HA17358, HA17904 Series Dual Operational Amplifier Description HA17904 and HA17358 are dual operational amplifiers which, provide internal phase compensation and high gain, and mono power source operation is possible. It can be widely applied to control equipment and to general use. Features • Wide range of operating supply voltage and mono power source operation is possible. • Wide range of common mode input voltage possible to operate with an input around 0V, and output around 0V is available. • Frequency characteristics and input bias currrent are temperature compensated. Ordering Information Type No. Application Package HA17904PSJ Car use DP-8 HA17904FPJ Car use FP-8D HA17904FPK Car use HA17904PS Industrial use DP-8 HA17904FP Industrial use FP-8D HA17358 Commercial use DP-8 HA17358F Commercial use FP-8D HA17358, HA17904 Series Pin Arrangement Vout1 1 Vin(–)1 2 Vin(+)1 3 GND 4 1 – + 2 + – 8 VCC 7 Vout2 6 Vin(–)2 5 Vin(+)2 (Top View) Circuit Schematic (1/2) Q5 Vin(–) Q1 Q2 Q3 Q4 Q6 Q7 C R1 Vin(+) Vout Q11 Q10 Q8 2 Q9 Q13 Q12 HA17358, HA17904 Series Absolute Maximum Ratings (Ta = 25°C) Ratings HA17358 HA17358 F HA17904 PS HA17904 FP HA17904 PSJ HA17904 FPJ HA17904 FPK Unit 32 32 32 32 32 32 32 V I O sink 50 50 50 50 50 50 50 mA Commonmode input voltage VCM –0.3 to VCC –0.3 to VCC –0.3 to VCC –0.3 to VCC –0.3 to VCC –0.3 to VCC –0.3 to VCC V Commonmode differential voltage V ±VCC ±VCC ±VCC ±VCC ±VCC ±VCC ±VCC V Power dissipation PT 570* 1 385* 2 570* 1 385* 2 570* 1 385* 2 385* 2 mW Operating temperature range Topr –20 to +75 –20 to +75 –20 to +75 –20 to +75 –40 to +85 –40 to +85 –40 to +125 °C Storage temperature range Tstg –55 to +125 –55 to +125 –55 to +125 –55 to +125 –55 to +125 –55 to +125 –55 to +150 °C Item Symbol Supply voltage VCC Output sink current IN(diff) Notes: 1. These are the allowable values up to Ta = 55 °C. Derate by 8.3mW/°C above that temperature. 2. These are the allowable values up to Ta = 45 °C mounting on 30% wiring density glass epoxy board. Derate by 7.14mW/°C above that temeperature. 3 HA17358, HA17904 Series Electrical Characteristics 1 (VCC = +15V, Ta = 25°C) Item Symbol Min Typ Max Unit Test Conditions Input offset voltage VIO — 3 7 mV VCM = 7.5V, RS = 50Ω, Rf = 50kΩ Input offset current I IO — 5 50 nA VCM = 7.5V, IIO = | II (+) – I I (–) | Input bias current I IB — 30 250 nA VCM = 7.5V Power source rejection ratio PSRR — 93 — dB RS = 1kΩ, Rf = 100kΩ Voltage gain AVD 75 90 — dB RL = ∞, RS = 1kΩ, Rf = 100kΩ Common mode rejection ratio CMR — 80 — dB RS = 50Ω, Rf = 5kΩ Common mode input voltage range VCM (+) 13.5 — — V RS = 1kΩ, Rf = 100kΩ VCM (–) — — –0.3 V RS = 1kΩ, Rf = 100kΩ Peak-to-peak output voltage Vop-p — 13.6 — V f = 100Hz, RL = 20kΩ, RS = 1kΩ, Rf = 100kΩ Output source current Iosource 20 40 — mA VIN+ = 1V, VIN– = 0V, VOH = 10V Output sink current Iosink 10 20 — mA VIN– = 1V, VIN+ = 0V, VOL = 2.5V Output sink current Iosink 15 50 — µA VIN– = 1V, VIN+ = 0V, Vout = 200mV Supply current I CC — 0.8 2 mA VIN = GND, RL = ∞ Slew rate SR — 0.2 — V/µs RL = ∞, VCM = 7.5V, f = 1.5kHz Channel separation CS — 120 — dB f = 1kHz Note: As for the characteristic curve, refer to HA17902. Electrical Characteristics 2 (VCC = +15V, Ta =–40 to +125°C) Item Symbol Min Typ Max Unit Test Conditions Input offset voltage VIO — — 7 mV VCM = 7.5V, RS = 50Ω, RL = 50kΩ Input offset current I IO — — 200 nA VCM = 7.5V, IIO = | II (+) – I I (–) | Input bias current I IB — — 500 nA VCM = 7.5V Common mode input voltage range VCM 0 — 13.0 V RS = 1kΩ, Rf = 100kΩ Supply current I CC — — 4 mA VIN = GND, RL = ∞ Note: As for the characteristic curve, refer to HA17904FPK. 4 HA17358, HA17904 Series Package Dimensions Unit: mm 4.85 4.4 5.25 Max 5 8 1 0.75 Max *0.22 ± 0.05 0.20 ± 0.04 2.03 Max 4 0.25 6.50 +– 0.15 1.05 0.10 ± 0.10 0° – 8° 1.27 *0.42 ± 0.08 0.40 ± 0.06 0.25 0.60 +– 0.18 0.15 0.12 M *Dimension including the plating thickness Base material dimension Hitachi Code JEDEC EIAJ Mass (reference value) FP-8D — Conforms 0.10 g Unit: mm 4.85 4.4 5.25 Max 5 8 1 0.75 Max *0.22 ± 0.05 0.20 ± 0.04 2.03 Max 4 0.25 6.50 +– 0.15 1.05 1.27 *0.42 ± 0.08 0.40 ± 0.06 0.10 ± 0.10 0° – 8° 0.25 0.60 +– 0.18 0.15 0.12 M *Dimension including the plating thickness Base material dimension Hitachi Code JEDEC EIAJ Mass (reference value) FP-8D — Conforms 0.10 g 5 HA17358, HA17904 Series Cautions 1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’s patent, copyright, trademark, or other intellectual property rights for information contained in this document. Hitachi bears no responsibility for problems that may arise with third party’s rights, including intellectual property rights, in connection with use of the information contained in this document. 2. Products and product specifications may be subject to change without notice. Confirm that you have received the latest product standards or specifications before final design, purchase or use. 3. Hitachi makes every attempt to ensure that its products are of high quality and reliability. However, contact Hitachi’s sales office before using the product in an application that demands especially high quality and reliability or where its failure or malfunction may directly threaten human life or cause risk of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment or medical equipment for life support. 4. Design your application so that the product is used within the ranges guaranteed by Hitachi particularly for maximum rating, operating supply voltage range, heat radiation characteristics, installation conditions and other characteristics. Hitachi bears no responsibility for failure or damage when used beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as failsafes, so that the equipment incorporating Hitachi product does not cause bodily injury, fire or other consequential damage due to operation of the Hitachi product. 5. This product is not designed to be radiation resistant. 6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without written approval from Hitachi. 7. Contact Hitachi’s sales office for any questions regarding this document or Hitachi semiconductor products. Hitachi, Ltd. Semiconductor & Integrated Circuits. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Tel: Tokyo (03) 3270-2111 Fax: (03) 3270-5109 URL NorthAmerica : http:semiconductor.hitachi.com/ Europe : http://www.hitachi-eu.com/hel/ecg Asia (Singapore) : http://www.has.hitachi.com.sg/grp3/sicd/index.htm Asia (Taiwan) : http://www.hitachi.com.tw/E/Product/SICD_Frame.htm Asia (HongKong) : http://www.hitachi.com.hk/eng/bo/grp3/index.htm Japan : http://www.hitachi.co.jp/Sicd/indx.htm For further information write to: Hitachi Semiconductor (America) Inc. 179 East Tasman Drive, San Jose,CA 95134 Tel: <1> (408) 433-1990 Fax: <1>(408) 433-0223 Hitachi Europe GmbH Electronic components Group Dornacher Straβe 3 D-85622 Feldkirchen, Munich Germany Tel: <49> (89) 9 9180-0 Fax: <49> (89) 9 29 30 00 Hitachi Europe Ltd. Electronic Components Group. Whitebrook Park Lower Cookham Road Maidenhead Berkshire SL6 8YA, United Kingdom Tel: <44> (1628) 585000 Fax: <44> (1628) 778322 Hitachi Asia Pte. Ltd. 16 Collyer Quay #20-00 Hitachi Tower Singapore 049318 Tel: 535-2100 Fax: 535-1533 Hitachi Asia Ltd. Taipei Branch Office 3F, Hung Kuo Building. No.167, Tun-Hwa North Road, Taipei (105) Tel: <886> (2) 2718-3666 Fax: <886> (2) 2718-8180 Hitachi Asia (Hong Kong) Ltd. Group III (Electronic Components) 7/F., North Tower, World Finance Centre, Harbour City, Canton Road, Tsim Sha Tsui, Kowloon, Hong Kong Tel: <852> (2) 735 9218 Fax: <852> (2) 730 0281 Telex: 40815 HITEC HX Copyright ' Hitachi, Ltd., 1998. All rights reserved. Printed in Japan. 6