TI MSP430F2619S-HT Mixed signal microcontroller Datasheet

MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
MIXED SIGNAL MICROCONTROLLER
Check for Samples: MSP430F2619S-HT
FEATURES
1
•
•
2
•
•
•
•
•
•
•
•
•
Low Supply Voltage Range 1.8 V to 3.6 V
Ultralow-Power Consumption
– Active Mode: 365 μA at 1 MHz, 2.2 V
– Standby Mode (VLO): 0.5 μA
– Off Mode (RAM Retention): 0.1 μA
Wake-Up From Standby Mode in Less than 1
μs
16-Bit RISC Architecture, 62.5-ns Instruction
Cycle Time
Three-Channel Internal DMA
12-Bit Analog-to-Digital (A/D) Converter With
Internal Reference, Sample-and-Hold, and
Autoscan Feature
Dual 12-Bit Digital-to-Analog (D/A) Converters
With Synchronization
16-Bit Timer_A With Three Capture/Compare
Registers
16-Bit Timer_B With Seven
Capture/Compare-With-Shadow Registers
On-Chip Comparator
Four Universal Serial Communication
Interfaces (USCIs)
– USCI_A0 and USCI_A1
– Enhanced UART Supporting
Auto-Baud-Rate Detection (LIN)
– IrDA Encoder and Decoder
– Synchronous SPI
– USCI_B0 and USCI_B1
– I2C™
– Synchronous SPI
•
•
•
•
•
•
•
Supply Voltage Supervisor/Monitor With
Programmable Level Detection
Brownout Detector
Bootstrap Loader
Serial Onboard Programming, No External
Programming Voltage Needed Programmable
Code Protection by Security Fuse
MSP430F2619S
120 kB + 256 B Flash Memory, 4 kB RAM
Available in 64-Pin QFP and KDG Packages
For Complete Module Descriptions, Refer to
the MSP430x2xx Family User's Guide
(SLAU144)
SUPPORTS EXTREME TEMPERATURE
APPLICATIONS
•
•
•
•
•
•
•
Controlled Baseline
One Assembly/Test Site
One Fabrication Site
Extended Product Life Cycle
Extended Product-Change Notification
Product Traceability
Texas Instruments high temperature products
utilize highly optimized silicon (die) solutions
with design and process enhancements to
maximize performance over extended
temperatures.
DESCRIPTION
The MSP430F2619S ultralow-power microcontroller features different sets of peripherals targeted for various
applications. The architecture, combined with five low power modes, is optimized to achieve extended battery life
in portable measurement applications. The device features a powerful 16-bit RISC CPU, 16-bit registers, and
constant generators that attribute to maximum code efficiency. The digitally controlled oscillator (DCO) allows
wake-up from low-power modes to active mode in less than 1 μs.
The MSP430F2619S is a microcontroller configuration with two built-in 16-bit timers, a fast 12-bit A/D converter,
a comparator, dual 12-bit D/A converters, four universal serial communication interface (USCI) modules, DMA,
and up to 64 I/O pins.
Typical applications include sensor systems that capture analog signals, convert them to digital values, and then
process the data for display or for transmission to a host system. Stand-alone RF sensor front end is another
area of application.
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Table 1. ORDERING INFORMATION (1)
TA
–55°C to 150°C
(1)
(2)
PACKAGE (2)
ORDERABLE PART NUMBER
QFP (PM)
MSP430F2619SPM
KGD
(known good die)
MSP430F2619SKGD1
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
Web site at www.ti.com.
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
DEVELOPMENT TOOL SUPPORT
All MSP430 microcontrollers include an Embedded Emulation Module (EEM) allowing advanced debugging and
programming through easy-to-use development tools. Recommended hardware options include:
• Debugging and Programming Interface
– MSP-FET430UIF (USB)
– MSP-FET430PIF (Parallel Port)
• Debugging and Programming Interface with Target Board
– MSP-FET430U64
– MSP-FET430U80
• Standalone Target Board
– MSP-TS430PM64
• Production Programmer
– MSP-GANG430
2
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
P5.5/SMCLK
P5.7/TBOUTH/SVSOUT
P5.6/ACLK
XT2IN
XT2OUT
TDI/TCLK
TDO/TDI
TCK
TMS
RST/NMI
P6.1/A1
P6.0/A0
AV SS
P6.2/A2
DVSS1
AV CC
PINOUTS
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
DVCC1
P6.3/A3
P6.4/A4
1
2
3
48
47
46
P5.4/MCLK
P5.3/UCB1CLK/UCA1STE
P5.2/UCB1SOMI/UCB1SCL
P6.5/A5/DAC1
P6.6/A6/DAC0
4
5
45
44
P5.1/UCB1SIMO/UCB1SDA
P5.0/UCB1STE/UCA1CLK
P6.7/A7/DAC1/SVSIN
VREF+
XIN
6
7
8
43
42
41
P4.7/TBCLK
P4.6/TB6
P4.5/TB5
40
39
P4.4/TB4
P4.3/TB3
64-PIN
PM PACKAGE
(TOP VIEW)
XOUT
Ve REF+/DAC0
9
10
VREF-/Ve REFP1.0/TACLK/CAOUT
P1.1/TA0
11
12
13
38
37
36
P4.2/TB2
P4.1/TB1
P4.0/TB0
P1.2/TA1
P1.3/TA2
14
15
35
34
P3.7/UCA1RXD/UCA1SOMI
P3.6/UCA1TXD/UCA1SIMO
P1.4/SMCLK
16
33
P3.5/UCA0RXD/UCA0SOMI
Copyright © 2010–2011, Texas Instruments Incorporated
P3.4/UCA0TXD/UCA0SIMO
P3.3/UCB0CLK/UCA0STE
P3.2/UCB0SOMI/UCB0SCL
P3.0/UCB0STE/UCA0CLK
P3.1/UCB0SIMO/UCB0SDA
P2.7/TA0/CA7
P2.6/ADC12CLK/DMAE0/CA6
P2.5/ROSC/CA5
P2.3/CA0/TA1
P2.4/CA1/TA2
P2.1/TAINCLK/CA3
P2.2/CAOUT/TA0/CA4
P2.0/ACLK/CA2
P1.7/TA2
P1.5/TA0
P1.6/TA1
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
3
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
KGD PAD 1 DESIGNATOR
4
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
FUNCTIONAL BLOCK DIAGRAM
XIN/
XT2IN
XOUT/
XT2OUT
2
2
DVCC
ACLK
Oscillators
Basic Clock SMCLK
System+
MCLK
16MHz
CPU
1MB
incl. 16
Registers
Emulation
JTAG
Interface
Flash
120kB
116kB
92kB
92kB
56kB
DVSS
AVCC
RAM
4kB
8kB
8kB
4kB
4kB
ADC12
12-Bit
8
Channels
AVSS 1.x/P2.x
P
DAC12
12-Bit
2
Channels
Voltage
Out
P3.x/P4.x
P5.x/P6.x
2x8
4x8
Ports
P1/P2
2x8 I/O
Interrupt
capability
Ports
P3/P4
P5/P6
USCI A0
UART/
LIN,
IrDA, SPI
4x8 I/O
USCI B0
SPI, I2C
MAB
MDB
Brownout
Protection
SVS,
SVM
Hardware
Multiplier
MPY,
MPYS,
MAC,
MACS
DMA
Controller
3
Channels
Timer_B7
Watchdog
WDT+
15-Bit
Timer_A3
3 CC
Registers
Comp_A+
7 CC
Registers,
Shadow
Reg
8
Channels
USCI A1
UART/
LIN,
IrDA, SPI
USCI B1
SPI, I2C
RST/NMI
Copyright © 2010–2011, Texas Instruments Incorporated
5
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
TERMINAL FUNCTIONS (64-PM PACKAGE)
TERMINAL
NAME
PM
I/O
DESCRIPTION
AVCC
64
Analog supply voltage, positive terminal. Supplies only the analog portion of
ADC12 and DAC12.
AVSS
62
Analog supply voltage, negative terminal. Supplies only the analog portion of
ADC12 and DAC12.
DVCC1
1
Digital supply voltage, positive terminal. Supplies all digital parts.
DVSS1
63
Digital supply voltage, negative terminal. Supplies all digital parts.
P1.0/TACLK/CAOUT
12
I/O
General-purpose digital I/O pin/Timer_A, clock signal TACLK
input/Comparator_A output
P1.1/TA0
13
I/O
General-purpose digital I/O pin/Timer_A, capture: CCI0A input, compare:
Out0 output/BSL transmit
P1.2/TA1
14
I/O
General-purpose digital I/O pin/Timer_A, capture: CCI1A input, compare:
Out1 output
P1.3/TA2
15
I/O
General-purpose digital I/O pin/Timer_A, capture: CCI2A input, compare:
Out2 output
P1.4/SMCLK
16
I/O
General-purpose digital I/O pin/SMCLK signal output
P1.5/TA0
17
I/O
General-purpose digital I/O pin/Timer_A, compare: Out0 output
P1.6/TA1
18
I/O
General-purpose digital I/O pin/Timer_A, compare: Out1 output
P1.7/TA2
19
I/O
General-purpose digital I/O pin/Timer_A, compare: Out2 output
P2.0/ACLK/CA2
20
I/O
General-purpose digital I/O pin/ACLK output/Comparator_A input
P2.1/TAINCLK/CA3
21
I/O
General-purpose digital I/O pin/Timer_A, clock signal at INCLK
P2.2/CAOUT/TA0/CA4
22
I/O
General-purpose digital I/O pin/Timer_A, capture: CCI0B
input/Comparator_A output/BSL receive/Comparator_A input
P2.3/CA0/TA1
23
I/O
General-purpose digital I/O pin/Timer_A, compare: Out1
output/Comparator_A input
P2.4/CA1/TA2
24
I/O
General-purpose digital I/O pin/Timer_A, compare: Out2
output/Comparator_A input
P2.5/Rosc/CA5
25
I/O
General-purpose digital I/O pin/input for external resistor defining the DCO
nominal frequency/Comparator_A input
P2.6/ADC12CLK/DMAE0/CA6
26
I/O
General-purpose digital I/O pin/conversion clock – 12-bit ADC/DMA channel
0 external trigger/Comparator_A input
P2.7/TA0/CA7
27
I/O
General-purpose digital I/O pin/Timer_A, compare: Out0
output/Comparator_A input
P3.0/UCB0STE/UCA0CLK
28
I/O
General-purpose digital I/O pin/USCI B0 slave transmit enable/USCI A0
clock input/output
P3.1/UCB0SIMO/UCB0SDA
29
I/O
General-purpose digital I/O pin/USCI B0 slave in/master out in SPI mode,
SDA I2C data in I2C mode
P3.2/UCB0SOMI/UCB0SCL
30
I/O
General-purpose digital I/O pin/USCI B0 slave out/master in in SPI mode,
SCL I2C clock in I2C mode
P3.3/UCB0CLK/UCA0STE
31
I/O
General-purpose digital I/O/USCI B0 clock input/output, USCI A0 slave
transmit enable
P3.4/UCA0TXD/UCA0SIMO
32
I/O
General-purpose digital I/O pin/USCIA transmit data output in UART mode,
slave data in/master out in SPI mode
P3.5/UCA0RXD/UCA0SOMI
33
I/O
General-purpose digital I/O pin/USCI A0 receive data input in UART mode,
slave data out/master in in SPI mode
P3.6/UCA1TXD/UCA1SIMO
34
I/O
General-purpose digital I/O pin/USCI A1 transmit data output in UART
mode, slave data in/master out in SPI mode
P3.7/UCA1RXD/UCA1SOMI
35
I/O
General-purpose digital I/O pin/USCIA1 receive data input in UART mode,
slave data out/master in in SPI mode
P4.0/TB0
36
I/O
General-purpose digital I/O pin/Timer_B, capture: CCI0A/B input, compare:
Out0 output
P4.1/TB1
37
I/O
General-purpose digital I/O pin/Timer_B, capture: CCI1A/B input, compare:
Out1 output
P4.2/TB2
38
I/O
General-purpose digital I/O pin/Timer_B, capture: CCI2A/B input, compare:
Out2 output
6
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
TERMINAL FUNCTIONS (64-PM PACKAGE) (continued)
TERMINAL
NAME
PM
I/O
DESCRIPTION
P4.3/TB3
39
I/O
General-purpose digital I/O pin/Timer_B, capture: CCI3A/B input, compare:
Out3 output
P4.4/TB4
40
I/O
General-purpose digital I/O pin/Timer_B, capture: CCI4A/B input, compare:
Out4 output
P4.5/TB5
41
I/O
General-purpose digital I/O pin/Timer_B, capture: CCI5A/B input, compare:
Out5 output
P4.6/TB6
42
I/O
General-purpose digital I/O pin/Timer_B, capture: CCI6A input, compare:
Out6 output
P4.7/TBCLK
43
I/O
General-purpose digital I/O pin/Timer_B, clock signal TBCLK input
P5.0/UCB1STE/UCA1CLK
44
I/O
General-purpose digital I/O pin/USCI B1 slave transmit enable/USCI A1
clock input/output
P5.1/UCB1SIMO/UCB1SDA
45
I/O
General-purpose digital I/O pin/USCI B1slave in/master out in SPI mode,
SDA I2C data in I2C mode
P5.2/UCB1SOMI/UCB1SCL
46
I/O
General-purpose digital I/O pin/USCI B1slave out/master in in SPI mode,
SCL I2C clock in I2C mode
P5.3/UCB1CLK/UCA1STE
47
I/O
General-purpose digital I/O/USCI B1 clock input/output, USCI A1 slave
transmit enable
P5.4/MCLK
48
I/O
General-purpose digital I/O pin/main system clock MCLK output
P5.5/SMCLK
49
I/O
General-purpose digital I/O pin/submain system clock SMCLK output
P5.6/ACLK
50
I/O
General-purpose digital I/O pin/auxiliary clock ACLK output
P5.7/TBOUTH/SVSOUT
51
I/O
General-purpose digital I/O pin/switch all PWM digital output ports to high
impedance -- Timer_B TB0 to TB6/SVS comparator output
P6.0/A0
59
I/O
General-purpose digital I/O pin/analog input A0 – 12-bit ADC
P6.1/A1
60
I/O
General-purpose digital I/O pin/analog input A1 – 12-bit ADC
P6.2/A2
61
I/O
General-purpose digital I/O pin/analog input A2 – 12-bit ADC
P6.3/A3
2
I/O
General-purpose digital I/O pin/analog input A3 – 12-bit ADC
P6.4/A4
3
I/O
General-purpose digital I/O pin/analog input A4 – 12-bit ADC
P6.5/A5/DAC1
4
I/O
General-purpose digital I/O pin/analog input A5 – 12-bit ADC/DAC12.1
output
P6.6/A6/DAC0
5
I/O
General-purpose digital I/O pin/analog input A6 – 12-bit ADC/DAC12.0
output
P6.7/A7/DAC1/SVSIN
6
I/O
General-purpose digital I/O pin/analog input a7 – 12-bit ADC/DAC12.1
output/SVS input
P7.0
NC
I/O
General-purpose digital I/O pin
P7.1
NC
I/O
General-purpose digital I/O pin
P7.2
NC
I/O
General-purpose digital I/O pin
P7.3
NC
I/O
General-purpose digital I/O pin
P7.4
NC
I/O
General-purpose digital I/O pin
P7.5
NC
I/O
General-purpose digital I/O pin
P7.6
NC
I/O
General-purpose digital I/O pin
P7.7
NC
I/O
General-purpose digital I/O pin
P8.0
NC
I/O
General-purpose digital I/O pin
P8.1
NC
I/O
General-purpose digital I/O pin
P8.2
NC
I/O
General-purpose digital I/O pin
P8.3
NC
I/O
General-purpose digital I/O pin
P8.4
NC
I/O
General-purpose digital I/O pin
P8.5
NC
I/O
General-purpose digital I/O pin
P8.6/XT2OUT
NC
O
General-purpose digital I/O pin/Output terminal of crystal oscillator XT2
P8.7/XT2IN
NC
I
General-purpose digital I/O pin/Input port for crystal oscillator XT2. Only
standard crystals can be connected.
Copyright © 2010–2011, Texas Instruments Incorporated
7
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
TERMINAL FUNCTIONS (64-PM PACKAGE) (continued)
TERMINAL
NAME
PM
I/O
DESCRIPTION
XT2OUT
52
O
Output terminal of crystal oscillator XT2
XT2IN
53
I
Input port for crystal oscillator XT2
RST/NMI
58
I
Reset input, nonmaskable interrupt input port, or bootstrap loader start (in
flash devices)
TCK
57
I
Test clock (JTAG). TCK is the clock input port for device programming test
and bootstrap loader start.
TDI/TCLK
55
I
Test data input or test clock input. The device protection fuse is connected
to TDI/TCLK.
TDO/TDI
54
I/O
TMS
56
I
Test mode select. TMS is used as an input port for device programming and
test.
VeREF+/DAC0
10
I
Input for an external reference voltage/DAC12.0 output
VREF+
7
O
Output of positive terminal of the reference voltage in the ADC12
VREF-/VeREF-
11
I
Negative terminal for the reference voltage for both sources, the internal
reference voltage, or an external applied reference voltage
XIN
8
I
Input port for crystal oscillator XT1. Standard or watch crystals can be
connected.
XOUT
9
O
Output port for crystal oscillator XT1. Standard or watch crystals can be
connected.
8
Test data output port. TDO/TDI data output or programming data input
terminal.
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
KGD INFORMATION
PAD
FUNCTION
BOND PAD CO-ORDINATES
BOND PAD SIZE
BOND PAD CENTER
Xmin (µm)
Ymin (µm)
Xmax (µm)
Ymax (µm)
X (µm)
Y (µm)
Xp (µm)
Yp (µm)
1
AVCC
90.65
4729.1
165.65
4804.1
75
75
128.15
4766.6
2
DVCC1
90.65
4586.85
165.65
4661.85
75
75
128.15
4624.35
3
P6.3/A3
87.4
4440.3
162.4
4515.3
75
75
124.9
4477.8
4
P6.4/A4
87.4
4282.65
162.4
4357.65
75
75
124.9
4320.15
5
P6.5/A5/DAC1
87.4
4125.05
162.4
4200.05
75
75
124.9
4162.55
6
P6.6/A6/DAC0
87.4
3943.9
162.4
4018.9
75
75
124.9
3981.4
7
P6.7/A7/DAC1/SVSIN
87.4
3762.75
162.4
3837.75
75
75
124.9
3800.25
8
VREF+
92.95
3524.75
167.95
3599.75
75
75
130.45
3562.25
9
XIN
87.4
3346.6
162.4
3421.6
75
75
124.9
3384.1
10
XOUT
87.4
2472.4
162.4
2547.4
75
75
124.9
2509.9
11
VeREF+/DAC0
92.95
2251
167.95
2326
75
75
130.45
2288.5
12
VREF-/VeREF-
92.95
2082.5
167.95
2157.5
75
75
130.45
2120
13
P1.0/TACLK/CAOUT
87.4
1866.2
162.4
1941.2
75
75
124.9
1903.7
14
P1.1/TA0
87.4
1730.6
162.4
1805.6
75
75
124.9
1768.1
15
P1.2/TA1
87.4
1595
162.4
1670
75
75
124.9
1632.5
16
P1.3/TA2
87.4
1459.4
162.4
1534.4
75
75
124.9
1496.9
17
P1.4/SMCLK
87.4
1323.8
162.4
1398.8
75
75
124.9
1361.3
18
P1.5/TA0
87.4
1188.2
162.4
1263.2
75
75
124.9
1225.7
19
P1.6/TA1
87.4
1052.6
162.4
1127.6
75
75
124.9
1090.1
20
P1.7/TA2
87.4
807.7
162.4
882.7
75
75
124.9
845.2
21
P2.0/ACLK/CA2
87.4
672.1
162.4
747.1
75
75
124.9
709.6
22
P2.1/TAINCLK/CA3
559.1
87.4
634.1
162.4
75
75
596.6
124.9
23
P2.2/CAOUT/TA0/CA4
694.7
87.4
769.7
162.4
75
75
732.2
124.9
24
P2.3/CA0/TA1
830.3
87.4
905.3
162.4
75
75
867.8
124.9
25
P2.4/CA1/TA2
1234.9
87.4
1309.9
162.4
75
75
1272.4
124.9
26
P2.5/Rosc/CA5
1370.5
87.4
1445.5
162.4
75
75
1408
124.9
27
P2.6/ADC12CLK/DMAE0/CA6
1506.1
87.4
1581.1
162.4
75
75
1543.6
124.9
28
P2.7/TA0/CA7
1641.7
87.4
1716.7
162.4
75
75
1679.2
124.9
29
P3.0/UCB0STE/UCA0CLK
1777.3
87.4
1852.3
162.4
75
75
1814.8
124.9
30
P3.1/UCB0SIMO/UCB0SDA
1912.9
87.4
1987.9
162.4
75
75
1950.4
124.9
31
P3.2/UCBOSOMI/UCB0SCL
2053
87.4
2128
162.4
75
75
2090.5
124.9
32
P3.3/UCB0CLK/UCA0STE
2193.1
87.4
2268.1
162.4
75
75
2230.6
124.9
33
P3.4/UCA0TXD/UCA0SIMO
2328.7
87.4
2403.7
162.4
75
75
2366.2
124.9
34
P3.5/UCA0RXD/UCA0SOMI
2464.3
87.4
2539.3
162.4
75
75
2501.8
124.9
35
P3.6/UCA1TXD/UCA1SIMO
2671.1
87.4
2746.1
162.4
75
75
2708.6
124.9
36
P3.7/UCA1RXD/UCA1SOMI
2807.15
87.4
2882.15
162.4
75
75
2844.65
124.9
37
P4.0/TB0
3585.9
87.4
3660.9
162.4
75
75
3623.4
124.9
38
P4.1/TB1
3721.5
87.4
3796.5
162.4
75
75
3759
124.9
39
P4.2/TB2
3861.6
87.4
3936.6
162.4
75
75
3899.1
124.9
40
P4.3/TB3
4001.7
87.4
4076.7
162.4
75
75
4039.2
124.9
41
P4.4/TB4
4137.3
87.4
4212.3
162.4
75
75
4174.8
124.9
42
P4.5/TB5
4887.6
669.65
4962.6
744.65
75
75
4925.1
707.15
43
P4.6/TB6
4887.6
805.25
4962.6
880.25
75
75
4925.1
842.75
44
P4.7/TBCLK
4887.6
940.85
4962.6
1015.85
75
75
4925.1
978.35
45
P5.0/UCB1STE/UCA1CLK
4887.6
1076.45
4962.6
1151.45
75
75
4925.1
1113.95
46
P5.1/UCB1SIMO/UCB1SDA
4887.6
1212.05
4962.6
1287.05
75
75
4925.1
1249.55
47
P5.2/UCB1SOMI/UCB1SCL
4887.6
1352.15
4962.6
1427.15
75
75
4925.1
1389.65
48
P5.3/UCB1CLK/UCA1STE
4887.6
1492.25
4962.6
1567.25
75
75
4925.1
1529.75
49
P5.4/MCLK
4887.6
1627.85
4962.6
1702.85
75
75
4925.1
1665.35
50
P5.5/SMCLK
4887.6
2533.55
4962.6
2608.55
75
75
4925.1
2571.05
Copyright © 2010–2011, Texas Instruments Incorporated
9
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
KGD INFORMATION (continued)
PAD
FUNCTION
BOND PAD CO-ORDINATES
BOND PAD SIZE
BOND PAD CENTER
Xmin (µm)
Ymin (µm)
Xmax (µm)
Ymax (µm)
X (µm)
Y (µm)
Xp (µm)
Yp (µm)
51
P5.6/ACLK
4887.6
2669.15
4962.6
2744.15
75
75
4925.1
2706.65
52
P5.7/TBOUTH/SVSOUT
4887.6
2804.75
4962.6
2879.75
75
75
4925.1
2842.25
53
DVCC2
4884.35
2953.25
4959.35
3028.25
75
75
4921.85
2990.75
54
DVSS2
4887.6
3060.45
4962.6
3135.45
75
75
4925.1
3097.95
55
P7.0
4887.6
3153.45
4962.6
3228.45
75
75
4925.1
3190.95
56
P7.1
4887.6
3289.05
4962.6
3364.05
75
75
4925.1
3326.55
57
P7.2
4887.6
3424.65
4962.6
3499.65
75
75
4925.1
3462.15
58
P7.3
4887.6
3560.25
4962.6
3635.25
75
75
4925.1
3597.75
59
P7.4
4887.6
3700.35
4962.6
3775.35
75
75
4925.1
3737.85
60
P7.5
4887.6
3840.45
4962.6
3915.45
75
75
4925.1
3877.95
61
P7.6
4887.6
3997.05
4962.6
4072.05
75
75
4925.1
4034.55
62
P7.7
4237.65
4887.6
4312.65
4962.6
75
75
4275.15
4925.1
63
P8.0
4102.05
4887.6
4177.05
4962.6
75
75
4139.55
4925.1
64
P8.1
3966.45
4887.6
4041.45
4962.6
75
75
4003.95
4925.1
65
P8.2
3830.85
4887.6
3905.85
4962.6
75
75
3868.35
4925.1
66
P8.3
3547.7
4887.6
3622.7
4962.6
75
75
3585.2
4925.1
67
P8.4
3412.1
4887.6
3487.1
4962.6
75
75
3449.6
4925.1
68
P8.5
3276.5
4887.6
3351.5
4962.6
75
75
3314
4925.1
69
P8.6/XT2OUT
3140.9
4887.6
3215.9
4962.6
75
75
3178.4
4925.1
70
P8.7/XT2IN
2992.85
4887.6
3067.85
4962.6
75
75
3030.35
4925.1
71
TDO/TDI
2844.6
4887.6
2919.6
4962.6
75
75
2882.1
4925.1
72
TDI/TCLK
2448
4887.6
2523
4962.6
75
75
2485.5
4925.1
73
TMS
2152.25
4887.6
2227.25
4962.6
75
75
2189.75
4925.1
74
TCK
1568.55
4887.6
1643.55
4962.6
75
75
1606.05
4925.1
75
RST/NMI
1431.85
4887.6
1506.85
4962.6
75
75
1469.35
4925.1
76
P6.0/A0
1230.75
4887.6
1305.75
4962.6
75
75
1268.25
4925.1
77
P6.1/A1
1077.9
4887.6
1152.9
4962.6
75
75
1115.4
4925.1
78
P6.2/A2
923.95
4887.6
998.95
4962.6
75
75
961.45
4925.1
79
AVSS
821.05
4887.95
896.05
4962.95
75
75
858.55
4925.45
80
AVSS
674.95
4887.6
749.95
4962.6
75
75
712.45
4925.1
81
DVSS1
499.2
4887.6
574.2
4962.6
75
75
536.7
4925.1
82
AVCC
337.85
4884.35
412.85
4959.35
75
75
375.35
4921.85
10
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
SHORT-FORM DESCRIPTION
CPU
The MSP430 CPU has a 16-bit RISC architecture
that is highly transparent to the application. All
operations, other than program-flow instructions, are
performed as register operations in conjunction with
seven addressing modes for source operand and four
addressing modes for destination operand.
Program Counter
PC/R0
Stack Pointer
SP/R1
Status Register
SR/CG1/R2
Constant Generator
CG2/R3
General-Purpose Register
R4
General-Purpose Register
R5
General-Purpose Register
R6
General-Purpose Register
R7
General-Purpose Register
R8
Peripherals are connected to the CPU using data,
address, and control buses, and can be handled with
all instructions.
General-Purpose Register
R9
General-Purpose Register
R10
Instruction Set
General-Purpose Register
R11
The instruction set consists of 51 instructions with
three formats and seven address modes. Each
instruction can operate on word and byte data.
Table 2 shows examples of the three types of
instruction formats; the address modes are listed in
Table 3.
General-Purpose Register
R12
General-Purpose Register
R13
General-Purpose Register
R14
General-Purpose Register
R15
The CPU is integrated with 16 registers that provide
reduced
instruction
execution
time.
The
register-to-register operation execution time is one
cycle of the CPU clock.
Four of the registers, R0 to R3, are dedicated as
program counter, stack pointer, status register, and
constant generator respectively. The remaining
registers are general-purpose registers.
Table 2. Instruction Word Formats
Dual operands, source-destination
e.g., ADD R4,R5
R4 + R5 → R5
Single operands, destination only
e.g., CALL R8
PC → (TOS), R8 → PC
Relative jump, un/conditional
e.g., JNE
Jump-on-equal bit = 0
Table 3. Address Mode Descriptions
ADDRESS MODE
(1)
(2)
S
(1)
D
(2)
SYNTAX
EXAMPLE
Register
•
•
MOV Rs,Rd
MOV R10,R11
OPERATION
R10 → R11
Indexed
•
•
MOV X(Rn),Y(Rm)
MOV 2(R5),6(R6)
M(2+R5) → M(6+R6)
Symbolic (PC relative)
•
•
MOV EDE,TONI
M(EDE) → M(TONI)
Absolute
•
•
MOV &MEM,&TCDAT
M(MEM) → M(TCDAT)
Indirect
•
MOV @Rn,Y(Rm)
MOV @R10,Tab(R6)
M(R10) → M(Tab+R6)
Indirect autoincrement
•
MOV @Rn+,Rm
MOV @R10+,R11
M(R10) → R11
R10 + 2 → R10
Immediate
•
MOV #X,TONI
MOV #45,TONI
#45 → M(TONI)
S = source
D = destination
Copyright © 2010–2011, Texas Instruments Incorporated
11
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Operating Modes
The MSP430 has one active mode and five software selectable low-power modes of operation. An interrupt
event can wake up the device from any of the five low-power modes, service the request and restore back to the
low-power mode on return from the interrupt program.
The following six operating modes can be configured by software:
• Active mode ( AM)
– All clocks are active.
• Low-power mode 0 (LPM0)
– CPU is disabled.
– ACLK and SMCLK remain active. MCLK is disabled.
• Low-power mode 1 (LPM1)
– CPU is disabled.
– ACLK and SMCLK remain active. MCLK is disabled.
– DCO’s dc generator is disabled if DCO not used in active mode.
• Low-power mode 2 (LPM2)
– CPU is disabled.
– MCLK and SMCLK are disabled.
– DCO's dc-generator remains enabled.
– ACLK remains active
• Low-power mode 3 (LPM3)
– CPU is disabled.
– MCLK and SMCLK are disabled.
– DCO's dc-generator is disabled.
– ACLK remains active.
• Low-power mode 4 (LPM4)
– CPU is disabled.
– ACLK is disabled.
– MCLK and SMCLK are disabled.
– DCO's dc-generator is disabled.
– Crystal oscillator is stopped.
12
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Interrupt Vector Addresses
The interrupt vectors and the power-up starting address are located in the address range of 0FFFF–0FFC0h.
The vector contains the 16-bit address of the appropriate interrupt handler instruction sequence.
If the reset vector (located at address 0FFFEh) contains 0FFFFh (e.g., flash is not programmed), the CPU goes
into LPM4 immediately after power up.
INTERRUPT SOURCE
INTERRUPT FLAG
Power up
External reset
Watchdog
Flash key violation
PC out-of-range (1)
PORIFG
RSTIFG
WDTIFG
KEYV
NMI
Oscillator fault
Flash memory access violation
Reset
0x0FFFE
31, highest
(non)-maskable,
(non)-maskable,
(non)-maskable
0x0FFFC
30
(2)
NMIIFG
OFIFG
ACCVIFG (2)
(3)
maskable
0x0FFFA
29
Timer_B7
TBCCR1 and TBCCR2
CCIFGs, TBIFG (2) (4)
maskable
0x0FFF8
28
Comparator_A+
CAIFG
maskable
0x0FFF6
27
Watchdog timer+
WDTIFG
maskable
0x0FFF4
26
maskable
0x0FFF2
25
maskable
0x0FFF0
24
maskable
0x0FFEE
23
maskable
0x0FFEC
22
maskable
0x0FFEA
21
0x0FFE8
20
maskable
0x0FFE6
19
maskable
0x0FFE4
18
maskable
0x0FFE2
17
maskable
0x0FFE0
16
maskable
0x0FFDE
15
maskable
0x0FFDC
14
0x0FFDA to 0x0FFC0
13 to 0, lowest
USCI_A0/USCI_B0 receive
USCI_B0 I2C status
USCI_A0/USCI_B0 transmit
USCI_B0 I2C receive/transmit
TACCR0 CCIFG
(4)
TACCR1 CCIFG,
TACCR2 CCIFG,
TAIFG (2) (4)
UCA0RXIFG, UCB0RXIFG (2)
ADC12IFG
(4)
(2) (4)
I/O port P2 (eight flags)
P2IFG.0 to P2IFG.7
I/O port P1 (eight flags)
P1IFG.0 to P1IFG.7 (2)
USCI_A0/USCI_B1 receive
USCI_B1 I2C status
USCI_A1/USCI_B1 transmit
USCI_B1 I2C receive/transmit
DMA
DAC12
(5)
UCA0TXIFG, UCB0TXIFG (2) (6)
ADC12
(4)
UCA1RXIFG, UCB1RXIFG
(2) (5)
UCA1TXIFG, UCB1TXIFG (2)
(6)
DMA0IFG, DMA1IFG,
DMA2IFG (2) (4)
DAC12_0IFG, DAC12_1IFG (2)
Reserved (7) (8)
(8)
PRIORITY
TBCCR0 CCIFG (4)
Timer_A3
(2)
(3)
(4)
(5)
(6)
(7)
WORD ADDRESS
Timer_B7
Timer_A3
(1)
SYSTEM
INTERRUPT
(4)
Reserved
A reset is generated if the CPU tries to fetch instructions from within the module register memory address range (0x00000 – 0x001FF)
or from within unused address range.
Multiple source flags
(non)-maskable: the individual interrupt-enable bit can disable an interrupt event, but the general interrupt enable cannot.
Interrupt flags are located in the module.
In SPI mode: UCB0RXIFG. In I2C mode: UCALIFG, UCNACKIFG, ICSTTIFG, UCSTPIFG.
In UART/SPI mode: UCB0TXIFG. In I2C mode: UCB0RXIFG, UCB0TXIFG.
The address 0x0FFBE is used as bootstrap loader security key (BSLSKEY). A 0x0AA55 at this location disables the BSL completely. A
zero disables the erasure of the flash if an invalid password is supplied.
The interrupt vectors at addresses 0x0FFDC to 0x0FFC0 are not used in this device and can be used for regular program code if
necessary.
Copyright © 2010–2011, Texas Instruments Incorporated
13
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Special Function Registers
Most interrupt and module enable bits are collected into the lowest address space. Special function register bits
not allocated to a functional purpose are not physically present in the device. Simple software access is provided
with this arrangement.
Interrupt Enable 1 and 2
Address
7
6
00h
5
4
1
0
ACCVIE
NMIIE
3
2
OFIE
WDTIE
rw-0
rw-0
rw-0
rw-0
WDTIE:
Watchdog Timer interrupt enable. Inactive if watchdog mode is selected. Active if Watchdog Timer
is configured in interval timer mode.
OFIE:
Oscillator fault enable
NMIIE:
(Non)maskable interrupt enable
ACCVIE:
Flash access violation interrupt enable
Address
7
6
5
4
01h
UCA0RXIE
USCI_A0 receive-interrupt enable
UCA0TXIE
USCI_A0 transmit-interrupt enable
UCB0RXIE
USCI_B0 receive-interrupt enable
UCB0TXIE
USCI_B0 transmit-interrupt enable
3
2
1
0
UCB0TXIE
UCB0RXIE
UCA0TXIE
UCA0RXIE
rw-0
rw-0
rw-0
rw-0
Interrupt Flag Register 1 and 2
Address
7
6
5
02h
4
3
2
1
0
NMIIFG
RSTIFG
PORIFG
OFIFG
WDTIFG
rw-0
rw-(0)
rw-(1)
rw-1
rw-(0)
WDTIFG: Set on Watchdog Timer overflow (in watchdog mode) or security key violation.
Reset on VCC power-up or a reset condition at RST/NMI pin in reset mode.
OFIFG:
Flag set on oscillator fault7
RSTIFG:
External reset interrupt flag. Set on a reset condition at RST/NMI pin in reset mode. Reset on VCC
power up.
PORIFG: Power-On Reset interrupt flag. Set on VCC power up.
NMIIFG:
Address
Set via RST/NMI-pin
7
6
5
03h
4
3
2
1
0
UCB0
TXIFG
UCB0
RXIFG
UCA0
TXIFG
UCA0
RXIFG
rw-1
rw-0
rw-1
rw-0
UCA0RXIFG USCI_A0 receive-interrupt flag
UCA0TXIFG USCI_A0 transmit-interrupt flag
UCB0RXIFG USCI_B0 receive-interrupt flag
UCB0TXIFG USCI_B0 transmit-interrupt flag
xxx
14
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Legend:
rw:
Bit can be read and written.
rw-0, 1:
Bit can be read and written. It is Reset or Set by PUC.
rw-(0), (1):
Bit can be read and written. It is Reset or Set by POR.
SFR bit is not present in device.
Memory Organization
MSP430F2619
Size
Flash
Flash
120 kB Flash
0x0FFFF – 0x0FFC0
0x0FFFF – 0x02100
RAM (total)
Size
4 kB
0x020FF -- 0x01100
Extended
Size
2 kB
0x020FF -- 0x01900
Mirrored
Size
2 kB
0x018FF -- 0x01100
Information memory
Size
Flash
256 Byte
0x010FF – 0x01000
Boot memory
Size
ROM
1 kB
0x0FFF – 0x0C00
Size
2 kB
0x009FF – 0x0200
16-bit
8-bit
8-bit SFR
0x001FF – 0x00100
0x000FF – 0x00010
0x0000F – 0x00000
Memory
Main: interrupt vector
Main: code memory
RAM (mirrored at 18FFh to 01100h)
Peripherals
Bootstrap Loader (BSL)
The MSP430 bootstrap loader (BSL) enables users to program the flash memory or RAM using a UART serial
interface. Access to the MSP430 memory via the BSL is protected by user-defined password. For complete
description of the features of the BSL and its implementation, see the application report, Features of the MSP430
Bootstrap Loader, TI literature number SLAA089.
BSL Function
PM Package Pins
Data Transmit
13 - P1.1
Data Receive
22 - P2.2
Flash Memory
The flash memory can be programmed via the JTAG port, the bootstrap loader or in-system by the CPU. The
CPU can perform single-byte and single-word writes to the flash memory. Features of the flash memory include:
• Flash memory has n segments of main memory and four segments of information memory (A to D) of 64
bytes each. Each segment in main memory is 512 bytes in size.
• Segments 0 to n may be erased in one step, or each segment may be individually erased.
• Segments A to D can be erased individually, or as a group with segments 0–n.
Segments A to D are also called information memory.
• Segment A contains calibration data. After reset segment A is protected against programming and erasing. It
can be unlocked but care should be taken not to erase this segment if the device-specific calibration data is
required.
• Flash content integrity check with marginal read modes.
Copyright © 2010–2011, Texas Instruments Incorporated
15
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Peripherals
Peripherals are connected to the CPU through data, address, and control busses and can be handled using all
instructions. For complete module descriptions, refer to the MSP430x2xx Family User's Guide (SLAU144).
DMA Controller
The DMA controller allows movement of data from one memory address to another without CPU intervention. For
example, the DMA controller can be used to move data from the ADC12 conversionmemory to RAM. Using the
DMA controller can increase the throughput of peripheral modules. The DMA controller reduces system power
consumption by allowing the CPU to remain in sleep mode without having to awaken to move data to or from a
peripheral.
Oscillator and System Clock
The clock system is supported by the basic clock module that includes support for a 32768-Hz watch crystal
oscillator, an internal very low power, low frequency oscillator and an internal digitally-controlled oscillator (DCO).
The basic clock module is designed to meet the requirements of both low system cost and low-power
consumption. The internal DCO provides a fast turn-on clock source and stabilizes in less than 1 μs. The basic
clock module provides the following clock signals:
• Auxiliary clock (ACLK), sourced either from a 32768-Hz watch crystal or the internal LF oscillator for –55°C to
105°C operation. For > 105°C, use external clock source.
• Main clock (MCLK), the system clock used by the CPU
• Sub-Main clock (SMCLK), the sub-system clock used by the peripheral modules
The DCO settings to calibrate the DCO output frequency are stored in the information memory segment A.
Table 4. Tags Used by the TLV Structure
NAME
ADDRESS
VALUE
DESCRIPTION
0x01
DCO frequency calibration at VCC = 3 V and TA = 25°C at
calibration
0x10DA
0x08
ADC12_1 calibration tag
--
0xFE
Identifier for empty areas
TAG_DCO_30
0x10F6
TAG_ADC12_1
TAG_EMPTY
Table 5. Labels Used by the ADC Calibration Structure
LABEL
SIZE
ADDRESS
OFFSET
CAL_ADC_25T85
INCHx = 0x1010; REF2_5 = 1, TA = 125°C
word
0x000E
CAL_ADC_25T30
INCHx = 0x1010; REF2_5 = 1, TA = 30°C
word
0x000C
REF2_5 = 1,TA = 30°C
word
0x000A
CAL_ADC_15T85
INCHx = 0x1010; REF2_5 = 0, TA = 125°C
word
0x0008
CAL_ADC_15T30
INCHx = 0x1010; REF2_5 = 0, TA = 30°C
word
0x0006
REF2_5 = 0,TA = 30°C
word
0x0004
External VREF = 1.5 V, fADC12CLK = 5 MHz
word
0x0002
External VREF = 1.5 , fADC12CLK = 5 MHz
word
0x0000
CAL_BC1_1MHZ
--
byte
0x0007
CAL_DCO_1MHZ
--
byte
0x0006
CAL_ADC_25VREF_FACTOR
CAL_ADC_15VREF_FACTOR
CAL_ADC_OFFSET
CAL_ADC_GAIN_FACTOR
16
CONDITION AT CALIBRATION/DESCRIPTION
CAL_BC1_8MHZ
--
byte
0x0005
CAL_DCO_8MHZ
--
byte
0x0004
CAL_BC1_12MHZ
--
byte
0x0003
CAL_DCO_12MHZ
--
byte
0x0002
CAL_BC1_16MHZ
--
byte
0x0001
CAL_DCO_16MHZ
--
byte
0x0000
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
www.ti.com
SLAS697B – MARCH 2010 – REVISED JUNE 2011
Brownout, Supply Voltage Supervisor (SVS)
The brownout circuit is implemented to provide the proper internal reset signal to the device during power on and
power off. The SVS circuitry detects if the supply voltage drops below a user selectable level and supports both
supply voltage supervision (the device is automatically reset) and supply voltage monitoring (SVM) (the device is
not automatically reset).
The CPU begins code execution after the brownout circuit releases the device reset. However, VCC may not have
ramped to VCC(min) at that time. The user must ensure that the default DCO settings are not changed until VCC
reaches VCC(min). If desired, the SVS circuit can be used to determine when VCC reaches VCC(min).
Digital I/O
There are six 8-bit I/O ports implemented – ports P1 through P6:
• All individual I/O bits are independently programmable.
• Any combination of input, output, and interrupt condition is possible.
• Edge-selectable interrupt input capability for all the eight bits of port P1 and P2.
• Read/write access to port-control registers is supported by all instructions.
• Each I/O has an individually programmable pullup/pulldown resistor.
WDT+ Watchdog Timer
The primary function of the watchdog timer (WDT+) module is to perform a controlled system restart after a
software problem occurs. If the selected time interval expires, a system reset is generated. If the watchdog
function is not needed in an application, the module can be disabled or configured as an interval timer and can
generate interrupts at selected time intervals.
Hardware Multiplier
The multiplication operation is supported by a dedicated peripheral module. The module performs 16 × 16,
16 × 8, 8 × 16, and 8 × 8 bit operations. The module is capable of supporting signed and unsignedmultiplication
as well as signed and unsignedmultiply and accumulate operations. The result of an operation can be accessed
immediately after the operands have been loaded into the peripheral registers. No additional clock cycles are
required.
USCI
The universal serial communication interface (USCI) module is used for serial data communication. The USCI
module supports synchronous communication protocols like SPI (3 or 4 pin), I2C and asynchronous
communication protocols like UART, enhanced UART with automatic baud-rate detection (LIN), and IrDA.
USCI_A0 provides support for SPI (3 or 4 pin), UART, enhanced UART and IrDA.
USCI_B0 provides support for SPI (3 or 4 pin) and I2C.
Copyright © 2010–2011, Texas Instruments Incorporated
17
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Timer_A3
Timer_A3 is a 16-bit timer/counter with three capture/compare registers. Timer_A3 can support multiple
capture/compares, PWM outputs, and interval timing. Timer_A3 also has extensive interrupt capabilities.
Interrupts may be generated from the counter on overflow conditions and from each of the capture/compare
registers.
Table 6. TIMER_A3 Signal Connections
INPUT PIN
NO.
DEVICE
INPUT
SIGNAL
MODULE
INPUT
NAME
12 - P1.0
TACLK
TACLK
ACLK
ACLK
SMCLK
SMCLK
21 - P2.1
TAINCLK
INCLK
13 - P1.1
TA0
CCI0A
22 - P2.2
TA0
CCI0B
14 - P1.2
MODULE
BLOCK
MODULE
U
SIGNAL
Timer
NA
OUTPUT PIN
NO.
13 - P1.1
CCR0
TA0
17 - P1.5
DVSS
GND
DVCC
VCC
TA1
CCI1A
14 - P1.2
CAOUT
(internal)
CCI1B
18 - P1.6
DVSS
GND
23 - P2.3
DVCC
VCC
CCR1
TA1
27 - P2.7
ADC12
(internal)
DAC12_0
(internal)
DAC12_1
(internal)
15 - P1.3
18
TA2
CCI2A
ACLK
(internal)
CCI2B
DVSS
GND
DVCC
VCC
15 - P1.3
CCR2
TA2
19 - P1.7
24 - P2.4
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Timer_B7
Timer_B7 is a 16-bit timer/counter with three capture/compare registers. Timer_B7 can support multiple
capture/compares, PWM outputs, and interval timing. Timer_B7 also has extensive interrupt capabilities.
Interrupts may be generated from the counter on overflow conditions and from each of the capture/compare
registers.
Timer_B7 Signal Connections
INPUT PIN
NO.
DEVICE
INPUT
SIGNAL
MODULE
INPUT
NAME
43 - P4.7
TBCLK
TBCLK
ACLK
ACLK
SMCLK
SMCLK
43 - P4.7
TBCLK
INCLK
36 - P4.0
TB0
CCI0A
36 - P4.0
TB0
CCI0B
DVSS
GND
DVCC
VCC
37 - P4.1
TB1
CCI1A
37 - P4.1
TB1
CCI1B
DVSS
GND
MODULE
BLOCK
MODULE
OUTPUT
SIGNAL
Timer
NA
OUTPUT
PIN NO.
36 - P4.0
CCR0
TB0
ADC12
(internal)
37 - P4.1
CCR1
TB1
ADC12
(internal)
DVCC
VCC
38 - P4.2
TB2
CCI2A
38 - P4.2
38 - P4.2
TB2
CCI2B
DAC_0
(internal)
DVSS
GND
CCR2
DVCC
VCC
39 - P4.3
TB3
CCI3A
39 - P4.3
TB3
CCI3B
DVSS
GND
40 - P4.4
40 - P4.4
41 - P4.5
41 - P4.5
42 - P4.6
DVCC
VCC
TB4
CCI4A
TB4
CCI4B
DVSS
GND
DVCC
VCC
TB5
CCI5A
TB5
CCI5B
DVSS
GND
DVCC
VCC
TB6
CCI6A
ACLK (internal)
CCI6B
DVSS
GND
DVCC
VCC
Copyright © 2010–2011, Texas Instruments Incorporated
TB2
DAC_1
(internal)
39 - P4.3
CCR3
TB3
40 - P4.4
CCR4
TB4
41 - P4.5
CCR5
TB5
42 - P4.6
CCR6
TB6
19
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Comparator_A+
The primary function of the comparator_A+ module is to support precision slope analog-to-digital conversions,
battery-voltage supervision, and monitoring of external analog signals.
ADC12
The ADC12 module supports fast 12-bit analog-to-digital conversions. The module implements a 12-bit SAR
core, sample select control, reference generator, and a 16-word conversion-and-control buffer. The
conversion-and-control buffer allows up to 16 independent ADC samples to be converted and stored without any
CPU intervention.
DAC12
The DAC12 module is a 12-bit, R-ladder, voltage-output digital-to-analog converter (DAC). The DAC12 may be
used in 8-bit or 12-bit mode and may be used in conjunction with the DMA controller. When multiple DAC12
modules are present, they may be grouped together for synchronous operation.
20
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Peripheral File Map
DMA
DMA channel 2 transfer size
DMA2SZ
0x01F2
DMA channel 2 destination address
DMA2DA
0x01EE
DMA channel 2 source address
DMA2SA
0x01EA
DMA channel 2 control
DMA2CTL
0x01E8
DMA channel 1 transfer size
DMA1SZ
0x01E6
DMA channel 1 destination address
DMA1DA
0x01E2
DMA channel 1 source address
DMA1SA
0x01DE
DMA channel 1 control
DMA1CTL
0x01DC
DMA channel 0 transfer size
DMA0SZ
0x01DA
DMA channel 0 destination address
DMA0DA
0x01D6
DMA channel 0 source address
DMA0SA
0x01D2
DMA channel 0 control
DMA0CTL
0x01D0
DMAIV
0x0126
DMA module control 1
DMACTL1
0x0124
DMA module control 0
DMACTL0
0x0122
DAC12_1 data
DAC12_1DAT
0x01CA
DAC12_1 control
DAC12_1CTL
0x01C2
DAC12_0 data
DAC12_0DAT
0x01C8
DAC12_0 control
DAC12_0CTL
0x01C0
DMA module interrupt vector word
DAC12
Copyright © 2010–2011, Texas Instruments Incorporated
21
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
ADC12
www.ti.com
Interrupt-vector-word register
ADC12IV
0x01A8
Inerrupt-enable register
ADC12IE
0x01A6
Inerrupt-flag register
22
ADC12IFG
0x01A4
Control register 1
ADC12CTL1
0x01A2
Control register 0
ADC12CTL0
0x01A0
Conversion memory 15
ADC12MEM15
0x015E
Conversion memory 14
ADC12MEM14
0x015C
Conversion memory 13
ADC12MEM13
0x015A
Conversion memory 12
ADC12MEM12
0x0158
Conversion memory 11
ADC12MEM11
0x0156
Conversion memory 10
ADC12MEM10
0x0154
Conversion memory 9
ADC12MEM9
0x0152
Conversion memory 8
ADC12MEM8
0x0150
Conversion memory 7
ADC12MEM7
0x014E
Conversion memory 6
ADC12MEM6
0x014C
Conversion memory 5
ADC12MEM5
0x014A
Conversion memory 4
ADC12MEM4
0x0148
Conversion memory 3
ADC12MEM3
0x0146
Conversion memory 2
ADC12MEM2
0x0144
Conversion memory 1
ADC12MEM1
0x0142
Conversion 0
ADC12MEM0
0x0140
ADC memory-control register15
ADC12MCTL15
0x008F
ADC memory-control register14
ADC12MCTL14
0x008E
ADC memory-control register13
ADC12MCTL13
0x008D
ADC memory-control register12
ADC12MCTL12
0x008C
ADC memory-control register11
ADC12MCTL11
0x008B
ADC memory-control register10
ADC12MCTL10
0x008A
ADC memory-control register9
ADC12MCTL9
0x0089
ADC memory-control register8
ADC12MCTL8
0x0088
ADC memory-control register7
ADC12MCTL7
0x0087
ADC memory-control register6
ADC12MCTL6
0x0086
ADC memory-control register5
ADC12MCTL5
0x0085
ADC memory-control register4
ADC12MCTL4
0x0084
ADC memory-control register3
ADC12MCTL3
0x0083
ADC memory-control register2
ADC12MCTL2
0x0082
ADC memory-control register1
ADC12MCTL1
0x0081
ADC memory-control register0
ADC12MCTL0
0x0080
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Timer_B7
Capture/compare register _ 6
TBCCR6
0x019E
Capture/compare register 5
TBCCR5
0x019C
Capture/compare register 4
TBCCR4
0x019A
Capture/compare register 3
TBCCR3
0x0198
Capture/compare register 2
TBCCR2
0x0196
Capture/compare register 1
TBCCR1
0x0194
Capture/compare register 0
TBCCR0
0x0192
Timer_B register
TBR
0x0190
Capture/compare control 6
TBCCTL6
0x018E
Capture/compare control 5
TBCCTL5
0x018C
Capture/compare control 4
TBCCTL4
0x018A
Capture/compare control 3
TBCCTL3
0x0188
Capture/compare control 2
TBCCTL2
0x0186
Capture/compare control 1
TBCCTL1
0x0184
Capture/compare control 0
TBCCTL0
0x0182
TBCTL
0x0180
Timer_B control
Timer_B interrupt vector
Timer_A3
TBIV
0x011E
Capture/compare register 2
TACCR2
0x0176
Capture/compare register 1
TACCR1
0x0174
Capture/compare register 0
TACCR0
0x0172
Timer_A register
TAR
0x016E
Reserved
0x016C
Reserved
0x016A
Reserved
TACCTL2
0x0166
Capture/compare control 1
TACCTL1
0x0164
Capture/compare control 0
TACCTL0
0x0162
TACTL
0x0160
TAIV
0x012E
Timer_A interrupt vector
Sum extend
SUMEXT
0x013E
Result high word
RESHI
0x013C
Result low word
RESLO
0x013A
Second operand
OP2
0x0138
MACS
0x0136
MAC
0x0134
MPYS
0x0132
Multiply signed +accumulate/operand1
Multiply+accumulate/operand1
Multiply signed/operand1
Multiply unsigned/operand1
Flash
Watchdog
0x0168
Capture/compare control 2
Timer_A control
Hardware Multiplier
0x0170
Reserved
MPY
0x0130
Flash control 4
FCTL4
0x01BE
Flash control 3
FCTL3
0x012C
Flash control 2
FCTL2
0x012A
Flash control 1
FCTL1
0x0128
WDTCTL
0x0120
Watchdog/timer control
Copyright © 2010–2011, Texas Instruments Incorporated
23
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
USCI A0/B0
www.ti.com
USCI A0 auto baud rate control
UCA0ABCTL
0x005D
USCI A0 transmit buffer
UCA0TXBUF
0x0067
USCI A0 receive buffer
UCA0RXBUF
0x0066
USCI A0 status
UCA0STAT
0x0065
USCI A0 modulation control
UCA0MCTL
0x0064
USCI A0 baud rate control 1
UCA0BR1
0x0063
USCI A0 baud rate control 0
UCA0BR0
0x0062
USCI A0 control 1
UCA0CTL1
0x0061
USCI A0 control 0
UCA0CTL0
0x0060
USCI A0 IrDA receive control
UCA0IRRCTL
0x005F
USCI A0 IrDA transmit control
UCA0IRTCLT
0x005E
USCI B0 transmit buffer
UCB0TXBUF
0x006F
USCI B0 receive buffer
UCB0RXBUF
0x006E
UCB0STAT
0x006D
USCI B0 I2C interrupt enable
UCB0CIE
0x006C
USCI B0 baud rate control 1
UCB0BR1
0x006B
USCI B0 baud rate control 0
UCB0BR0
0x006A
USCI B0 control 1
UCB0CTL1
0x0069
USCI B0 control 0
UCB0CTL0
0x0068
USCI B0 I C slave address
UCB0SA
0x011A
USCI B0 I2C own address
UCB0OA
0x0118
UCA1ABCTL
0x00CD
USCI A1 transmit buffer
UCA1TXBUF
0x00D7
USCI A1 receive buffer
UCA1RXBUF
0x00D6
USCI A1 status
UCA1STAT
0x00D5
USCI A1 modulation control
UCA1MCTL
0x00D4
USCI A1 baud rate control 1
UCA1BR1
0x00D3
USCI A1 baud rate control 0
UCA1BR0
0x00D2
USCI A1 control 1
UCA1CTL1
0x00D1
USCI B0 status
2
USCI A1/B1
USCI A1 auto baud rate control
USCI A1 control 0
UCA1CTL0
0x00D0
USCI A1 IrDA receive control
UCA1IRRCTL
0x00CF
USCI A1 IrDA transmit control
UCA1IRTCLT
0x00CE
USCI B1 transmit buffer
UCB1TXBUF
0x00DF
USCI B1 receive buffer
UCB1RXBUF
0x00DE
USCI B1 status
UCB1STAT
0x00DD
USCI B1 I2C Interrupt enable
UCB1CIE
0x00DC
USCI B1 baud rate control 1
UCB1BR1
0x00DB
USCI B1 baud rate control 0
UCB1BR0
0x00DA
USCI B1 control 1
UCB1CTL1
0x00D9
USCI B1 control 0
UCB1CTL0
0x00D8
USCI B1 I2C slave address
UCB1SA
0x017E
USCI B1 I2C own address
UCB1OA
0x017C
UC1IE
0x0006
USCI A1/B1 interrupt enable
USCI A1/B1 interrupt flag
Comparator_A+
24
UC1IFG
0x0007
CAPD
0x005B
Comparator_A control2
CACTL2
0x005A
Comparator_A control1
CACTL1
0x0059
Comparator_A port disable
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Basic Clock
Basic clock system control3
BCSCTL3
0x0053
Basic clock system control2
BCSCTL2
0x0058
Basic clock system control1
BCSCTL1
0x0057
DCO clock frequency control
DCOCTL
0x0056
Brownout, SVS
SVS control register (reset by brownout signal)
SVSCTL
0x0055
Port P6
Port P6 resistor enable
P6REN
0x0013
Port P6 selection
P6SEL
0x0037
Port P6 direction
P6DIR
0x0036
Port P6 output
P6OUT
0x0035
Port P6 input
Port P5
P6IN
0x0034
Port P5 resistor enable
P5REN
0x0012
Port P5 selection
P5SEL
0x0033
Port P5 direction
P5DIR
0x0032
Port P5 output
P5OUT
0x0031
Port P5 input
Port P4
P5IN
0x0030
Port P4 selection
P4SEL
0x001F
Port P4 resistor enable
P4REN
0x0011
Port P4 direction
P4DIR
0x001E
Port P4 output
P4OUT
0x001D
P4IN
0x001C
Port P4 input
Port P3
Port P3 resistor enable
P3REN
0x0010
Port P3 selection
P3SEL
0x001B
Port P3 direction
P3DIR
0x001A
Port P3 output
P3OUT
0x0019
Port P3 input
Port P2
P3IN
0x0018
Port P2 resistor enable
P2REN
0x002F
Port P2 selection
P2SEL
0x002E
P2IE
0x002D
P2IES
0x002C
Port P2 interrupt flag
P2IFG
0x002B
Port P2 direction
P2DIR
0x002A
Port P2 output
P2OUT
0x0029
Port P2 interrupt enable
Port P2 interrupt-edge select
Port P2 input
Port P1
P2IN
0x0028
Port P1 resistor enable
P1REN
0x0027
Port P1 selection
P1SEL
0x0026
P1IE
0x0025
Port P1 interrupt-edge select
P1IES
0x0024
Port P1 interrupt flag
P1IFG
0x0023
Port P1 direction
P1DIR
0x0022
Port P1 output
Port P1 interrupt enable
Special Functions
P1OUT
0x0021
Port P1 input
P1IN
0x0020
SFR interrupt flag2
IFG2
0x0003
SFR interrupt flag1
IFG1
0x0002
SFR interrupt enable2
IE2
0x0001
SFR interrupt enable1
IE1
0x0000
Copyright © 2010–2011, Texas Instruments Incorporated
25
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Absolute Maximum Ratings (1)
VALUE
UNIT
Voltage applied at VCC to VSS
–0.3 to 4.1
V
Voltage applied to any pin (2)
–0.3 to VCC + 0.3
V
±2
mA
–55 to 150
°C
–55 to 150
°C
Diode current at any device terminal
Storage temperature, Tstg (unprogrammed device (3))
Storage temperature, Tstg (programmed device
(1)
(3)
)
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages referenced to VSS. The JTAG fuse-blow voltage, VFB, is allowed to exceed the absolute maximum rating. The voltage is
applied to the TEST pin when blowing the JTAG fuse.
Higher temperature may be applied during board soldering process according to the current JEDEC J-STD-020 specification with peak
reflow temperatures not higher than classified on the device label on the shipping boxes or reels.
(2)
(3)
Recommended Operating Conditions (1)
(2)
MIN
Supply voltage during program execution
2.2
3.6
V
–55
150
°C
VCC = 2.2 V, Duty Cycle = 50% ±10%
dc
10
VCC = 2.7 V, Duty Cycle = 50% ±10%
dc
12
VCC ≥ 3.3 V, Duty Cycle = 50% ±10%
dc
16
AVCC = DVCC = VCC (3)
VSS
Supply voltage
AVSS = DVSS = VSS
TA
Operating free-air temperature range
(1)
(2)
(3)
UNIT
V
Supply voltage during flash memory
programming
(2)
MAX
3.6
VCC
Processor frequency fSYSTEM
(Maximum MCLK frequency) (1)
(see Figure 1)
NOM
1.8
0
V
MHz
The MSP430 CPU is clocked directly with MCLK. Both the high and low phase of MCLK must not exceed the pulse width of the
specified maximum frequency.
Modules might have a different maximum input clock specification. Refer to the specification of the respective module in this data sheet.
It is recommended to power AVCC and DVCC from the same source. A maximum difference of 0.3 V between AVCC and DVCC can be
tolerated during power-up.
System Frequency −MHz
16 MHz
12 MHz
7.5 MHz
4.15 MHz
1.8 V
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
2.2 V
2.7 V
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
Legend:
Supply voltage range,
during flash memory
programming
Supply voltage range,
during program execution
3.3 V 3.6 V
Supply Voltage −V
NOTE: Minimum processor frequency is defined by system clock. Flash program or erase operations require a minimum VCC
of 2.2 V.
Figure 1. Operating Area
26
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Figure 2. Operating Life Curve
Copyright © 2010–2011, Texas Instruments Incorporated
27
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Active-Mode Supply Current Into AVCC Excluding External Current –
Electrical Characteristics (1) (2)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
IAM,
IAM,
IAM,
1MHz
1MHz
4kHz
TEST CONDITIONS
fDCO = fMCLK = fSMCLK = 1 MHz,
fACLK = 32,768 Hz,
Program executes in flash,
Active-mode (AM)
BCSCTL1 = CALBC1_1 MHZ,
current (1 MHz)
DCOCTL = CALDCO_1 MHZ,
CPUOFF = 0, SCG0 = 0, SCG1 = 0,
OSCOFF = 0
fDCO = fMCLK = fSMCLK = 1 MHz,
fACLK = 32,768 Hz,
Program executes in RAM,
Active-mode (AM)
BCSCTL1 = CALBC1_1 MHZ,
current (1 MHz)
DCOCTL = CALDCO_1 MHZ,
CPUOFF = 0, SCG0 = 0, SCG1 = 0,
OSCOFF = 0
fMCLK = fSMCLK = fACLK = 32,768 Hz/8 =
4,096 Hz,
fDCO = 0 Hz,
Active-mode (AM) Program executes in flash,
current (4 kHz)
SELMx = 11, SELS = 1,
DIVMx = DIVSx = DIVAx = 11,
CPUOFF = 0, SCG0 = 1, SCG1 = 0,
OSCOFF = 0
TA
VCC
MIN
–55°C to 85°C
105°C
2.2 V
IAM,
100kHz
28
395
375
420
640
–55°C to 85°C
515
560
525
595
105°C
3V
150°C
105°C
2.2 V
330
370
340
390
150°C
660
–55°C to 85°C
460
495
470
520
105°C
3V
150°C
–55°C to 85°C
105°C
105°C
2.2 V
3V
2.2 V
2.1
9
15
31
3
11
19
32
67
86
80
99
150°C
190
–55°C to 85°C
84
107
99
128
105°C
μA
μA
710
–55°C to 85°C
105°C
UNIT
700
–55°C to 85°C
3V
150°C
(1)
(2)
365
150°C
–55°C to 85°C
fMCLK = fSMCLK = fDCO(0, 0) ≉ 100 kHz,
fACLK = 0 Hz,
Active-mode (AM) Program executes in flash,
current (100 kHz) RSELx = 0, DCOx = 0,
CPUOFF = 0, SCG0 = 0, SCG1 = 0,
OSCOFF = 1
TYP MAX
μA
μA
240
All inputs are tied to 0 V or VCC. Outputs do not source or sink any current.
The currents are characterized with a Micro Crystal CC4V-T1A SMD crystal with a load capacitance of 9 pF.
The internal and external load capacitance is chosen to closely match the required 9 pF.
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Typical Characteristics – Active-Mode Supply Current (Into DVCC + AVCC)
Figure 3. Active-Mode Current vs VCC, TA = 25°C
Figure 4. Active-Mode Current vs DCO Frequency
Active-Mode Current vs DCO Frequency
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
fSMCLK = fDCO = 1 MHz
2.2 V
0.38
150°C
0.42
–55°C
0.50
mA
0.49
3V
0.51
125°C
0.55
150°C
0.60
–55°C
3.71
–40°C
3.73
2.2 V
3.79
125°C
4.45
150°C
4.60
–55°C
5.47
–40°C
25°C
UNIT
0.36
125°C
25°C
Copyright © 2010–2011, Texas Instruments Incorporated
MAX
0.30
25°C
fSMCLK = fDCO = 12 MHz
TYP
–40°C
–40°C
Active Mode Current Supply
MIN
0.35
25°C
Active Mode Current Supply
VCC
–55°C
mA
5.49
3V
5.54
125°C
5.68
150°C
5.77
29
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Active-Mode Current vs DCO Frequency (continued)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
VCC
MIN
TYP
MAX
–55°C
5.46
–40°C
5.58
25°C
Active Mode Current Supply
fSMCLK = fDCO = 16 MHz
UNIT
2.2 V
5.89
125°C
6.03
150°C
6.20
–55°C
7.14
–40°C
7.14
25°C
3V
mA
7.21
125°C
7.429
150°C
7.54
Low-Power-Mode Supply Currents Into AVCC Excluding External Current – Electrical
Characteristics (1) (2)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
ILPM0, 1MHz
Low-power mode 0
(LPM0) current (3)
TEST CONDITIONS
fMCLK = 0 MHz,
fSMCLK = fDCO = 1 MHz,
fACLK = 32,768 Hz,
BCSCTL1 = CALBC1_1 MHZ,
DCOCTL = CALDCO_1 MHZ,
CPUOFF = 1, SCG0 = 0, SCG1 = 0,
OSCOFF = 0
TA
VCC
MIN
–55°C to 85°C
105°C
2.2 V
ILPM0, 100kHz
ILPM2
Low-power mode 0
(LPM0) current (3)
Low-power mode 2
(LPM2) current (4)
fMCLK = fSMCLK = 0 MHz, fDCO = 1 MHz,
fACLK = 32,768 Hz,
BCSCTL1 = CALBC1_1 MHZ,
DCOCTL = CALDCO_1 MHZ,
CPUOFF = 1, SCG0 = 0, SCG1 = 1,
OSCOFF = 0
ILPM3,LFXT1
Low-power mode 3
(LPM3) current (4)
30
98
87
105
100
125
105°C
3V
150°C
105°C
2.2 V
37
49
50
62
150°C
160
–55°C to 85°C
40
55
57
73
105°C
3V
150°C
185
–55°C to 85°C
23
33
35
46
105°C
2.2 V
150°C
148
–55°C to 85°C
25
36
40
55
105°C
3V
150°C
168
–55°C
0.8
1.2
1
1.3
85°C
2.2 V
4.6
7
105°C
14
24
–55°C
0.9
1.3
1.1
1.5
25°C
UNIT
μA
240
3V
105°C
(3)
(4)
83
–55°C to 85°C
85°C
(1)
(2)
83
210
25°C
fDCO = fMCLK = fSMCLK = 0 MHz,
fACLK = 32,768 Hz,
CPUOFF = 1, SCG0 = 1, SCG1 = 1,
OSCOFF = 0
68
150°C
–55°C to 85°C
fMCLK = 0 MHz,
fSMCLK = fDCO(0, 0) ≉ 100 kHz,
fACLK = 0 Hz,
RSELx = 0, DCOx = 0,
CPUOFF = 1, SCG0 = 0, SCG1 = 0,
OSCOFF = 1
TYP MAX
5.5
8
17
30
μA
μA
μA
All inputs are tied to 0 V or VCC. Outputs do not source or sink any current.
The currents are characterized with a Micro Crystal CC4V-T1A SMD crystal with a load capacitance of 9 pF.
The internal and external load capacitance is chosen to closely match the required 9 pF.
Current for brownout and WDT clocked by SMCLK included.
Current for brownout and WDT clocked by ACLK included.
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Low-Power-Mode Supply Currents Into AVCC Excluding External Current – Electrical
Characteristics(1) (2) (continued)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
VCC
–55°C
1
4.3
6.5
105°C
14
24
150°C
125
Low-power mode 3
current, (LPM3) (4)
–55°C
0.6
1.2
0.6
1.2
5
7.5
105°C
16.5
29.5
150°C
130
–55°C
0.1
0.5
0.1
0.5
2.2 V
25°C
85°C
3V
25°C
85°C
ILPM4
Low-power mode 4
(LPM4) current (5)
fDCO = fMCLK = fSMCLK = 0 MHz,
fACLK = 0 Hz,
CPUOFF = 1, SCG0 = 1, SCG1 = 1,
OSCOFF = 1
2.2 V
4
6
105°C
13
23
150°C
125
–55°C
0.2
0.5
0.2
0.5
4.7
7
105°C
14
24
150°C
146
25°C
85°C
(5)
3V
UNIT
1
0.5
85°C
ILPM3,VLO
TYP MAX
0.4
25°C
fDCO = fMCLK = fSMCLK = 0 MHz,
fACLK from internal LF oscillator (VLO),
CPUOFF = 1, SCG0 = 1, SCG1 = 1,
OSCOFF = 0
MIN
μA
μA
Current for brownout included.
ILPM4 - Low-Power Mode Current - mA
Typical Characteristics – LPM4 Current
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
–40
VCC = 3.6 V
VCC = 30 V
VCC = 2.2 V
VCC = 1.8 V
–20
0
20
40
60
80
100
120
TA - Temperature - °C
Figure 5. ILPM4 -- LPM4 Current vs Temperature
Copyright © 2010–2011, Texas Instruments Incorporated
31
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Schmitt-Trigger Inputs (Ports P1 Through P6, and RST/NMI, JTAG, XIN, and XT2IN) (1) –
Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
VIT+
TEST CONDITIONS
Positive-going input threshold voltage
VCC
MIN
2.2 V
3V
VIT–
Negative-going input threshold voltage
Vhys
Input voltage hysteresis (VIT+ – VIT–)
RPull
Pullup/pulldown resistor
For pullup: VIN = VSS;
For pulldown:
VIN = VCC
CI
Input capacitance
VIN = VSS or VCC
(1)
TYP
MAX
0.45 x
VCC
0.75 x
VCC
1.00
1.65
1.35
2.25
0.25 x
VCC
0.55 x
VCC
2.2 V
0.55
1.20
3V
0.75
1.65
2.2 V
0.2
1
3V
0.3
1
20
35
50
5
UNIT
V
V
V
kΩ
pF
XIN and XT2IN in bypass mode only.
Inputs (Ports P1 and P2) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
t(int)
(1)
External interrupt timing
TEST CONDITIONS
VCC
Port P1, P2: P1.x to P2.x, External trigger pulse
width to set interrupt flag (1)
2.2 V/3 V
MIN
MAX
20
UNIT
ns
An external signal sets the interrupt flag every time the minimum interrupt pulse width t(int) is met. It may be set even with trigger signals
shorter than t(int).
Leakage Current (Ports P1 Through P6) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
Ilkg(Px.x)
(1)
(2)
High-impedance leakage
current
TEST CONDITIONS
See
(1)
and
(2)
VCC
MIN
TYP
MAX
±250
2.2 V/3 V
UNIT
nA
The leakage current is measured with VSS or VCC applied to the corresponding pin(s), unless otherwise noted.
The leakage of the digital port pins is measured individually. The port pin is selected for input and the pullup/pulldown resistor is
disabled.
Standard Inputs - RST/NMI – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
MIN
MAX
UNIT
VIL
Low-level input voltage
2.2 V/3 V
VSS
VSS + 0.6
V
VIH
High-level input voltage
2.2 V/3 V
0.8 x VCC
VCC
V
32
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Outputs (Ports P1 Through P6) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
IOH(max) = –1.5 mA
VOH
High-level output voltage
VCC
(1)
2.2 V
(2)
IOH(max) = –6 mA
IOH(max) = –1.5 mA (1)
3V
IOH(max) = –6 mA (2)
IOL(max) = 1.5 mA
VOL
Low-level output voltage
(2)
MAX
VCC – 0.25
VCC
VCC – 0.6
VCC
VCC – 0.25
VCC
VCC – 0.6
VCC
VSS
VSS+0.25
(1)
2.2 V
IOL(max) = 6 mA (2)
IOL(max) = 1.5 mA (1)
3V
IOL(max) = 6 mA (2)
(1)
MIN
VSS
VSS+0.6
VSS
VSS+0.25
VSS
VSS+0.6
UNIT
V
V
The maximum total current, IOH(max) and IOL(max), for all outputs combined, should not exceed ±12 mA to hold the maximum voltage drop
specified.
The maximum total current, IOH(max) and IOL(max), for all outputs combined, should not exceed ±48 mA to hold the maximum voltage drop
specified.
Output Frequency (Ports P1 Through P6) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
fPx.y
Port output frequency
(with load)
P1.4/SMCLK, CL = 20 pF, RL = 1 kΩ (1)
fPort_CLK
Clock output
frequency
P2.0/ACLK/CA2, P1.4/SMCLK, CL = 20 pF (2)
t(Xdc)
Duty cycle of output
frequency
MIN
TYP
MAX
2.2 V
DC
10
3V
DC
12
2.2 V
DC
12
3V
DC
16
P5.6/ACLK, CL = 20 pF, LF mode
30
50
70
P5.6/ACLK, CL = 20 pF, XT1 mode
40
50
60
P5.4/MCLK, CL = 20 pF, XT1 mode
40
60
50-15 ns
50 50+15 ns
P5.4/MCLK, CL = 20 pF, DCO
P1.4/SMCLK, CL = 20 pF, XT2 mode
P1.4/SMCLK, CL = 20 pF, DCO
(1)
(2)
(2)
VCC
40
60
50-15 ns
50+15 ns
UNIT
MHz
MHz
%
A resistive divider with 2 times 0.5 kΩ between VCC and VSS is used as load. The output is connected to the center tap of the divider.
The output voltage reaches at least 10% and 90% VCC at the specified toggle frequency.
Copyright © 2010–2011, Texas Instruments Incorporated
33
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Typical Characteristics – Outputs
TYPICAL LOW-LEVEL OUTPUT CURRENT
vs
LOW-LEVEL OUTPUT VOLTAGE
TYPICAL LOW-LEVEL OUTPUT CURRENT
vs
LOW-LEVEL OUTPUT VOLTAGE
50.0
VCC = 2.2 V
P4.5
TA = 25°C
20.0
I OL − Typical Low-Level Output Current − mA
I OL − Typical Low-Level Output Current − mA
25.0
TA = 85°C
15.0
10.0
5.0
0.0
0.0
0.5
1.0
1.5
2.0
VCC = 3 V
P4.5
40.0
TA = 85°C
30.0
20.0
10.0
0.0
0.0
2.5
TA = 25°C
VOL − Low-Level Output Voltage − V
0.5
1.0
Figure 6.
I OH − Typical High-Level Output Current − mA
I OH − Typical High-Level Output Current − mA
3.0
3.5
0.0
VCC = 2.2 V
P4.5
−5.0
−10.0
−15.0
TA = 85°C
TA = 25°C
0.5
1.0
1.5
2.0
VOH − High-Level Output Voltage − V
Figure 8.
34
2.5
TYPICAL HIGH-LEVEL OUTPUT CURRENT
vs
HIGH-LEVEL OUTPUT VOLTAGE
0.0
−25.0
0.0
2.0
Figure 7.
TYPICAL HIGH-LEVEL OUTPUT CURRENT
vs
HIGH-LEVEL OUTPUT VOLTAGE
−20.0
1.5
VOL − Low-Level Output Voltage − V
2.5
VCC = 3 V
P4.5
−10.0
−20.0
−30.0
TA = 85°C
−40.0
−50.0
0.0
TA = 25°C
0.5
1.0
1.5
2.0
2.5
3.0
3.5
VOH − High-Level Output Voltage − V
Figure 9.
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
POR/Brownout Reset (BOR) – Electrical Characteristics (1)
(2)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC(start)
See Figure 10
dVCC/dt ≤ 3 V/s
V(B_IT–)
See Figure 10 through Figure 12
dVCC/dt ≤ 3 V/s
Vhys(B_IT–)
See Figure 10
dVCC/dt ≤ 3 V/s
td(BOR)
See Figure 10
t(reset)
Pulse length needed at RST/NMI pin to
accepted reset internally
(1)
(2)
VCC
MIN
TYP
MAX
0.7 ×
V(B_IT–)
70
2.2 V/3 V
2
130
UNIT
V
1.71
V
210
mV
2000
μs
μs
The current consumption of the brownout module is already included in the ICC current consumption data. The voltage level V(B_IT–) +
Vhys(B_IT–
) is ≤ 1.8 V.
During power up, the CPU begins code execution following a period of td(BOR) after VCC = V(B_IT–) + Vhys(B_IT–). The default DCO settings
must not be changed until VCC ≥ VCC(min), where VCC(min) is the minimum supply voltage for the desired operating frequency.
VCC
Vhys(B_IT−)
V(B_IT−)
VCC(start)
1
0
t d(BOR)
Figure 10. POR/Brownout Reset (BOR) vs Supply Voltage
Copyright © 2010–2011, Texas Instruments Incorporated
35
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Typical Characteristics - POR/Brownout Reset (BOR)
VCC
3V
2
VCC(drop) − V
VCC = 3 V
Typical Conditions
t pw
1.5
1
VCC(drop)
0.5
0
0.001
1
1000
1 ns
tpw − Pulse Width − µs
1 ns
tpw − Pulse Width − µs
Figure 11. VCC(drop) Level With a Square Voltage Drop to Generate a POR/Brownout Signal
VCC
2
t pw
3V
VCC(drop) − V
VCC = 3 V
1.5
Typical Conditions
1
VCC(drop)
0.5
tf = tr
0
0.001
1
1000
tf
tr
tpw − Pulse Width − µs
tpw − Pulse Width − µs
Figure 12. VCC(drop) Level With a Triangle Voltage Drop to Generate a POR/Brownout Signal
SVS (Supply Voltage Supervisor/Monitor) - Electrical Characteristics
over operating free-air temperature range (unless otherwise noted)
PARAMETER
t(SVSR)
TEST CONDITIONS
MIN
dVCC/dt > 30 V/ms (See Figure 13)
SVSON, switch from VLD = 0 to VLD ≠ 0, VCC = 3 V
tsettle
VLD ≠ 0 (See
V(SVSstart)
VLD ≠ 0, VCC/dt ≤ 3 V/s (See Figure 13)
2000
20
)
1.55
VLD = 1
Vhys(SVS_IT-)
VCC/dt ≤ 3 V/s (See Figure 13),
External voltage applied on A7
36
VLD = 2 to 14
VLD = 15
70
120
UNIT
μs
μs
150
(1)
VCC/dt ≤ 3 V/s (See Figure 13)
MAX
150
dVCC/dt ≤ 30 V/ms
td(SVSon)
(1)
TYP
5
12
μs
1.7
V
210
mV
V(SVS_IT-) ×
0.004
V(SVS_IT-) ×
0.016
4.4
20
V
mV
tsettle is the settling time that the comparator o/p needs to have a stable level after VLD is switched VLD ≠ 0 to a different VLD value
between 2 and 15. The overdrive is assumed to be > 50 mV.
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
SVS (Supply Voltage Supervisor/Monitor) - Electrical Characteristics (continued)
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC/dt ≤ 3 V/s (See Figure 13 and Figure 14)
V(SVS_IT-)
VCC/dt ≤ 3 V/s (See Figure 13 and Figure 14),
External voltage applied on A7
ICC(SVS)
(2)
(3)
(3)
MIN
TYP
MAX
VLD = 1
1.8
1.9
2.05
VLD = 2
1.94
2.1
2.25
VLD = 3
2.05
2.2
2.37
VLD = 4
2.14
2.3
2.48
VLD = 5
2.24
2.4
2.6
VLD = 6
2.33
2.5
2.71
VLD = 7
2.46
2.65
2.86
VLD = 8
2.58
2.8
3
VLD = 9
2.69
2.9
3.13
VLD = 10
2.83
3.05
3.29
VLD = 11
2.94
3.2
3.42
VLD = 12
3.11
3.35
3.61 (2)
VLD = 13
3.24
3.5
3.76 (2)
VLD = 14
3.43
3.7 (2)
3.99 (2)
VLD = 15
1.1
1.2
1.3
10
15
VLD ≠ 0, VCC = 2.2 V/3 V
UNIT
V
μA
The recommended operating voltage range is limited to 3.6 V.
The current consumption of the SVS module is not included in the ICC current consumption data.
Typical Characteristics - SVS
AVCC
V(SVS_IT-)
Software sets VLD > 0:
SVS is active
Vhys(SVS_IT-)
V(SVSstart)
V(B_IT-)
Vhys(B_IT-)
VCC(start)
Brownout
Brownout
Region
1
0
SVS out
td(BOR)
td(BOR)
SVS circuit is active from VLD > VCC < V(B_IT-)
1
0
td(SVSon)
td(SVSR)
Set POR
1
undefined
0
Figure 13. SVS Reset (SVSR) vs Supply Voltage
Copyright © 2010–2011, Texas Instruments Incorporated
37
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
VCC
tpw
3V
2
Rectangular Drop
VCC(min)
1.5
VCC(min) - V
Triangular Drop
1
1 ns
1 ns
VCC
0.5
tpw
3V
0
1
10
100
1000
tpw - Pulse Width - ms
VCC(min)
tf = tr
tf
tr
Figure 14. VCC(min): Square Voltage Drop and Triangle Voltage Drop to Generate an SVS Signal (VLD = 1)
38
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Main DCO Characteristics
•
•
•
All ranges selected by RSELx overlap with RSELx + 1: RSELx = 0 overlaps RSELx = 1, ... RSELx = 14
overlaps RSELx = 15.
DCO control bits DCOx have a step size as defined by parameter SDCO.
Modulation control bits MODx select how often fDCO(RSEL,DCO+1) is used within the period of 32 DCOCLK
cycles. The frequency fDCO(RSEL,DCO) is used for the remaining cycles. The frequency is an average equal to:
32 f DCO(RSEL,DCO) f DCO(RSEL,DCO ) 1)
f average +
MOD f DCO(RSEL,DCO) ) (32 * MOD) f DCO(RSEL,DCO ) 1)
(1)
DCO Frequency – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
VCC
Supply voltage range
TEST CONDITIONS
VCC
MIN
TYP
MAX
RSELx < 14
1.8
3.6
RSELx = 14
2.2
3.6
RSELx = 15
3.0
3.6
UNIT
V
fDCO(0,0)
DCO frequency (0, 0)
RSELx = 0, DCOx = 0,
MODx = 0
fDCO(0,3)
DCO frequency (0, 3)
RSELx = 0, DCOx = 3,
MODx = 0
2.2 V/3 V
0.07
0.17
MHz
fDCO(1,3)
DCO frequency (1, 3)
RSELx = 1, DCOx = 3,
MODx = 0
2.2 V/3 V
0.10
0.20
MHz
fDCO(2,3)
DCO frequency (2, 3)
RSELx = 2, DCOx = 3,
MODx = 0
2.2 V/3 V
0.14
0.28
MHz
fDCO(3,3)
DCO frequency (3, 3)
RSELx = 3, DCOx = 3,
MODx = 0
2.2 V/3 V
0.20
0.40
MHz
fDCO(4,3)
DCO frequency (4, 3)
RSELx = 4, DCOx = 3,
MODx = 0
2.2 V/3 V
0.28
0.54
MHz
fDCO(5,3)
DCO frequency (5, 3)
RSELx = 5, DCOx = 3,
MODx = 0
2.2 V/3 V
0.39
0.77
MHz
fDCO(6,3)
DCO frequency (6, 3)
RSELx = 6, DCOx = 3,
MODx = 0
2.2 V/3 V
0.54
1.06
MHz
fDCO(7,3)
DCO frequency (7, 3)
RSELx = 7, DCOx = 3,
MODx = 0
2.2 V/3 V
0.80
1.50
MHz
fDCO(8,3)
DCO frequency (8, 3)
RSELx = 8, DCOx = 3,
MODx = 0
2.2 V/3 V
1.10
2.10
MHz
fDCO(9,3)
DCO frequency (9, 3)
RSELx = 9, DCOx = 3,
MODx = 0
2.2 V/3 V
1.60
3.00
MHz
fDCO(10,3)
DCO frequency (10, 3)
RSELx = 10, DCOx = 3,
MODx = 0
2.2 V/3 V
2.50
4.30
MHz
fDCO(11,3)
DCO frequency (11, 3)
RSELx = 11, DCOx = 3,
MODx = 0
2.2 V/3 V
3.00
5.50
MHz
fDCO(12,3)
DCO frequency (12, 3)
RSELx = 12, DCOx = 3,
MODx = 0
2.2 V/3 V
4.30
7.30
M Hz
fDCO(13,3)
DCO frequency (13, 3)
RSELx = 13, DCOx = 3,
MODx = 0
2.2 V/3 V
6.00
9.60
MHz
fDCO(14,3)
DCO frequency (14, 3)
RSELx = 14, DCOx = 3,
MODx = 0
2.2 V/3 V
8.60
13.9
MHz
fDCO(15,3)
DCO frequency (15, 3)
RSELx = 15, DCOx = 3,
MODx = 0
3V
12.0
18.5
MHz
fDCO(15,7)
DCO frequency (15, 7)
RSELx = 15, DCOx = 7,
MODx = 0
3V
16.0
26.0
MHz
SRSEL
Frequency step between
range RSEL and RSEL+1
SRSEL =
fDCO(RSEL+1,DCO)/fDCO(RSEL,DCO)
1.55
ratio
Copyright © 2010–2011, Texas Instruments Incorporated
2.2 V/3 V
0.06
0.14
MHz
2.2 V/3 V
39
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
DCO Frequency – Electrical Characteristics (continued)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
SDCO
Frequency step between
tap DCO and DCO+1
Duty cycle
TEST CONDITIONS
VCC
MIN
TYP
MAX
UNIT
SDCO =
fDCO(RSEL,DCO+1)/fDCO(RSEL,DCO)
2.2 V/3 V
1.05
1.08
1.12
ratio
Measured at P1.4/SMCLK
2.2 V/3 V
40
50
60
%
Calibrated DCO Frequencies (Tolerance at Calibration) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
Frequency tolerance at calibration
TA
VCC
MIN
TYP
MAX
25°C
3V
–1
±0.2
1
UNIT
25°C
3V
0.990
1
1.010
MHz
%
fCAL(1 MHz)
1-MHz calibration value
BCSCTL1 = CALBC1_1MHZ,
DCOCTL = CALDCO_1MHZ,
Gating time: 5 ms
fCAL(8 MHz)
8-MHz calibration value
BCSCTL1 = CALBC1_8MHZ,
DCOCTL = CALDCO_8MHZ,
Gating time: 5 ms
25°C
3V
7.920
8
8.080
MHz
fCAL(12 MHz)
12-MHz calibration value
BCSCTL1 = CALBC1_12MHZ,
DCOCTL = CALDCO_12MHZ,
Gating time: 5 ms
25°C
3V
11.88
12
12.12
MHz
fCAL(16 MHz)
16-MHz calibration value
BCSCTL1 = CALBC1_16MHZ,
DCOCTL = CALDCO_16MHZ,
Gating time: 2 ms
25°C
3V
15.84
16
16.16
MHz
Calibrated DCO Frequencies (Tolerance Over Temperature) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
TA
VCC
MIN
TYP
MAX
1-MHz tolerance over temperature
PARAMETER
0°C to 85°C
3V
–2.5
±0.5
2.5
%
8-MHz tolerance over temperature
0°C to 85°C
3V
–2.5
±1.0
2.5
%
12-MHz tolerance over temperature
0°C to 85°C
3V
–2.5
±1.0
2.5
%
16-MHz tolerance over temperature
0°C to 85°C
3V
–3.0
±2.0
3.0
%
2.2 V
0.970
1
1.030
fCAL(1MHz)
fCAL(8MHz)
fCAL(12MHz)
fCAL(16MHz)
40
1-MHz calibration value
8-MHz calibration value
TEST CONDITIONS
BCSCTL1 = CALBC1_1MHz,
DCOCTL = CALDCO_1MHZ,
Gating time: 5 ms
0°C to 85°C
BCSCTL1 = CALBC1_8MHZ,
DCOCTL = CALDCO_8MHZ,
Gating time: 5 ms
0°C to 85°C
12-MHz calibration value
BCSCTL1 = CALBC1_12MHZ,
DCOCTL = CALDCO_12MHZ,
Gating time: 5 ms
16-MHz calibration value
BCSCTL1 = CALBC1_16MHZ,
DCOCTL = CALDCO_16MHZ,
Gating time: 2 ms
0°C to 85°C
0°C to 85°C
3V
0.975
1
1.025
3.6 V
0.970
1
1.030
2.2 V
7.760
8
8.400
3V
7.800
8
8.200
3.6 V
7.600
8
8.240
2.2 V
11.70
12
12.30
3V
11.70
12
12.30
3.6 V
11.70
12
12.30
3V
15.52
16
16.48
3.6 V
15.00
16
16.48
UNIT
MHz
MHz
MHz
MHz
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Calibrated DCO Frequencies (Tolerance Over Supply Voltage VCC) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
VCC
MIN
TYP
MAX
1-MHz tolerance over VCC
25°C
8-MHz tolerance overVCC
25°C
12-MHz tolerance over VCC
16-MHz tolerance over VCC
UNIT
1.8 V to 3.6 V
–3
±2
3
%
1.8 V to 3.6 V
–3
±2
3
%
25°C
2.2 V to 3.6 V
–3
±2
3
%
25°C
3 V to 3.6 V
–6
±2
3
%
fCAL(1MHz)
1-MHz
calibration value
BCSCTL1 = CALBC1_1MHZ,
DCOCTL = CALDCO_1MHZ,
Gating time: 5 ms
25°C
1.8 V to 3.6 V
0.970
1
1.030
MHz
fCAL(8MHz)
8-MHz
calibration value
BCSCTL1 = CALBC1_8MHZ,
DCOCTL = CALDCO_8MHZ,
Gating time: 5 ms
25°C
1.8 V to 3.6 V
7.760
8
8.240
MHz
fCAL(12MHz)
12-MHz
calibration value
BCSCTL1 = CALBC1_12MHZ,
DCOCTL = CALDCO_12MHZ,
Gating time: 5 ms
25°C
2.2 V to 3.6 V
11.64
12
12.36
MHz
fCAL(16MHz)
16-MHz
calibration value
BCSCTL1 = CALBC1_16MHZ,
DCOCTL = CALDCO_16MHZ,
Gating time: 2 ms
25°C
3 V to 3.6 V
15.00
16
16.48
MHz
Calibrated DCO Frequencies (Overall Tolerance) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
VCC
MIN
TYP
MAX
1-MHz tolerance
over temperature
–55°C to 150°C
8-MHz tolerance
over temperature
UNIT
1.8 V to 3.6 V
-5
±2
+5
%
–55°C to 150°C
1.8 V to 3.6 V
-5
±2
+5
%
12-MHz tolerance
over temperature
–55°C to 150°C
2.2 V to 3.6 V
-5
±2
+5
%
16-MHz tolerance
over temperature
–55°C to 150°C
3 V to 3.6 V
-6
±3
+6
%
fCAL(1MHz)
1-MHz
calibration value
BCSCTL1 = CALBC1_1MHZ,
DCOCTL = CALDCO_1MHZ,
Gating time: 5 ms
–55°C to 150°C
1.8 V to 3.6 V
.950
1
1.050
MHz
fCAL(8MHz)
8-MHz
calibration value
BCSCTL1 = CALBC1_8MHZ,
DCOCTL = CALDCO_8MHZ,
Gating time: 5 ms
–55°C to 150°C
1.8 V to 3.6 V
7.6
8
8.4
MHz
fCAL(12MHz)
12-MHz
calibration value
BCSCTL1 = CALBC1_12MHZ,
DCOCTL = CALDCO_12MHZ,
Gating time: 5 ms
–55°C to 150°C
2.2 V to 3.6 V
11.4
12
12.6
MHz
fCAL(16MHz)
16-MHz
calibration value
BCSCTL1 = CALBC1_16MHZ,
DCOCTL = CALDCO_16MHZ,
Gating time: 2 ms
–55°C to 150°C
3 V to 3.6 V
15.00
16
17.00
MHz
Copyright © 2010–2011, Texas Instruments Incorporated
41
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Typical Characteristics – Calibrated 1-MHz DCO Frequency
1.02
Frequency - MHz
1.01
TA = 105°C
TA = 85°C
1
TA = 25°C
0.99
TA = –40°C
0.98
1.5
2
2.5
3
3.5
4
VCC - Supply Voltage - V
Figure 15. Calibrated 1-MHz Frequency vs VCC
Typical Characteristics – Calibrated 8-MHz DCO Frequency
8.20
TA = 105°C
8.15
Frequency - MHz
8.10
8.05
8
TA = 85°C
TA = 25°C
7.95
TA = –40°C
7.90
7.85
7.80
1.5
2
2.5
3
3.5
4
VCC - Supply Voltage - V
Figure 16. Calibrated 8-MHz Frequency vs VCC
42
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Typical Characteristics – Calibrated 12-MHz DCO Frequency
12.2
Frequency - MHz
12.1
TA = –40°C
TA = 25°C
12
TA = 85°C
11.9
TA = 105°C
11.8
11.7
1.5
2
2.5
3
3.5
4
VCC - Supply Voltage - V
Figure 17. Calibrated 12-MHz Frequency vs VCC
Typical Characteristics – Calibrated 16-MHz DCO Frequency
16.1
16
Frequency - MHz
TA = –40°C
15.9
TA = 25°C
TA = 85°C
15.8
TA = 105°C
15.7
15.6
1.5
2
2.5
3
3.5
4
VCC - Supply Voltage - V
Figure 18. Calibrated 16-MHz Frequency vs VCC
Copyright © 2010–2011, Texas Instruments Incorporated
43
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Wake-Up From Low-Power Modes (LPM3/4) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
tDCO,LPM3/4
tCPU,LPM3/4
(1)
(2)
TEST CONDITIONS
DCO clock wake-up time
from LPM3/4 (1)
VCC
MIN
TYP
MAX
BCSCTL1 = CALBC1_1MHZ,
DCOCTL = CALDCO_1MHZ,
2.2 V/3 V
2
BCSCTL1 = CALBC1_8MHZ,
DCOCTL = CALDCO_8MHZ,
2.2 V/3 V
1.5
BCSCTL1 = CALBC1_12MHZ,
DCOCTL = CALDCO_12MHZ,
3V
1
BCSCTL1 = CALBC1_16MHZ,
DCOCTL = CALDCO_16MHZ,
3V
1
UNIT
μs
1/fMCLK +
tClock,LPM3/4
CPU wake-up time from LPM3/4 (2)
The DCO clock wake-up time is measured from the edge of an external wake-up signal (e.g., port interrupt) to the first clock edge
observable externally on a clock pin (MCLK or SMCLK).
Parameter applicable only if DCOCLK is used for MCLK.
Typical Characteristics – DCO Clock Wake-Up Time From LPM3/4
DCO Wake Time − us
10.00
RSELx = 0...11
RSELx = 12...15
1.00
0.10
0.10
1.00
10.00
DCO Frequency − MHz
Figure 19. Clock Wake-Up Time From LPM3 vs DCO Frequency
DCO With External Resistor ROSC – Electrical Characteristics (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
TYP
1.8
UNIT
fDCO,ROSC
DCO output frequency with ROSC
DCOR = 1, RSELx = 4, DCOx = 3, MODx = 0,
TA = 25°C
2.2 V
3V
1.95
Dt
Temperature drift
DCOR = 1, RSELx = 4, DCOx = 3, MODx = 0
2.2 V/3 V
±0.1
%/°C
DV
Drift with VCC
DCOR = 1, RSELx = 4, DCOx = 3, MODx = 0
2.2 V/3 V
10
%/V
(1)
44
MHz
ROSC = 100 kΩ. Metal film resistor, type 0257. 0.6 watt with 1% tolerance and TK = ±50 ppm/°C
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Typical Characteristics - DCO With External Resistor ROSC
10.00
DCO Frequency − MHz
DCO Frequency − MHz
10.00
1.00
0.10
RSELx = 4
0.01
10.00
100.00
1000.00
10000.00
ROSC − External Resistor − kW
1.00
0.10
RSELx = 4
0.01
10.00
100.00
1000.00
10000.00
ROSC − External Resistor − kW
Figure 20. DCO Frequency vs ROSC,
VCC = 2.2 V, TA = 25°C
Figure 21. DCO Frequency vs ROSC,
VCC = 3.0 V, TA = 25°C
2.000
1.800
ROSC = 100k
DCO Frequency - MHz
1.600
1.400
1.200
1.000
ROSC = 270k
0.800
0.600
0.400
ROSC = 1M
0.200
0.000
-75
-25
25
75
125
175
TA - Temperature - °C
Figure 22. DCO Frequency vs Temperature,
VCC = 3.0 V
Copyright © 2010–2011, Texas Instruments Incorporated
Figure 23. DCO Frequency vs VCC,
TA = 25°C
45
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Crystal Oscillator (LFXT1) Low-Frequency Modes – Electrical Characteristics (1)
(2) (2)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
fLFXT1,LF
LFXT1 oscillator crystal
frequency, LF mode 0, 1
LFXT1 oscillator
fLFXT1,LF,logic logic-level square-wave
input frequency, LF mode
OALF
CL,eff
Oscillation allowance for
LF crystals
Integrated effective load
capacitance,
LF mode (3)
TEST CONDITIONS
VCC
MIN
XTS = 0, LFXT1Sx = 0 or 1
1.8 V to 3.6 V
XTS = 0, LFXT1Sx = 3
1.8 V to 3.6 V
10,000
500
XTS = 0, LFXT1Sx = 0;
fLFXT1,LF = 32,768 kHz,
CL,eff = 12 pF
200
XCAPx = 0
1
XCAPx = 1
5.5
XCAPx = 2
8.5
XCAPx = 3
11
XTS = 0, Measured at
P1.4/ACLK,
fLFXT1,LF = 32,768 Hz
2.2 V/3 V
30
fFault,LF
Oscillator fault frequency
threshold, LF mode (4)
XTS = 0, LFXT1Sx = 3 (5)
2.2 V/3 V
10
(3)
(4)
(5)
UNIT
Hz
50,000
Hz
kΩ
LF mode
(2)
32,768
XTS = 0, LFXT1Sx = 0;
fLFXT1,LF = 32,768 kHz,
CL,eff = 6 pF
XTS = 0
MAX
32,768
Duty Cycle
(1)
TYP
pF
50
70
%
10,000
Hz
To improve EMI on the LFXT1 oscillator the following guidelines should be observed:
(a) Keep as short of a trace as possible between the device and the crystal.
(b) Design a good ground plane around the oscillator pins.
(c) Prevent crosstalk from other clock or data lines into oscillator pins XIN and XOUT.
(d) Avoid running PCB traces underneath or adjacent to the XIN and XOUT pins.
(e) Use assembly materials and praxis to avoid any parasitic load on the oscillator XIN and XOUT pins.
(f) If conformal coating is used, ensure that it does not induce capacitive/resistive leakage between the oscillator pins.
(g) Do not route the XOUT line to the JTAG header to support the serial programming adapter as shown in other documentation. This
signal is no longer required for the serial programming adapter.
LFXT1 in 32-KHz mode is guaranteed to function only between –55°C to 105°C. This module is know to fail above 110°C. For further
info contact TI support.
Includes parasitic bond and package capacitance (approximately 2 pF per pin). Since the PCB adds additional capacitance it is
recommended to verify the correct load by measuring the ACLK frequency. For a correct setup the effective load capacitance should
always match the specification of the used crystal.
Frequencies below the MIN specification set the fault flag, frequencies above the MAX specification do not set the fault flag.
Frequencies in between might set the flag.
Measured with logic-level input frequency, but also applies to operation with crystals.
Internal Very-Low-Power, Low-Frequency Oscillator (VLO) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
fVLO
VLO frequency
dfVLO/dT
VLO frequency temperature drift
dfVLO/dVCC VLO frequency supply voltage drift
(1)
(2)
46
TEST
CONDITIONS
TA
VCC
–55°C to 85°C
2.2 V/3 V
150°C
2.2 V/3 V
See
(1)
2.2 V/3 V
See
(2)
1.8 V –
3.6V
25°C
MIN
4
TYP MAX
12
20
22
0.5
4
0.8
UNIT
kHz
%/°C
%/V
Calculated using the box method:
S Version: (MAX(–55 to 150°C) – MIN(–55 to 150°C))/MIN(–55 to 150°C)/(150°C – (–55°C))
Calculated using the box method: (MAX(1.8 V to 3.6 V) – MIN(1.8V to 3.6 V))/MIN(1.8 V to 3.6 V)/(3.6 V – 1.8 V)
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Crystal Oscillator (LFXT1) High Frequency Modes – Electrical Characteristics (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
MIN
TYP
MAX
UNIT
fLFXT1,HF0
LFXT1 oscillator crystal frequency,
HF mode 0
XTS = 1, LFXT1Sx = 0
1.8 V to 3.6 V
0.4
1
MHz
fLFXT1,HF1
LFXT1 oscillator lcrystal frequency,
HF mode 1
XTS = 1, LFXT1Sx = 1
1.8 V to 3.6 V
1
4
MHz
1.8 V to 3.6 V
2
10
fLFXT1,HF2
LFXT1 oscillator crystal frequency,
HF mode 2
XTS = 1, LFXT1Sx = 2
2.2 V to 3.6 V
2
12
3 V to 3.6 V
2
16
1.8 V to 3.6 V
0.4
10
2.2 V to 3.6 V
0.4
12
3 V to 3.6 V
0.4
16
fLFXT1,HF,logic
OAHF
CL,eff
Duty Cycle
fFault,HF
(1)
(2)
(3)
(4)
(5)
LFXT1 oscillator logic-level
square-wave input frequency,
HF mode
Oscillation allowance for HF crystals
(see Figure 24 and Figure 25)
Integrated effective load capacitance,
HF mode (2)
HF mode
Oscillator fault frequency, HF mode (4)
XTS = 1, LFXT1Sx = 3
XTS = 0, LFXT1Sx = 0;
fLFXT1,HF = 1 MHz,
CL,eff = 15 pF
2700
XTS = 0, LFXT1Sx = 1
fLFXT1,HF = 4 MHz,
CL,eff = 15 pF
800
XTS = 0, LFXT1Sx = 2
fLFXT1,HF = 16 MHz,
CL,eff = 15 pF
300
XTS = 1 (3)
XTS = 1, Measured at
P1.4/ACLK,
fLFXT1,HF = 10 MHz
XTS = 1, Measured at
P1.4/ACLK,
fLFXT1,HF = 16 MHz
XTS = 1, LFXT1Sx = 3 (5)
MHz
Ω
1
pF
40
50
60
40
50
60
3V
2.2 V/3 V
MHz
%
30
300
kHz
To improve EMI on the LFXT1 oscillator the following guidelines should be observed:
(a) Keep as short of a trace as possible between the device and the crystal.
(b) Design a good ground plane around the oscillator pins.
(c) Prevent crosstalk from other clock or data lines into oscillator pins XIN and XOUT.
(d) Avoid running PCB traces underneath or adjacent to the XIN and XOUT pins.
(e) Use assembly materials and praxis to avoid any parasitic load on the oscillator XIN and XOUT pins.
(f) If conformal coating is used, ensure that it does not induce capacitive/resistive leakage between the oscillator pins.
(g) Do not route the XOUT line to the JTAG header to support the serial programming adapter as shown in other documentation. This
signal is no longer required for the serial programming adapter.
Includes parasitic bond and package capacitance (approximately 2 pF per pin). Since the PCB adds additional capacitance it is
recommended to verify the correct load by measuring the ACLK frequency. For a correct setup the effective load capacitance should
always match the specification of the used crystal.
Requires external capacitors at both terminals. Values are specified by crystal manufacturers.
Frequencies below the MIN specification set the fault flag, frequencies above the MAX specification do not set the fault flag.
Frequencies in between might set the flag.
Measured with logic-level input frequency, but also applies to operation with crystals
Copyright © 2010–2011, Texas Instruments Incorporated
47
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Typical Characteristics – LFXT1 Oscillator in HF Mode (XTS = 1)
Figure 24. Oscillation Allowance vs Crystal Frequency, CL,eff = 15 pF, TA = 25°C
1500
XT Oscillator Supply Current - mA
1400
1300
LFXT1Sx = 2
1200
1100
1000
900
800
700
600
500
400
300
LFXT1Sx = 1
200
100
LFXT1Sx = 0
0
0
4
8
12
16
20
Crystal Frequency - MHz
Figure 25. XT Oscillator Supply Current vs Crystal Frequency, CL,eff = 15 pF, TA = 25°C
48
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Crystal Oscillator (XT2) – Electrical Characteristics (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
MIN
TYP
MAX
UNIT
fXT2
XT2 oscillator crystal frequency,
mode 0
XT2Sx = 0
1.8 V to 3.6 V
0.4
0.9
MHz
fXT2
XT2 oscillator lcrystal frequency,
mode 1
XT2Sx = 1
1.8 V to 3.6 V
1
4
MHz
1.8 V to 3.6 V
2
10
fXT2
XT2 oscillator crystal frequency,
mode 2
XT2Sx = 2
2.2 V to 3.6 V
2
12
3 V to 3.6 V
2
16
1.8 V to 3.6 V
0.4
10
2.2 V to 3.6 V
0.4
12
3 V to 3.6 V
0.4
16
XT2 oscillator logic-level
square-wave input frequency,
fXT2
Oscillation allowance
(see Figure 26 and Figure 27)
OA
CL,eff
Integrated effective load capacitance,
HF mode (2)
Duty Cycle HF mode
fFault
(1)
(2)
(3)
(4)
(5)
Oscillator fault frequency, HF mode (4)
XT2Sx = 3
XT2Sx = 0, fXT2 = 1 MHz;
CL,eff = 15 pF
2700
XT2Sx = 1, fXT2 = 4MHz;
CL,eff = 15 pF
800
XT2Sx = 2, fXT1, HF = 16
MHz;
CL,eff = 15 pF
300
See
(3)
Measured at P1.4/SMCLK,
fXT2 = 10 MHz
Measured at P1.4/SMCLK,
fXT2 = 16 MHz
XT2Sx = 3 (5)
MHz
Ω
1
pF
40
50
60
40
50
60
2.2 V/3 V
2.2 V/3 V
MHz
%
30
300
kHz
To improve EMI on the LFXT1 oscillator the following guidelines should be observed:
(a) Keep as short of a trace as possible between the device and the crystal.
(b) Design a good ground plane around the oscillator pins.
(c) Prevent crosstalk from other clock or data lines into oscillator pins XIN and XOUT.
(d) Avoid running PCB traces underneath or adjacent to the XIN and XOUT pins.
(e) Use assembly materials and praxis to avoid any parasitic load on the oscillator XIN and XOUT pins.
(f) If conformal coating is used, ensure that it does not induce capacitive/resistive leakage between the oscillator pins.
(g) Do not route the XOUT line to the JTAG header to support the serial programming adapter as shown in other documentation. This
signal is no longer required for the serial programming adapter.
Includes parasitic bond and package capacitance (approximately 2 pF per pin). Since the PCB adds additional capacitance it is
recommended to verify the correct load by measuring the ACLK frequency. For a correct setup the effective load capacitance should
always match the specification of the used crystal.
Requires external capacitors at both terminals. Values are specified by crystal manufacturers.
Frequencies below the MIN specification set the fault flag, frequencies above the MAX specification do not set the fault flag.
Frequencies in between might set the flag.
Measured with logic-level input frequency, but also applies to operation with crystals.
Copyright © 2010–2011, Texas Instruments Incorporated
49
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Typical Characteristics – XT2 Oscillator
Figure 26. Oscillation Allowance vs Crystal Frequency, CL,eff = 15 pF, TA = 25°C
1500
XT Oscillator Supply Current - mA
1400
1300
XT2Sx = 2
1200
1100
1000
900
800
700
600
500
400
300
XT2Sx = 1
200
100
0
XT2Sx = 0
0
4
8
12
16
20
Crystal Frequency - MHz
Figure 27. XT2 Oscillator Supply Current vs Crystal Frequency, CL,eff = 15 pF, TA = 25°C
50
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Timer_A – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
fTA
Timer_A clock frequency
Internal: SMCLK, ACLK,
External: TACLK, INCLK,
Duty cycle = 50% ±10%
tTA,cap
Timer_A, capture timing
TA0, TA1, TA2
VCC
MIN
MAX
2.2 V
10
3V
16
2.2 V/3 V
20
UNIT
MHz
ns
Timer_B – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
fTB
Timer_B clock frequency
Internal: SMCLK, ACLK,
External: TBCLK,
Duty Cycle = 50% ±10%
tTB,cap
Timer_B, capture timing
TB0, TB1, TB2
VCC
MIN
MAX
2.2 V
10
3V
16
2.2 V/3 V
20
UNIT
MHz
ns
USCI (UART Mode) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
fUSCI
USCI input clock frequency
fBITCLK
BITCLK clock frequency
(equals baud rate in MBaud)
tτ
UART receive deglitch time (1)
(1)
TEST CONDITIONS
VCC
MIN
TYP
Internal: SMCLK, ACLK,
External: UCLK;
Duty cycle = 50% ±10%
2.2 V/3 V
MAX
UNIT
fSYSTEM
MHz
1
MHz
2.2 V
50
150
600
3V
50
150
600
ns
Pulses on the UART receive input (UCxRX) shorter than the UART receive deglitch time are suppressed. To ensure that pulses are
correctly recognized, their width should exceed the maximum specification of the deglitch time.
USCI (SPI Master Mode) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (1) (see Figure 28
and Figure 29)
PARAMETER
fUSCI
USCI input clock frequency
tSU,MI
SOMI input data setup time
tHD,MI
SOMI input data hold time
tVALID,MO
SIMO output data valid time
(1)
TEST CONDITIONS
VCC
MIN
SMCLK, ACLK,
Duty cycle = 50% ±10%
UCLK edge to SIMO valid,
CL = 20 pF
2.2 V
110
3V
75
2.2 V
0
3V
0
MAX
UNIT
fSYSTEM
MHz
ns
ns
2.2 V
30
3V
20
ns
fUCxCLK = 1/2tLO/HI with tLO/HI ≥ max(tVALID,MO(USCI) + tSU,SI(Slave), tSU,MI(USCI) + tVALID,SO(Slave)).
For the slave parameters tSU,SI(Slave) and tVALID,SO(Slave), see the SPI parameters of the attached slave.
Copyright © 2010–2011, Texas Instruments Incorporated
51
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
USCI (SPI Slave Mode) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (1) (see Figure 30
and Figure 31)
PARAMETER
TEST CONDITIONS
VCC
MIN
TYP
MAX
UNIT
tSTE,LEAD
STE lead time,
STE low to clock
2.2 V/3 V
tSTE,LAG
STE lag time,
Last clock to STE high
2.2 V/3 V
tSTE,ACC
STE access time,
STE low to SOMI data out
2.2 V/3 V
50
ns
tSTE,DIS
STE disable time,
STE high to SOMI high
impedance
2.2 V/3 V
50
ns
tSU,SI
SIMO input data setup time
tHD,SI
SIMO input data hold time
tVALID,SO
SOMI output data valid time
(1)
UCLK edge to SOMI valid,
CL = 20 pF
50
ns
10
2.2 V
20
3V
15
2.2 V
10
3V
10
ns
ns
ns
2.2 V
75
110
3V
50
75
ns
fUCxCLK = 1/2tLO/HI with tLO/HI ≥ max(tVALID,MO(USCI) + tSU,SI(Slave), tSU,MI(USCI) + tVALID,SO(Slave)).
For the slave parameters tSU,SI(Slave) and tVALID,SO(Slave), see the SPI parameters of the attached slave.
1/fUCxCLK
CKPL
=0
CKPL
=1
UCLK
tLOW/HIGH tLOW/HIGH
tSU,MI
tHD,MI
SCMI
tVALID, MO
SIMO
Figure 28. SPI Master Mode, CKPH = 0
52
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
1/fUCxCLK
CKPL
=0
CKPL
=1
UCLK
tLOW/HIGH tLOW/HIGH
tHD,MI
tSU,MI
SCMI
tVALID, MO
SIMO
Figure 29. SPI Master Mode, CKPH = 1
tSTE,LEAD
tSTE,LAG
STE
1/fUCxCLK
CKPL = 0
UCLK
CKPL = 1
tLOW,HIGH tLOW,HIGH
tSU,SIMO
tHD,SIMO
SIMO
tACC
tVALID,SOMI
tDIS
SOMI
Figure 30. SPI Slave Mode, CKPH = 0
Copyright © 2010–2011, Texas Instruments Incorporated
53
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
tSTE,LEAD
tSTE,LAG
STE
1/fUCxCLK
CKPL = 0
UCLK
CKPL = 1
tLOW,HIGH tLOW,HIGH
tHD,SI
,
tSU,SI
SIMO
tACC
tVALID,SO
tDIS
SOMI
Figure 31. SPI Slave Mode, CKPH = 1
54
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
USCI (I2C Mode) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 32)
PARAMETER
TEST CONDITIONS
VCC
MIN
Internal: SMCLK, ACLK,
External: UCLK,
Duty cycle = 50% ± 10%
TYP
MAX
fSYSTEM
UNIT
fUSCI
USCI input clock frequency
fSCL
SCL clock frequency
tHD,STA
Hold time (repeated) START
tSU,STA
Set-up time for a repeated START
tHD,DAT
Data hold time
2.2 V/3 V
0
tSU,DAT
Data set-up time
2.2 V/3 V
250
ns
tSU,STO
Set-up time for STOP
2.2 V/3 V
4.0
μs
tSP
Pulse width of spikes suppressed by
input filter
2.2 V
50
150
600
3V
50
100
600
2.2 V/3 V
fSCL ≤ 100 kHz
fSCL ≤ 100 kHz
4.7
μs
0.6
tSU ,STA tHD ,STA
kHz
μs
0.6
2.2 V/3 V
fSCL > 100 kHz
400
4.0
2.2 V/3 V
fSCL > 100 kHz
tHD ,STA
0
MHz
ns
ns
tBUF
SDA
t
LOW
tHIGH
tSP
SCL
tSU ,DAT
tSU , STO
tHD ,DAT
Figure 32. I2C Mode Timing
Copyright © 2010–2011, Texas Instruments Incorporated
55
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Comparator_A+ – Electrical Characteristics (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
MIN
TYP
MAX
2.2 V
25
80
3V
45
96
I(DD)
CAON = 1 CARSEL = 0 CAREF = 0
CAON = 1, CARSEL = 0,
CAREF = 1/2/3 no load at P2
3/CA0/TA1
and P2.4/CA1/TA2
2.2 V/3 V
30
50
I(Refladder/Refdiode)
3V
45
71
V(IC)
Common-mode input voltage
CAON =1
2.2 V/3 V
0
V(Ref025)
Voltage at 0.25 VCC node/VCC
PCA0 = 1, CARSEL = 1, CAREF =
1,
no load at P2.3/CA0/TA1
and P2.4/CA1/TA2
2.2 V/3 V
0.23
V(Ref050)
Voltage at 0.5 VCC node/VCC
PCA0 = 1, CARSEL = 1, CAREF =
2,
no load at P2.3/CA0/TA1
and P2.4/CA1/TA2
2.2 V/3 V
V(RefVT)
See Figure 36 and Figure 37
PCA0 = 1, CARSEL = 1, CAREF =
3,
no load at P2.3/CA0/TA1
and P2.4/CA1/TA2, TA = 85°C
V(offset)
Offset voltage
See
Vhys
Input hysteresis
CAON=1
t(response)
(1)
(2)
(3)
56
Response time, low-to-high and
high-to-low (3)
UNIT
μA
μA
VCC - 1
V
0.24
0.25
V
0.47
0.48
0.5
V
2.2 V
390
480
540
3V
400
490
550
2.2 V/3 V
–30
30
mV
2.2 V/3 V
0
0.7
1.4
mV
TA = 25°C, Overdrive 10 mV,
Without filter: CAF = 0
2.2 V
80
165
300
3V
70
120
240
TA = 25°C, Overdrive 10 mV,
Without filter: CAF = 1
2.2 V
1.4
1.9
2.8
3V
0.9
1.5
2.2
(2)
mV
ns
µs
The leakage current for the Comparator_A+ terminals is identical to Ilkg(Px.x) specification.
The input offset voltage can be cancelled by using the CAEX bit to invert the Comparator_A+ inputs on successive measurements.
The two successive measurements are then summed together.
The response time is measured at P2.2/CAOUT/TA0/CA4 with an input voltage step, with Comparator_A+ already enabled (CAON = 1).
If CAON is set at the same time, a settling time of up to 300 ns is added to the response time.
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
0V
VCC
0
1
CAF
CAON
Low Pass Filter
V+
+
V-
-
0
0
1
1
To Internal
Modules
CAOUT
Set CAIFG
Flag
l » 2 ms
Figure 33. Block Diagram of Comparator_A Module
VCAOUT
Overdrive
V-
400 mV
t(response)
V+
Figure 34. Overdrive Definition
CASHORT
CA0
CA1
1
+
VIN
-
IOUT = 10 mA
Comparator_A+
CASHORT = 1
Figure 35. Comparator_A+ Short Resistance Test Condition
Copyright © 2010–2011, Texas Instruments Incorporated
57
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Typical Characteristics – Comparator A+
Figure 36. V(RefVT) vs Temperature, VCC = 3 V
Figure 37. V(RefVT) vs Temperature, VCC = 2.2 V
Figure 38. Short Resistance vs VIN/VCC
58
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
12-Bit ADC Power-Supply and Input Range Conditions – Electrical Characteristics (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
AVCC
Analog supply voltage range
V(P6.x/Ax)
Analog input voltage range
IADC12
Operating supply current
into AVCC terminal (3)
IREF+
TEST CONDITIONS
(2)
Reference supply current,
into AVCC terminal (4)
AVCC and DVCC are connected
together,
AVSS and DVSS are connected
together,
V(AVSS) = V(DVSS) = 0 V
All P6.0/A0 to P6.7/A7 terminals.
Analog inputs selected in
ADC12MCTLx register
and P6Sel.x = 1, 0 ≤ x ≤ 7,
V(AVSS) ≤ VP6.x/Ax ≤ V(AVCC)
fADC10CLK = 5 MHz,
ADC12ON = 1, REFON = 0,
SHT0 = 0, SHT1 = 0,
ADC12DIV = 0
fADC12CLK = 5 MHz,
ADC12ON = 0,
REFON = 1, REF2_5V = 1
fADC12CLK = 5 MHz,
ADC12ON = 0,
REFON = 1, REF2_5V = 0
CI (5)
Input capacitance
Only one terminal selected at a time,
P6.x/Ax
RI (5)
Input MUX ON resistance
0 V ≤ VAx ≤ VAVCC
(1)
(2)
(3)
(4)
(5)
VCC
MIN
TYP
MAX
2.2
3.6
V
0
VAVCC
V
2.2 V
0.65
0.8
3V
0.8
1
3V
0.5
0.7
2.2 V
0.5
0.7
3V
0.5
0.7
2.2 V
3V
UNIT
mA
mA
40
pF
2000
Ω
The leakage current is defined in the leakage current table with P6.x/Ax parameter.
The analog input voltage range must be within the selected reference voltage range VR+ to VR– for valid conversion results.
The internal reference supply current is not included in current consumption parameter IADC12.
The internal reference current is supplied via terminal VCC. Consumption is independent of the ADC10ON control bit, unless a
conversion is active. The REFON bit enables the built-in reference to settle before starting an A/D conversion.
Limits verified by design.
Copyright © 2010–2011, Texas Instruments Incorporated
59
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
12-Bit ADC External Reference – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
MIN
TYP
MAX
UNIT
VeREF+
Positive external
reference voltage input
VeREF+ > VREF-/VeREF-
(1)
1.4
VAVCC
V
VREF- /VeREF+
Negative external
reference voltage input
VeREF+ > VREF-/VeREF-
(2)
0
1.2
V
(VeREF+ - VREF- / VeREF- )
Differential external
reference voltage input
VeREF+ > VREF-/VeREF-
(3)
1.4
VAVCC
V
IVeREF+
Static input current
0 V ≤ VeREF+ ≤ VAVCC
2.2 V/3 V
±1
µA
IVREF-/VeREF-
Static input current
0 V ≤ VeREF- ≤ VAVCC
2.2 V/3 V
±1
µA
(1)
(2)
(3)
60
The accuracy limits the minimum positive external reference voltage. Lower reference voltage levels may be applied with reduced
accuracy requirements.
The accuracy limits the maximum negative external reference voltage. Higher reference voltage levels may be appliedwith reduced
accuracy requirements.
The accuracy limitsminimum external differential reference voltage. Lower differential reference voltage levels may be appliedwith
reduced accuracy requirements.
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
12-Bit ADC Built-In Reference – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
Positive built-in
reference voltage
output
VREF+
AVCC(min)
AVCC minimum
voltage, positive
built-in reference
active
TA
REF2_5V = 1 (2.5 V)
IVREF+max ≤ IVREF+ ≤ IVREF+min
-55°C to 85°C
REF2_5V = 1 (1.5 V)
IVREF+max ≤ IVREF+ ≤ IVREF+min
-55°C to 85°C
IL(VREF)+ (1)
Load current
regulation, VREF+
terminal
150°C
3V
2.2 V/3 V
2.64
1.44
1.5
1.56
1.42
1.5
1.57
2.9
UNIT
V
V
2.2 V
0.01
–0.5
3V
0.01
–1
2.2 V
±2
3V
±2
mA
LSB
IVREF+ = 500 μA ± 100 μA,
Analog input voltage VAx ≉ 1.25 V,
REF2_5V = 1
3V
±2
3V
20
CVREF+
Capacitance
at pin VREF+ (3)
REFON = 1,
0 mA ≤ IVREF+ ≤ IVREF+max
2.2 V/3 V
TREF+ (1)
Temperature
coefficient of built-in
reference
IVREF+ is a constant in the range of
0 mA ≤ IVREF+ ≤ 1 mA
2.2 V/3 V
Settling time of
internal reference
voltage (4)
(See Figure 39)
IVREF+ = 0.5 mA, CVREF+ = 10 μF,
VREF+ = 1.5 V, VAVCC = 2.2 V
(4)
2.6
2.5
REF2_5V = 1,
–1 mA ≤ IVREF+ ≤ IVREF+min
IVREF+ = 100 μA → 900 μA,
CVREF+ = 5 μF, at ≉ 0.5 VREF+,
Error of conversion result ≤ 1 LSB
(1)
(2)
(3)
2.5
2.8
Load current
regulation, VREF+
terminal
(1)
2.4
REF2_5V = 1,
–0.5 mA ≤ IVREF+ ≤ IVREF+min
IVREF+ = 500 μA ± 100 μA,
Analog input voltage VAx ≉ 0.75 V,
REF2_5V = 0
TYP MAX
2.37
2.2
IDL(VREF)+ (2)
tREFON
MIN
REF2_5V = 0,
IVREF+max ≤ IVREF+ ≤ IVREF+min
Load current out of
VREF+ terminal
IVREF+
150°C
VCC
5
ns
µF
10
±100
17
ppm/°
C
ms
Limits characterized
Limits verified by design
The internal buffer operational amplifier and the accuracy specifications require an external capacitor. All INL and DNL tests use two
capacitors between pins VREF+ and AVSS and VREF-/VeREF- and AVSS: 10 μF tantalum and 100 nF ceramic.
The condition is that the error in a conversion started after tREFON or tRefBuf is less than ±0.5 LSB.
Typical Characteristics – ADC12
CVREF+
100 mF
tREFON » .6 6 x CVREF+ [m s ] w ith CVREF+ in mF
10 mF
1mF
0
1 ms
10 m s
100 m s
tREFON
Figure 39. Typical Settling Time of Internal Reference tREFON vs External Capacitor on VREF+
Copyright © 2010–2011, Texas Instruments Incorporated
61
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
From
Power
Supply
DVCC
+
DVSS
10 mF
100 nF
AVCC
+
-
MSP430F2619
AVSS
10 mF
Apply External Reference [VeREF+]
or Use Internal Reference [VREF+]
100 nF
VREF+ or VeREF+
+
10 mF
Apply
External
Reference
100 nF
VREF-/VeREF-
+
10 mF
100 nF
Figure 40. Supply Voltage and Reference Voltage Design VREF-/VeREF- External Supply
From
Power
Supply
DVCC
+
DVSS
10 mF
100 nF
AVCC
+
-
MSP430F2619
AVSS
10 mF
Apply External Reference [VeREF+]
or Use Internal Reference [VREF+]
VREF+ or VeREF+
+
10 mF
Reference Is Internally
Switched to AVSS
100 nF
100 nF
VREF-/VeREF-
Figure 41. Supply Voltage and Reference Voltage Design VREF-/VeREF- = AVSS, Internally Connected
62
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
12-Bit ADC Timing Parameters – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
MIN
TYP
MAX
UNIT
fADC12CLK
ADC12 input clock
frequency
For specified performance of ADC12 linearity
parameters
2.2 V/3 V
0.45
5
6.3
MHz
fADC12OSC
ADC12 built-in oscillator
frequency
ADC12DIV = 0,
fADC12CLK = fADC12OSC
2.2 V/3 V
3.7
5
6.3
MHz
2.2 V/3 V
2.06
Conversion time
ADC12 built-in oscillator,
CVREF+ ≥ 5 μF,
fADC12OSC = 3.7 MHz to 6.3 MHz
tCONVERT
μs
External fADC12CLK from ACLK, MCLK, or
SMCLK: ADC12SSEL ≠ 0
tADC12ON
tSample (1)
(1)
(2)
(3)
(1)
Turn-on settling time of
the ADC
See (2)
Sampling time
RS = 400 Ω, RI = 1000 Ω, CI = 30 pF,
τ = [RS + RI] x CI (3)
3.51
13 x ADC12DIV
x 1/fADC12CLK
100
3V
1220
2.2 V
1400
ns
ns
Limits verified by design
The condition is that the error in a conversion started after tADC12ON is less than ±0.5 LSB. The reference and input signal are already
settled.
Approximately ten Tau (τ) are needed to get an error of less than ±0.5 LSB: tSample = ln(2n+1) x (RS + RI) x CI+ 800 ns where n = ADC
resolution = 12, RS = external source resistance.
12-Bit ADC Linearity Parameters – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
1.4 V ≤ (VeREF+ - VREF-/VeREF-) min ≤ 1.6 V
VCC
EI
Integral linearity error
ED
Differential linearity error
(VeREF+ - VREF-/VeREF-)min ≤ (VeREF+ - VREF-/VeREF-),
CVREF+ = 10 μF (tantalum) and 100 nF (ceramic)
2.2 V/3 V
EO
Offset error
(VeREF+ - VREF-/VeREF-)min ≤ (VeREF+ - VREF-/VeREF-),
Internal impedance of source RS < 100 Ω,
CVREF+ = 10 μF (tantalum) and 100 nF (ceramic)
2.2 V/3 V
EG
Gain error
(VeREF+ - VREF-/VeREF-)min ≤ (VeREF+ - VREF-/VeREF-),
CVREF+ = 10 μF (tantalum) and 100 nF (ceramic)
ET
Total unadjusted error
(VeREF+ - VREF-/VeREF-)min ≤ (VeREF+ - VREF-/VeREF-),
CVREF+ = 10 μF (tantalum) and 100 nF (ceramic)
1.6 V < (VeREF+ - VREF-/VeREF-) min ≤ VAVCC
Copyright © 2010–2011, Texas Instruments Incorporated
MIN
TYP
MAX
±2
2.2 V/3 V
±1.7
UNIT
LSB
±1
LSB
±2
±4
LSB
2.2 V/3 V
±1.1
±2
LSB
2.2 V/3 V
±2
±5
LSB
63
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
12-Bit ADC Temperature Sensor and Built-In VMID – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
MIN
TYP
MAX
2.2 V
40
120
3V
60
160
UNIT
ISENSOR
Operating supply current into
AVCC terminal (1)
REFON = 0, INCH = 0Ah,
ADC12ON = 1, TA = 25°C
VSensor (2)
Sensor output voltage (3)
ADC12ON = 1, INCH = 0Ah,
TA = 0°C
2.2 V/3 V
986
mV
ADC12ON = 1, INCH = 0Ah
2.2 V/3 V
3.55
mV/°C
ADC12ON = 1, INCH = 0Ah,
Error of conversion result ≤ 1 LSB
2.2 V/3 V
TCSENSOR (2)
tSensor(sample)
(2)
Sample time required
if channel 10 is selected
(4)
2.2 V
NA
3V
NA
Current into divider
at channel 11 (5)
ADC12ON = 1, INCH = 0Bh
VMID
AVCC divider at channel 11
ADC12ON = 1, INCH = 0Bh,
VMID is ≉ 0.5 × VAVCC
2.2 V
tVMID(sample)
Sample time required
if channel 11 is selected
ADC12ON = 1, INCH = 0Bh,
Error of conversion result ≤ 1 LSB
2.2 V
1400
3V
1220
(1)
(2)
(3)
(4)
(5)
(6)
(6)
μs
30
IVMID
1.1
1.1±0.04
1.5 1.5 ±0.04
3V
μA
μA
V
ns
The sensor current ISENSOR is consumed if (ADC12ON = 1 and REFON = 1) or (ADC12ON = 1 and INCH = 0Ah and sample signal is
high). When REFON = 1, ISENSOR is included in IREF+. When REFON = 0, ISENSOR applies during conversion of the temperature sensor
input (INCH = 0Ah).
Limits characterized
The temperature sensor offset can be as much as ±20°C. A single-point calibration is recommended to minimize the offset error of the
built-in temperature sensor.
The typical equivalent impedance of the sensor is 51 kΩ. The sample time required includes the sensor-on time tSENSOR(on).
No additional current is needed. The VMID is used during sampling.
The on-time tVMID(on) is included in the sampling time tVMID(sample); no additional on time is needed.
12-Bit DAC Supply Specifications – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
AVCC
TEST CONDITIONS
Supply voltage range
DAC12AMPx = 2, DAC12IR = 0,
DAC12_xDAT = 0x0800
Supply current,
single DAC channel (1)
IDD
TA
VCC
AVCC = DVCC,
AVSS = DVSS = 0 V
DAC12AMPx = 5, DAC12IR = 1,
DAC12_xDAT = 0x0800,
VeREF+ = VREF+ = AVCC
PSSR
Power-supply rejection
ratio (3) (4)
DAC12_xDAT = 800h, VREF =
1.5 V or 2.5 V,
ΔAVCC = 100 mV
MAX
3.6
-55°C to 85°C
50
110
105°C
69
150
50
130
200
440
700
1500
UNIT
V
μA
2.2 V/3 V
DAC12AMPx = 7, DAC12IR = 1,
DAC12_xDAT = 0x0800,
VeREF+ = VREF+ = AVCC
DAC12_xDAT = 800h, VREF =
1.5 V,
ΔAVCC = 100 mV
TYP
2.2
DAC12AMPx = 2, DAC12IR = 1,
DAC12_xDAT = 0x0800,
VeREF+ = VREF+ = AVCC
(2)
MIN
70
2.2 V/3 V
dB
70
(1)
(2)
(3)
(4)
No load at the output pin, DAC12_0 or DAC12_1, assuming that the control bits for the shared pins are set properly.
Current into reference terminals not included. If DAC12IR = 1 current flows through the input divider; see Reference Input specifications.
PSRR = 20 × log{ΔAVCC/ΔVDAC12_xOUT}
VREF is applied externally. The internal reference is not used.
64
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
12-Bit DAC Linearity Parameters – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
Resolution
DNL
MIN
12-bit monotonic
Differential nonlinearity
VREF = 1.5 V
DAC12AMPx = 7, DAC12IR = 1
±8
±2
±8
±0.4
±1
±0.4
±1
LSB
±21
VREF = 2.5 V
DAC12AMPx = 7, DAC12IR = 1
±21
2.2 V/3 V
VREF = 1.5 V
DAC12AMPx = 7, DAC12IR = 1
Offset voltage with
calibration (1) (2)
±2
LSB
VREF = 1.5 V
DAC12AMPx = 7, DAC12IR = 1
EO
LSB
±3.5
VREF = 2.5 V
DAC12AMPx = 7, DAC12IR = 1
dE(O)/dT
Offset error temperature
coefficient (1)
EG
Gain error (1)
dE(G)/dT
Gain temperature
coefficient (1)
tOffset_Cal
Time for offset calibration (3)
±3.5
VREF = 1.5 V
±3.5
2.2 V/3 V
VREF = 2.5 V
±3.5
LSB
ppm of
FSR/°C
10
100
DAC12AMPx = 3, 5
2.2 V/3 V
32
DAC12AMPx = 4, 6, 7
(2)
(3)
µV/°C
30
DAC12AMPx = 2
(1)
UNIT
bits
2.2 V/3 V
VREF = 2.5 V
DAC12AMPx = 7, DAC12IR = 1
Offset voltage without
calibration (1) (2)
MAX
2.2 V/3 V
VREF = 2.5 V
DAC12AMPx = 7, DAC12IR = 1
(1)
TYP
12
VREF = 1.5 V
DAC12AMPx = 7, DAC12IR = 1
Integral nonlinearity (1)
INL
VCC
LSB
6
Parameters calculated from the best-fit curve from 0x0A to 0xFFF. The best-fit curve method is used to deliver coefficients “a” and “b” of
the first-order equation: y = a + b × x. VDAC12_xOUT = EO + (1 + EG) × (VeREF+/4095) × DAC12_xDAT, DAC12IR = 1.
The offset calibration works on the output operational amplifier. Offset calibration is triggered setting bit DAC12CALON.
The offset calibration can be done if DAC12AMPx = {2, 3, 4, 5, 6, 7}. The output operational amplifier is switched off with
DAC12AMPx={0, 1}.The DAC12 module should be configured prior to initiating calibration. Port activity during calibration may affect
accuracy and is not recommended.
DAC V OUT
DAC Output
V R+
R Load =
Ideal transfer
function
AV CC
2
Offset Error
C Load = 100pF
Gain Error
Positive
Negative
DAC Code
Figure 42. Linearity Test Load Conditions and Gain/Offset Definition
Copyright © 2010–2011, Texas Instruments Incorporated
65
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Typical Characteristics - 12-Bit DAC Linearity Specifications
Figure 43. TYPICAL INL ERROR
vs
DIGITAL INPUT DATA
Figure 44.
Figure 45. TYPICAL DNL ERROR
vs
DIGITAL INPUT DATA
Figure 46.
66
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
12-Bit DAC Output Specifications – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
No Load, VeREF+ = AVCC,
DAC12_xDAT = 0h, DAC12IR = 1,
DAC12AMPx = 7
Output voltage range (1)
(See Figure 47)
VO
No Load, VeREF+ = AVCC,
DAC12_xDAT = 0FFFh,
DAC12IR = 1, DAC12AMPx = 7
RLoad = 3 kΩ, VeREF+ = AVCC,
DAC12_xDAT = 0h, DAC12IR = 1,
DAC12AMPx = 7
Max DAC12 load
capacitance
IL(DAC12)
Max DAC12 load current
Output resistance
(See Figure 47)
2.2 V
3V
RLoad = 3 kΩ, VO/P(DAC12) = 0 V,
DAC12AMPx = 7, DAC12_xDAT = 0FFFh
2.2 V/3 V
RLoad = 3 kΩ,
0.3 V ≤ VO/P(DAC12) ≤ AVCC - 0.3 V,
DAC12AMPx = 7
(1)
MAX
0
0.005
AVCC 0.05
AVCC
UNIT
V
0
0.1
AVCC 0.13
AVCC
2.2 V/3 V
RLoad = 3 kΩ, VO/P(DAC12) = 0 V,
DAC12AMPx = 7, DAC12_xDAT = 0h
RO/P(DAC12)
TYP
2.2 V/3 V
RLoad = 3 kΩ, VeREF+ = AVCC,
DAC12_xDAT = 0FFFh,
DAC12IR = 1, DAC12AMPx = 7
CL(DAC12)
MIN
100
–0.5
0.5
–1
1
150
250
150
250
1
4
pF
mA
Ω
Data is valid after the offset calibration of the output amplifier.
Figure 47. DAC12_x Output Resistance Tests
Copyright © 2010–2011, Texas Instruments Incorporated
67
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
12-Bit DAC Reference Input Specifications – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
VeREF+
Ri(VREF+),
Ri(VeREF+)
(1)
(2)
(3)
(4)
(5)
68
Reference input voltage
range
Reference input
reistance
TEST CONDITIONS
DAC12IR = 0
VCC
MIN
(1) (2)
DAC12IR = 1 (3) (4)
2.2 V/3 V
TYP
MAX
AVCC/3
AVCC + 0.2
AVCC
AVCC + 0.2
DAC12_0 IR = DAC12_1 IR = 0
20
DAC12_0 IR = 1, DAC12_1 IR = 0
40
48
56
20
24
28
DAC12_0 IR = 0, DAC12_1 IR = 1
DAC12_0 IR = 0, DAC12_1 IR = 1
DAC12_0 SREFx = DAC12_1
SREFx (5)
UNIT
V
MΩ
2.2 V/3 V
kΩ
For a full-scale output, the reference input voltage can be as high as 1/3 of the maximum output voltage swing (AVCC).
The maximum voltage applied at reference input voltage terminal VeREF+ = [AVCC - VE(O)] / [3 x (1 + EG)].
For a full-scale output, the reference input voltage can be as high as the maximum output voltage swing (AVCC).
The maximum voltage applied at reference input voltage terminal VeREF+ = [AVCC - VE(O)] / (1 + EG).
When DAC12IR = 1 and DAC12SREFx = 0 or 1 for both channels, the reference input resistive dividers for each DAC are in parallel
reducing the reference input resistance.
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
12-Bit DAC Dynamic Specifications, VREF = VCC, DAC12IR = 1 – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
tON
TEST CONDITIONS
DAC12_xDAT = 800h,
ErrorV(O) < ±0.5 LSB (1)
(See Figure 48)
SR
VCC
MIN
DAC12AMPx = 0 → {2, 3, 4}
DAC12AMPx = 0 → {5, 6}
2.2 V/3 V
DAC12AMPx = 0 → 7
DAC12AMPx = 2
tS(FS)
DAC12_xDAT =
80h → F7Fh → 80h
Settling time, full scale
DAC12AMPx = 3, 5
2.2 V/3 V
DAC12AMPx = 4, 6, 7
DAC12AMPx = 2
tS(C-C)
Settling time, code to
code
DAC12_xDAT =
3F8h → 408h → 3F8h
DAC12AMPx = 3, 5
2.2 V/3 V
SR
Slew rate
DAC12AMPx = 3, 5
2.2 V/3 V
DAC12AMPx = 4, 6, 7
DAC12AMPx = 3, 5
DAC12AMPx = {5, 6}, DAC12SREFx = 2,
DAC12IR = 1, DAC12_xDAT = 800h
(1)
(2)
(3)
200
40
80
15
30
μs
μs
μs
0.35
0.7
1.5
2.7
V/μs
600
150
nV-s
30
40
2.2 V/3 V
DAC12AMPx = 7, DAC12SREFx = 2,
DAC12IR = 1, DAC12_xDAT = 800h
180
kHz
550
DAC12_0DAT = 800h, No load,
DAC12_1DAT = 80h ↔ F7Fh, RLoad = 3 kΩ,
fDAC12_1OUT = 10 kHz, Duty cycle = 50%
Channel-to-channel
crosstalk (3)
(See Figure 51)
100
0.12
DAC12AMPx = 4, 6, 7
BW-3dB
12
0.05
2.2 V/3 V
DAC12AMPx = {2, 3, 4}, DAC12SREFx = 2,
DAC12IR = 1, DAC12_xDAT = 800h
3-dB bandwidth,
VDC = 1.5 V,
VAC = 0.1 VPP
(See Figure 50)
30
6
2
DAC12AMPx = 2
DAC12_xDAT =
80h → F7Fh → 80h
Glitch energy, full scale
120
15
1
DAC12AMPx = 2
DAC12_xDAT =
80h → F7Fh → 80h
60
UNIT
5
DAC12AMPx = 4, 6, 7
(2)
TYP MAX
DAC12_0DAT = 80h ↔ F7Fh, RLoad = 3 kΩ,
DAC12_1DAT = 800h, No load,
fDAC12_0OUT = 10 kHz, Duty cycle = 50%
–80
2.2 V/3 V
dB
–80
RLoad and CLoad are connected to AVSS (not AVCC/2) in Figure 48.
Slew rate applies to output voltage steps ≥ 200 mV.
RLOAD = 3 kΩ, CLOAD = 100 pF
Conversion 1
V OUT
DAC Output
I Load
R Load = 3 k W
Glitch
Energy
Conversion 2
Conversion 3
+/- 1/2 LSB
AV CC
2
R O/P(DAC12.x)
+/- 1/2 LSB
C Load = 100pF
tsettleLH
tsettleHL
Figure 48. Settling Time and Glitch Energy Testing
Copyright © 2010–2011, Texas Instruments Incorporated
69
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Conversion 1
Conversion 2
Conversion 3
V OUT
90%
90%
10%
10%
tSRLH
tSRHL
Figure 49. Slew Rate Testing
I Load
Ve REF+
R Load = 3 k W
AV CC
DAC12_x
2
DACx
AC
C Load = 100pF
DC
Figure 50. Test Conditions for 3-dB Bandwidth Specification
I Load
R Load
AV CC
DAC12_0
2
DAC0
DAC12_xDAT
080h
7F7h
080h
7F7h
080h
V OUT
C Load = 100pF
VREF+
I Load
V DAC12_yOUT
R Load
AV CC
DAC12_1
V DAC12_xOUT
2
DAC1
fToggle
C Load = 100pF
Figure 51. Crosstalk Test Conditions
70
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Flash Memory – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST
CONDITIONS
VCC
MIN
TYP
MAX
UNIT
VCC(PGM/ERASE)
Program and erase supply voltage
2.2
3.6
V
fFTG
Flash timing generator frequency
257
476
kHz
IPGM
Supply current from VCC during program
5
mA
IERASE
Supply current from VCC during erase
7
mA
tCPT
Cumulative program time
10
ms
tCMErase
Cumulative mass erase time
See
(1)
2.2 V/3.6 V
3
2.2 V/3.6 V
3
2.2 V/3.6 V
2.2 V/3.6 V
20
4
Program/Erase endurance
10
ms
5
10
cycles
tRetention
Data retention duration
TJ = 25°C
tWord
Word or byte program time
See (2)
35
tFTG
tBlock,
0
Block program time for 1st byte or word
See (2)
30
tFTG
tBlock,
1-63
Block program time for each additional byte or
word
See (2)
21
tFTG
tBlock,
End
Block program end-sequence wait time
See (2)
6
tFTG
(2)
10593
tFTG
4819
tFTG
tMass Erase
Mass erase time
See
tSeg Erase
Segment erase time
See (2)
(1)
(2)
100
years
The cumulative program time must not be exceeded when writing to a 64-byte flash block. This parameter applies to all programming
methods: individual word/byte write and block write modes.
These values are hardwired into the Flash Controller's state machine (tFTG = 1/fFTG).
30
25
Time - (Yrs)
20
15
10
5
0
85
90
95
100
105
110
115
120
125
130
135
140
145
150
Junction Temperature - T J (C)
Figure 52. Flash Data Retention vs Junction Temperature
Copyright © 2010–2011, Texas Instruments Incorporated
71
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
RAM – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
V(RAMh)
(1)
RAM retention supply voltage
TEST CONDITIONS
(1)
MIN
CPU halted
MAX
1.6
UNIT
V
This parameter defines the minimum supply voltage VCC when the data in RAM remains unchanged. No program execution should
happen during this supply voltage condition.
JTAG and Spy-Bi-Wire Interface – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
fTCK
TCK input frequency
See
(1)
RInternal
Internal pulldown resistance on TEST
See
(2)
(1)
(2)
VCC
MIN
TYP
MAX
2.2 V
0
5
3V
0
10
2.2 V/3 V
25
60
90
UNIT
MHz
kΩ
fTCK may be restricted to meet the timing requirements of the module selected.
TMS, TDI/TCLK, and TCK pullup resistors are implemented in all versions.
JTAG Fuse (1) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
VCC(FB)
Supply voltage during fuse-blow condition
VFB
Voltage level on TEST for fuse blow
IFB
Supply current into TEST during fuse blow
tFB
Time to blow fuse
(1)
72
TEST CONDITIONS
TA = 25°C
MIN
MAX
2.5
6
UNIT
V
7
V
100
mA
1
ms
Once the fuse is blown, no further access to the MSP430 JTAG/Test and emulation features is possible. The JTAG block is switched to
bypass mode.
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
APPLICATION INFORMATION
Port P1 Pin Schematic: P1.0 to P1.7, Input/Output With Schmitt Trigger
Pad Logic
P1REN.x
P1DIR.x
0
P1OUT.x
0
1
0
DVCC
1
1
Direction
0: Input
1: Output
1
Module X OUT
DVSS
P1.0/TACLK/CAOUT
P1.1/TA0
P1.2/TA1
P1.3/TA2
P1.4/SMCLK
P1.5/TA0
P1.6/TA1
P1.7/TA2
P1SEL.x
P1IN.x
EN
Module X IN
D
P1IE.x
EN
P1IRQ.x
Q
Set
P1IFG.x
P1SEL.x
P1IES.x
Interrupt
Edge Select
Port P1 (P1.0 to P1.7) Pin Functions
PIN NAME (P1.X)
X
FUNCTION
P1.0
P1.0/TACLK/ADC10CLK
0
Timer_A3.TACLK
ADC10CLK
P1.1 (I/O)
P1.1/TA0
1
Timer_A3.CCI0A
Timer_A3.TA0
2
P1.4/SMCLK
P1.5/TA0
P1.6/TA1
P1.7/TA2
3
4
5
6
7
P1SEL.x
0
0
1
1
1
I: 0; O: 1
0
0
1
1
1
0
Timer_A3.CCI0A
0
1
Timer_A3.TA0
1
1
P1.3 I/O
P1.3/TA2
P1DIR.x
I: 0; O: 1
I: 0; O: 1
P1.2 (I/O)
P1.2/TA1
CONTROL BITS/SIGNALS
I: 0; O: 1
0
Timer_A3.CCI0A
0
1
Timer_A3.TA0
1
1
I: 0; O: 1
0
1
1
I: 0; O: 1
0
P1.4 (I/O)
SMCLK
P1.5 (I/O)
Timer_A3.TA0
P1.6 (I/O)
Timer_A3.TA1
P1.7 (I/O)
Timer_A3.TA2
Copyright © 2010–2011, Texas Instruments Incorporated
1
1
I: 0; O: 1
0
1
1
I: 0; O: 1
0
1
1
73
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Port P2 Pin Schematic: P2.0 to P2.4, P2.6, and P2.7, Input/Output With Schmitt Trigger
Pad Logic
To
Comparator_A
From
Comparator_A
CAPD.x
P2REN.x
0
P2DIR.x
P2OUT.x
0
1
0
DVCC
1
1
Direction
0: Input
1: Output
1
Module X OUT
DVSS
P2.0/ACLK/CA2
P2.1/TAINCLK/CA3
P2.2/CAOUT/TA0/CA4
P2.3/CA0/TA1
P2.4/CA1/TA2
P2.6/ADC12CLK/
DMAE0/CA6
P2.7/TA0/CA7
Bus
Keeper
EN
P2SEL.x
P2IN.x
EN
D
Module X IN
P2IE.x
EN
P2IRQ.x
Q
Set
P2IFG.x
P2SEL.x
P2IES.x
Interrupt
Edge Select
Port P2.0, P2.3, P2.4, P2.6 and P2.7 Pin Functions
Pin Name (P2.X)
P2.0/ACLK/CA2
P2.1/TAINCLK/CA3
P2.2/CAOUT/TA0/CA4
P2.3/CA0/TA1
(1)
74
X
0
1
2
3
FUNCTION
CONTROL BITS/SIGNALS (1)
CAPD.x
P2DIR.x
P2SEL.x
P2.0 (I/O)
0
I: 0; O: 1
0
ACLK
0
1
1
CA2
1
X
X
P2.2 (I/O)
0
I: 0; O: 1
0
Timer_A3.INCLK
0
0
1
DVSS
0
1
1
CA3
1
X
X
P2.2 (I/O)
0
I: 0; O: 1
0
CAOUT
0
1
1
Timer_A3.CCI0B
0
0
1
CA4
1
X
X
P2.3 (I/O)
0
I: 0; O: 1
0
Timer_A3.TA1
0
1
1
CA0
1
X
X
X: Don't care
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Pin Name (P2.X)
X
P2.4/CA1/TA2
FUNCTION
4
P2.6/ADC12CLK/
DMAE0/CA6
6
P2.7/TA0/CA7
7
CONTROL BITS/SIGNALS (1)
CAPD.x
P2DIR.x
P2SEL.x
P2.4 (I/O)
0
I: 0; O: 1
0
Timer_A3.TA2
0
1
X
CA1
1
X
1
P2.6 (I/O)
0
I: 0; O: 1
0
ADC12CLK
0
1
1
DMAE0
0
0
1
CA6
1
X
X
P2.7 (I/O)
0
I: 0; O: 1
0
Timer_A3.TA0
0
1
1
CA7
1
X
X
Port P2 Pin Schematic: P2.5, Input/Output With Schmitt Trigger and External ROSC for DCO
Pad Logic
To Comparator
From Comparator
CAPD.5
To DCO
in DCO
DCOR
P2REN.5
P2DIR.5
0
0
Module X OUT
1
0
DVCC
1
1
Direction
0: Input
1: Output
1
P2OUT.5
DVSS
P2.5/ROSC/CA5
Bus
Keeper
EN
P2SEL.x
P2IN.5
EN
Module X IN
D
P2IE.5
P2IRQ.5
EN
Q
Set
P2IFG.5
P2SEL.5
P2IES.5
Copyright © 2010–2011, Texas Instruments Incorporated
Interrupt
Edge Select
75
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Port P2 (P2.5) Pin Functions
PIN NAME (P2.X)
X
CONTROL BITS/SIGNALS (1)
FUNCTION
P2.5 (I/O)
P2.5/ROSC /CA5
(1)
(2)
5
ROSC
(2)
CAPD
DCOR
P2DIR.5
P2SEL.5
0
0
I: 0; O: 1
0
X
0
1
X
DVSS
0
0
1
1
ROSC
1 or selected
0
X
X
X: Don't care
If ROSC is used it is connected to an external resistor.
Port P3 Pin Schematic: P3.0 to P3.7, Input/Output With Schmitt Trigger
Pad Logic
P3REN.x
P3DIR.x
Module
direction
P3OUT.x
Module X OUT
0
DVSS
0
DVCC
1
1
0
1
P3.0/UCB0STE/UCA0CLK
P3.1/UCB0SIMO/UCB0SDA
P3.2/UCB0SOMI/UCB0SCL
P3.3/UCB0CLK/UCA0STE
P3.4/UCA0TXD/UCA0SIMO
P3.5/UCA0RXD/UCA0SOMI
P3.6/UCA1TXD/UCA1SIMO
P3.7/UCA1RXD/UCA1SOMI
P3SEL.x
P3IN.x
EN
Module X IN
1
Direction
0: Input
1: Output
D
Port P3 (P3.0) Pin Functions
PIN NAME (P3.X)
P3.0/UCB0STE/UCA0CLK
X
0
P3.1/UCB0SIMO/UCB0SDA
1
P3.2/UCB0SOMI/UCB0SCL
2
P3.3/UCB0CLK/UCA0STE
3
P3.4/UCA0TXD/UCA0SIMO
4
P3.5/UCA0RXD/UCA0SOMI
5
P3.6/UCA1TXD/UCA1SIMO
6
P3.7/UCA1RXD/UCA1SOMI
7
(1)
(2)
(3)
(4)
76
FUNCTION
P3.0 (I/O)
UCB0STE/UCA0CLK
(2) (3)
P3.1 (I/O)
UCB0SIMO/UCB0SDA (2) (4)
P3.2 (I/O
UCB0SOMI/UCB0SCL (2) (4)
P3.3 (I/O)
UCB0CLK/UCA0STE (2)
P3.4 (I/O)
UCA0TXD/UCA0SIMO (2)
P3.5 (I/O)
UCA0RXD/UCA0SOMI
(2)
P3.6 (I/O)
UCA1TXD/UCA1SIMO (2)
P3.7 (I/O)
UCA1RXD/UCA1SOMI (2)
CONTROL BITS/SIGNALS (1)
P3DIR.x
P3SEL.x
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
X: Don’t care
The pin direction is controlled by the USCI module.
UCA0CLK function takes precedence over UCB0STE function. If the pin is required as UCA0CLK input or output, USCI A0/B0 is forced
to 3-wire SPI mode if 4-wire SPI mode is selected.
In case the I2C functionality is selected the output drives only the logical 0 to VSS level.
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Port P4 Pin Schematic: P4.0 to P4.7, Input/Output With Schmitt Trigger
Pad Logic
P4REN.x
P4DIR.x
0
P4OUT.x
0
1
0
DVCC
1
1
Direction
0: Input
1: Output
1
Module X OUT
DVSS
P4.0/TB0
P4.1/TB1
P4.2/TB2
P4.3/TB3
P4.4/TB4
P4.5/TB5
P4.6/TB6
P4.7/TBCLK
P4SEL.x
P4IN.x
EN
Module X IN
D
Port P4 (P4.0 to P4.7) Pin Functions
PIN NAME (P4.X)
X
FUNCTION
P4SEL.x
I: 0; O: 1
0
Timer_B7.CCI0A and Timer_B7.CCI0B
0
1
Timer_B7.TB0
1
1
I: 0; O: 1
0
0
1
P4.0 (I/O)
P4.0/TB0
0
P4.1 (I/O)
P4.1/TB1
1
Timer_B7.CCI1A and Timer_B7.CCI1B
Timer_B7.TB1
P4.2 (I/O)
P4.2/TB2
2
Timer_B7.CCI2A and Timer_B7.CCI2B
Timer_B7.TB2
P4.3 (I/O)
P4.3/TB3
3
Timer_B7.CCI3A and Timer_B7.CCI3B
Timer_B7.TB3
4
5
P4.7/TBCLK
6
7
0
0
1
1
1
I: 0; O: 1
0
0
1
1
0
Timer_B7.CCI4A and Timer_B7.CCI4B
0
1
Timer_B7.TB4
1
1
I: 0; O: 1
0
Timer_B7.CCI5A and Timer_B7.CCI5B
0
1
Timer_B7.TB5
1
1
P4.6 (I/O)
P4.6/TB6
1
1
P4.5 (I/O)
P4.5/TB5
1
I: 0; O: 1
I: 0; O: 1
P4.4 (I/O)
P4.4/TB4
CONTROL BITS/SIGNALS
P4DIR.x
I: 0; O: 1
0
Timer_B7.CCI6A and Timer_B7.CCI6B
0
1
Timer_B7.TB6
1
1
I: 0; O: 1
0
1
1
P4.7 (I/O)
Timer_B7.TBCLK
Copyright © 2010–2011, Texas Instruments Incorporated
77
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Port P5 Pin Schematic: P5.0 to P5.7, Input/Output With Schmitt Trigger
Pad Logic
P5REN.x
P5DIR.x
0
Module
Direction
1
P5OUT.x
0
Module X OUT
DVSS
0
DVCC
1
1
Direction
0: Input
1: Output
1
P5.0/UCB1STE/UCA1CLK
P5.1/UCB1SIMO/UCB1SDA
P5.2/UCB1SOMI/UCB1SCL
P5.3/UCB1CLK/UCA1STE
P5.4/MCLK
P5.5/SMCLK
P5.6/ACLK
P5.7/TBOUTH/SVSOUT
P5SEL.x
P5IN.x
EN
Module X IN
D
Port P5 (P5.0 to P5.7) Pin Functions
PIN NAME (P5.X)
P5.0/UCB1STE/UCA1CLK
P5.1/UCB1SIMO/UCB1SDA
P5.2/UCB1SOMI/UCB1SCL
X
0
1
2
P5.3/UCB1CLK/UCA1STE
3
P5.4/MCLK
4
P5.5/SMCLK
P5.6/ACLK
P5.7/TBOUTH/SVSOUT
(1)
(2)
(3)
(4)
(5)
78
5
6
7
FUNCTION
P5.0 (I/O)
UCB1STE/UCA1CLK
(2) (3)
P5.1 (I/O)
UCB1SIMO/UCB1SDA (4) (5)
P5.2 (I/O)
UCB1SOMI/UCB1SCL
(4) (5)
P5.3 (I/O)
UCB1CLK/UCA1STE (4)
P5.0 (I/O)
MCLK
P5.1 (I/O)
SMCLK
CONTROL BITS/SIGNALS (1)
P5DIR.x
P5SEL.x
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
1
1
I: 0; O: 1
0
1
1
I: 0; O: 1
0
1
1
P5.7 (I/O)
I: 0; O: 1
0
TBOUTH
0
1
SVSOUT
1
1
P5.2 (I/O)
ACLK
X: Don’t care
The pin direction is controlled by the USCI module.
UCA1CLK function takes precedence over UCB1STE function. If the pin is required as UCA1CLK input or output USCI A1/B1 will be
forced to 3-wire SPI mode if 4-wire SPI mode is selected.
The pin direction is controlled by the USCI module.
In case the I2C functionality is selected the output drives only the logical 0 to VSS level.
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Port P6 Pin Schematic: P6.0 to P6.4, Input/Output With Schmitt Trigger
Pad Logic
ADC12 Ax
P6REN.x
P6DIR.x
0
P6OUT.x
0
1
0
DVCC
1
1
Direction
0: Input
1: Output
1
Module X OUT
DVSS
P6.0/A0
P6.1/A1
P6.2/A2
P6.3/A3
P6.4/A4
Bus
Keeper
EN
P6SEL.x
P6IN.x
EN
Module X IN
D
Port P6 (P6.0 to P6.4) Pin Functions
PIN NAME (P6.X)
X
P6.0/A0
0
P6.1/A1
1
P6.2/A2
2
P6.3/A3
3
P6.4/A4
(1)
(2)
(3)
4
FUNCTION
P6.0 (I/O)
A0 (2)
P6.1 (I/O)
A1 (3)
P6.2 (I/O)
A2 (3)
P6.3(I/O)
A3
(3)
P6.3 (I/O)
A4 (3)
CONTROL BITS/SIGNALS (1)
P6DIR.x
P6SEL.x
I: 0; O: 1
0
X
X
I: 0; O: 1
0
X
X
I: 0; O: 1
0
X
X
I: 0; O: 1
0
X
X
I: 0; O: 1
0
X
X
X: Don’t care
The ADC12 channel Ax is connected to AVss internally if not selected.
The ADC12 channel Ax is connected to AVss internally if not selected.
Copyright © 2010–2011, Texas Instruments Incorporated
79
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Port P6 Pin Schematic: P6.5 and P6.6, Input/Output With Schmitt Trigger
Pad Logic
DAC12_0OUT
DAC12AMP > 0
ADC12 Ax
ADC12 Ax
P6REN.x
P6DIR.x
0
P6OUT.x
0
1
0
DVCC
1
1
Direction
0: Input
1: Output
1
Module X OUT
DVSS
P6.5/A5/DAC1
P6.6/A6/DAC0
Bus
Keeper
EN
P6SEL.x
P6IN.x
EN
Module X IN
D
Port P6 (P6.5 to P6.6) Pin Functions
CONTROL BITS/SIGNALS (1)
PIN NAME (P6.X)
X
FUNCTION
P6.5 (I/O)
P6.5/A5/DAC1
5
(1)
(2)
(3)
(4)
(5)
80
CAPD.x or
DAC12AMP > 0
I: 0; O: 1
0
0
1
1
0
(2)
X
X
1
X
X
1
I: 0; O: 1
0
0
A5
P6.6 (I/O)
6
P6SEL.x
DVSS
DAC1 (DA12OPS = 1) (3)
P6.6/A6/DAC0
P6DIR.x
DVSS
1
1
0
A6 (4)
X
X
1
DAC1 (DA12OPS = 0) (5)
X
X
1
X: Don’t care
The ADC12 channel Ax is connected to AVss internally if not selected.
The DAC outputs are floating if not selected.
The ADC12 channel Ax is connected to AVss internally if not selected.
The DAC outputs are floating if not selected.
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Port P6 Pin Schematic: P6.7, Input/Output With Schmitt Trigger
Pad Logic
to SVS Mux
VLD = 15
DAC12_0OUT
DAC12AMP > 0
ADC12 A7
from ADC12
P6REN.7
P6DIR.7
0
P6OUT.7
0
1
0
DVCC
1
1
Direction
0: Input
1: Output
1
Module X OUT
DVSS
P6.7/A7/DAC1/SVSIN
Bus
Keeper
EN
P6SEL.7
P6IN.7
EN
Module X IN
D
Port P6 (P6.7) Pin Functions
PIN NAME (P6.X)
X
FUNCTION
P6.7 (I/O)
P6.7/A7/DAC1/SVSIN
(1)
(2)
(3)
7
CONTROL BITS/SIGNALS (1)
P6DIR.x
P6SEL.x
I: 0; O: 1
0
DVSS
1
1
A7 (2)
X
X
DAC1 (DA12OPS = 0) (3)
X
X
SVSIN (VLD = 15)
X
X
X: Don’t care
The ADC12 channel Ax is connected to AVss internally if not selected.
The DAC outputs are floating if not selected.
Copyright © 2010–2011, Texas Instruments Incorporated
81
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Port P7 Pin Schematic: P7.0 to P7.7, Input/Output With Schmitt Trigger
Pad Logic
P7REN.x
P7DIR.x
0
0
1
P7OUT.x
0
VSS
1
DVSS
0
DVCC
1
1
Direction
0: Input
1: Output
P7.x
P7SEL.x
P7IN.x
EN
Module X IN
D
Port P7 (P7.0 to P7.7) Pin Functions (4)
PIN NAME (P7.X)
P7.0
X
0
P7.1
1
P7.2
2
P7.3
3
P7.4
4
P7.5
5
P7.6
6
P7.7
7
(4)
82
FUNCTION
P7.0 (I/O)
Input
P7.1 (I/O)
Input
P7.2 (I/O)
Input
P7.3 (I/O)
Input
P7.4 (I/O)
Input
P7.5 (I/O)
Input
P7.6 (I/O)
Input
P7.7 (I/O)
Input
CONTROL BITS/SIGNALS
P7DIR.x
P7SEL.x
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
KGD only
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Port P8 Pin Schematic: P8.0 to P8.5, Input/Output With Schmitt Trigger
Pad Logic
P8REN.x
P8DIR.x
0
0
1
P8OUT.x
0
VSS
1
DVSS
0
DVCC
1
1
Direction
0: Input
1: Output
P8.0
P8.1
P8.2
P8.3
P8.4
P8.5
P8SEL.x
P8IN.x
EN
Module X IN
D
Port P8 (P8.0 to P8.5) Pin Functions (1)
PIN NAME (P8.X)
P8.0
X
0
P8.1
1
P8.2
2
P8.3
3
P8.4
4
P8.5
5
(1)
FUNCTION
P8.0 (I/O)
Input
P8.1 (I/O)
Input
P8.2 (I/O)
Input
P8.3 (I/O)
Input
P8.4 (I/O)
Input
P8.5 (I/O)
Input
CONTROL BITS/SIGNALS
P8DIR.x
P8SEL.x
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
KGD only
Copyright © 2010–2011, Texas Instruments Incorporated
83
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Port P8 Pin Schematic: P8.6, Input/Output With Schmitt Trigger
BCSCTL3.XT2Sx = 11
0
XT2CLK
From
P8.7/XIN
1
P8.7/XIN
XT2 off
Pad Logic
P8SEL.7
P8REN.6
P8DIR.6
0
0
Module X OUT
1
0
DVCC
1
1
Direction
0: Input
1: Output
1
P8OUT.6
DVSS
P8.6/XOUT
Bus
Keeper
EN
P8SEL.6
P8IN.6
EN
Module X IN
D
Port P8 (P8.6) Pin Functions (1)
PIN NAME (P8.X)
X
FUNCTION
P8DIR.x
P8SEL.x
I: 0; O: 1
0
XOUT (default)
0
1
DVSS
1
1
P8.6 (I/O)
P8.6/XOUT
(1)
84
6
CONTROL BITS/SIGNALS
KGD only
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
Port P8 Pin Schematic: P8.7, Input/Output With Schmitt Trigger
BCSCTL3.XT2Sx = 11
P8.6/XOUT
XT2 off
0
XT2CLK
1
P8SEL.6
Pad Logic
P8REN.7
0
P8DIR.7
0
P8OUT.7
0
1
0
DVCC
1
1
Direction
0: Input
1: Output
1
Module X OUT
DVSS
P8.7/XIN
Bus
Keeper
EN
P8SEL.7
P8IN.7
EN
Module X IN
D
Port P8 (P8.7) Pin Functions (1)
PIN NAME (P8.X)
X
FUNCTION
P8.7 (I/O)
P8.7/XIN
(1)
6
CONTROL BITS/SIGNALS
P8DIR.x
P8SEL.x
I: 0; O: 1
0
XIN (default)
0
1
VSS
1
1
KGD only
Copyright © 2010–2011, Texas Instruments Incorporated
85
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
JTAG Pins: TMS, TCK, TDI/TCLK, TDO/TDI, Input/Output With Schmitt Trigger
TDO
Controlled by JTAG
Controlled by JTAG
JTAG
TDO/TDI
Controlled
by JTAG
DVCC
DVCC
TDI
Fuse
Burn and Test
Fuse
Test
TDI/TCLK
and
DVCC
Emulation
Module
TMS
TMS
DVCC
During Programming Activity and
During Blowing of the Fuse, Pin
TDO/TDI is Used to Apply the Test
Input Data for JTAG Circuitry
TCK
TCK
86
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430F2619S-HT
SLAS697B – MARCH 2010 – REVISED JUNE 2011
www.ti.com
JTAG Fuse Check Mode
MSP430 devices that have the fuse on the TEST terminal have a fuse check mode that tests the continuity of the
fuse the first time the JTAG port is accessed after a power-on reset (POR). When activated, a fuse check
current, ITF , of 1 mA at 3 V, 2.5 mA at 5 V can flow from the TEST pin to ground if the fuse is not burned. Care
must be taken to avoid accidentally activating the fuse check mode and increasing overall system power
consumption.
When the TEST pin is again taken low after a test or programming session, the fuse check mode and sense
currents are terminated.
Activation of the fuse check mode occurs with the first negative edge on the TMS pin after power up or if TMS is
being held low during power up. The second positive edge on the TMS pin deactivates the fuse check mode.
After deactivation, the fuse check mode remains inactive until another POR occurs. After each POR the fuse
check mode has the potential to be activated.
The fuse check current flows only when the fuse check mode is active and the TMS pin is in a low state (see
Figure 53). Therefore, the additional current flow can be prevented by holding the TMS pin high (default
condition).
Time TMS Goes Low After POR
TMS
ITF
ITEST
Figure 53. Fuse Check Mode Current
Copyright © 2010–2011, Texas Instruments Incorporated
87
PACKAGE OPTION ADDENDUM
www.ti.com
20-May-2011
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
MSP430F2619SKGD1
ACTIVE
XCEPT
KGD
0
36
TBD
MSP430F2619SPM
ACTIVE
LQFP
PM
64
1
Green (RoHS
& no Sb/Br)
Lead/
Ball Finish
Call TI
MSL Peak Temp
(3)
Samples
(Requires Login)
N / A for Pkg Type
CU NIPDAU Level-3-260C-168 HR
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
MECHANICAL DATA
MTQF008A – JANUARY 1995 – REVISED DECEMBER 1996
PM (S-PQFP-G64)
PLASTIC QUAD FLATPACK
0,27
0,17
0,50
0,08 M
33
48
49
32
64
17
0,13 NOM
1
16
7,50 TYP
Gage Plane
10,20
SQ
9,80
12,20
SQ
11,80
0,25
0,05 MIN
0°– 7°
0,75
0,45
1,45
1,35
Seating Plane
0,08
1,60 MAX
4040152 / C 11/96
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Falls within JEDEC MS-026
May also be thermally enhanced plastic with leads connected to the die pads.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and
Automotive
www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
Wireless
www.ti.com/wireless-apps
RF/IF and ZigBee® Solutions
www.ti.com/lprf
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated