www.fairchildsemi.com FAN5230 System Electronics Regulator for Mobile PCs Features Description • • • • • • • • • • • • • • • The FAN5230 is a high efficiency and high precision multiple-output voltage regulator for notebook PC and other similar battery-powered applications. It integrates three pulse-width modulated (PWM) switching regulator controllers and two linear regulators to convert 5.4V-to-24V notebook battery power into the voltage used by the circuitry that surrounds the microprocessor in these systems. • • • • • • 5.4V to 24V input voltage range Five regulated outputs: 5V @ 5A (PWM) 3.3V @ 5A (PWM) 5V @ 50mA Always On (Linear) 3.3V @ 50mA Always On (Linear) 12V/Adjustable @ 120mA Boost (PWM) >96% efficiency Hysteretic mode for light loads PWM mode for normal loads Main regulators switch out of phase 300kHz fixed frequency switching RDS(ON) current sense over-current Reduced BOM; Max. efficiency Optional current sense resistor for precision over-current detect Power Good signal for all voltages Input under-voltage lock-out (UVLO) Thermal shutdown ACPI compliant 24-pin QSOP 2nd source by Intersil (IPM6220) Applications • Notebook PCs • Web tablets • Battery-powered instruments The two primary PWM controllers in the FAN5230 use synchronous-mode rectification to provide 3.3V and 5V at over 5A each. They switch out-of-phase to minimize input ripple-current. Utilization of both input and output voltage feedback in a current-mode control allows for fast and stable loop response over a wide range of input and output variations. PWM control in normal operation and hysteretic control under light load provides efficiency of greater than 95% over a wide range of input and output variations. The third PWM controller generates 12V at 120mA. A proprietary technology is used for accurate [± 1%] sensing of output current using the RDS(ON) of the external MOSFETs, eliminating external current sense resistors which saves board space and reduces BOM cost. Two integrated linear regulators provide stand-by ALWAYSON power at 3.3V and 5V for light (50mA) loads. Additional FAN5230 features include over-voltage, under-voltage, and over-current monitors and thermal shutdow protection. A single Power-Good signal is issued when soft start is completed and all outputs are within ± 10% of their settings. REV. 2.8.5 10/17/01 FAN5230 Typical Application Vin = 5.4-24V FAN5230 3.3V-ALWAYS@50mA 2 3.3 ALW 5V-ALWAYS 5V-ALWAYS CPUMP5 24 1 VIN HSD5 23 5V @ 5A + SW5 22 3 CPUMP3.3 4 HSD3.3 ISEN5 21 5 SW3.3 LSD5 20 6 5V-ALW GND5 19 7 LSD3.3 VFB5 18 8 GND3.3 SDN5 17 9 ISEN3.3 SW12 16 10 VFB3.3 VFB12 15 SDN3.3 11 SDN3.3 SGND 14 PGOOD 12 PGOOD SDWN 13 3.3V @ 5A + 5V-ALWAYS@ 50mA SDN5 12V @ 120mA + VFB12 SDWN Pin Assignments Top View VIN 3.3V-ALWAYS CPUMP3.3 HSD3.3 SW3.3 5V-ALWAYS LSD3.3 GND3.3 ISEN3.3 VFB3.3 SDN3.3 PGOOD 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 CPUMP5 HSD5 SW5 ISEN5 LSD5 GND5 VFB5 SDN5 SW12 VFB12 SGND SDWN Pin Description Pin Name 2 Pin Number Pin Function Description VIN 1 Input power. 3.3V-ALWAYS 2 3.3V Always on linear regulator. Load current on pins 2 and 6 must not exceed 50mA total. This pin should be decoupled to ground with a 10µF capacitor. CPUMP3.3 3 Charge Pump 3.3V. High side Gate drive voltage for 3.3V. This pin is to be connected to SW3.3 through a 100nF cap. and to 5V-ALWAYS through a diode HSD3.3 4 High-side gate driver for 3.3V. Connect this pin directly to the gate of an N-channel MOSFET. The trace from this pin to the MOSFET gate should be < 1". SW3.3 5 High side FET Source and Low Side FET Drain Switching Node. Switching node for 3.3V. 5V-ALWAYS 6 5V Always on linear regulator output. The sum of the load currents on pins 2 and 6 must not exceed 50mA total. This pin should be decoupled to ground with a 10µF capacitor. REV. 2.8.5 10/17/01 FAN5230 Pin Description (Continued) Pin Name Pin Number Pin Function Description LSD3.3 7 Low-side gate driver for 3.3V. Connect this pin directly to the gate of an N-channel MOSFET. The trace from this pin to the MOSFET gate should be < 1". GND3.3 8 Ground for 3.3V MOSFET. ISEN3.3 9 Current sense for 3.3V. This pin should be connected to the Drain of the bottom Mosfet with an appropriate resistor and an RC filter. See Application Section. VFB3.3 10 Voltage feedback for 3.3V. SDN3.3 11 Soft Start and ON/OFF for 3.3V. OFF=GND. ON=open with SDWN=High. Use open collector device for control. PGOOD 12 Power Good Flag. An open collector output that will be logic low if any output voltage is not above 89% of the nominal output voltage. SDWN 13 Master Shutdown. Shutdown for all power. Off when low. When high 5V/3.3V-ALWAYS are ON while 5V/3.3V-Main are ready to turn on if SDN5, SDN3.3 go open. SGND 14 Signal ground. VFB12 15 Voltage feedback for 12V. SW12 16 FET driver for 12V Boost. SDN5 17 Enable/Soft Start for 5V and 12V. Soft start and ON/OFF for 5V & 12V. OFF=Grounded. ON=open with SDWN=High. VFB5 18 Voltage feedback for 5V. GND5 19 Ground for 5V MOSFET. LSD5 20 Low side FET driver for 5V. Connect this pin directly to the gate of an N-channel MOSFET. The trace from this pin to the MOSFET gate should be < 1". ISEN5 21 Current Sense for 5V. This pin should be connected to the drain of the bottom Mosfet using appropriate resistor and RC filter. See Application Section. SW5 22 High Side Driver Source and Low Side Driver Drain Switching Node. Switching node for 5V. HSD5 23 High side FET driver for 5V. Connect this pin directly to the gate of an N-channel MOSFET. The trace from this pin to the MOSFET gate should be < 1". CPUMP5 24 Charge Pump 5V. High side Gate drive voltage for 5V. High side Gate drive voltage for 5V. This pin is to be connected to SW5 through a 100nF cap. and to 5V-ALWAYS through a diode. REV. 2.8.5 10/17/01 3 FAN5230 Absolute Maximum Ratings1 Parameter Conditions Min. Typ. Max. Units VIN -0.3 27 V SW, ISEN Pins,SDWN Pin -0.3 27 V CPUMP, HSD Pins -0.3 33 V SDN, VFB, V_always pins -0.3 6.5 V CPUMP to SW pins, and all other pins -0.3 6.5 V The sum of the load currents on pins 2 and 6 must not exceed 60mA total Note: 1. Stresses beyond "Absolute Maximum Ratings" may cause permanent device damage. Continuous exposure to absolute maximum rating conditions may affect device reliability. Functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specification is not implied. Recommended Operating Conditions Input Voltage, VIN +5.4V to 24V Ambient Temperature, TA -20°C to 85°C Thermal Information Thermal Resistance, RTHJA 88°C/W Thermal Resistance, RTHJC 28.5°C/W Maximum Junction Temperature 150°C Storage Temperature Range -65°C to 150°C Maximum Lead Temperature, Soldering 10 Sec 300°C ELECTRICAL SPECIFICATIONS Operating Conditions Recommended Operating Conditions Unless Noted Refers to Block Diagrams Parameter Conditions Min. VIN Input Supply Voltage (DC loading only) Note 1 5.4 Input Quiescent Current H/LSD Open Typ. Max. Units 24 V 1.4 3 mA Stand-by 300 400 µA Shut-down <1 5 µA 4.7 5.1 V Supply Input UVLO Threshold Rising Vbat 4.3 hysteresis 100 mV 5V and 3.3V Main Regulators Output Voltage Precision +2 % 300 345 kHz HSD On-Resistance, pull up 7 12 Ω HSD On Resistance pull down 4 10 Ω LSD On-Resistance, pull up 6 9 Ω LSD On Resistance pull down 5 8 Ω Oscillator Frequency, fosc 4 0.1 to 5.5A, 5.4 to 24V -2 255 REV. 2.8.5 10/17/01 FAN5230 Operating Conditions (Continued) Recommended Operating Conditions Unless Noted Refers to Block Diagrams Parameter Conditions Min. Typ. Max. Units HSD On Output, VCPUMP-VGS I = 10µA 100 mV HSD Off Output, VGS I = 10µA 100 mV LSD On Output, V5V-Always-VGS I = 10µA 100 mV LSD Off Output, VGS I = 10µA 100 mV Ramp Amplitude, pk-pk VIN = 16V 2 V Ramp Offset 0.5 V Ramp Gain from VIN 125 mV/V Error Amplifier GBW 3 MHz Current Limit Threshold R2, R8 = 1KΩ 90 135 180 µA Over Voltage Threshold 2µs delay 110 115 120 %VO Under Voltage Threshold 2µs delay 70 75 80 %VO (End of Soft Start) 4.2 SDN/SS Full On Voltage Min. V SDN/SS Full Off Voltage Max. 800 mV Max Duty Cycle 94 % Min PWM Time 200 nsec VFB3.3 Input Leakage Current 40 55 70 µA +2 % 12V Regulator Output Voltage Precision V_5 =4.9 to 5.1V and Io=0 to 150mA -2 2.472 VFB12 VFB12 Input Current Note 2 Oscillator Frequency (fosc/3) Gate Drive On-Resistance 85 High or Low V 100 200 nA 100 115 kHz 6 12 Ω 12V Regulator (Continued) On Output, V5V-Always-VGS I = 10µA 100 mV Off Output, VGS I = 10µA 100 mV Ramp Amplitude, pk-pk 2 V Error Amplifier GBW 1 MHz Under Voltage Shut Down 2µs delay Over Voltage Shut Down Measured at VFB12 Min Duty Cycle Max Duty Cycle 70 76 80 115 %VO 0 (By design) 32 %VO % 33 34 % 1.3 1.5 Ω 2 % 50 mA 5V and 3.3V Always Bypass Switch rdson Linear Regulator Accuracy 5.6 to 24V, 0 to 50mA, 5V Main On or Off -3.3 I3.3 + I5 0 Over-current Limit 2µs delay 100 180 Under-voltage Threshold 2µs delay 70 75 0-70°C -1 Rated Output Current mA 80 % 1 % Reference Internal Reference Accuracy REV. 2.8.5 10/17/01 5 FAN5230 Operating Conditions (Continued) Recommended Operating Conditions Unless Noted Refers to Block Diagrams Parameter Conditions Min. Typ. Max. Units 800 mV Control Functions SDWN Off Voltage Max. SDWN On Voltage Min. 3 V Over-temperature Shutdown, tj 150 °C Over-temperature Hysteresis 25 °C PGOOD Threshold PWM Buck Converters PGOOD Sink Current -14 -11 -8.5 -4 %VO1 mA PGOOD leakage 1 µA +5V Analog Softstart Css=100nF 65 msec +3.3V Analog Softstart Css=100nF 65 msec 5 µA 10 µs Soft Start Current PGOOD Min Pulse Width Note 2 5 Notes 1. The minimum input voltage does not include voltage drop in the source supply due to source resistance. It is operating voltage for static load conditions. To get acceptable load transient performance, the input voltage required will be much higher, in the 7.5 to 8.5 volt range or even higher depending on the severity of dynamic load, source impedance and input and output capacitance and inductor values. The user should thoroughly test the performance at minimum input voltage using intended component values and transient loading. 2. Min/Max specifications are guaranteed by design. 6 REV. 2.8.5 10/17/01 REV. 2.8.5 10/17/01 ISEN VFB – – + + LSD VREF – LSD REF CURRENT SENSE AMP DUTY CYCLE CLAMP – + PWM/HYST LO PWM GATE LOGIC HYST HI SET D Q CLR L Q CLK VCC OC DETECT RAMP PWM MODE CONTROL + – PWM LATCH SUM – + VCC FAN5230 5V/3.3V Switcher ADAPTIVE GATE CONTROL HSD PGND LSD ISEN PHASE Figure 1. FAN5230 5V/3.3V Internal Block Diagram of PWM/PFM Loops. + – ERROR AMP HYSTERIC COMPARATOR + CLK CPUMP VIN 5V L1 CL VFB VOUT FAN5230 7 FAN5230 FAN5230 12V Converter CK:3 CK :3 Ve Ramp PWM +5 VREF=2.5V R CLK:3 (30%DC, 100kHz) Ramp SW12 V out 16R Vout + – – + Q R Q PWM Ve VFB12 S CLK:3 DISABLE Figure 2. FAN5230 12V Internal Block Diagram VIN FAN5230 5V/3.3V-ALWAYS LDO 3.3V ALWAYS LDO 5V ALWAYS VFB5 Figure 3. FAN5230 5V/3.3V—ALWAYS Internal Block Diagram 8 REV. 2.8.5 10/17/01 FAN5230 Functional Description The FAN5230 is a high efficiency and high precision DC/DC controller for notebook and other portable applications. It provides all of the voltages necessary for system electronics: 5V, 3.3V, 12V, and both 3.3V-ALWAYS and 5V-ALWAYS. Utilization of both input and output voltage feedback in a current-mode control allows for fast loop response over a wide range of input and output variations. Current sense based on MOSFET RDS,on gives maximum efficiency, while also permitting the use of a sense resistor for high accuracy. 3.3V and 5V Architecture The 3.3V and 5V switching regulator outputs of the FAN5230 are generated from the unregulated input voltage using synchronous buck converters. Both high side and lowside MOSFETs are N-channel. The 3.3V and 5V switchers have pins for current sensing and for setting of output over-current threshold using MOSFET RDS,on. Each converter has a pin for voltage-sense feedback, a pin that shuts down the converter, and a pin for generating the boost voltage to drive the high-side MOSFET. If the 5V switcher is not used, connect SDN5 (pin 17) to SGND (pin 14). If the 3.3V switcher is not used, connect SDN3.3 (pin 11) to SGND (pin 14). The following discussion of the FAN5230 design will be done with reference to Figures 1 through 4, showing the internal block diagram of the IC. 3.3V and 5V PWM Current Sensing Peak current sensing is done on the low side driver because of the very low duty-cycle on the high side MOSFET. The current is sampled 50ns after turn on and the value is held for current feedback and over-current limit. 3.3V and 5V PWM Loop Compensation The 3.3V and 5V control loops of the FAN5230 function as voltage mode with current feedback for stability. They each have an independent voltage feedback pin, as shown in Figure 1. They use voltage feed-forward to guarantee loop rejection of input voltage variation: that is to say that the PWM (pulse width modulation) ramp amplitude is varied as a function of the input voltage. Compensation of the control loops is done entirely internally using current-mode feedback compensation. This scheme allows the bandwidth and phase margin to be almost independent of output capacitance and ESR. 3.3V and 5V PWM Current Limit The 3.3V and 5V converters each sense the voltage across their own low-side MOSFET to determine whether to enter current limit. If an output current in excess of the current limit threshold is measured then the converter enters a pulse skipping mode where Iout is equal to the over-current (OC) set limit. After 8 clock cycles then the regulator is latched off REV. 2.8.5 10/17/01 (HSD and LSD off). This is the likely scenario in the case of a "soft" short. If the short is "hard" it will instantly trigger the under-voltage protection which again will latch the regulator off (HSD and LSD off) after a 2µs delay. Selection of a current-limit set resistor must include the tolerance of the current-limit trip point, the MOSFET on resistance and temperature coefficient, and the ripple current, in addition to the maximum output current. Example: Maximum DC output current on the 5V is 5A, the MOSFET RDS,on is 17mΩ, and the inductor is 5µH at a current of 5A. Because of the low RDS,on, the low-side MOSFET will have a maximum temperature (ambient + self-heating) of only 75°C, at which its RDS,on increases to 20mΩ. Peak current is DC output current plus peak ripple current: Ipk ≈ Idc + TV0 2L = 5A + 4µsec • 5V = 7A 2 • 5µH where T is the maximum period, VO is output voltage, and L is the inductance. This current generates a voltage on the low-side MOSFET of 7A • 20mΩ = 140mV. The current limit threshold is typically 150mV (worst-case 135mV) with R2 = 1KΩ, and so this value is suitable. R2 could be increased a further 10% if additional noise margin is deemed necessary. Precision Current Limit Precision current limiting can be achieved by placing a discrete sense resistor between the source of the low-side MOSFET and ground. In this case, current limit accuracy is set by the tolerance of the IC, +10%. HSD SW LSD ISEN GND Figure 4. Using a Precision Current Sense Resistor Shutdown (SDWN) The SDWN pin turns off all 5 converters (+5V, +3.3V, and +12V, 5V/3.3V-ALWAYS) and puts the FAN5230 into a lowpower mode (Shutdown mode). 9 FAN5230 This mode of operation implies the use of a push button switch between SDWN and Vin. Pushing the button allows (for the duration of the contact) to power the 3.3V-ALWAYS and 5V-ALWAYS long enough for the uC to power up and in turn latch the SDWN pin high. As the load current becomes very light, the FAN5230 begins pulse skipping, but remains synchronized with the clock. See next section for low side drive management. Low Side Driver Forcing in Light Load Stand-by mode is defined as the condition by which V-Mains are OFF and V-ALWAYS are ON (SDWN=1 and SDN3.3=SDN5=0). During light load operation, the Low Side Driver (LSD) is traditionally turned permanently OFF to avoid current inversion in the inductor and associated efficiency losses. At the same time the low side driver also needs to be turned ON in order to a) measure current (current is sensed on the low side driver) and b) assure proper operation of the charge pump, especially under low current and low input voltage conditions. In order to accomplish all the above, when the circuit enters hysteretic operation the LSD is kept “ON” to re-circulate positive and decaying currents (corresponding to negative drops across low side driver Rdson) and turned off as soon as current crosses zero (corresponding to drop across Rdson becoming positive). This way the low side driver is utilized in “partial duty” or as “active zero drop diode” (compared to classic light load operation in which the LSD is turned permanently OFF) allowing more functionality without loss in efficiency. ALWAYS mode of Operation 3.3V Voltage Adjustment If it is desired that 5V-ALWAYS and 3.3V-ALWAYS are always ON then the SDWN pin must be connected to Vin permanently. This way the two ALWAYS regulators come up as soon as there is power while the state of the Main regulators can be controlled via the SDN5 and SDN3.3 pins. The output voltage of the 3.3V converter can be increased by as much as 10% by inserting a resistor divider in the feedback line. The feedback pin impedance is about 66KΩ. Thus, for example, to increase the output of the 3.3V converter by 10%, use a 2.21KΩ/33.2KΩ divider. Sequencing Table Note that the output of the 5V regulator cannot be adjusted. The feedback line of the 5V regulator is used internally as a 5V supply and, therefore, cannot tolerate any impedance in series with it. Once the SDWN is high then the ALWAYS voltages are enabled to go high if the respective SDN3.3 and SDN5 go high. MAIN 3.3V and 5V Softstart, Sequencing and Stand-by Softstart of the 3.3V and 5V converters is accomplished by means of an external capacitor between pins SDN3.3 (SDN5) and ground. The 3.3V (5V) main converter is turned ON if SDWN and SDN3.3 (SDN5) are both high and is turned off if either SDWN or SDN3.3 (SDN5) is low. SDN5 X 0 1 0 1 3V&5V SDN3.3 SDWN ALWAYS X 0 0 0 1 1 0 1 1 1 1 1 1 1 1 5V MAIN 0 0 1 0 1 3.3V MAIN 0 0 0 1 1 3.3V and 5V Light Load Mode The 3.3V and 5V converters are synchronous bucks, and can operate in two quadrants, this means that the ripple current is constant and independent of the load current. At light loads, this ripple current translates into poor efficiency, since it causes circulating current losses in the MOSFETs. To optimize the efficiency at light loads, then, the FAN5230 switches from normal operation to a special light load mode after an 8 clock pulse delay. This prevents false triggering when the voltage across the on-state low-side MOSFET goes positive. Vice-versa when this voltage becomes negative the FAN5230 switches back to PWM operation. The current threshold for switch to and from light load is therefore: Ith = Iripplepeak In light load mode, the FAN5230 switches from PWM (pulse width modulation) to PFM (pulse frequency modulation), which reduces the gate drive current. 10 3.3V and 5V Main Overvoltage Protection (Soft Crowbar) When the output voltage of the 3.3V (or the 5V) converter exceeds approximately 115% of nominal, the converter enters the over-voltage (OV) protection mode, with the goal of protecting the load from damage. During operation, severe load dump or a short of an upper MOSFET could cause the output voltage to increase significantly over normal operation range without circuit protection. When the output exceeds the overvoltage threshold, the over-voltage comparator forces the lower gate driver high and turns the lower MOSFET on. This will pull down the output voltage and eventually may blow the battery fuse. As soon as output voltage drops below the threshold, OVP comparator is disengaged. The OVP scheme also provides a soft crowbar function (bang-bang control followed by blow of the fuse) which helps to tackle severe load transients but does not invert output voltage when activated—a common problem for OVP schemes with a latch. The prevention of output inversion eliminates the need for a Schottky diode across the load. REV. 2.8.5 10/17/01 FAN5230 3.3V and 5V Under-voltage Protection 5V/3.3V-ALWAYS Operation When the output voltage of either the 3.3V or 5V falls below 75% of the nominal value, both converters, go into under-voltage (UV) protection, after a 2µsec delay. In undervoltage protection, the high and low side MOSFETs are turned off. Once under-voltage protection is triggered, it remains on until power is recycled or the SDWN pin is reset. The 5V-ALWAYS supply is generated from either the on-chip linear regulator or through an internal switch from the VFB pin of the 5V switching supply. The 5V-ALWAYS supply should be decoupled to ground with a 10µF capacitor. 12V Architecture The 12V converter is a traditional non-isolated fly-back (also known as a "boost" converter). The converter’s input voltage is the +5V switcher output, so that +12V can only be present if +5V is present. Also, if the external MOSFET is off, the output of the +12V converter is +5V, not zero. This in turn will provide non-zero output for the 12V regulator. For complete turn-off of the 12V regulator an external P-channel MOSFET or an LDO regulator with on/off control may be used. If an LDO is used for 12V then the boost converter should be set to 13.2V using the external resistor divider network. If the 12V “boost” converter is not used, connect VFB12 (pin 15) to 5V-ALWAYS (pin 6). 12V Loop Compensation The 12V converter should be run in discontinuous conduction mode. In this mode, the converter will be stable if a capacitor with suitable ESR value is selected. A 68uF tantalum with 500mA ripple current rating and 95mΩ is recommended here. 12V Protection The 12V converter is protected against overvoltage. If the 12V feedback is more than 10–15% above the nominal set voltage, a comparator forces the MOSFET off until the voltage falls below the comparator threshold. The 12V converter is also protected against over-current. If a short circuit pulls the output below 9V, all of the switching converters go into UV protection, after a 2µs delay. In UV protection, all MOSFETs are turned off. Once UV protection is triggered, it remains on until the input power is recycled or the SDWN is reset. When the 5V switching supply is off, or if its output voltage is not within tolerance, the 5V-ALWAYS switch is open, and the linear regulator is on. When the 5V switching supply is running and has an output voltage within specification, the linear regulator is off, and the switch is on. The switch has sufficiently low resistance that at maximum current draw on the 5V-ALWAYS supply, the output voltage is regulated within specifications. The 3.3V-ALWAYS is generated from a linear regulator attached internally to the 5V-ALWAYS. The 3.3V-ALWAYS supply should be decoupled to ground with a 10µF capacitor. The purpose of the two ALWAYS supplies (combined current is specified to never exceed 50mA) is to provide power to the system micro-controller (8051 class) as well as other IC’s needing a stand-by power. The micro-controller as well as the other IC’s could be operated from either 5V or 3.3V ALWAYS, so the FAN5230 provides both. 5V/3.3V-ALWAYS Protections The two internal linear regulators are current limited and under-voltage protected. Once protection is triggered all outputs are turned off until power is cycled or the SDWN is reset. Power good Power good is asserted when both PWM Buck converters are above specified threshold. No other regulators are monitored by Power good. When PGOOD goes low it will stay low for at least 10µsec (Tw). See fig. 5. Vmain Vth 12V Softstart and Sequencing The 12V output is started at the same time as the 5V output. The softly rising 5V output automatically generates a softly rising 12V output. The duty cycle of the 12V PWM is limited to prevent excessive current draw. t PGOOD The 12V supply must build up a voltage higher than the UVLO limit (9V) by the time the 5V is above its UVLO (3.75V) in order to avoid triggering of UV protection during soft start. t Tw Figure 5. PGOOD Timing Diagram REV. 2.8.5 10/17/01 11 FAN5230 Error Amplifier output voltage clamp Input UVLO During a load transient the error amplifier voltage is allowed full swing. After two clock cycles, if the amplifier is still out of range the voltage and consequently the duty cycle (DC) is clamped. The DC clamp automatically limits the build up of over-currents during abnormal conditions, including short circuits: If the input voltage falls below the UVLO threshold, the FAN5230 turns itself off and stays off as long as Input voltage is below threshold. VFB=0.5V+Vo/8 VRAMP =0.5V+Vin/8 VREF – + Vclamp=0.5V+ +Vo/8 +/-0.2V 0.4V 2 Cycles Counter LSD Buck LDO OFF-LATCH OFF-LATCH OC/UV (LDO) – EA + HSD Buck OC/UV (Bucks) + – IC Protections Table LSD Boost ON OFF-LATCH " " OFF-LATCH " OV (Buck)* OFF SOFT CROWBAR ON ON OV (Boost) ON ON ON OFF SDWN=0 OFF OFF OFF OFF OT OFF OFF OFF OFF ON OFF-LATCH ON 33% DC UV (Boost) OFF-LATCH OFF-LATCH OC (Boost) ON ON * Only the converter in Over-Voltage goes in SOFT CROWBAR mode. Figure 6. Duty-Cycle Clamp Thermal shutdown If the die temperature of the FAN5230 exceeds safe limits, the IC shuts itself off. When the over-temperature (OT) event ends, the IC comes back to normal operation. There is a 25°C thermal hysteresis between shutdown and start up. Generic Mobile System Block Diagram Vin=5.6 to 24V 5V SDN5 3.3V Vcpu SDN3.3 RC5230 µC 8051 5V-Always PGOOD RC5231 1.5V CPU 2.5V µC µP Clock PGOOD 3.3V-Always CPU PGOOD EN SDWN SDWN µP CODE EXECUTION RESET LOGIC Figure 7. System Block Diagram 12 REV. 2.8.5 10/17/01 FAN5230 Notebook Application Circuit 5.4-24V C1 Pin 6 C2 3.3V@50mA C10 5V@50mA C11 3.3V@5A D5 L1 C5 Q1 + C12, C13 D1 Q2 R2 SDN3.3 C3 +5V D4 1 2 3 4 5 6 7 8 9 10 11 12 U1 FAN5230 24 23 22 21 20 19 18 17 16 15 14 13 L2 C6 Q3 C7 C8 + D2 5V@5A R3 L3 Q4 SDN5 D3 12V@120mA R6 Q5 SDWN C9 R4 R5 C4 R1 PGOOD Figure 8. FAN5230 Notebook Application Circuit Table 1. FAN5230 Application Bill of Materials Reference Manufacturer, Part # C1 SANYO 25SP33M Quantity 1 Description Comments 33µF, 25V OSCON, Irms = 3A, 19V adapter. C2-6 Any 5 100nF, 50V Ceramic C7-8 C12-13 KEMET T510X337(1)010AS 2 2 330µF, 10V Tantalum, ESR=35mΩ C10-11 AVXTPSA106010#1800 2 10µF, 10V Tantalum, ESR=1.8Ω C9 AVX TPSV68*025R0095 1 68µF, 25V, ESR=95mΩ Tantalum, Irms = 0.5A R1 Any 1 10KΩ, 1% R2, R3 Any 2 1KΩ, 1% R4, R5 Any 1 380KΩ, 100KΩ R6 Any 1 10Ω D1-3 Fairchild SS22 3 2A, 40V Schottky D4-5 Fairchild MBR0520L 2 500mA, 20V Schottky L1-2 Any 2 6.4µH, 5A L3 Any 1 5.6µH, 2A 1% R < 25mΩ Q1-4 Fairchild FDS6690A 4 30V N-channel MOSFET R = 17mΩ Q5 Fairchild NDC631N 1 20V N-channel MOSFET R = 60mΩ U1 Fairchild FAN5230 1 SER Controller REV. 2.8.5 10/17/01 13 FAN5230 MOSFET Selection 3.3V and 5V Schottky Selection The notebook application circuit shown in Figure 1 is designed to run with an input voltage operating range of 5.4-24V. This wide input range helps determine the selection of the MOSFETs for the 3.3V and 5V converters, since the high-side MOSFET is on (Vout / Vin) of the time, and the low-side MOSFET 1 – (Vout / Vin) of the time. The maxima and minima are tabulated in Table 2: The maximum current at which the converters operate in PFM mode determines selection of a Schottky. In the application shown in Figure 8, since the transition can occur at a current as high as 28mV * (17.5KΩ / 10KΩ) / 35mΩ = 1.4A, the diode (with 24V input) will be conducting 86% of the period (from Table 2). It thus has an average current of 1.4A * 0.86 = 1.2A, which requires a Schottky current rating >1A. Table 2. MOSFET Duty Cycles 3.3V and 5V Inductor Selection See Table 1. High-side FET 3.3V and 5V Output Cap Selection Vin Vout 5.4V 24V 3.3V .61 .14 5V .43 .21 See Table 1. 12V Component Selection Calculation of the inductor, diode and output capacitor for the +12V output fly-back is complex, depending on output power and efficiency. See Applications Bulletin AB-19 for an Excel spreadsheet calculation tool. See Table 1 also. Low-side FET Vin Vout 5.4V 24V 3.3V .34 .86 5V .07 .79 Input Capacitor Selection Input capacitor selection is determined by ripple current rating. With two converters operating in parallel at differing duty cycles, calculation of input ripple current is complex; see Applications Bulletin AB-19 for an Excel spreadsheet calculation tool. All four MOSFETs have maximum duty cycles greater than 50%. Thus, it is necessary to size all four approximately the same. Efficiency 100 90 80 Efficiency (%) 70 60 50 40 30 20 10 0 1 10 100 1,000 10,000 Load Current mA PWM 14 Hyst REV. 2.8.5 10/17/01 FAN5230 Mechanical Dimensions QSOP 24-Lead Inches Symbol Min. A A1 A2 b c D E e H L N α ccc Millimeters Max. Min. 1.35 1.75 0.1 0.25 1.37 1.57 0.20 0.30 0.19 0.25 8.55 8.74 3.81 3.99 0.635 BSC 0.228 0.016 5.79 0.40 24 1. Dimensioning and tolerancing per ANSI Y14.5M-1982. Max. 0.0532 0.0668 0.0040 0.0098 0.054 0.062 0.008 0.012 0.0075 0.0098 0.337 0.344 0.150 0.157 0.025 BSC 0.244 0.050 Notes: Notes 2. "D" and "E" do not include mold flash. Mold flash or protrusions shall not exceed .006 inch (0.15mm). 3. "L" is the length of terminal for soldering to a substrate. 4. Terminal numbers are shown for reference only. 5 5 24 0° 8° 0° 8° .004 — 0.10 6. Symbol "N" is the maximum number of terminals. 2, 4 2 6.20 1.27 — 5. "b" and "c" dimensions include solder finish thickness. 3 6 D E A H C A1 A2 B e SEATING PLANE –C– α L LEAD COPLANARITY ccc C REV. 2.8.5 10/17/01 15 FAN5230 Ordering Information Product Number FAN5230QSC Package 24 Lead QSOP DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com 10/17/01 0.0m 002 Stock#DS30005230 2001 Fairchild Semiconductor Corporation