CMO5 Series 5V 5x7mm Surface Mount Crystal Clock Oscillators TTL/CMOS Compatible Tri-State Feature for Auto Test Systems Tape & Reel Packaging ±20ppm Available - Please Contact Factory E L E C T R I C A L S P E C I F I C AT I O N S MODEL CMO5 Frequency Range (MHz) 1.5 to 156.250 Frequency Stability (ppm) Overall (Typical) Inclusive of calibration, temperature, voltage, load, shock,vibration, aging 0°C to 70°C ±25 -40°C to +85°C ±50 Temperature Range (°C) Operating -40°C to +85°C Storage -40°C to +125°C Supply Voltage (V) Input Current (mA) +5.0 ±10% 1.5MHz to 30MHz >30MHz to 50MHz <10 <30 <50 Symmetry (%) TTL/CMOS Transistion Times >50MHz to 156.250MHz 45/55 1.5MHz to 50MHz >50MHz to 156.250MHz Rise Time (ns) <5 <3 Fall Time (ns) <5 <3 Load 10TTL/15pF “0” Level (VOL) “1” Level (VOH) 0.5V 2.4V/4.5V Start up Time (ms) <10 PA R T N U M B E R I N G G U I D E CMO5XXXX - Specify Frequency “C” = CMOS “T” = TTL “Blank” = 0oC to 70oC Operating Temp. “M” = -40oC to 85oC Operating Temp. “A” = ±25ppm (-40oC to 85oC Excluding Aging) “B” = ±50ppm “C” = ±100ppm “D” = ±20ppm Excluding Aging (Contact Factory) “Blank” = Fixed Frequency “E” = Tri-State 2553 N. Edgington Street, Franklin Park, IL 60131 y Phone: 847.451.1000 y Fax: 847.451.7585 800-888-1499 or www.champtech.com 1 CMO5 Series 5V 5x7mm Surface Mount Crystal Clock Oscillators PIN OUTPUT WAVEFORM FUNCTION 1 N/C / Tri-State 2 Ground 3 Output 4 + VCC TEST CIRCUIT DIAGRAM MECHANICAL AND ENVIRONMENTAL SPECIFICATIONS TEST METHODS REFERENCE PROCEDURES DESCRIPTION Temperature Cycle MIL-STD-833, Mtd 1010, Cond. B -55°C to +125°C; Air-to-Air; 100 cycles; 10 min. dwell Mechanical Shock MIL-STD-883, Mtd 2002, Cond. B 1500 g’s Vibration MIL-STD 883, Mtd 2007, Cond. B 20-2000 Hz; 0.06 inch; 15g’s; 3 planes Humidity Steady State MIL-STD-202, Mtd 103 40°C; 90%-95% R.H.; 56 days Thermal Shock MIL-STD-883, Mtd 1011.7 Cond. B 100°C to 0°C; Water-to-Water; 15 cycles Electrostatic Discharge MIL-STD-883, Mtd 3015 Class II 2 KV to 4 KV Threshold Solderability Hermeticity MIL-STD-883, Mtd 2022.2 MIL-STD-883, Mtd 1014.8, Cond. A1 Solder dip; Meniscograph Criteria Mass spectro. 2 x 10-8 atmos. CC/sec He Resistance to Soldering Lead Integrity MIL-STD-202, Mtd 210D, Cond. J 235°C; 30 seconds MIL-STD-883, Mtd 2004.5, Cond. A, B1 Lead tension & bend stress Marking Permanence Life Test MIL-STD-883, Mtd 2015.8 MIL-STD-883, Mtd 1005.6 Resistance to solvents 125°C, powered, 1000 hours minimum 2553 N. Edgington Street, Franklin Park, IL 60131 y Phone: 847.451.1000 y Fax: 847.451.7585 800-888-1499 or www.champtech.com 2