APR3011/2/3 MicroPower Microprocessor Reset Circuit Features • • • • General Description The APR3011/2/3 are designed to monitor voltage supplies in µP and digital systems. The quiescent current is 1.2V to 6V Input Voltage Range Low Quiescent Current : Less than 1.5 µA extremely low, typically 1.5µA, making it ideal for portable battery operated equipment. The APR3011/2/3 operate High Accuracy Detection Threshold : ±1.5% by monitoring the system power supply voltage. When the input voltage drops below a fixed threshold, the de- Fixed Trimmed Reset Thresholds for 1.5V, 1.75V, 2.32V, 2.63V, 2.93V, 3.08V, 3.9V, 4.38V, 4.63V • • vice asserts a reset signal for a fixed time period after Vcc rises above the fixed threshold. The APR3011/2/3 series Reset Timeout Period 250ms are available with three output stage versions: APR3011 push-pull active low output, APR3012 push-pull active Available Output Configurations - Open-Drain Output - CMOS Active High Output high output, and APR3013 open drain active low output. They are also designed to reject fast line transient glitches - CMOS Active Low Output • • • on VCC. The APR3011/2/3 come in a miniature SOT-23-3, SOT-23-5, and SOT-89 packages. SOT-23-3, SOT-23-5, and SOT-89 Packages No External Components Lead Free and Green Devices Available Pin Configuration (RoHS Compliant) Applications VCC NC 3 • • • • 1 Computers 5 2 1 GND Reset (3011/3) Reset (3012) Cell Phones Portable Electronics NC SOT-23-3 (Top View) 4 2 3 G N D V C C Reset (3011/3) Reset (3012) SOT-23-5 (Top View) µP Power Supply Monitoring 1 2 GND VCC 3 Reset (3011/3) Reset (3012) SOT-89 (Top View) ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright ANPEC Electronics Corp. Rev. A.4 - Jan., 2009 1 www.anpec.com.tw APR3011/2/3 Ordering and Marking Information APR3011/2/3 Assembly Material Handling Code Temperature Range Package Code Voltage Code APR3011/2/3 A/B : 11/2/3 X X APR3011/2/3 -15 D : Package Code A : SOT-23-3 B : SOT-23-5 D : SOT-89 Temperature Range I : -40 to 85 oC Handling Code TR : Tape & Reel Voltage Code : 15 : 1.5V ~ 46 : 4.63V Assembly Material G : Halogen and Lead Free Device Date Code Voltage Code A:1.5V B:1.75V C:2.32V D:2.63V E:2.93V F:3.08V G:3.9V H:4.38V J:4.63V APR3011/2/3 XXXXX 15 XXXXX - Date Code ; 15 - 1.5V Note: ANPEC lead-free products contain molding compounds/die attach materials and 100% matte tin plate termination finish; which are fully compliant with RoHS. ANPEC lead-free products meet or exceed the lead-free requirements of IPC/JEDEC J-STD-020C for MSL classification at lead-free peak reflow temperature. ANPEC defines “Green” to mean lead-free (RoHS compliant) and halogen free (Br or Cl does not exceed 900ppm by weight in homogeneous material and total of Br and Cl does not exceed 1500ppm by weight). Absolute Maximum Ratings Symbol VCC Parameter VCC to GND RESET to GND (Push-Pull Output) Rating Unit -0.3 to 6 V -0.3 to VCC +0.3 VRESET IMAX IRESET dVCC/dt V RESET to GND (Open Drain Output) -0.3 to 6 Maximum Continuous Input Current 20 mA RESET/RESET Current 20 mA Rate of Rise of VCC 100 V/µs -40 to 150 °C 260 °C TJ Junction Temperature Range TL Lead Temperature Soldering, 10 Seconds RTH,JA PD Thermal Resistance – Junction to Ambient SOT-23-3 357 SOT-23-5 357 SOT-89 180 Power Dissipation °C/W Internally Limited W Part Number Description PART NUMBER PART DESCRIPTION APR3011 Reset Output Push Pull Active Low with Delay APR3012 Reset Output Push Pull Active High with Delay APR3013 Reset Output Open Drain Active Low with Delay Copyright ANPEC Electronics Corp. Rev. A.4 - Jan., 2009 2 www.anpec.com.tw APR3011/2/3 Electrical Characteristics VIN = 5V, TA = -40 to 85°C unless otherwise noted. Typical values are at TA=25°C, VCC = 5V for 4.38V versions, VCC = 3.3V for 3.08/ 2.93V versions, VCC = 3.0V for 2.63V. versions and VCC = 2.5V for 2.32V versions, VCC = 2.0V for 1.75V versions , VCC = 1.8V for 1.5V versions. APR3011/2/3 Symbol Parameter VCC Supply Voltage ICC Supply Current VTH Test Conditions Unit Min. Typ. Max. 1.2 - 6 V VCC=1.5V~6V - 1.5 4 µA TA=-40 to 85°C - 3 5 TA=25°C - ±1.5% - TA=-40 to 85°C - ±2% - - 20 - mV 150 250 350 ms - - 0.5 V 0.8*VCC - - - 25 - µS - - 0.5 µA Reset Threshold VHYST Hysteresis Range TRTP Reset Timeout Period VOL Reset Output Low ISINK=1.2mA VOH Reset Output High ISOURCE=0.6mA TD VCC to Reset Delay VCC=VTH to (VTH-100mV) ILE Reset Output Leakage Pin Description (Note 1) PIN FUNCTION NO. NAME 1 GND Ground connection RESET RESET output remains low while VCC is below the reset threshold and remains so for a fixed time (APR3011/3) period after VCC raises above the reset threshold 2 RESET RESET output remains high while VCC is below the reset threshold and remains so for a fixed time (APR3012) period after VCC raises above the reset threshold. 3 VCC Supply Voltage (+1.2V to +6V) Note 1: The pin sequence here might not be correct for all different package types, and please refer pin configuration in page1 for correct pin assignment. Typical Application Circuit VCC VCC VCC 100k APR3013 RESET GND Copyright ANPEC Electronics Corp. Rev. A.4 - Jan., 2009 VCC VCC RESET µP INPUT APR3011 RESET APR3012 (RESET) GND GND 3 VCC RESET µP INPUT GND www.anpec.com.tw APR3011/2/3 Block Diagram VCC Reset Generator + Timer RESET Oscillator VREF APR3011 GND VCC Reset Generator + Timer RESET Oscillator VREF APR3012 GND RESET VCC Reset Generator + Timer Oscillator VREF GND Copyright ANPEC Electronics Corp. Rev. A.4 - Jan., 2009 APR3013 4 www.anpec.com.tw APR3011/2/3 Timing Chart Reset Threshold Reset Threshold Vcc (APR3012) RESET Reset Timeout Period 250ms Vcc to Reset Delay 25us (APR3011/3) RESET Copyright ANPEC Electronics Corp. Rev. A.4 - Jan., 2009 5 www.anpec.com.tw APR3011/2/3 Typical Operating Characteristics Maximum Transient Duration vs. Reset Threshold Overdrive VTH - VCC Supply Current vs. Supply Voltage 2 Maximum Transient Duration (µs) 120 Supply Current (µA) 1.6 1.2 0.8 0.4 0 100 generate a reset signal 80 60 40 20 never generate a reset signal 0 0 1 2 3 4 5 10 6 1000 Reset Threshold Overdrive VTH - VCC (mV) Supply Voltage (V) Output Source Current vs. Reset High Output Voltage Output Sink Current vs. Reset Low Output Voltage 50 70 Vcc=5V Output Sink Current (mA) 50 Vcc=4V 40 30 Vcc=2.9V 45 60 Output Source Current (mA) 100 Vcc=3V V 20 10 40 35 Vcc=2.5V 30 25 Vcc=2V 20 15 Vcc=1.5 V 10 5 0 0 0 1 2 3 4 5 0 6 Reset High Output Voltage (V) Copyright ANPEC Electronics Corp. Rev. A.4 - Jan., 2009 1 2 3 4 5 6 Reset Low Output Voltage (V) 6 www.anpec.com.tw APR3011/2/3 Typical Operating Characteristics (Cont.) Reset Propagation Delay vs. Temperature Normalized Reset Threshold vs. Temperature 60 1.008 Reset Propagation Delay (µs) Normalized Reset Threshold (%) 1.006 1.004 1.002 1 0.998 0.996 50 40 VOD=100mV 30 20 10 0 0.994 -40 -20 0 20 40 60 80 -40 100 120 -20 0 40 60 80 100 120 Temperature (°C) Temperature (°C) Supply Current vs. Temperature Reset Timeout Period vs. Temperature 600 3.5 500 3 Supply Current (µA) Reset Timeout Period (ms) 20 400 300 200 100 2.5 Vcc=5V 2 1.5 Vcc=3V 1 0.5 0 0 -40 -20 0 20 40 60 80 100 120 -40 Temperature (°C) Copyright ANPEC Electronics Corp. Rev. A.4 - Jan., 2009 -20 0 20 40 60 80 100 120 Temperature (°C) 7 www.anpec.com.tw APR3011/2/3 Typical Operating Characteristics (Cont.) Power Up Power Down Vcc(2V/div) Vcc(2V/div) RESET(2V/div) RESET(2V/div) Time (50ms/div) Time (200ms/div) Vcc to RESET Delay Vcc(0.5V/div) Vcc=VTH to (VTH-100mV) RESET(2V/div) Time (10µs/div) Copyright ANPEC Electronics Corp. Rev. A.4 - Jan., 2009 8 www.anpec.com.tw APR3011/2/3 Application Information VCC VCC Transient Rejection The APR3011/2/3 have the function to reject the transient glitches from the power line. The Maximum Transient Duration vs. Reset Threshold Overdrive shows at Typical VCC Characteristics.The transient voltage with the duration under the curve will not generate a reset signal, e.g. a RESET transient of 100mV below the reset threshold voltage has the duration more than 35µs, it will generate a reset signal. Connect a 0.1µF bypass capacitor to the VCC pin can improve the transient immunity. 100K GND Reset Output The APR3011/2/3 have 3 output stage versions: APR3001 Figure 1. Ensuring RESET Valid to VCC = 0 V is an active low push-pull output. When the VCC drops below the reset threshold, the RESET output generates a low signal. APR3012 is an active high push-pull output. When the VCC drops below the reset threshold, the RE- +3.3V +5.0V output must be connected a pull-up resistor to a supply voltage that is lower than 6V, it suits to use in multiple VCC VCC voltage systems (see Figure 2). The APR3011 RESET output is valid until the VCC=1.2V; when it is below 1.2V, APR3013 SET output generates a high signal (see Timing Chart). APR3013 is an active low open drain output, the RESET RESET the IC is shutdown, and the output becomes a floating state. If it is a trouble, a resistor should be connected GND from reset output to the ground to keep the reset output low (see Figure 1). For the APR3012, a pull-up resistor to VCC is required to keep the valid reset output for VCC below 1.2V. Copyright ANPEC Electronics Corp. Rev. A.4 - Jan., 2009 100K RESET 5V INPUT System GND Figure 2. APR3013 Open Drain Output with Multiple Supplies 9 www.anpec.com.tw APR3011/2/3 Package Information SOT-23-3 D e E E1 SEE VIEW A c b 0.25 A L GAUGE PLANE SEATING PLANE 0 A1 A2 e1 VIEW A S Y M B O L SOT-23-3 MIN. MIN. MAX. A A1 INCHES MILLIMETERS MAX. 1.45 0.00 0.057 0.15 0.000 0.006 0.051 A2 0.90 1.30 0.035 b 0.30 0.50 0.012 0.020 c 0.08 0.22 0.003 0.009 D 2.70 3.10 0.106 0.122 E 2.60 3.00 0.102 0.118 E1 1.40 1.80 0.055 e 0.95 BSC e1 0.071 0.037 BSC 1.90 BSC 0.075 BSC L 0.30 0.60 0 0° 8° 0.012 0° 0.024 8° Note : Dimension D and E1 do not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 10 mil per side. Copyright ANPEC Electronics Corp. Rev. A.4 - Jan., 2009 10 www.anpec.com.tw APR3011/2/3 Package Information SOT-23-5 D e E E1 SEE VIEW A b c 0.25 A L 0 GAUGE PLANE SEATING PLANE A1 A2 e1 VIEW A S Y M B O L SOT-23-5 INCHES MILLIMETERS MIN. MIN. MAX. A MAX. 1.45 0.057 A1 0.00 0.15 0.000 0.006 A2 0.90 1.30 0.035 0.051 b 0.30 0.50 0.012 0.020 c 0.08 0.22 0.003 0.009 D 2.70 3.10 0.106 0.122 E 2.60 3.00 0.102 0.118 E1 1.40 1.80 0.055 0.071 e 0.95 BSC 0.037 BSC e1 1.90 BSC 0.075 BSC L 0.30 0.60 0 0° 8° 0.012 0° 0.024 8° Note : 1. Follow JEDEC TO-178 AA. 2. Dimension D and E1 do not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 10 mil per side. Copyright ANPEC Electronics Corp. Rev. A.4 - Jan., 2009 11 www.anpec.com.tw APR3011/2/3 Package Information SOT-89 A C L H E E1 D D1 e e1 B B1 SOT-89 S Y M B O L A MIN. MAX. MIN. MAX. 1.40 1.60 0.055 0.063 MILLIMETERS INCHES B 0.44 0.56 0.017 0.022 B1 0.36 0.48 0.014 0.019 C 0.35 0.44 0.014 0.017 D 4.40 4.60 0.173 0.181 D1 1.62 1.83 0.064 0.072 E 2.29 2.60 0.090 0.102 E1 2.13 2.29 0.084 0.090 e 1.50 BSC e1 3.00 BSC 0.059 BSC 0.118 BSC H 3.94 4.25 0.155 L 0.89 1.20 0.035 0.167 0.047 Note : Follow JEDEC TO-243 AA. Copyright ANPEC Electronics Corp. Rev. A.4 - Jan., 2009 12 www.anpec.com.tw APR3011/2/3 Carrier Tape & Reel Dimensions P0 P2 P1 A B0 W F E1 OD0 K0 A0 A OD1 B B T SECTION A-A SECTION B-B H A d T1 Application SOT-23-3 Application SOT-23-5 Application SOT- 89 A H T1 C d D W E1 F 178.0±2.00 50 MIN. 8.4+2.00 -0.00 13.0+0.50 -0.20 1.5 MIN. 20.2 MIN. 8.0±0.30 1.75±0.10 3.5±0.05 P0 P1 P2 D0 D1 T A0 B0 K0 2.0±0.05 1.5+0.10 -0.00 1.0 MIN. 0.6+0.00 -0.40 3.20±0.20 3.10±0.20 1.50±0.20 4.0±0.10 4.0±0.10 A H T1 C d D W E1 F 178.0±2.00 50 MIN. 8.4+2.00 -0.00 13.0+0.50 -0.20 1.5 MIN. 20.2 MIN. 8.0±0.30 1.75±0.10 3.5±0.05 P0 P1 P2 D0 D1 T A0 B0 K0 2.0±0.05 1.5+0.10 -0.00 1.0 MIN. 0.6+0.00 -0.40 3.20±0.20 3.10±0.20 1.50±0.20 W E1 F 4.0±0.10 4.0±0.10 A H T1 C d D 178.0±2.00 50 MIN. 12.4+2.00 -0.00 13.0+0.50 -0.20 1.5 MIN. 20.2 MIN. P0 P1 P2 D0 D1 T A0 B0 K0 4.0±0.10 8.0±0.10 2.0±0.05 1.5+0.10 -0.00 1.5 MIN. 0.6+0.00 -0.40 4.80±0.20 4.50±0.20 1.80±0.20 12.0±0.30 1.75±0.10 5.50±0.05 (mm) Copyright ANPEC Electronics Corp. Rev. A.4 - Jan., 2009 13 www.anpec.com.tw APR3011/2/3 Devices Per Unit Package Type SOT-23-3 SOT-23-5 SOT-89 Unit Tape & Reel Tape & Reel Tape & Reel Quantity 3000 3000 1000 Taping Direction Information SOT-23-3 USER DIRECTION OF FEED SOT-23-5 USER DIRECTION OF FEED SOT-89 USER DIRECTION OF FEED Copyright ANPEC Electronics Corp. Rev. A.4 - Jan., 2009 14 www.anpec.com.tw APR3011/2/3 Reflow Condition (IR/Convection or VPR Reflow) tp TP Critical Zone TL to TP Ramp-up Temperature TL tL Tsmax Tsmin Ramp-down ts Preheat 25 t 25°C to Peak Time Reliability Test Program Test item SOLDERABILITY HOLT PCT TST ESD Latch-Up Method MIL-STD-883D-2003 MIL-STD-883D-1005.7 JESD-22-B,A102 MIL-STD-883D-1011.9 MIL-STD-883D-3015.7 JESD 78 Description 245°C, 5 sec 1000 Hrs Bias @125°C 168 Hrs, 100%RH, 121°C -65°C~150°C, 200 Cycles VHBM > 2KV, VMM > 200V 10ms, 1tr > 100mA Classification Reflow Profiles Profile Feature Average ramp-up rate (TL to TP) Preheat - Temperature Min (Tsmin) - Temperature Max (Tsmax) - Time (min to max) (ts) Time maintained above: - Temperature (TL) - Time (tL) Peak/Classification Temperature (Tp) Time within 5°C of actual Peak Temperature (tp) Ramp-down Rate Time 25°C to Peak Temperature Sn-Pb Eutectic Assembly Pb-Free Assembly 3°C/second max. 3°C/second max. 100°C 150°C 60-120 seconds 150°C 200°C 60-180 seconds 183°C 60-150 seconds 217°C 60-150 seconds See table 1 See table 2 10-30 seconds 20-40 seconds 6°C/second max. 6°C/second max. 6 minutes max. 8 minutes max. Note: All temperatures refer to topside of the package. Measured on the body surface. Copyright ANPEC Electronics Corp. Rev. A.4 - Jan., 2009 15 www.anpec.com.tw APR3011/2/3 Classification Reflow Profiles (Cont.) Table 1. SnPb Eutectic Process – Package Peak Reflow Temperatures 3 3 Package Thickness <2.5 mm ≥2.5 mm Volume mm ≥350 225 +0/-5°C 225 +0/-5°C Volume mm <350 240 +0/-5°C 225 +0/-5°C Table 2. Pb-free Process – Package Classification Reflow Temperatures 3 3 3 Volume mm Volume mm Volume mm <350 350-2000 >2000 <1.6 mm 260 +0°C* 260 +0°C* 260 +0°C* 1.6 mm – 2.5 mm 260 +0°C* 250 +0°C* 245 +0°C* ≥2.5 mm 250 +0°C* 245 +0°C* 245 +0°C* * Tolerance: The device manufacturer/supplier shall assure process compatibility up to and including the stated classification temperature (this means Peak reflow temperature +0°C. For example 260°C+0°C) at the rated MSL level. Package Thickness Customer Service Anpec Electronics Corp. Head Office : No.6, Dusing 1st Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 2F, No. 11, Lane 218, Sec 2 Jhongsing Rd., Sindian City, Taipei County 23146, Taiwan Tel : 886-2-2910-3838 Fax : 886-2-2917-3838 Copyright ANPEC Electronics Corp. Rev. A.4 - Jan., 2009 16 www.anpec.com.tw