25 50 75 130 125℃ 105℃ 120 110 100 25℃ -40℃ 90 80 70 60 100 125 150 0 10 AMBIENT TEMPERATURE [℃] 20 30 Fig. 76 100 25℃ -40℃ 60 40 20 30 40 125 36V 100 75 5V 2V 50 25 120 100 80 60 75 -25 0 25 50 75 2 105℃ 125℃ 0 -80 -60 -20 0 Fig. 83 RESPONSE TIME (HIGH TO LOW)[μs] 105℃ -40℃ 1 0 60 80 -2 -4 -1 0 100 OVER DRIVE VOLTAGE [V] Fig. 85 Response Time (High to Low) – Over Drive Voltage (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) 1 2 3 4 5 Input Offset Voltage – Input Voltage (VCC=5V) LM2901 family 5 4 3 5mV overdrive 100mV overdrive 20mV overdrive 2 1 0 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [℃] Fig. 84 (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) 125℃ 40 -40 Response Time (Low to High) – Over Drive Voltage 4 20 -40℃ OVER DRIVE VOLTAGE [V] LM2901 family 0 25℃ 1 Fig. 82 25℃ 125℃ 0 Fig. 81 3 Power Supply Rejection Ratio – Ambient Temperature 2 -40℃ 2 INPUT VOLTAGE [V] 4 AMBIENT TEMPERATURE [℃] 5 105℃ 100 125 150 5 -100 100 125 150 100 125 150 -6 -50 RRESPONSE TIME (LOW TO HIGH)[μs] 140 75 LM2901 family RESPONSE TIME (LOW TO HIGH)[μs] POWER SUPPLY REJECTION RATIO [dB] 160 50 4 AMBIENT TEMPERATURE [℃] 180 3 25 LM2901 family 0 LM2901 family 50 0 25℃ Fig. 80 25 -25 6 Common Mode Rejection Ratio – Ambient Temperature 0 60 Fig. 78 Fig. 79 -25 70 Large Signal Voltage Gain – Ambient Temperature Common Mode Rejection Ratio – Supply Voltage -50 80 AMBIENT TEMPERATURE [℃] 150 SUPPLY VOLTAGE [V] 200 5V 15V 90 -50 40 INPUT OFFSET VOLTAGE [mV] 125℃ 10 100 LM2901 family COMMON MODE REJECTION RATIO [dB] COMMON MODE REJECTION RATIO [dB] 140 0 110 Large Signal Voltage Gain – Supply Voltage LM2901 family 80 36V 120 Fig. 77 160 105℃ 130 SUPPLY VOLTAGE [V] Input Offset Current – Ambient Temperature 120 LARGE SINGAL VOLTAGE GAIN [dB] LARGE SINGAL VOLTAGE GAIN [dB] INPUT OFFSET CURRENT [nA] 140 140 40 RESPONSE TIME (HIGH TO LOW)[μs] LM2901 family LM2901 family 50 Response Time (Low to High) – Ambient Temperature (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) LM2901 family 5 4 100mV overdrive 3 20mV overdrive 5mV overdrive 2 1 0 -50 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE [℃] Fig. 86 Response Time (High to Low) – Ambient Temperature (VCC=5[V],VRL=5[V],RL=5.1[kΩ]) (*)The data above is ability value of sample, it is not guaranteed. LM901family:-40[℃]～+125[℃] www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 11/17 2011.06 - Rev.B LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR Technical Note ●Circuit Diagram Vcc OUT IN+ IN- GND Fig.87 Circuit Diagram (each Comparator) ●Measurement circuit 1 NULL Method measurement condition Parameter VF S1 S2 S3 Input Offset Voltage VF1 ON ON Input Offset Current VF2 OFF OFF VF3 OFF ON VF4 ON OFF ON ON Input Bias Current VF5 Large Signal Voltage Gain VF6 Vcc,GND,EK,VICR Unit：[V］ LM2903/LM2901 family Calculation Vcc GND EK VICR LM393/LM339 family GND EK VICR ON 5 to 30 0 -1.4 0 5 to 30 0 -1.4 0 1 ON 5 0 -1.4 0 5 0 -1.4 0 2 5 0 -1.4 0 5 0 -1.4 0 5 0 -1.4 0 5 0 -1.4 0 15 0 -1.4 0 15 0 -1.4 0 15 0 -11.4 0 15 0 -11.4 0 ON ON Vcc 3 4 －Calculation－ 1.Input offset voltage (VIO) Vio VF1 1+ Rf /Rs 0.1[μF] [V] S1 2.Input offset current (IIO) Iio VF2 - VF1 Ri (1+ R f / Rs) 500[kΩ] 0.1[μF] RS＝ 50[Ω] [A] +15[V ] Ri＝ 10[kΩ] Ri＝ 10[kΩ] 3.Input bias current (IIb) RK 500[kΩ] DUT [A] 2× R i (1+ Rf / Rs) 50[kΩ] S2 NULL S3 RS＝ 50[Ω] VF4 - VF3 RK EK Vcc V ICR Ib Rf 50[kΩ] GND RL 1000[pF] -15[V ] V VF V RL 4.Large signal differential voltage gain (AVD) AV 20× Log 10× (1+ Rf /Rs) Fig.88 Measurement Circuit1 (each Comparator) [dB] VF6 - VF5 www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 12/17 2011.06 - Rev.B LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR Technical Note ●Measurement Circuit2 Switch Condition SW No. Supply Current ― SW 1 SW 2 SW 3 SW 4 SW 5 SW 6 SW 7 OFF OFF OFF OFF OFF OFF OFF Low Level Output Current VOL=1.5[V] OFF ON ON OFF ON ON OFF Low Level Output Current IOL=4[mA] OFF ON ON OFF OFF OFF ON High Level Output Current VOH=36[V] OFF ON ON OFF OFF OFF ON ON OFF ON ON OFF ON OFF RL=5.1[kΩ] Response Time VRL=5[V] Vcc 5[V] A － SW1 SW2 ＋ SW3 SW4 GND 0[V] SW5 SW6 SW7 RL A VIN- VIN+ V VRL VOL/VOH Fig.89 Measurement Circuit2 (each channel) Input waveform Input waveform VIN VIN over drive +100[mV] 0[V] 0[V] +100[mV] over drive VUOT VUOT Output waveform Output waveform 5[V] 5[V] 2.5[V] 2.5[V] 0[V] 0[V] Tre LH Tre LH Fig.90 Response Time www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 13/17 2011.06 - Rev.B LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR Technical Note ●Description of Electrical Characteristics Described below are descriptions of the relevant electrical terms. Please note that item names, symbols, and their meanings may differ from those on another manufacturer’s documents. 1. Absolute maximum ratings The absolute maximum ratings are values that should never be exceeded, since doing so may result in deterioration of electrical characteristics or damage to the part itself as well as peripheral components. 1.1 Power supply voltage (Vcc/GND) Expresses the maximum voltage that can be supplied between the positive and negative power supply terminals without causing deterioration of the electrical characteristics or destruction of the internal circuitry. 1.2 Differential input voltage (VID) Indicates the maximum voltage that can be supplied between the non-inverting and inverting terminals without damaging the IC. 1.3 Input common-mode voltage range (VICR) Signifies the maximum voltage that can be supplied to non-inverting and inverting terminals without causing deterioration of the electrical characteristics or damage to the IC itself. Normal operation is not guaranteed within the input common-mode voltage range of the maximum ratings – use within the input common-mode voltage range of the electric characteristics instead. 1.4 Operating temperature range and storage temperature range (Topr,Tstg) The operating temperature range indicates the temperature range within which the IC can operate. The higher the ambient temperature, the lower the power consumption of the IC. The storage temperature range denotes the range of temperatures the IC can be stored under without causing excessive deterioration of the electrical characteristics. 1.5 Power dissipation (Pd) Indicates the power that can be consumed by a particular mounted board at ambient temperature (25°C). For packaged products, Pd is determined by maximum junction temperature and the thermal resistance. 2. Electrical characteristics 2.1 Input offset voltage (VIO) Signifies the voltage difference between the non-inverting and inverting terminals. It can be thought of as the input voltage difference required for setting the output voltage to 0V. 2.2 Input offset current (IIO) Indicates the difference of the input bias current between the non-inverting and inverting terminals. 2.3 Input bias current (IIB) Denotes the current that flows into or out of the input terminal, it is defined by the average of the input bias current at the non-inverting terminal and the input bias current at the inverting terminal. 2.4 Input common-mode voltage range (VICR) Indicates the input voltage range under which the IC operates normally. 2.5 Large signal differential voltage gain (AVD) The amplifying rate (gain) of the output voltage against the voltage difference between the non-inverting and inverting terminals, it is (normally) the amplifying rate (gain) with respect to DC voltage. AVD = (output voltage fluctuation) / (input offset fluctuation) 2.6 Supply current (ICC) Indicates the current of the IC itself that flows under specific conditions and during no-load steady state. 2.7 Low level output current (IOL) Denotes the maximum current that can be output under specific output conditions. 2.8 Low level output voltage (VOL) Signifies the voltage range that can be output under specific output conditions. 2.9 High level output current (IOH) Indicates the current that flows into the IC under specific input and output conditions. 2.10 Response time (tre) The interval between the application of input and output conditions. 2.11 Common-mode rejection ratio (CMRR) Denotes the ratio of fluctuation of the input offset voltage when the in-phase input voltage is changed (DC fluctuation). CMRR = (change of input common-mode voltage) / (input offset fluctuation) 2.12 Power supply rejection ratio (PSRR) Signifies the ratio of fluctuation of the input offset voltage when the supply voltage is changed (DC fluctuation). PSRR = (change in power supply voltage) / (input offset fluctuation) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 14/17 2011.06 - Rev.B LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR Technical Note ●Derating Curves 1000 LM393PWR LM2903PWR/VQPWR 600 POWER DISSIPATION Pd [mW] POWER DISSIPATION Pd [mW] 800 LM393PWR LM2903PWR/VQPWR 400 200 LM393DR LM2903DR/VQDR 0 0 25 50 75 100 125 150 LM339DR LM2901DR/VQDR 600 400 200 0 0 AMBIENT TEMPERATURE [℃] 25 50 75 100 125 150 AMBIENT TEMPERATURE [℃] LM393DR/PWR/DGKR LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR LM2901DR/PWR/VQDR/VQPWR Power Dissipation Package LM339PWR LM2901PWR/VQPWR 800 Power Dissipation Pd[W] θja [℃/W] Package Pd[W] θja [℃/W] SOIC8 (*8) 450 3.6 SOIC14 610 4.9 TSSOP8 (*6) 500 470 4.0 TSSOP14 870 7.0 MSOP8/VSSOP8 (*7) 3.76 θja = (Tj-Ta)/Pd[℃/W] θja = (Tj-Ta)/Pd[℃/W] Fig.91 Derating Curves V cc ●Precautions 1) Unused circuits When there are unused circuits it is recommended that they be connected as in Fig.92, setting the non-inverting input terminalto a potential within the in-phase input voltage range (VICR). － ＋ 2) Input terminal voltage Applying GND + 36V to the input terminal is possible without causing deterioration of the electrical characteristics or destruction, irrespective of the supply voltage. However, this does not ensure normal circuit operation. Please note that the circuit operates normally only when the input voltage is within the common mode input voltage range of the electric characteristics. GND Fig.92 Disable circuit example 3) Power supply (single / dual) The op-amp operates when the specified voltage supplied is between Vcc and GND. Therefore, the single supply op-amp can be used as a dual supply op-amp as well. 4) Power dissipation Pd Using the unit in excess of the rated power dissipation may cause deterioration in electrical characteristics due to a rise in chip temperature, including reduced current capability. Therefore, please take into consideration the power dissipation (Pd) under actual operating conditions and apply a sufficient margin in thermal design. Refer to the thermal derating curves for more information. 5) Short-circuit between pins and erroneous mounting Incorrect mounting may damage the IC. In addition, the presence of foreign particles between the outputs, the output and the power supply, or the output and GND may result in IC destruction. 6) Terminal short-circuits When the output and Vcc terminals are shorted, excessive output current may flow, resulting in undue heat generation and, subsequently, destruction. 7) Operation in a strong electromagnetic field Operation in a strong electromagnetic field may cause malfunctions. 8) Radiation This IC is not designed to withstand radiation. 9) IC handing Applying mechanical stress to the IC by deflecting or bending the board may cause fluctuations in the electrical characteristics due to piezoelectric (piezo) effects. 10) Board inspection Connecting a capacitor to a pin with low impedance may stress the IC. Therefore, discharging the capacitor after every process is recommended. In addition, when attaching and detaching the jig during the inspection phase, ensure that the power is turned OFF before inspection and removal. Furthermore, please take measures against ESD in the assembly process as well as during transportation and storage. www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. 15/17 2011.06 - Rev.B LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR Technical Note ●Ordering part number L M 2 9 0 3 Family name LM393 LM339 LM2901 LM2903 V Q D R Operating Voltage Package type VQ : Tested to 32V None : Tested to 30V D : SOIC PW : TSSOP DGK : MSOP/VSSOP Packaging and forming specification R: Embossed tape and reel SOIC8 <Tape and Reel information> 4.9±0.2 (MAX 5.25 include BURR) 6 5 0.45Min. 7 3.9±0.2 6.0±0.3 8 4° +6° −4° 1 2 3 Tape Embossed carrier tape Quantity 2500pcs Direction of feed ( reel on the left hand and you pull out the tape on the right hand The direction is the 1pin of product is at the upper left when you hold ) 4 0.545 0.2±0.1 0.175 1.375±0.1 S 1.27 0.42±0.1 1pin 0.1 S Reel (Unit : mm) Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. SOIC14 <Tape and Reel information> 8.65±0.1 (Max 9.0 include BURR) 0.65± 0.15 1 1PIN MARK Tape Embossed carrier tape Quantity 2500pcs Direction of feed ( reel on the left hand and you pull out the tape on the right hand The direction is the 1pin of product is at the upper left when you hold ) 7 0.175± 0.075 S +0.05 0.22 −0.03 1.375± 0.075 1.65MAX 0.515 1.05±0.2 8 6.0 ± 0.2 3.9 ± 0.1 14 4° +6° −4° +0.05 0.42 −0.04 1.27 0.08 S 0.08 M 1pin Reel (Unit : mm) Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. TSSOP8 <Tape and Reel information> 3.0±0.1 (MAX 3.35 include BURR) 7 6 0.5 ± 0.15 3 2500pcs Direction of feed ( reel on the left hand and you pull out the tape on the right hand 4 1PIN MARK The direction is the 1pin of product is at the upper left when you hold ) 1.0±0.2 2 Embossed carrier tape Quantity +0.05 0.145 −0.03 1.0 ± 0.05 S 0.1 ± 0.05 1.2MAX 1 0.525 Tape 5 6.4 ± 0.2 4.4 ± 0.1 8 4±4 0.08 S +0.05 0.245 −0.04 0.08 M 1pin 0.65 (Unit : mm) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. Reel 16/17 Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. 2011.06 - Rev.B LM393DR/PWR/DGKR,LM2903DR/PWR/DGKR/VQDR/VQPWR LM339DR/PWR,LM2901DR/PWR/VQDR/VQPWR Technical Note TSSOP14 <Tape and Reel information> 5.0±0.1 (Max 5.35 include BURR) 4 ±4 14 1 Tape Embossed carrier tape Quantity 2500pcs Direction of feed ( reel on the left hand and you pull out the tape on the right hand The direction is the 1pin of product is at the upper left when you hold ) 7 1PIN MARK +0.05 0.145 −0.03 0.1±0.05 S 1.0±0.05 1.2MAX 0.55 1.0±0.2 0.5±0.15 6.4±0.2 4.4±0.1 8 0.08 S +0.05 0.245 −0.04 0.65 0.08 1pin M Reel (Unit : mm) Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. MSOP / VSSOP8 <Tape and Reel information> 3.0±0.1 (MAX 3.35 include BURR) 6 5 0.45 ± 0.15 2 3 4 1PIN MARK Tape Embossed carrier tape Quantity 2500pcs Direction of feed ( reel on the left hand and you pull out the tape on the right hand The direction is the 1pin of product is at the upper left when you hold ) 0.95 ± 0.2 1 +0.05 0.145 −0.03 0.525 0.1±0.05 S 0.85±0.05 1.1MAX 7 3.0 ± 0.1 4.9± 0.2 8 4±4 0.08 S +0.05 0.32 −0.04 0.08 M 1pin 0.65 (Unit : mm) www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. Reel 17/17 Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. 2011.06 - Rev.B Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2011 ROHM Co., Ltd. All rights reserved. R1120A