HMC433 / 433E v02.0705 FREQUENCY DIVIDERS & DETECTORS - SMT 5 SMT GaAs HBT MMIC DIVIDE-BY-4, DC - 8.0 GHz Typical Applications Features Prescaler for DC to C Band PLL Applications: Ultra Low SSB Phase Noise: -150 dBc/Hz • UNII, Point-to-Point & VSAT Radios Single-Ended I/O’s • 802.11a & HiperLAN WLAN Output Power: -2 to -3.5 dBm • Fiber Optic Single DC Supply: +3V @ 53 mA • Cellular / 3G Infrastructure 9 mm2 Ultra Small Package: SOT26 Functional Diagram General Description The HMC433 & HMC433E are low noise Divide-by-4 Static Dividers utilizing InGaP GaAs HBT technology in ultra small surface mount SOT26 plastic packages. This device operates from DC (with a square wave input) to 8.0 GHz input frequency with a single +3.0V DC supply. Single-ended inputs and outputs reduce component count and cost. The low additive SSB phase noise of -150 dBc/Hz at 100 kHz offset helps the user maintain good system noise performance. Electrical Specifications, TA = +25° C, 50 Ohm System, Vcc= +3V Parameter Conditions Maximum Input Frequency Minimum Input Frequency Input Power Range Output Power Reverse Leakage SSB Phase Noise (100 kHz offset) Output Transition Time Supply Current (Icc) Min. Typ. 8 8.5 Sine Wave Input. [1] Max. GHz 0.2 Fin= 1 to 6 GHz Fin= 6 to 8 GHz -12 -3 -15 -7 Fin= 4 GHz Fin= 8 GHz -5.0 -6.5 -2.0 -3.5 GHz +12 +10 dBm dBm dBm dBm RF Output Terminated, Fin= 4 GHz, Pin= 0 dBm -25 dBm Pin= 0 dBm, Fin= 4 GHz -150 dBc/Hz Pin= 0 dBm, Fout= 882 MHz 120 ps Vcc= +3.0V 53 mA 1. Divider will operate down to DC for square-wave input signal. 5 - 72 Units For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC433 / 433E v02.0705 SMT GaAs HBT MMIC DIVIDE-BY-4, DC - 8.0 GHz 20 15 15 10 10 Recommended Operating Window 0 -5 -10 -15 5 Min Pin +25 C Max Pin +25 C Min Pin -40 C Max Pin -40 C Min Pin +85 C Max Pin +85 C 0 -5 -10 -15 -20 -20 0 1 2 3 4 5 6 7 8 9 10 0 1 2 3 INPUT FREQUENCY (GHz) 4 5 6 7 8 9 10 INPUT FREQUENCY (GHz) SSB Phase Noise Performance, Pin= 0 dBm, T= 25 °C Output Power vs. Temperature 0 0 SSB PHASE NOISE (dBc/Hz) OUTPUT POWER (dBm) -20 -2 -4 +25 C -40 C +85 C -6 -8 -10 0 1 2 3 4 5 6 7 8 9 -40 -60 -80 -100 -120 -140 -160 2 10 10 3 INPUT FREQUENCY (GHz) 5 10 6 10 7 10 10 OFFSET FREQUENCY (Hz) Output Harmonic Content, Pin= 0 dBm, T= 25 °C Reverse Leakage, Pin= 0 dBm, T= 25 °C 0 0 -10 POWER LEVEL (dBm) -10 OUTPUT LEVEL (dBm) 4 10 FREQUENCY DIVIDERS & DETECTORS - SMT 20 5 5 Input Sensitivity Window vs. Temperature INPUT POWER (dBm) INPUT POWER (dBm) Input Sensitivity Window, T= 25 °C -20 -30 Pfeedthru 2nd Harmonic 3rd Harmonic -40 -20 -30 -40 -50 -50 -60 0 1 2 3 4 5 6 7 INPUT FREQUENCY (GHz) 8 9 10 0 1 2 3 4 5 6 7 8 9 10 INPUT FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 5 - 73 HMC433 / 433E v02.0705 5 SMT GaAs HBT MMIC DIVIDE-BY-4, DC - 8.0 GHz Output Voltage Waveform, Pin= 0 dBm, Fout= 882 MHz, T= 25 °C Absolute Maximum Ratings RF Input (Vcc= +3.0V) +15 dBm Vcc +3.5V 150 Maximum Channel Temperature 135 °C 100 Continuous Pdiss (T=85 °C) (derate 5mW/°C above 85 °C) 250mW 250 200 AMPLITUDE (mV) FREQUENCY DIVIDERS & DETECTORS - SMT 300 50 0 -50 -100 -150 -200 -65 to +150 °C Operating Temperature -40 to +85 °C ESD Sensitivity (HBM) Class 1A DC blocking capacitors are required at RF input and RF output ports. Choose value for lowest frequency of operation. -250 -300 23 Storage Temperature 23.2 23.4 23.6 23.8 24 24.2 24.4 24.6 24.8 25 ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS TIME (nS) Typical Supply Current vs. Vcc Vcc (V) Icc (mA) 2.70 42 3.0 53 3.30 63 Note: Divider will operate over full voltage range shown above Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOT FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC433 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 HMC433E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 Package Marking [3] [1] H433 XXXX [2] 433E XXXX [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX 5 - 74 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC433 / 433E v02.0705 SMT GaAs HBT MMIC DIVIDE-BY-4, DC - 8.0 GHz Pin Number Function Description 1, 4 N/C No Connection 2 GND Pin must connect ro RF/DC ground. 3 IN RF input must be DC blocked. 5 Vcc Supply voltage 3V ± 0.3V. 6 OUT Divided output must be DC blocked. Interface Schematic For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com FREQUENCY DIVIDERS & DETECTORS - SMT 5 Pin Description 5 - 75 HMC433 / 433E v02.0705 FREQUENCY DIVIDERS & DETECTORS - SMT 5 SMT GaAs HBT MMIC DIVIDE-BY-4, DC - 8.0 GHz Evaluation PCB Note: Line lengths on pins 1 & 4 (N/C) are not necessary. List of Materials for Evaluation PCB 105675 Item Description J1 - J2 PCB Mount SMA RF Connector J3 - J4 DC Pin C1 - C2 100 pF Capacitor, 0402 Pkg. C3 1000 pF Capacitor, 0402 Pkg. C4 10 μF Tantalum Capacitor, 1206 Pkg. U1 HMC433 / HMC433E Divide-by-4 PCB [2] 105199 Eval Board [1] The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 5 - 76 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC433 / 433E SMT GaAs HBT MMIC DIVIDE-BY-4, DC - 8.0 GHz Application Circuit Note: DC blocking capacitor values (C1, C2) and DC decoupling capacitor values (C3, C4) are chosen for lowest frequency of operation. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 5 FREQUENCY DIVIDERS & DETECTORS - SMT v02.0705 5 - 77