L79LxxAB L79LxxAC - L79LxxC Negative voltage regulators Features ■ Output current up to 100 mA ■ Output voltages of -5; -6; -8; -9; -12; -15V ■ Thermal overload protection ■ Short circuit protection ■ No external components are required ■ Available in either ±5% (AC) or ±10% (C) selection TO-92 Description SO-8 The L79Lxx series of three-terminal negative regulators employ internal current limiting and thermal shutdown, making them essentially indestructible. If adequate heat-sink is provided, they can deliver up to 100 mA output current. power pass elements to make high-current voltage regulators. They are intended as fixed voltage regulators in a wide range of applications including local or oncard regulation for elimination of noise and distribution problems associated with single-point regulation. In addition, they can be used with Table 1. SOT-89 The L79Lxx series used as Zener diode/resistor combination replacement, offers an effective output impedance improvement of typically two orders of magnitude, along with lower quiescent current and lower noise. Device summary Part number L79L05AC L79L09AC L79L05AB L79L09AB L79L06C L79L12C L79L06AC L79L12AC L79L06AB L79L12AB L79L08C L79L15C L79L08AC L79L15AC L79L08AB L79L15AB L79L09C December 2007 Rev 14 1/22 www.st.com 22 L79LxxAB - L79LxxAC - L79LxxC Contents 1 Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 6 Order codes 7 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 2/22 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 L79LxxAB - L79LxxAC - L79LxxC 1 Diagram Figure 1. Schematic diagram Diagram 3/22 Pin configuration L79LxxAB - L79LxxAC - L79LxxC 2 Pin configuration Figure 2. Pin connection (top view, bottom view for TO-92) PIN 1 = GND PIN 2 = VIN PIN 3 = VOUT SO-8 Figure 3. 4/22 Test circuit SOT-89 TO-92 L79LxxAB - L79LxxAC - L79LxxC Maximum ratings 3 Maximum ratings Table 2. Absolute maximum ratings Symbol Parameter VI DC input voltage IO Output current PD Value VO = -5 to -9 V -30 VO = -12 to -15 V -35 Unit V 100 Power dissipation TSTG Storage temperature range TOP Operating junction temperature range mA Internally Limited -40 to 150 For L79L00C, L79L00AC (1) mW °C 0 to 125 °C For L79L00AB -40 to 125 1. Our SO-8 package used for Voltage Regulators is modified internally to have pins 2, 3, 6 and 7 electrically communed to the die attach flag. This particular frame decreases the total thermal resistance of the package and increases its ability to dissipate power when an appropriate area of copper on the printed circuit board is available for heat-sinking. The external dimensions are the same as for the standard SO-8. Table 3. Thermal data Symbol RthJC RthJA 1. Parameter Thermal resistance junction-case. (Max) Thermal resistance junction-ambient. (Max) SO-8 TO-92 20 55 (1) 200 SOT-89 Unit 15 °C/W °C/W 2 Considering 6 cm of copper Board heat-sink. 5/22 Electrical characteristics L79LxxAB - L79LxxAC - L79LxxC 4 Electrical characteristics Table 4. Electrical characteristics of L79L05 (refer to the test circuits, TJ = 0 to 125 °C, VI = -10 V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF unless otherwise specified) Symbol Parameter VO Output voltage VO Output voltage ΔVO Line regulation ΔVO Load regulation Id Quiescent current Test conditions Min. Typ. Max. Unit TJ = 25°C -4.6 -5 -5.4 V IO = 1 to 40 mA, VI = -7 to -20 V -4.5 -5.5 IO = 1 to 70 mA, VI = -10 V -4.5 -5.5 VI = -7 to -20 V, TJ = 25°C 200 VI = -8 to -20 V, TJ = 25°C 150 IO = 1 to 100 mA, TJ = 25°C 60 IO = 1 to 40 mA, TJ = 25°C 30 TJ = 25°C 6 mA TJ = 125°C 5.5 mA IO = 1 to 40 mA 0.2 VI = -8 to -20 V 1.5 ΔId Quiescent current change eN Output noise voltage B =10Hz to 100kHz, TJ = 25°C Supply voltage rejection VI = -8 to -18V, f = 120Hz IO = 40 mA, TJ = 25°C SVR Vd 6/22 Dropout voltage V mV mV mA 40 40 µV 49 dB 1.7 V L79LxxAB - L79LxxAC - L79LxxC Table 5. Symbol Electrical characteristics of L79L06 (refer to the test circuits, TJ = 0 to 125 °C, VI = -12 V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF unless otherwise specified) Parameter VO Output voltage VO Output voltage ΔVO Line regulation ΔVO Load regulation Id Electrical characteristics Quiescent current Test conditions Min. Typ. Max. Unit TJ = 25°C -5.52 -6 -6.48 V IO = 1 to 40 mA, VI = -8.5 to -20 V -5.4 -6.6 IO = 1 to 70 mA, VI = -12 V -5.4 -6.6 VI = -8.5 to -20 V, TJ = 25°C 200 VI = -9 to -20 V, TJ = 25°C 150 IO = 1 to 100 mA, TJ = 25°C 60 IO = 1 to 40 mA, TJ = 25°C 30 TJ = 25°C 6 mA TJ = 125°C 5.5 mA IO = 1 to 40 mA 0.2 VI = -8 to -20 V 1.5 ΔId Quiescent current change eN Output noise voltage B =10Hz to 100kHz, TJ = 25°C Supply voltage rejection VI = -9 to -20V, f = 120Hz IO = 40 mA, TJ = 25°C SVR Vd Table 6. Symbol Parameter VO Output voltage ΔVO Line regulation ΔVO Load regulation Quiescent current Test conditions mA 38 50 µV 46 dB 1.7 V Min. Typ. Max. Unit TJ = 25°C -7.36 -8 -8.64 V IO = 1 to 40 mA, VI = -10.5 to -23 V -7.2 -8.8 IO = 1 to 70 mA, VI = -14 V -7.2 -8.8 200 VI = -11 to -23 V, TJ = 25°C 150 IO = 1 to 100 mA, TJ = 25°C 80 IO = 1 to 40 mA, TJ = 25°C 40 TJ = 25°C 6 mA TJ = 125°C 5.5 mA IO = 1 to 40 mA 0.2 VI = -11 to -23 V 1.5 Quiescent current change eN Output noise voltage B =10Hz to 100kHz, TJ = 25°C Supply voltage rejection VI = -12 to -23V, f = 120Hz IO = 40 mA, TJ = 25°C Dropout voltage V VI = -10.5 to -23 V, TJ = 25°C ΔId Vd mV Electrical characteristics of L79L08 (refer to the test circuits, TJ = 0 to 125 °C, VI = -14 V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF unless otherwise specified) Output voltage SVR mV Dropout voltage VO Id V mV mV mA 36 60 µV 45 dB 1.7 V 7/22 Electrical characteristics Table 7. Symbol Electrical characteristics of L79L09 (refer to the test circuits, TJ = 0 to 125 °C, VI = -15 V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF unless otherwise specified) Parameter VO Output voltage VO Output voltage ΔVO Line regulation ΔVO Load regulation Id L79LxxAB - L79LxxAC - L79LxxC Quiescent current Test conditions Min. Typ. Max. Unit TJ = 25°C -8.28 -9 -9.72 V IO = 1 to 40 mA, VI = -11.5 to -23 V -8.1 -9.9 IO = 1 to 70 mA, VI = -15 V -8.1 -9.9 VI = -11.5 to -23 V, TJ = 25°C 250 VI = -12 to -23 V, TJ = 25°C 200 IO = 1 to 100 mA, TJ = 25°C 80 IO = 1 to 40 mA, TJ = 25°C 40 TJ = 25°C 6 mA TJ = 125°C 5.5 mA IO = 1 to 40 mA 0.2 VI = -12 to -23 V 1.5 ΔId Quiescent current change eN Output noise voltage B =10Hz to 100kHz, TJ = 25°C Supply voltage rejection VI = -12 to -23V, f = 120Hz IO = 40 mA, TJ = 25°C SVR Vd Table 8. Symbol Parameter VO Output voltage ΔVO Line regulation ΔVO Load regulation Quiescent current Test conditions 36 70 µV 44 dB 1.7 V Typ. Max. Unit TJ = 25°C -11.1 -12 -12.9 V IO = 1 to 40 mA, VI = -14.5 to -27 V -10.8 -13.2 IO = 1 to 70 mA, VI = -19 V -10.8 -13.2 250 VI = -16 to -27 V, TJ = 25°C 200 IO = 1 to 100 mA, TJ = 25°C 100 IO = 1 to 40 mA, TJ = 25°C 50 TJ = 25°C 6.5 mA TJ = 125°C 6 mA mV mV IO = 1 to 40 mA 0.2 VI = -16 to -27 V 1.5 eN Output noise voltage B =10Hz to 100kHz, TJ = 25°C Supply voltage rejection VI = -15 to -25V, f = 120Hz IO = 40 mA, TJ = 25°C Dropout voltage V VI = -14.5 to -27 V, TJ = 25°C Quiescent current change 8/22 mA Min. ΔId Vd mV Electrical characteristics of L79L12 (refer to the test circuits, TJ = 0 to 125 °C, VI = - 19 V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF unless otherwise specified) Output voltage SVR mV Dropout voltage VO Id V mA 36 80 µV 42 dB 1.7 V L79LxxAB - L79LxxAC - L79LxxC Table 9. Symbol Electrical characteristics of L79L15 (refer to the test circuits, TJ = 0 to 125 °C, VI = - 23 V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF unless otherwise specified) Parameter VO Output voltage VO Output voltage ΔVO Line regulation ΔVO Load regulation Id Electrical characteristics Quiescent current Test conditions Min. Typ. Max. Unit TJ = 25°C -13.8 -15 -16.2 V IO = 1 to 40 mA, VI = -17.5 to -30 V -13.5 -16.5 IO = 1 to 70 mA, VI = -23 V -13.5 -16.5 VI = -17.5 to -30 V, TJ = 25°C 300 VI = -20 to -30 V, TJ = 25°C 250 IO = 1 to 100 mA, TJ = 25°C 150 IO = 1 to 40 mA, TJ = 25°C 75 TJ = 25°C 6.5 mA TJ = 125°C 6 mA VI = -20 to -30 V 1.5 eN Output noise voltage B =10Hz to 100kHz, TJ = 25°C Supply voltage rejection VI = -18.5 to -28.5.V, f = 120Hz IO = 40 mA, TJ = 25°C Table 10. Symbol Parameter VO Output voltage ΔVO Line regulation ΔVO Load regulation Quiescent current Test conditions µV 39 dB 1.7 V Min. Typ. Max. Unit TJ = 25°C -4.8 -5 -5.2 V IO = 1 to 40 mA, VI = -7 to -20 V -4.75 -5.25 IO = 1 to 70 mA, VI = -10 V -4.75 -5.25 150 VI = -8 to -20 V, TJ = 25°C 100 IO = 1 to 100 mA, TJ = 25°C 60 IO = 1 to 40 mA, TJ = 25°C 30 TJ = 25°C 6 mA TJ = 125°C 5.5 mA IO = 1 to 40 mA 0.1 VI = -8 to -20 V 1.5 Quiescent current change eN Output noise voltage B =10Hz to 100kHz, TJ = 25°C Supply voltage rejection VI = -8 to -18V, f = 120Hz IO = 40 mA, TJ = 25°C Dropout voltage V VI = -7 to -20 V, TJ = 25°C ΔId Vd 33 90 Electrical characteristics of L79L05AB and L79L05AC (refer to the test circuits, VI = - 10 V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF, TJ = 0 to 125 °C for L79L05AC, TJ = -40 to 125 °C for L79L05AB, unless otherwise specified) Output voltage SVR mA Dropout voltage VO Id mV 0.2 Quiescent current change Vd mV IO = 1 to 40 mA ΔId SVR V mV mV mA 41 40 µV 49 dB 1.7 V 9/22 Electrical characteristics Table 11. Symbol Electrical characteristics of L79L06AB and L79L06AC (refer to the test circuits, VI = - 12 V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF, TJ = 0 to 125 °C for L79L05AC, TJ = -40 to 125 °C for L79L05AB, unless otherwise specified) Parameter VO Output voltage VO Output voltage ΔVO Line regulation ΔVO Load regulation Id L79LxxAB - L79LxxAC - L79LxxC Quiescent current Test conditions Min. Typ. Max. Unit TJ = 25°C -5.76 -6 -6.24 V IO = 1 to 40 mA, VI = -8.5 to -20 V -5.7 -6.3 IO = 1 to 70 mA, VI = -12 V -5.7 -6.3 VI = -8.5 to -20 V, TJ = 25°C 150 VI = -9 to -20 V, TJ = 25°C 100 IO = 1 to 100 mA, TJ = 25°C 60 IO = 1 to 40 mA, TJ = 25°C 30 TJ = 25°C 6 mA TJ = 125°C 5.5 mA IO = 1 to 40 mA 0.1 VI = -8 to -20 V 1.5 ΔId Quiescent current change eN Output noise voltage B =10Hz to 100kHz, TJ = 25°C Supply voltage rejection VI = -9 to -20V, f = 120Hz IO = 40 mA, TJ = 25°C SVR Vd Table 12. Symbol Parameter VO Output voltage ΔVO Line regulation ΔVO Load regulation Quiescent current Test conditions 39 50 µV 46 dB 1.7 V Typ. Max. Unit TJ = 25°C -7.68 -8 -8.32 V IO = 1 to 40 mA, VI = -10.5 to -23 V -7.6 -8.4 IO = 1 to 70 mA, VI = -14 V -7.6 -8.4 175 VI = -11 to -23 V, TJ = 25°C 125 IO = 1 to 100 mA, TJ = 25°C 80 IO = 1 to 40 mA, TJ = 25°C 40 TJ = 25°C 6 mA TJ = 125°C 5.5 mA IO = 1 to 40 mA 0.1 VI = -11 to -23 V 1.5 eN Output noise voltage B =10Hz to 100kHz, TJ = 25°C Supply voltage rejection VI = -12 to -23V, f = 120Hz IO = 40 mA, TJ = 25°C Dropout voltage V VI = -10.5 to -23 V, TJ = 25°C Quiescent current change 10/22 mA Min. ΔId Vd mV Electrical characteristics of L79L08AB and L79L08AC (refer to the test circuits, VI = - 14 V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF, TJ = 0 to 125 °C for L79L05AC, TJ = -40 to 125 °C for L79L05AB, unless otherwise specified) Output voltage SVR mV Dropout voltage VO Id V mV mV mA 37 60 µV 45 dB 1.7 V L79LxxAB - L79LxxAC - L79LxxC Table 13. Symbol Electrical characteristics of L79L09AB and L79L09AC (refer to the test circuits, VI = - 15 V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF, TJ = 0 to 125 °C for L79L05AC, TJ = -40 to 125 °C for L79L05AB, unless otherwise specified) Parameter VO Output voltage VO Output voltage ΔVO Line regulation ΔVO Load regulation Id Electrical characteristics Quiescent current Test conditions Min. Typ. Max. Unit TJ = 25°C -8.64 -9 -9.36 V IO = 1 to 40 mA, VI = -11.5 to -23 V -8.55 -9.45 IO = 1 to 70 mA, VI = -15 V -8.55 -9.45 VI = -11.5 to -23 V, TJ = 25°C 225 VI = -12 to -23 V, TJ = 25°C 150 IO = 1 to 100 mA, TJ = 25°C 80 IO = 1 to 40 mA, TJ = 25°C 40 TJ = 25°C 6 mA TJ = 125°C 5.5 mA IO = 1 to 40 mA 0.1 VI = -12 to -23 V 1.5 ΔId Quiescent current change eN Output noise voltage B =10Hz to 100kHz, TJ = 25°C Supply voltage rejection VI = -12 to -23V, f = 120Hz IO = 40 mA, TJ = 25°C SVR Vd Table 14. Symbol Parameter VO Output voltage ΔVO Line regulation ΔVO Load regulation Quiescent current Test conditions mA 37 70 µV 44 dB 1.7 V Min. Typ. Max. Unit TJ = 25°C -11.5 -12 -12.5 V IO = 1 to 40 mA, VI = -14.5 to -27 V -11.4 -12.6 IO = 1 to 70 mA, VI = -19 V -11.4 -12.6 250 VI = -16 to -27 V, TJ = 25°C 200 IO = 1 to 100 mA, TJ = 25°C 100 IO = 1 to 40 mA, TJ = 25°C 50 TJ = 25°C 6.5 mA TJ = 125°C 6 mA mV mV IO = 1 to 40 mA 0.1 VI = -16 to -27 V 1.5 Quiescent current change eN Output noise voltage B =10Hz to 100kHz, TJ = 25°C Supply voltage rejection VI = -15 to -25V, f = 120Hz IO = 40 mA, TJ = 25°C Dropout voltage V VI = -14.5 to -27 V, TJ = 25°C ΔId Vd mV Electrical characteristics of L79L12AB and L79L12AC (refer to the test circuits, VI = - 19 V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF, TJ = 0 to 125 °C for L79L05AC, TJ = -40 to 125 °C for L79L05AB, unless otherwise specified) Output voltage SVR mV Dropout voltage VO Id V mA 37 80 µV 42 dB 1.7 V 11/22 Electrical characteristics Table 15. Symbol Electrical characteristics of L79L15AB and L79L15AC (refer to the test circuits, VI = - 23 V, IO = 40 mA, CI = 0.33 µF, CO = 0.1 µF, TJ = 0 to 125 °C for L79L05AC, TJ = -40 to 125 °C for L79L05AB, unless otherwise specified) Parameter VO Output voltage VO Output voltage ΔVO Line regulation ΔVO Load regulation Id L79LxxAB - L79LxxAC - L79LxxC Quiescent current Test conditions Min. Typ. Max. Unit TJ = 25°C -14.4 -15 -15.6 V IO = 1 to 40 mA, VI = -17.5 to -30 V -14.25 -15.75 IO = 1 to 70 mA, VI = -23 V -14.25 -15.75 VI = -17.5 to -30 V, TJ = 25°C 300 VI = -20 to -30 V, TJ = 25°C 250 IO = 1 to 100 mA, TJ = 25°C 150 IO = 1 to 40 mA, TJ = 25°C 75 TJ = 25°C 6.5 mA TJ = 125°C 6 mA VI = -20 to -30 V 1.5 eN Output noise voltage B =10Hz to 100kHz, TJ = 25°C Supply voltage rejection VI = -18.5 to -28.5.V, f = 120Hz IO = 40 mA, TJ = 25°C 12/22 Dropout voltage mV 0.1 Quiescent current change Vd mV IO = 1 to 40 mA ΔId SVR V mA 34 90 µV 39 dB 1.7 V L79LxxAB - L79LxxAC - L79LxxC 5 Package mechanical data Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a lead-free second level interconnect. The category of second Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. 13/22 Package mechanical data L79LxxAB - L79LxxAC - L79LxxC SO-8 mechanical data Dim. mm. Min. Typ. inch. Max. Min. Typ. Max. A 1.35 1.75 0.053 0.069 A1 0.10 0.25 0.04 0.010 A2 1.10 1.65 0.043 0.065 B 0.33 0.51 0.013 0.020 C 0.19 0.25 0.007 0.010 D 4.80 5.00 0.189 0.197 E 3.80 4.00 0.150 0.157 e 1.27 0.050 H 5.80 6.20 0.228 0.244 h 0.25 0.50 0.010 0.020 L 0.40 1.27 0.016 0.050 k ddd 8° (max.) 0.1 0.04 0016023/C 14/22 L79LxxAB - L79LxxAC - L79LxxC Package mechanical data SOT-89 mechanical data mm. mils. Dim. Min. Typ. Max. Min. Typ. Max. A 1.4 1.6 55.1 63.0 B 0.44 0.56 17.3 22.0 B1 0.36 0.48 14.2 18.9 C 0.35 0.44 13.8 17.3 C1 0.35 0.44 13.8 17.3 D 4.4 4.6 173.2 181.1 D1 1.62 1.83 63.8 72.0 E 2.29 2.6 90.2 102.4 e 1.42 1.57 55.9 61.8 e1 2.92 3.07 115.0 120.9 H 3.94 4.25 155.1 167.3 L 0.89 1.2 35.0 47.2 P025H 15/22 Package mechanical data L79LxxAB - L79LxxAC - L79LxxC TO-92 mechanical data mm. mils. Dim. Min. Typ. Max. Min. Typ. Max. A 4.32 4.95 170.1 194.9 b 0.36 0.51 14.2 20.1 D 4.45 4.95 175.2 194.9 E 3.30 3.94 129.9 155.1 e 2.41 2.67 94.9 105.1 e1 1.14 1.40 44.9 55.1 L 12.7 15.49 500.0 609.8 R 2.16 2.41 85.0 94.9 S1 0.92 1.52 36.2 59.8 W 0.41 0.56 16.1 22.0 α 5° 5° 0102782/D 16/22 L79LxxAB - L79LxxAC - L79LxxC Package mechanical data Tape & reel SO-8 mechanical data mm. inch. Dim. Min. A Typ. Max. Min. 330 Max. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 13.2 Typ. 0.504 22.4 0.519 0.882 Ao 8.1 8.5 0.319 0.335 Bo 5.5 5.9 0.216 0.232 Ko 2.1 2.3 0.082 0.090 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 17/22 Package mechanical data L79LxxAB - L79LxxAC - L79LxxC Tape & reel SOT89 mechanical data mm. inch. Dim. Min. Typ. A Min. Typ. 180 13.0 13.2 Max. 7.086 C 12.8 D 20.2 0.795 N 60 2.362 T 18/22 Max. 0.504 0.512 14.4 0.519 0.567 Ao 4.70 4.80 4.90 0.185 0.189 0.193 Bo 4.30 4.40 4.50 0.169 0.173 0.177 Ko 1.70 1.80 1.90 0.067 0.071 0.075 Po 3.9 4.0 4.1 0.153 0.157 0.161 P 7.9 8.0 8.1 0.311 0.315 0.319 L79LxxAB - L79LxxAC - L79LxxC Package mechanical data Tape & reel for TO-92 mechanical data Dim. A1 T T1 T2 d P0 P2 F1, F2 delta H W W0 W1 W2 H H0 H1 D0 t L1 delta P u Φ1 Φ2 mm. Min. inch. Typ. Max. Min. 4.80 3.80 1.60 2.30 0.48 12.5 5.65 2.44 17.5 5.7 8.5 Typ. Max. 0.189 0.150 0.063 0.091 0.019 2.54 ±2 18.00 0.50 18.50 15.50 12.9 7.05 2.94 0.492 0.222 0.096 19.0 6.3 9.25 0.689 0.224 0.335 0.508 0.278 0.116 0.100 0.079 0.709 0.748 0.248 0.364 0.20 0.728 18.70 16.50 0.610 4.2 0.150 25.00 0.726 0.650 0.984 3.8 0.90 3 ±1 50 360 30 0.165 0.035 0.118 0.039 1.968 14.173 1.181 delta P T A1 T2 H1 T1 delta H H H0 d L W2 l1 W0 W W1 F1 F2 D0 P2 t P0 DRAWING NOT IN SCALE 19/22 Order codes L79LxxAB - L79LxxAC - L79LxxC 6 Order codes Table 16. Order codes Packaging Output voltage SO-8 TO92 (BAG) (1) SOT-89 L79L05ACD13TR L79L05ACZ L79L05ACUTR -5 V L79L05ABD13TR L79L05ABZ L79L05ABUTR -5 V L79L06CD13TR (2) L79L06ACD13TR L79L06ABD13TR (2) -6 V L79L06ACZ L79L06ACUTR -6 V L79L06ABZ L79L06ABUTR -6 V L79L08CD13TR (2) L79L08ACD13TR L79L08ABD13TR L79L09CD13TR (2) L79L09ABD13TR L79L08ABZ (2) L79L08ACUTR -8 V L79L08ABUTR (2) -8 V (2) -9 V L79L09ACZ L79L09ABZ (2) L79L09ACUTR L79L09ABUTR (2) (2) -9 V -9 V -12 V L79L12ACD13TR L79L12ACZ L79L12ACUTR -12 V L79L12ABD13TR (2) L79L12ABZ (2) L79L12ABUTR (2) -12 V L79L15CD13TR (2) L79L15ACD13TR L79L15ABD13TR 1. L79L08ACZ (2) L79L09ACD13TR (2) L79L12CD13TR -8 V (2) -15 V L79L15ACZ L79L15ABZ (2) L79L15ACUTR -15 V -15 V Available in Ammopak with the suffix "-AP" or in Tape & Reel with the suffix "TR". Please note that in these cases pins are shaped according to Tape & Reel specifications. 2. Available on request. 20/22 L79LxxAB - L79LxxAC - L79LxxC 7 Revision history Table 17. Document revision history Revision history Date Revision Changes 14-Mar-2005 9 Add Tape & Reel for TO-92. 15-Mar-2005 10 Add note on Table 3. 23-Dec-2005 11 Mistake on ordering Table in Header. 12-Sep-2006 12 Order codes updated. 25-Jul-2007 13 Pin connection for SOT-89 updated on Figure 2, add Table 1 in cover page. 04-Dec-2007 14 Modified: Table 16. 21/22 L79LxxAB - L79LxxAC - L79LxxC Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 22/22