a FEATURES Specified for VDD of 3 V to 5.5 V AD7858—200 kSPS; AD7858L—100 kSPS System and Self-Calibration with Autocalibration on Power-Up Eight Single-Ended or Four Pseudo-Differential Inputs Low Power AD7858: 12 mW (VDD = 3 V) AD7858L: 4.5 mW (V DD = 3 V) Automatic Power-Down After Conversion (25 W) Flexible Serial Interface: 8051/SPI™/QSPI™/P Compatible 24-Lead DIP, SOIC, and SSOP Packages APPLICATIONS Battery-Powered Systems (Personal Digital Assistants, Medical Instruments, Mobile Communications) Pen Computers Instrumentation and Control Systems High-Speed Modems GENERAL DESCRIPTION The AD7858/AD7858L are high-speed, low-power, 12-bit ADCs that operate from a single 3 V or 5 V power supply, the AD7858 being optimized for speed and the AD7858L for low power. The ADC powers up with a set of default conditions at which time it can be operated as a read-only ADC. The ADC contains self-calibration and system calibration options to ensure accurate operation over time and temperature and have a number of power-down options for low-power applications. The part powers up with a set of default conditions and can operate as a read-only ADC. The AD7858 is capable of 200 kHz throughput rate while the AD7858L is capable of 100 kHz throughput rate. The input track-and-hold acquires a signal in 500 ns and features a pseudo-differential sampling scheme. The AD7858/AD7858L voltage range is 0 to VREF with straight binary output coding. Input signal range is to the supply and the part is capable of converting full power signals to 100 kHz. CMOS construction ensures low power dissipation of typically 4.5 mW for normal operation and 1.15 mW in power-down mode with a throughput rate of 10 kSPS (VDD = 3 V). The part is available in 24-lead, 0.3 inch-wide dual-in-line package (DIP), 24-lead small outline (SOIC), and 24-lead small shrink outline (SSOP) packages. 3 V to 5 V Single Supply, 200 kSPS 8-Channel, 12-Bit Sampling ADC AD7858/AD7858L* FUNCTIONAL BLOCK DIAGRAM AVDD AGND AIN1 I/P MUX AD7858/ AD7858L T/H AIN8 DVDD 2.5V REFERENCE COMP REFIN /REF OUT DGND BUF CREF1 CHARGE REDISTRIBUTION DAC CLKIN CREF2 CAL SAR AND ADC CONTROL CALIBRATION MEMORY AND CONTROLLER CONVST BUSY SLEEP SERIAL INTERFACE/CONTROL REGISTER SYNC DIN DOUT SCLK PRODUCT HIGHLIGHTS 1. Specified for 3 V and 5 V supplies. 2. Automatic calibration on power-up. 3. Flexible power management options including automatic power-down after conversion. 4. Operates with reference voltages from 1.2 V to VDD. 5. Analog input range from 0 V to VDD. 6. Eight single-ended or four pseudo-differential input channels. 7. System and self-calibration. 8. Versatile serial I/O port (SPI/QSPI/8051/µP). 9. Lower power version AD7858L. *Patent pending. See page 31 for data sheet index. SPI and QSPI are trademarks of Motorola, Inc. REV. B Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 World Wide Web Site: http://www.analog.com Fax: 781/326-8703 © Analog Devices, Inc., 2000 1, 2 (AV = DV = +3.0 V to +5.5 V, REF /REF = 2.5 V External AD7858/AD7858L–SPECIFICATIONS Reference unless otherwise noted, f = 4 MHz (1.8 MHz B Grade (0ⴗC to +70ⴗC), 1 MHz A and B Grades (–40ⴗC to +85ⴗC) for L Version); f = DD DD IN OUT CLKIN SAMPLE 200 kHz (AD7858), 100 kHz (AD7858L); SLEEP = Logic High; TA = TMIN to TMAX, unless otherwise noted.) Specifications in ( ) apply to the AD7858L. Parameter DYNAMIC PERFORMANCE Signal to Noise + Distortion Ratio3 (SNR) Total Harmonic Distortion (THD) Peak Harmonic or Spurious Noise Intermodulation Distortion (IMD) Second Order Terms Third Order Terms Channel-to-Channel Isolation DC ACCURACY Resolution Integral Nonlinearity Differential Nonlinearity Total Unadjusted Error Unipolar Offset Error Unipolar Offset Error Match Positive Full-Scale Error Positive Full-Scale Error Match ANALOG INPUT Input Voltage Ranges Leakage Current Input Capacitance REFERENCE INPUT/OUTPUT REFIN Input Voltage Range Input Impedance REFOUT Output Voltage REFOUT Tempco LOGIC INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current, IIN Input Capacitance, CIN4 A Version1 B Version1 Units Test Conditions/Comments 70 71 dB min –78 –78 –78 –78 dB max dB max Typically SNR is 72 dB VIN = 10 kHz Sine Wave, fSAMPLE = 200 kHz (100 kHz) VIN = 10 kHz Sine Wave, fSAMPLE = 200 kHz (100 kHz) VIN = 10 kHz Sine Wave, fSAMPLE = 200 kHz (100 kHz) –78 –78 –90 –80 –80 –90 dB typ dB typ dB typ fa = 9.983 kHz, fb = 10.05 kHz, fSAMPLE = 200 kHz (100 kHz) fa = 9.983 kHz, fb = 10.05 kHz, fSAMPLE = 200 kHz (100 kHz) VIN = 25 kHz 12 ±1 ±1 12 ±1 ± 0.5 (± 1) Any Channel (± 1) ±1 ±1 Bits LSB max LSB max LSB max LSB max LSB max ±1 ±5 ± 2.5 (± 3) (± 1.5) 1.5 ±4 ± 1.5 1 ±1 ±5 ± 2.5 (± 3) (± 1.5) 1.5 ±4 ± 1.5 1 LSB typ LSB max LSB max LSB max LSB max LSB max LSB max LSB max LSB max 0 to VREF 0 to VREF Volts ±1 20 ±1 20 µA max pF typ 2.3/VDD 150 2.3/2.7 20 2.3/VDD 150 2.3/2.7 20 V min/max kΩ typ V min/max ppm/°C typ Functional from 1.2 V 2.4 2.1 0.8 0.6 ± 10 10 2.4 2.1 0.8 0.6 ± 10 10 V min V min V max V max µA max pF max AVDD = DVDD = 4.5 V to 5.5 V AVDD = DVDD = 3.0 V to 3.6 V AVDD = DVDD = 4.5 V to 5.5 V AVDD = DVDD = 3.0 V to 3.6 V Typically 10 nA, VIN = 0 V or VDD LOGIC OUTPUTS Output High Voltage, VOH Output Low Voltage, VOL Floating-State Leakage Current Floating-State Output Capacitance4 Output Coding CONVERSION RATE Conversion Time Track/Hold Acquisition Time 4 4 2.4 2.4 0.4 0.4 ± 10 ± 10 10 10 Straight (Natural) Binary V min V min V max µA max pF max 4.6 (18) µs max µs max µs min 0.4 (1) 4.6 (10) 0.4 (1) –2– 2.5 V External Reference VDD = 3 V, VDD = 5 V (B Grade Only) 5 V External Reference VDD = 5 V (L Version, 5 V External Reference, VDD = 5 V) (L Version) Guaranteed No Missed Codes to 12 Bits. 2.5 V External Reference VDD = 3 V, 5 V External Reference, VDD = 5 V Typically ± 2 LSBs 5 V External Reference, VDD = 5 V (L Version) (L Version, 5 V External Reference, VDD = 5 V) 5 V External Reference, VDD = 5 V i.e., AIN(+) – AIN(–) = 0 to VREF, AIN(–) can be biased up but AIN(+) cannot go below AIN(–) ISOURCE = 200 µA AVDD = DVDD = 4.5 V to 5.5 V AVDD = DVDD = 3.0 V to 3.6 V ISINK = 0.8 mA (L Versions Only, –40°C to +85°C, 1 MHz CLKIN) (L Versions Only, 0°C to +70°C, 1.8 MHz CLKIN) (L Versions Only) REV. B AD7858/AD7858L Parameter DYNAMIC PERFORMANCE AVDD, DVDD IDD Normal Mode5 Sleep Mode6 With External Clock On With External Clock Off Normal-Mode Power Dissipation Sleep Mode Power Dissipation With External Clock On With External Clock Off SYSTEM CALIBRATION Offset Calibration Span7 Gain Calibration Span7 A Version1 B Version1 Units +3.0/+5.5 +3.0/+5.5 V min/max 6 (1.9) 5.5 (1.9) 6 (1.9) 5.5 (1.9) mA max mA max AVDD = DVDD = 4.5 V to 5.5 V. Typically 4.5 mA (1.5) AVDD = DVDD = 3.0 V to 3.6 V. Typically 4.0 mA (1.5 mA) 10 10 µA typ 400 400 µA typ 5 5 µA max 200 200 µA typ 33 (10.5) 20 (6.85) 33 (10.5) 20 (6.85) mW max mW max Full Power-Down. Power Management Bits in Control Register Set as PMGT1 = 1, PMGT0 = 0 Partial Power-Down. Power Management Bits in Control Register Set as PMGT1 = 1, PMGT0 = 1 Typically 1 µA. Full Power-Down. Power Management Bits in Control Register Set as PMGT1 = 1, PMGT0 = 0 Partial Power-Down. Power Management Bits in Control Register Set as PMGT1 = 1, PMGT0 = 1 VDD = 5.5 V. Typically 25 mW (8); SLEEP = VDD VDD = 3.6 V. Typically 15 mW (5.4); SLEEP = VDD 55 36 27.5 18 55 36 27.5 18 µW typ µW typ µW max µW max VDD = 5.5 V. SLEEP = 0 V VDD = 3.6 V. SLEEP = 0 V VDD = 5.5 V. Typically 5.5 µW; SLEEP = 0 V VDD = 3.6 V. Typically 3.6 µW; SLEEP = 0 V V max/min V max/min Allowable Offset Voltage Span for Calibration Allowable Full-Scale Voltage Span for Calibration +0.05 × VREF/–0.05 × VREF +1.025 × VREF/–0.975 × VREF Test Conditions/Comments NOTES 1 Temperature ranges as follows: A, B Versions: –40°C to +85°C. For L Versions, A and B Versions f CLKIN = 1 MHz over –40°C to +85°C temperature range, B Version f CLKIN = 1.8 MHz over 0°C to +70°C temperature range. 2 Specifications apply after calibration. 3 SNR calculation includes distortion and noise components. 4 Sample tested @ +25°C to ensure compliance. 5 All digital inputs @ DGND except for CONVST, SLEEP, CAL, and SYNC @ DVDD. No load on the digital outputs. Analog inputs @ AGND. 6 CLKIN @ DGND when external clock off. All digital inputs @ DGND except for CONVST, SLEEP, CAL, and SYNC @ DVDD. No load on the digital outputs. Analog inputs @ AGND. 7 The Offset and Gain Calibration Spans are defined as the range of offset and gain errors that the AD7858/AD7858L can calibrate. Note also that these are voltage spans and are not absolute voltages ( i.e., the allowable system offset voltage presented at AIN(+) for the system offset error to be adjusted out will be AIN(–) ± 0.05 × VREF, and the allowable system full-scale voltage applied between AIN(+) and AIN(–) for the system full-scale voltage error to be adjusted out will be VREF ± 0.025 × VREF). This is explained in more detail in the Calibration section of the data sheet. Specifications subject to change without notice. REV. B –3– AD7858/AD7858L (AVDD = DVDD = +3.0 V to +5.5 V; fCLKIN = 4 MHz for AD7858 and 1.8/1 MHz for AD7858L; A MIN to TMAX , unless otherwise noted) TIMING SPECIFICATIONS1 T = T Limit at TMIN, TMAX (A, B Versions) 5V 3V Units Description 500 4 1.8 1 4 100 90 4.6 10 (18) –0.4 tSCLK ⫿0.4 tSCLK 90 90 115 60 30 0.4 tSCLK 0.4 tSCLK 50 50/0.4 tSCLK 50 130 90 2.5 tCLKIN 2.5 tCLKIN 31.25 kHz min MHz max MHz max MHz max MHz max ns min ns max µs max µs max ns min ns min/max ns max ns max ns max ns min ns min ns min ns min ns min ns min/max ns max ns max ns max ns max ns max ms typ Master Clock Frequency t125 t13 t146 t15 t16 tCAL7 500 4 1.8 1 4 100 50 4.6 10 (18) –0.4 tSCLK ⫿0.4 tSCLK 50 50 75 40 20 0.4 tSCLK 0.4 tSCLK 30 30/0.4 tSCLK 50 90 50 2.5 tCLKIN 2.5 tCLKIN 31.25 tCAL17 27.78 27.78 ms typ tCAL27 3.47 3.47 ms typ Parameter fCLKIN 2 fSCLK t1 3 t2 tCONVERT t3 t4 4 t5 4 t6 4 t7 t8 t9 t10 t11 L Version, 0°C to +70°C, B Grade Only L Version, –40°C to +85°C CONVST Pulsewidth CONVST↓ to BUSY↑ Propagation Delay Conversion Time = 18 tCLKIN L Version 1.8 (1) MHz CLKIN. Conversion Time = 18 tCLKIN SYNC↓ to SCLK↓ Setup Time (Noncontinuous SCLK Input) SYNC↓ to SCLK↓ Setup Time (Continuous SCLK Input) Delay from SYNC↓ Until DOUT Three-State Disabled Delay from SYNC↓ Until DIN Three-State Disabled Data Access Time After SCLK↓ Data Setup Time Prior to SCLK↑ Data Valid to SCLK Hold Time SCLK High Pulsewidth SCLK Low Pulsewidth SCLK↑ to SYNC↑ Hold Time (Noncontinuous SCLK) (Continuous SCLK) Delay from SYNC↑ Until DOUT Three-State Enabled Delay from SCLK↑ to DIN Being Configured as Output Delay from SCLK↑ to DIN Being Configured as Input CAL↑ to BUSY↑ Delay CONVST↓ to BUSY↑ Delay in Calibration Sequence Full Self-Calibration Time, Master Clock Dependent (125013 tCLKIN) Internal DAC Plus System Full-Scale Calibration Time, Master Clock Dependent (111114 tCLKIN) System Offset Calibration Time, Master Clock Dependent (13899 tCLKIN) NOTES 1 Sample tested at +25°C to ensure compliance. All input signals are specified with tr = tf = 5 ns (10% to 90% of V DD) and timed from a voltage level of 1.6 V. See Table XI and timing diagrams for different interface modes and Calibration. 2 Mark/Space ratio for the master clock input is 40/60 to 60/40. 3 The CONVST pulsewidth will apply here only for normal operation. When the part is in power-down mode, a different CONVST pulsewidth will apply (see Power-Down section). 4 Measured with the load circuit of Figure 1 and defined as the time required for the output to cross 0.8 V or 2.4 V. 5 t12 is derived form the measured time taken by the data outputs to change 0.5 V when loaded with the circuit of Figure 1. The measured number is then extrapolated back to remove the effects of charging or discharging the 100 pF capacitor. This means that the time, t 12, quoted in the timing characteristics is the true bus relinquish time of the part and is independent of the bus loading. 6 t14 is derived form the measured time taken by the data outputs to change 0.5 V when loaded with the circuit of Figure 1. The measured number is then extrapolated back to remove the effects of charging or discharging the 100 pF capacitor. This means that the time quoted in the Timing Characteristics is the true delay of the part in turning off the output drivers and configuring the DIN line as an input. Once this time has elapsed the user can drive the DIN line knowing that a bus conflict will not occur. 7 The typical time specified for the calibration times is for a master clock of 4 MHz. For the L version the calibration times will be longer than those quoted here due to the 1.8/1 MHz master clock. Specifications subject to change without notice. –4– REV. B AD7858/AD7858L TYPICAL TIMING DIAGRAMS Figures 2 and 3 show typical read and write timing diagrams for serial Interface Mode 2. The reading and writing occurs after conversion in Figure 2, and during conversion in Figure 3. To attain the maximum sample rate of 100 kHz (AD7858L) or 200 kHz (AD7858), reading and writing must be performed during conversion as in Figure 3. At least 400 ns acquisition time must be allowed (the time from the falling edge of BUSY to the next rising edge of CONVST) before the next conversion begins to ensure that the part is settled to the 12-bit level. If the user does not want to provide the CONVST signal, the conversion can be initiated in software by writing to the control register. 1.6mA TO OUTPUT PIN IOL +2.1V CL 100pF 200A IOH Figure 1. Load Circuit for Digital Output Timing Specifications tCONVERT = 4.6s MAX, 10s MAX FOR L VERSION t1 = 100ns MIN, t4 = 50/90ns MAX 5V/3V, t7 = 40/60ns MIN 5V/3V t1 CONVST (I/P) tCONVERT t2 BUSY (O/P) SYNC (I/P) t3 5 t4 t6 THREE-STATE DOUT (O/P) 6 t6 DB15 16 t10 t12 DB11 DB0 THREESTATE t8 t7 DIN (I/P) t11 t9 1 SCLK (I/P) DB15 DB11 DB0 Figure 2. AD7858/AD7858L Timing Diagram for Interface Mode 2 (Reading/Writing After Conversion) tCONVERT = 4.6s MAX, 10s MAX FOR L VERSION t1 = 100ns MIN, t4 = 50/90ns MAX 5V/3V, t7 = 40/60ns MIN 5V/3V t1 CONVST (I/P) tCONVERT t2 BUSY (O/P) SYNC (I/P) t3 5 t4 DOUT (O/P) THREE-STATE 6 t6 t6 DB15 DB11 16 t10 t12 DB0 THREESTATE t8 t7 DIN (I/P) t11 t9 1 SCLK (I/P) DB15 DB11 DB0 Figure 3. AD7858/AD7858L Timing Diagram for Interface Mode 2 (Reading/Writing During Conversion) REV. B –5– AD7858/AD7858L ABSOLUTE MAXIMUM RATINGS 1 SOIC, SSOP Package, Power Dissipation . . . . . . . . . . 450 mW θJA Thermal Impedance . . . 75°C/W (SOIC) 115°C/W (SSOP) θJC Thermal Impedance . . . . 25°C/W (SOIC) 35°C/W (SSOP) Lead Temperature, Soldering Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . +215°C Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . +220°C (TA = +25°C unless otherwise noted) AVDD to AGND . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V DVDD to DGND . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V AVDD to DVDD . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +0.3 V Analog Input Voltage to AGND . . . . –0.3 V to AVDD + 0.3 V Digital Input Voltage to DGND . . . . –0.3 V to DVDD + 0.3 V Digital Output Voltage to DGND . . . –0.3 V to DVDD + 0.3 V REFIN/REFOUT to AGND . . . . . . . . . –0.3 V to AVDD + 0.3 V Input Current to Any Pin Except Supplies2 . . . . . . . ± 10 mA Operating Temperature Range Commercial (A, B Versions) . . . . . . . . . . . –40°C to +85°C Storage Temperature Range . . . . . . . . . . . –65°C to +150°C Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . +150°C Plastic DIP Package, Power Dissipation . . . . . . . . . . 450 mW θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . . . 105°C/W θJC Thermal Impedance . . . . . . . . . . . . . . . . . . . . 34.7°C/W Lead Temperature, (Soldering, 10 sec) . . . . . . . . . . +260°C NOTES 1 Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2 Transient currents of up to 100 mA will not cause SCR latch-up. CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD7858/AD7858L features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. AD7858AN AD7858BN AD7858LAN3 AD7858LBN3 AD7858AR AD7858BR AD7858LAR3 AD7858LBR3 AD7858LARS3 EVAL-AD7858CB4 EVAL-CONTROL BOARD5 Linearity Power Error Dissipation Package (LSB)1 (mW) Options2 ±1 ± 1/2 ±1 ±1 ±1 ± 1/2 ±1 ±1 ±1 20 20 6.85 6.85 20 20 6.85 6.85 6.85 ESD SENSITIVE DEVICE PIN CONFIGURATIONS DIP, SOIC, AND SSOP ORDERING GUIDE Model WARNING! N-24 N-24 N-24 N-24 R-24 R-24 R-24 R-24 RS-24 CONVST 1 24 SYNC BUSY 2 23 SCLK SLEEP 3 22 CLKIN REFIN /REFOUT 4 AVDD 5 21 DIN AD7858/ AD7858L 20 DOUT AGND 6 TOP VIEW 19 DGND CREF1 7 (Not to Scale) 18 DVDD CREF2 8 17 CAL AIN1 9 16 AIN8 AIN2 10 15 AIN7 AIN3 11 14 AIN6 AIN4 12 13 AIN5 NOTES 1 Linearity error here refers to integral linearity error. 2 N = Plastic DIP; R = SOIC; RS = SSOP. 3 L signifies the low-power version. 4 This can be used as a stand-alone evaluation board or in conjunction with the EVALCONTROL BOARD for evaluation/demonstration purposes. 5 This board is a complete unit allowing a PC to control and communicate with all Analog Devices evaluation boards ending in the CB designators. –6– REV. B AD7858/AD7858L PIN FUNCTION DESCRIPTIONS Pin Mnemonic Description 1 CONVST 2 BUSY 3 SLEEP 4 REFIN/REFOUT 5 6 7 AVDD AGND CREF1 8 CREF2 Convert Start. Logic Input. A low to high transition on this input puts the track/hold into its hold mode and starts conversion. When this input is not used, it should be tied to DVDD. Busy Output. The busy output is triggered high by the falling edge of CONVST or rising edge of CAL, and remains high until conversion is completed. BUSY is also used to indicate when the AD7858/ AD7858L has completed its on-chip calibration sequence. Sleep Input/Low-Power Mode. A Logic 0 initiates a sleep, and all circuitry is powered down including the internal voltage reference provided there is no conversion or calibration being performed. Calibration data is retained. A Logic 1 results in normal operation. See Power-Down section for more details. Reference Input/Output. This pin is connected to the internal reference through a series resistor and is the reference source for the analog-to-digital converter. The nominal reference voltage is 2.5 V and this appears at the pin. This pin can be overdriven by an external reference or can be taken as high as AVDD. When this pin is tied to AVDD, or when an externally applied reference approaches AVDD, the CREF1 pin should also be tied to AVDD. Analog Positive Supply Voltage, +3.0 V to +5.5 V. Analog Ground. Ground reference for track/hold, reference, and DAC. Reference Capacitor (0.1 µF Multilayer Ceramic). This external capacitor is used as a charge source for the internal DAC. The capacitor should be tied between the pin and AGND. Reference Capacitor (0.01 µF Ceramic Disc). This external capacitor is used in conjunction with the onchip reference. The capacitor should be tied between the pin and AGND. Analog Inputs. Eight analog inputs that can be used as eight single-ended inputs (referenced to AGND) or four pseudo-differential inputs. Channel configuration is selected by writing to the control register. Both the positive and negative inputs cannot go below AGND or above AVDD at any time. Also the positive input cannot go below the negative input. See Table III for channel selection. Calibration Input. This pin has an internal pull-up current source of 0.15 µA. A Logic 0 on this pin resets all calibration control logic and initiates a calibration on its rising edge. There is the option of connecting a 10 nF capacitor from this pin to DGND to allow for an automatic self-calibration on power-up. This input overrides all other internal operations. If the autocalibration is not required, this pin should be tied to a logic high. Digital Supply Voltage, +3.0 V to +5.5 V. Digital Ground. Ground reference point for digital circuitry. Serial Data Output. The data output is supplied to this pin as a 16-bit serial word. Serial Data Input. The data to be written is applied to this pin in serial form (16-bit word). This pin can act as an input pin or as a I/O pin depending on the serial interface mode the part is in (see Table X). Master clock signal for the device (4 MHz AD7858, 1.8 MHz AD7858L). Sets the conversion and calibration times. Serial Port Clock. Logic Input. The user must provide a serial clock on this input. Frame Sync. Logic Input. This pin is level triggered active low and frames the serial clock for the read and write operations (see Table IX). 9–16 AIN1–AIN8 17 CAL 18 19 20 21 DVDD DGND DOUT DIN 22 CLKIN 23 24 SCLK SYNC REV. B –7– AD7858/AD7858L TERMINOLOGY1 Integral Nonlinearity Total Harmonic Distortion Total harmonic distortion (THD) is the ratio of the rms sum of harmonics to the fundamental. For the AD7858/AD7858L, it is defined as: This is the maximum deviation from a straight line passing through the endpoints of the ADC transfer function. The endpoints of the transfer function are zero scale, a point 1/2 LSB below the first code transition, and full scale, a point 1/2 LSB above the last code transition. THD ( dB ) = 20 log Differential Nonlinearity 2 2 2 2 2 (V2 + V3 + V4 + V5 + V6 ) V1 This is the difference between the measured and the ideal 1 LSB change between any two adjacent codes in the ADC. where V1 is the rms amplitude of the fundamental and V2, V3, V4, V5, and V6 are the rms amplitudes of the second through the sixth harmonics. Total Unadjusted Error Peak Harmonic or Spurious Noise This is the deviation of the actual code from the ideal code taking all errors into account (Gain, Offset, Integral Nonlinearity, and other errors) at any point along the transfer function. Unipolar Offset Error This is the deviation of the first code transition (00 . . . 000 to 00 . . . 001) from the ideal AIN(+) voltage (AIN(–) + 1/2 LSB). Positive Full-Scale Error This is the deviation of the last code transition from the ideal AIN(+) voltage (AIN(–) + Full Scale – 1.5 LSB) after the offset error has been adjusted out. Peak harmonic or spurious noise is defined as the ratio of the rms value of the next largest component in the ADC output spectrum (up to fS/2 and excluding dc) to the rms value of the fundamental. Normally, the value of this specification is determined by the largest harmonic in the spectrum, but for parts where the harmonics are buried in the noise floor, it will be a noise peak. Intermodulation Distortion With inputs consisting of sine waves at two frequencies, fa and fb, any active device with nonlinearities will create distortion products at sum and difference frequencies of mfa ± nfb where m, n = 0, 1, 2, 3, etc. Intermodulation distortion terms are those for which neither m nor n are equal to zero. For example, the second order terms include (fa + fb) and (fa – fb), while the third order terms include (2fa + fb), (2fa – fb), (fa + 2fb), and (fa – 2fb). Channel-to-Channel Isolation Channel-to-channel isolation is a measure of crosstalk between the channels. It is measured by applying a full-scale 25 kHz signal to the other seven channels and determining how much that signal is attenuated in the channel of interest. The figure given is the worst case for all channels. Track/Hold Acquisition Time The track/hold amplifier returns into track mode and the end of conversion. Track/hold acquisition time is the time required for the output of the track/hold amplifier to reach its final value, within ± 1/2 LSB, after the end of conversion. Signal to (Noise + Distortion) Ratio This is the measured ratio of signal to (noise + distortion) at the output of the A/D converter. The signal is the rms amplitude of the fundamental. Noise is the sum of all nonfundamental signals up to half the sampling frequency (fS/2), excluding dc. The ratio is dependent on the number of quantization levels in the digitization process; the more levels, the smaller the quantization noise. The theoretical signal to (noise + distortion) ratio for an ideal N-bit converter with a sine wave input is given by: Testing is performed using the CCIF standard where two input frequencies near the top end of the input bandwidth are used. In this case, the second order terms are usually distanced in frequency from the original sine waves, while the third order terms are usually at a frequency close to the input frequencies. As a result, the second and third order terms are specified separately. The calculation of the intermodulation distortion is as per the THD specification where it is the ratio of the rms sum of the individual distortion products to the rms amplitude of the sum of the fundamentals expressed in dBs. Signal to (Noise + Distortion) = (6.02 N +1.76) dB Thus for a 12-bit converter, this is 74 dB. 1 AIN(+) refers to the positive input of the pseudo differential pair, and AIN(–) refers to the negative analog input of the pseudo differential pair or to AGND depending on the channel configuration. –8– REV. B AD7858/AD7858L ON-CHIP REGISTERS The AD7858/AD7858L powers up with a set of default conditions. The only writing required is to select the channel configuration. Without performing any other write operations the AD7858/AD7858L still retains the flexibility for performing a full power-down and a full self-calibration. Extra features and flexibility, such as performing different power-down options, different types of calibrations including system calibration, and software conversion start, can be selected by further writing to the part. The AD7858/AD7858L contains a Control Register, ADC Output Data Register, Status Register, Test Register, and 10 Calibration Registers. The control register is write-only, the ADC output data register and the status register are read-only, and the test and calibration registers are both read/write registers. The Test Register is used for testing the part and should not be written to. Addressing the On-Chip Registers Writing A write operation to the AD7858/AD7858L consists of 16 bits. The two MSBs, ADDR0 and ADDR1, are decoded to determine which register is addressed, and the subsequent 14 bits of data are written to the addressed register. It is not until all 16 bits are written that the data is latched into the addressed registers. Table I shows the decoding of the address bits while Figure 4 shows the overall write register hierarchy. Table I. Write Register Addressing ADDR1 ADDR0 Comment 0 0 0 1 1 0 1 1 This combination does not address any register so the subsequent 14 data bits are ignored. This combination addresses the TEST REGISTER. The subsequent 14 data bits are written to the test register. This combination addresses the CALIBRATION REGISTERS. The subsequent 14 data bits are written to the selected calibration register. This combination addresses the CONTROL REGISTER. The subsequent 14 data bits are written to the control register. Reading To read from the various registers the user must first write to Bits 6 and 7 in the Control Register, RDSLT0 and RDSLT1. These bits are decoded to determine which register is addressed during a read operation. Table II shows the decoding of the read address bits while Figure 5 shows the overall read register hierarchy. The power-up status of these bits is 00 so that the default read will be from the ADC output data register. Once the read selection bits are set in the Control Register, all subsequent read operations that follow will be from the selected register until the read selection bits are changed in the Control Register. Table II. Read Register Addressing RDSLT1 RDSLT0 Comment 0 0 0 1 1 1 0 1 All successive read operations will be from ADC OUTPUT DATA REGISTER. This is the power-up default setting. There will always be 4 leading zeros when reading from the ADC Output Data Register. All successive read operations will be from TEST REGISTER. All successive read operations will be from CALIBRATION REGISTERS. All successive read operations will be from STATUS REGISTER. RDSLT1, RDSLT0 DECODE ADDR1, ADDR0 DECODE 01 10 TEST REGISTER CALSLT1, CALSLT0 DECODE GAIN(1) OFFSET(1) DAC(8) GAIN(1) OFFSET(1) 00 01 00 11 CALIBRATION REGISTERS OFFSET(1) 10 ADC OUTPUT DATA REGISTER CONTROL REGISTER 10 TEST REGISTER GAIN(1) OFFSET(1) DAC(8) GAIN(1) 11 CALSLT1, CALSLT0 DECODE Figure 4. Write Register Hierarchy/Address Decoding REV. B 01 00 11 CALIBRATION REGISTERS GAIN(1) OFFSET(1) 01 OFFSET(1) 10 STATUS REGISTER GAIN(1) 11 Figure 5. Read Register Hierarchy/Address Decoding –9– AD7858/AD7858L CONTROL REGISTER The arrangement of the Control Register is shown below. The control register is a write only register and contains 14 bits of data. The control register is selected by putting two 1s in ADDR1 and ADDR0. The function of the bits in the control register are described below. The power-up status of all bits is 0. MSB SGL/DIFF RDSLT0 CH2 CH1 CH0 PMGT1 PMGT0 RDSLT1 2/3 MODE CONVST CALMD CALSLT1 CALSLT0 STCAL LSB CONTROL REGISTER BIT FUNCTION DESCRIPTION Bit Mnemonic Comment 13 SGL/DIFF 12 11 10 9 8 7 6 5 CH2 CH1 CH0 PMGT1 PMGT0 RDSLT1 RDSLT0 2/3 MODE A 0 in this bit position configures the input channels in pseudo-differential mode. A 1 in this bit position configures the input channels in single-ended mode (see Table III). These three bits are used to select the channel on which the conversion is performed. The channels can be configured as eight single-ended channels or four pseudo-differential channels. The default selection is AIN1 for the positive input and AIN2 for the negative input (see Table III for channel selection). Power Management Bits. These two bits are used with the SLEEP pin for putting the part into various Power-Down Modes (see Power-Down section for more details). Theses two bits determine which register is addressed for the read operations (see Table II). 4 CONVST 3 2 1 0 CALMD CALSLT1 CALSLT0 STCAL Interface Mode Select Bit. With this bit set to 0, Interface Mode 2 is enabled. With this bit set to 1, Interface Mode 1 is enabled where DIN is used as an output as well as an input. This bit is set to 0 by default after every read cycle; thus when using the Two-Wire Interface Mode, this bit needs to be set to 1 in every write cycle. Conversion Start Bit. A logic one in this bit position starts a single conversion, and this bit is automatically reset to 0 at the end of conversion. This bit may also be used in conjunction with system calibration (see Calibration section.) Calibration Mode Bit. A 0 here selects self-calibration, and a 1 selects a system calibration (see Table IV). Calibration Selection Bits and Start Calibration Bit. These bits have two functions. With the STCAL bit set to 1 the CALSLT1 and CALSLT0 bits determine the type of calibration per formed by the part (see Table IV). The STCAL bit is automatically reset to 0 at the end of calibration. With the STCAL bit set to 0 the CALSLT1 and CALSLT0 bits are decoded to address the calibration register for read/write of calibration coefficients (see section on the Calibration Registers for more details). –10– REV. B AD7858/AD7858L Table III. Channel Selection SGL/DIFF CH2 CH1 CH0 AIN(+)* AIN(–)* 0 0 0 0 0 0 0 0 0 0 1 1 0 1 0 1 AIN1 AIN3 AIN5 AIN7 AIN2 AIN4 AIN6 AIN8 0 0 0 0 1 1 1 1 0 0 1 1 0 1 0 1 AIN2 AIN4 AIN6 AIN8 AIN1 AIN3 AIN5 AIN7 1 1 1 1 0 0 0 0 0 0 1 1 0 1 0 1 AIN1 AIN3 AIN5 AIN7 AGND AGND AGND AGND 1 1 1 1 1 1 1 1 0 0 1 1 0 1 0 1 AIN2 AIN4 AIN6 AIN8 AGND AGND AGND AGND *AIN(+) refers to the positive input seen by the AD7858/AD7858L sample and hold circuit, *AIN(–) refers to the negative input seen by the AD7858/AD7858L sample and hold circuit. Table IV. Calibration Selection CALMD CALSLT1 CALSLT0 Calibration Type 0 0 0 A Full Internal Calibration is initiated where the Internal DAC is calibrated followed by the Internal Gain Error, and finally the Internal Offset Error is calibrated out. This is the default setting. 0 0 1 Here the Internal Gain Error is calibrated out followed by the Internal Offset Error calibrated out. 0 1 0 This calibrates out the Internal Offset Error only. 0 1 1 This calibrates out the Internal Gain Error only. 1 0 0 A Full System Calibration is initiated here where first the Internal DAC is calibrated followed by the System Gain Error, and finally the System Offset Error is calibrated out. 1 0 1 Here the System Gain Error is calibrated out followed by the System Offset Error. 1 1 0 This calibrates out the System Offset Error only. 1 1 1 This calibrates out the System Gain Error only. REV. B –11– AD7858/AD7858L STATUS REGISTER The arrangement of the Status Register is shown below. The status register is a read-only register and contains 16 bits of data. The status register is selected by first writing to the control register and putting two 1s in RDSLT1 and RDSLT0. The function of the bits in the status register are described below. The power-up status of all bits is 0. START WRITE TO CONTROL REGISTER SETTING RDSLT0 = RDSLT1 = 1 READ STATUS REGISTER Figure 6. Flowchart for Reading the Status Register MSB ZERO BUSY SGL/DIFF CH2 RDSLT1 RDSLT0 2/3 MODE X CH1 CALMD CH0 PMGT1 PMGT0 CALSLT1 CALSLT0 STCAL LSB STATUS REGISTER BIT FUNCTION DESCRIPTION Bit Mnemonic Comment 15 ZERO This bit is always 0. 14 BUSY Conversion/Calibration Busy Bit. When this bit is 1, it indicates that there is a conversion or calibration in progress. When this bit is 0, there is no conversion or calibration in progress. 13 12 11 10 SGL/DIFF CH2 CH1 CH0 These four bits indicate the channel selected for conversion (see Table III). 9 8 PMGT1 PMGT0 Power management bits. These bits along with the SLEEP pin will indicate if the part is in a power-down mode or not. See Table VI for description. 7 6 RDSLT1 RDSLT0 Both of these bits are always 1, indicating it is the status register being read (see Table II). 5 2/3 MODE Interface Mode Select Bit. With this bit at 0, the device is in Interface Mode 2. With this bit at 1, the device is in Interface Mode 1. This bit is reset to 0 after every read cycle. 4 X Don’t care bit. 3 CALMD Calibration Mode Bit. A 0 in this bit indicates a self-calibration is selected, and a 1 in this bit indicates a system calibration is selected (see Table IV). 2 1 0 CALSLT1 CALSLT0 STCAL Calibration Selection Bits and Start Calibration Bit. The STCAL bit is read as a 1 if a calibration is in progress and as a 0 if there is no calibration in progress. The CALSLT1 and CALSLT0 bits indicate which of the calibration registers are addressed for reading and writing (see section on the Calibration Registers for more details). –12– REV. B AD7858/AD7858L CALIBRATION REGISTERS The AD7858/AD7858L has 10 calibration registers in all, eight for the DAC, one for the offset, and one for gain. Data can be written to or read from all 10 calibration registers. In self- and system calibration the part automatically modifies the calibration registers; only if the user needs to modify the calibration registers should an attempt be made to read from and write to the calibration registers. Addressing the Calibration Registers The calibration selection bits in the control register CALSLT1 and CALSLT0 determine which of the calibration registers are addressed (see Table V). The addressing applies to both the read and write operations for the calibration registers. The user should not attempt to read from and write to the calibration registers at the same time. Table V. Calibration Register Addressing CALSLT1 CALSLT0 Comment 0 0 1 1 0 1 0 1 This combination addresses the Gain (1), Offset (1) and DAC Registers (8). Ten registers in total. This combination addresses the Gain (1) and Offset (1) Registers. Two registers in total. This combination addresses the Offset Register. One register in total. This combination addresses the Gain Register. One register in total. Writing to/Reading from the Calibration Registers For writing to the calibration registers a write to the control register is required to set the CALSLT0 and CALSLT1 bits. For reading from the calibration registers a write to the control register is required to set the CALSLT0 and CALSLT1 bits, but also to set the RDSLT1 and RDSLT0 bits to 10 (this addresses the calibration registers for reading). The calibration register pointer is reset on writing to the control register setting the CALSLT1 and CALSLT0 bits, or upon completion of all the calibration register write/read operations. When reset it points to the first calibration register in the selected write/read sequence. The calibration register pointer will point to the gain calibration register upon reset in all but one case, this case being where the offset calibration register is selected on its own (CALSLT1 = 1, CALSLT0 = 0). Where more than one calibration register is being accessed the calibration register pointer will be automatically incremented after each calibration register write/read operation. The order in which the 10 calibration registers are arranged is shown in Figure 7. The user may abort at any time before all the calibration register write/read operations are completed, and the next control register write operation will reset the calibration register pointer. The flow chart in Figure 8 shows the sequence for writing to the calibration registers and Figure 9 for reading. When reading from the calibration registers there will always be two leading zeros for each of the registers. When operating in Serial Interface Mode 1 the read operations to the calibration registers cannot be aborted. The full number of read operations must be completed (see section on Serial Interface Mode 1 Timing for more detail). CALIBRATION REGISTERS CAL REGISTER ADDRESS POINTER CALIBRATION REGISTER ADDRESS POINTER POSITION IS DETERMINED BY THE NUMBER OF CALIBRATION REGISTERS ADDRESSED AND THE NUMBER OF READ/WRITE OPERATIONS GAIN REGISTER (1) OFFSET REGISTER (2) DAC 1ST MSB REGISTER (3) . . . . . . . . . . . . . . CAL REGISTER POINTER IS AUTOMATICALLY RESET WRITE TO CAL REGISTER (ADDR1 = 1, ADDR0 = 0) CAL REGISTER POINTER IS AUTOMATICALLY INCREMENTED LAST REGISTER WRITE OPERATION OR ABORT ? NO FINISHED Figure 8. Flowchart for Writing to the Calibration Registers (10) Figure 7. Calibration Register Arrangements REV. B WRITE TO CONTROL REGISTER SETTING STCAL = 0 AND CALSLT1, CALSLT0 = 00, 01, 10, 11 YES . . . . . . . DAC 8TH MSB REGISTER START –13– AD7858/AD7858L Q. If a +20 mV offset is present in the analog input signal and the reference voltage is 2.5 V what code needs to be written to the offset register to compensate for the offset? START WRITE TO CONTROL REGISTER SETTING STCAL = 0, RDSLT1 = 1, RDSLT0 = 0, AND CALSLT1, CALSLT0 = 00, 01, 10, 11 A. 2.5 V reference implies that the resolution in the offset register is 5% × 2.5 V/213 = 0.015 mV. +20 mV/0.015 mV = 1310.72; rounding to the nearest number gives 1311. In binary terms this is 0101 0001 1111. Therefore, decrease the offset register by 0101 0001 1111. CAL REGISTER POINTER IS AUTOMATICALLY RESET This method of compensating for offset in the analog input signal allows for fine tuning the offset compensation. If the offset on the analog input signal is known, there will be no need to apply the offset voltage to the analog input pins and do a system calibration. The offset compensation can take place in software. READ CAL REGISTER CAL REGISTER POINTER IS AUTOMATICALLY INCREMENTED LAST REGISTER READ OPERATION OR ABORT ? Adjusting the Gain Calibration Register The gain calibration register contains 16 bits, two leading 0s and 14 data bits. The data bits are binary weighted as in the offset calibration register. The gain register value is effectively multiplied by the analog input to scale the conversion result over the full range. Increasing the gain register compensates for a smaller analog input range and decreasing the gain register compensates for a larger input range. The maximum analog input range that the gain register can compensate for is 1.025 times the reference voltage, and the minimum input range is 0.975 times the reference voltage. NO YES FINISHED Figure 9. Flowchart for Reading from the Calibration Registers Adjusting the Offset Calibration Register The offset calibration register contains 16 bits, two leading zeros, and 14 data bits. By changing the contents of the offset register different amounts of offset on the analog input signal can be compensated for. Increasing the number in the offset calibration register compensates for negative offset on the analog input signal, and decreasing the number in the offset calibration register compensates for positive offset on the analog input signal. The default value of the offset calibration register is 0010 0000 0000 0000 approximately. This is not an exact value, but the value in the offset register should be close to this value. Each of the 14 data bits in the offset register is binary weighted; the MSB has a weighting of 5% of the reference voltage, the MSB-1 has a weighting of 2.5%, the MSB-2 has a weighting of 1.25%, and so on down to the LSB which has a weighting of 0.0006%. This gives a resolution of ± 0.0006% of VREF approximately. More accurately the resolution is ± (0.05 × VREF )/213 volts = ± 0.015 mV, with a 2.5 V reference. The maximum offset that can be compensated for is ± 5% of the reference voltage, which equates to ± 125 mV with a 2.5 V reference and ± 250 mV with a 5 V reference. –14– REV. B AD7858/AD7858L CIRCUIT INFORMATION The AD7858/AD7858L is a fast, 12-bit single supply A/D converter. The part requires an external 4 MHz/1.8 MHz master clock (CLKIN), two CREF capacitors, a CONVST signal to start conversion, and power supply decoupling capacitors. The part provides the user with track/hold, on-chip reference, calibration features, A/D converter, and serial interface logic functions on a single chip. The A/D converter section of the AD7858/AD7858L consists of a conventional successive-approximation converter based around a capacitor DAC. The AD7858/AD7858L accepts an analog input range of 0 to +VDD where the reference can be tied to VDD. The reference input to the part is buffered on-chip. A major advantage of the AD7858/AD7858L is that a conversion can be initiated in software as well as applying a signal to the CONVST pin. Another innovative feature of the AD7858/ AD7858L is self-calibration on power-up, which is initiated having a capacitor from the CAL pin to AGND, to give superior dc accuracy. See Automatic Calibration on Power-Up section. The part is available in a 24-pin SSOP package and this offers the user considerable space-saving advantages over alternative solutions. The AD7858L version typically consumes only 5.5 mW making it ideal for battery-powered applications. CONVERTER DETAILS The master clock for the part must be applied to the CLKIN pin. Conversion is initiated on the AD7858/AD7858L by pulsing the CONVST input or by writing to the control register and setting the CONVST bit to 1. On the rising edge of CONVST (or at the end of the control register write operation), the onchip track/hold goes from track to hold mode. The falling edge of the CLKIN signal that follows the rising edge of the CONVST signal initiates the conversion, provided the rising edge of CONVST occurs at least 10 ns typically before this CLKIN edge. The conversion cycle will take 16.5 CLKIN periods from this CLKIN falling edge. If the 10 ns setup time is not met, the conversion will take 17.5 CLKIN periods. The maximum specified conversion time is 4.6 µs for the AD7858 (18tCLKIN, CLKIN = 4 MHz) and 10 µs for the AD7858L (18tCLKIN, CLKIN = 1.8 MHz). When a conversion is completed, the BUSY output goes low, and then the result of the conversion can be read by accessing the data through the serial interface. To obtain optimum performance from the part, the read operation should not occur during the conversion or 400 ns prior to the next CONVST rising edge. However, the maximum throughput rates are achieved by reading/writing during conversion, and reading/writing during conversion is likely to degrade the Signal to (Noise + Distortion) by only 0.5 dBs. The AD7858 can operate at throughput rates up to 200 kHz, 100 kHz for the AD7858L. For the AD7858 a conversion takes 18 CLKIN periods; 2 CLKIN periods are needed for the acquisition time giving a full cycle time of 5 µs (= 200 kHz, CLKIN = 4 MHz). For the AD7858L 100 kHz throughput can be obtained as follows: the CLKIN and CONVST signals are arranged to give a conversion time of 16.5 CLKIN periods as described above, 1.5 CLKIN periods are allowed for the acquisition time. This gives a full cycle time of 10 µs (=100 kHz, CLKIN = 1.8 MHz). When using the software conversion start for maximum throughput the user must ensure the control register write operation extends beyond the falling edge of BUSY. The falling edge of BUSY resets the CONVST bit to 0 and allows it to be reprogrammed to 1 to start the next conversion. TYPICAL CONNECTION DIAGRAM Figure 10 shows a typical connection diagram for the AD7858/ AD7858L. The AGND and the DGND pins are connected together at the device for good noise suppression. The CAL pin has a 0.01 µF capacitor to enable an automatic self-calibration on power-up. The conversion result is output in a 16-bit word with four leading zeros followed by the MSB of the 12-bit result. Note that after the AVDD and DVDD power-up the part will 4MHz/1.8MHz OSCILLATOR 200kHz/100kHz PULSE GENERATOR ANALOG SUPPLY +3V TO +5V 10F MASTER CLOCK INPUT 0.1F 0.1F CONVERSION START INPUT AVDD DVDD 0V TO 2.5V INPUT 0.1F 0.01F DVDD 0.01F AIN(–) SCLK CREF1 CREF2 OSCILLOSCOPE CLKIN AIN(+) CH1 SERIAL CLOCK INPUT CONVST AD7858/ AD7858L SLEEP CH2 SYNC CH3 FRAME SYNC INPUT DIN CH5 DOUT AGND AUTO CAL ON POWER-UP CH4 SERIAL DATA INPUT CAL SERIAL DATA OUTPUT DGND 0.1F INTERNAL/ EXTERNAL REFERENCE OPTIONAL AD780/ EXTERNAL REF-192 REFERENCE DATA GENERATOR PULSE GENERATOR Figure 10. Typical Circuit REV. B –15– 4 LEADING ZEROS FOR ADC DATA AD7858/AD7858L For applications where power consumption is a major concern then the SLEEP pin can be connected to DGND. See PowerDown section for more detail on low power applications. ANALOG INPUT The equivalent circuit of the analog input section is shown in Figure 11. During the acquisition interval the switches are both in the track position and the AIN(+) charges the 20 pF capacitor through the 125 Ω resistance. On the rising edge of CONVST switches SW1 and SW2 go into the hold position retaining charge on the 20 pF capacitor as a sample of the signal on AIN(+). The AIN(–) is connected to the 20 pF capacitor, and this unbalances the voltage at node A at the input of the comparator. The capacitor DAC adjusts during the remainder of the conversion cycle to restore the voltage at node A to the correct value. This action transfers a charge, representing the analog input signal, to the capacitor DAC which in turn forms a digital representation of the analog input signal. The voltage on the AIN(–) pin directly influences the charge transferred to the capacitor DAC at the hold instant. If this voltage changes during the conversion period, the DAC representation of the analog input voltage will be altered. Therefore it is most important that the voltage on the AIN(–) pin remains constant during the conversion period. Furthermore it is recommended that the AIN(–) pin is always connected to AGND or to a fixed dc voltage. For ac applications, removing high frequency components from the analog input signal is recommended by use of an RC lowpass filter on the AIN(+) pin as shown in Figure 13. In applications where harmonic distortion and signal to noise ratio are critical the analog input should be driven from a low impedance source. Large source impedances will significantly affect the ac performance of the ADC. This may necessitate the use of an input buffer amplifier. The choice of the op amp will be a function of the particular application. When no amplifier is used to drive the analog input the source impedance should be limited to low values. The maximum source impedance will depend on the amount of total harmonic distortion (THD) that can be tolerated. The THD will increase as the source impedance increases and performance will degrade. Figure 12 shows a graph of the total harmonic distortion versus analog input signal frequency for different source impedances. With the setup as in Figure 13, the THD is at the –90 dB level. With a source impedance of 1 kΩ and no capacitor on the AIN(+) pin, the THD increases with frequency. –72 THD vs. FREQUENCY FOR DIFFERENT SOURCE IMPEDANCES –76 RIN = 1k⍀ THD – dB require approximately 150 ms for the internal reference to settle and for the automatic calibration on power-up to be completed. Acquisition Time The track and hold amplifier enters its tracking mode on the falling edge of the BUSY signal. The time required for the track and hold amplifier to acquire an input signal will depend on how quickly the 20 pF input capacitance is charged. The acquisition time is calculated using the formula: –80 –84 RIN = 50⍀, 10nF AS IN FIGURE 13 –88 –92 0 tACQ = 9 × (RIN + 125 Ω) × 20 pF where RIN is the source impedance of the input signal, and 125 Ω, 20 pF is the input R, C. 125⍀ TRACK AIN(+) AIN(–) 125⍀ SW1 HOLD CAPACITOR DAC 20pF NODE A SW2 TRACK HOLD COMPARATOR CREF2 Figure 11. Analog Input Equivalent Circuit DC/AC Applications 20 40 60 INPUT FREQUENCY – kHz 80 100 Figure 12. THD vs. Analog Input Frequency In a single supply application (both 3 V and 5 V), the V+ and V– of the op amp can be taken directly from the supplies to the AD7858/AD7858L which eliminates the need for extra external power supplies. When operating with rail-to-rail inputs and outputs, at frequencies greater than 10 kHz care must be taken in selecting the particular op amp for the application. In particular for single supply applications the input amplifiers should be connected in a gain of –1 arrangement to get the optimum performance. Figure 13 shows the arrangement for a single supply application with a 50 Ω and 10 nF low-pass filter (cutoff frequency 320 kHz) on the AIN(+) pin. Note that the 10 nF is a capacitor with good linearity to ensure good ac performance. Recommended single supply op amps are the AD820 and the AD820-3 V. For dc applications high source impedances are acceptable provided there is enough acquisition time between conversions to charge the 20 pF capacitor. The acquisition time can be calculated from the above formula for different source impedances. For example with RIN = 5 kΩ, the required acquisition time will be 922 ns. +3V TO +5V 10k⍀ VIN (0 TO VREF) 10k⍀ V+ 10F 0.1F 50⍀ 10k⍀ VREF 10k⍀ V+ AD820 AD820-3V 10nF (NPO) TO AIN(+) OF AD7858/AD7858L Figure 13. Analog Input Buffering –16– REV. B AD7858/AD7858L Input Range REFERENCE SECTION The analog input range for the AD7858/AD7858L is 0 V to VREF. The AIN(–) pin on the AD7858/AD7858L can be biased up above AGND, if required. The advantage of biasing the lower end of the analog input range away from AGND is that the user does not need to have the analog input swing all the way down to AGND. This has the advantage in true singlesupply applications that the input amplifier does not need to swing all the way down to AGND. The upper end of the analog input range is shifted up by the same amount. Care must be taken so that the bias applied does not shift the upper end of the analog input above the AVDD supply. In the case where the reference is the supply, AVDD, the AIN(–) must be tied to AGND. For specified performance, it is recommended that when using an external reference this reference should be between 2.3 V and the analog supply AVDD. The connections for the relevant reference pins are shown in the typical connection diagrams. If the internal reference is being used, the REFIN/REFOUT pin should have a 100 nF capacitor connected to AGND very close to the REFIN/REFOUT pin. These connections are shown in Figure 16. AIN(+) VIN = 0 TO VREF TRACK AND HOLD AMPLIFIER DOUT AIN(–) If the internal reference is required for use external to the ADC, it should be buffered at the REFIN/REFOUT pin and a 100 nF connected from this pin to AGND. The typical noise performance for the internal reference, with 5 V supplies, is 150 nV/√Hz @ 1 kHz and dc noise is 100 µV p-p. ANALOG SUPPLY +3V TO +5V STRAIGHT BINARY FORMAT 10F 0.1F 0.1F AVDD DVDD CREF1 AD7858/ AD7858L 0.1F CREF2 Figure 14. 0 to VREF Input Configuration AD7858/ AD7858L 0.01F Transfer Function For the AD7858/AD7858L input range the designed code transitions occur midway between successive integer LSB values (i.e., 1/2 LSB, 3/2 LSBs, 5/2 LSBs . . . FS – 3/2 LSBs). The output coding is straight binary with 1 LSB = FS/4096 = 3.3 V/ 4096 = 0.8 mV when VREF = 3.3 V. The ideal input/output transfer characteristic is shown in Figure 15. OUTPUT CODE 111...111 111...110 111...101 111...100 000...011 1LSB = FS 4096 000...010 REFIN/REFOUT 0.1F Figure 16. Relevant Connections When Using Internal Reference The other option is that the REFIN/REFOUT pin be overdriven by connecting it to an external reference. This is possible due to the series resistance from the REFIN/REFOUT pin to the internal reference. This external reference can have a range that includes AVDD. When using AVDD as the reference source, the 100 nF capacitor from the REFIN/REFOUT pin to AGND should be as close as possible to the REFIN/REFOUT pin, and also the CREF1 pin should be connected to AVDD to keep this pin at the same level as the reference. The connections for this arrangement are shown in Figure 17. When using AVDD it may be necessary to add a resistor in series with the AVDD supply. This will have the effect of filtering the noise associated with the AVDD supply. 000...001 ANALOG SUPPLY +3V TO +5V 000...000 0V 1LSB 10F 0.1F 0.1F +FS –1LSB VIN = (AIN(+) – AIN(–)), INPUT VOLTAGE AVDD Figure 15. AD7858/AD7858L Transfer Characteristic DVDD CREF1 0.1F CREF2 AD7858/ AD7858L 0.01F REFIN/REFOUT 0.1F Figure 17. Relevant Connections When Using AVDD as the Reference REV. B –17– AD7858/AD7858L PERFORMANCE CURVES –78 AVDD = DVDD = 3.3V/5.0V, Figure 18 shows a typical FFT plot for the AD7858 at 200 kHz sample rate and 10 kHz input frequency. 100mVp-p SINE WAVE ON AVDD –80 0 –82 –20 PSRR – dB AVDD = DVDD = 3.3V fSAMPLE = 200kHz fIN = 10kHz SNR = 72.04dB THD = –88.43dB 3.3V –84 –40 SNR – dB –86 5.0V –60 –88 –80 –90 0 –100 20 40 60 INPUT FREQUENCY – kHz 80 100 Figure 20. PSRR vs. Frequency –120 0 20 40 60 FREQUENCY – kHz 80 100 Figure 18. FFT Plot Figure 19 shows the SNR vs. Frequency for different supplies and different external references. 74 AVDD = DVDD WITH 2.5V REFERENCE UNLESS STATED OTHERWISE S(N+D) RATIO – dB 73 5.0V SUPPLIES, WITH 5V REFERENCE 72 5.0V SUPPLIES 5.0V SUPPLIES, L VERSION 71 3.3V SUPPLIES 70 69 0 20 40 60 INPUT FREQUENCY – kHz 80 100 Figure 19. SNR vs. Frequency Figure 20 shows the Power Supply Rejection Ratio vs. Frequency for the part. The Power Supply Rejection Ratio is defined as the ratio of the power in adc output at frequency f to the power of a full-scale sine wave. PSRR (dB) = 10 log (Pf/Pfs) Pf = Power at frequency f in adc output, Pfs = power of a full-scale sine wave. Here a 100 mV peak-to-peak sine wave is coupled onto the AVDD supply while the digital supply is left unaltered. Both the 3.3 V and 5.0 V supply performances are shown. POWER-DOWN OPTIONS The AD7858 provides flexible power management to allow the user to achieve the best power performance for a given throughput rate. The power management options are selected by programming the power management bits, PMGT1 and PMGT0, in the control register and by use of the SLEEP pin. Table VI summarizes the power-down options that are available and how they can be selected by using either software, hardware, or a combination of both. The AD7858 can be fully or partially powered down. When fully powered down, all the on-chip circuitry is powered down and IDD is 1 µA typ. If a partial powerdown is selected, then all the on-chip circuitry except the reference is powered down and IDD is 400 µA typ. The choice of full or partial power-down does not give any significant improvement in throughput with a power-down between conversions. This is discussed in the next section–Power-Up Times. However, a partial power-down does allow the on-chip reference to be used externally even though the rest of the AD7858 circuitry is powered down. It also allows the AD7858 to be powered up faster after a long power-down period when using the on-chip reference (See Power-Up Times–Using On-Chip Reference). When using the SLEEP pin, the power management bits PMGT1 and PMGT0 should be set to zero (default status on power-up). Bringing the SLEEP pin logic high ensures normal operation, and the part does not power down at any stage. This may be necessary if the part is being used at high throughput rates when it is not possible to power down between conversions. If the user wishes to power down between conversions at lower throughput rates (i.e. <100 kSPS for the AD7858) to achieve better power performances, then the SLEEP pin should be tied logic low. If the power-down options are to be selected in software only, then the SLEEP pin should be tied logic high. By setting the power management bits PMGT1 and PMGT0 as shown in Table VI, a Full Power-Down, Full Power-Up, Full PowerDown Between Conversions, and a Partial Power-Down Between Conversions can be selected. –18– REV. B AD7858/AD7858L Table VI. Power Management Options PMGT1 PMGT0 SLEEP Bit Bit Pin 0 0 Comment 0 0 0 0 1 1 X 1 1 0 1 X X Full Power-Down if Not Calibrating or Converting (Default Condition After Power-On) Normal Operation Normal Operation (Independent of the SLEEP Pin) Full Power-Down Partial Power-Down if Not Converting A typical connection diagram for a low power application is shown in Figure 21 (AD7858L is the low power version of the AD7858). ANALOG SUPPLY +3V CURRENT, I = 1.5mA TYP 10F 0.1F 0.1F AVDD DVDD 0V TO 2.5V INPUT AIN(+) CLKIN AD7858/ AD7858L CREF1 CONVST 0.01F CREF2 SCLK AUTO POWER DOWN AFTER CONVERSION 0.01F AUTO CAL ON POWER-UP MASTER CLOCK INPUT SLEEP 100kHz PULSE GENERATOR START CONVERSION ON RISING EDGE 5s CONVERSION START INPUT CONVST tCONVERT SERIAL CLOCK INPUT BUSY CAL DOUT AGND DIN SERIAL DATA OUTPUT LOW POWER C/P SERIAL DATA INPUT REFIN /REFOUT INTERNAL REFERENCE 0.1F REF192 POWER-UP NORMAL FULL TIME OPERATION POWER-DOWN SYNC DGND OPTIONAL EXTERNAL REFERENCE Figure 21. Typical Low Power Circuit POWER-UP TIMES Using an External Reference When the AD7858 is powered up, the part is powered up from one of two conditions. First, when the power supplies are initially powered up and, secondly, when the part is powered up from either a hardware or software power-down (see last section). When AVDD and DVDD are powered up, the AD7858 should be left idle for approximately 32 ms (4 MHz CLK) to allow for the autocalibration if a 10 nF cap is placed on the CAL pin, (see Calibration section). During power-up the functionality of the SLEEP pin is disabled, i.e., the part will not power down until the end of the calibration if SLEEP is tied logic low. The autocalibration on power-up can be disabled if the CAL pin is tied to REV. B The AD7858 powers up from a full hardware or software power-down in 5 µs typ. This limits the throughput which the part is capable of to 104 kSPS for the AD7858 operating with a 4 MHz CLK and 66 kSPS for the AD7858L with a 1.8 MHz CLK when powering down between conversions. Figure 22 shows how power-down between conversions is implemented using the CONVST pin. The user first selects the power-down between conversions option by using the SLEEP pin and the power management bits, PMGT1 and PMGT0, in the control register, (see last section). In this mode the AD7858 automatically enters a full power-down at the end of a conversion, i.e., when BUSY goes low. The falling edge of the next CONVST pulse causes the part to power up. Assuming the external reference is left powered up, the AD7858 should be ready for normal operation 5 µs after this falling edge. The rising edge of CONVST initiates a conversion so the CONVST pulse should be at least 5 µs wide. The part automatically powers down on completion of the conversion. POWER-UP ON FALLING EDGE AIN(–) 0.1F 1.8MHz OSCILLATOR a logic high. If the autocalibration is disabled, then the user must take into account the time required by the AD7858 to power-up before a self-calibration is carried out. This power-up time is the time taken for the AD7858 to power up when power is first applied (300 µs) typ) or the time it takes the external reference to settle to the 12-bit level–whichever is the longer. POWER-UP TIME Figure 22. Power-Up Timing When Using CONVST Pin NOTE: Where the software CONVST is used or automatic full power-down, the part must be powered up in software with an extra write setting PMGT1 = 0 and PMGT0 = 1 before a conversion is initiated in the next write. Automatic partial powerdown after a calibration is not possible; the part must be powered down manually. If software calibrations are to be used when operating in the partial power-down mode, then three separate writes are required. The first initiates the type of calibration required, the second write powers the part down into partial power-down mode, while the third write powers the part up again before the next calibration command is issued. Using the Internal (On-Chip) Reference As in the case of an external reference, the AD7858 can powerup from one of two conditions, power-up after the supplies are connected or power-up from hardware/software power-down. When using the on-chip reference and powering up when AVDD and DVDD are first connected, it is recommended that the powerup calibration mode be disabled as explained above. When using the on-chip reference, the power-up time is effectively the time it takes to charge up the external capacitor on the REFIN/REFOUT pin. This time is given by the equation: tUP = 9 × R × C where R ≅ 150 kΩ and C = external capacitor. –19– AD7858/AD7858L The recommended value of the external capacitor is 100 nF; this gives a power-up time of approximately 135 ms before a calibration is initiated and normal operation should commence. 10 SWITCH OPENS DURING POWER-DOWN REFIN/REFOUT AD7858 ON-CHIP REFERENCE EXTERNAL CAPACITOR BUF TO OTHER CIRCUITRY Figure 23. On-Chip Reference During Power-Down POWER VS. THROUGHPUT RATE The main advantage of a full power-down after a conversion is that it significantly reduces the power consumption of the part at lower throughput rates. When using this mode of operation, the AD7858 is only powered up for the duration of the conversion. If the power-up time of the AD7858 is taken to be 5 µs and it is assumed that the current during power-up is 4 mA typ, then power consumption as a function of throughput can easily be calculated. The AD7858 has a conversion time of 4.6 µs with a 4 MHz external clock. This means the AD7858 consumes 4 mA typ, (or 12 mW typ VDD = 3 V) for 9.6 µs in every conversion cycle if the device is powered down at the end of a conversion. If the throughput rate is 1 kSPS, the cycle time is 1000 µs and the average power dissipated during each cycle is (9.6/1000) × (12 mW) = 115 µW. The graph, Figure 24, shows the power consumption of the AD7858 as a function of throughput. Table VII lists the power consumption for various throughput rates. POWER – mW AD7858 (4MHz CLK) When CREF is fully charged, the power-up time from a hardware or software power-down reduces to 5 µs. This is because an internal switch opens to provide a high impedance discharge path for the reference capacitor during power-down—see Figure 23. An added advantage of the low charge leakage from the reference capacitor during power-down is that even though the reference is being powered down between conversions, the reference capacitor holds the reference voltage to within 0.5 LSBs with throughput rates of 100 samples/second and over with a full power-down between conversions. A high input impedance op amp like the AD707 should be used to buffer this reference capacitor if it is being used externally. Note, if the AD7858 is left in its power-down state for more than 100 ms, the charge on CREF will start to leak away and the power-up time will increase. If this long power-up time is a problem, the user can use a partial power-down for the last conversion so the reference remains powered up. Power 1 kSPS 10 kSPS 115 µW 1.15 mW AD7858L (1.8MHz CLK) 0.1 0.01 0 5 10 15 25 35 20 30 THROUGHPUT – kSPS 40 45 50 Figure 24. Power vs. Throughput Rate CALIBRATION SECTION Calibration Overview The automatic calibration that is performed on power-up ensures that the calibration options covered in this section will not be required in a significant amount of applications. The user will not have to initiate a calibration unless the operating conditions change (CLKIN frequency, analog input mode, reference voltage, temperature, and supply voltages). The AD7858/ AD7858L have a number of calibration features that may be required in some applications and there are a number of advantages in performing these different types of calibration. First, the internal errors in the ADC can be reduced significantly to give superior dc performance, and secondly, system offset and gain errors can be removed. This allows the user to remove reference errors (whether it be internal or external reference) and to make use of the full dynamic range of the AD7858/ AD7858L by adjusting the analog input range of the part for a specific system. There are two main calibration modes on the AD7858/AD7858L, self-calibration and system calibration. There are various options in both self-calibration and system calibration as outlined previously in Table IV. All the calibration functions can be initiated by pulsing the CAL pin or by writing to the control register and setting the STCAL bit to one. The timing diagrams that follow involve using the CAL pin. The duration of each of the different types of calibrations is given in Table VIII for the AD7858 with a 4 MHz master clock. These calibration times are master clock dependent. Therefore, the calibrating times for the AD7858L (CLKIN = 1.8 MHz) will be longer than those quoted in Table VIII. Table VII. Power Consumption vs. Throughput Throughput Rate 1 –20– Table VIII. Calibration Times (AD7858 with 4 MHz CLKIN) Type of Self- or System Calibration Time Full Offset + Gain Offset Gain 31.25 ms 6.94 ms 3.47 ms 3.47 ms REV. B AD7858/AD7858L Automatic Calibration on Power-On The CAL pin has a 0.15 µA pull-up current source connected to it internally to allow for an automatic full self-calibration on power-on. A full self-calibration will be initiated on power-on if a capacitor is connected from the CAL pin to DGND. The internal current source connected to the CAL pin charges up the external capacitor and the time required to charge the external capacitor will depend on the size of the capacitor itself. This time should be large enough to ensure that the internal reference is settled before the calibration is performed. A 33 nF capacitor is sufficient to ensure that the internal reference has settled (see Power-Up Times) before a calibration is initiated taking into account trigger level and current source variations on the CAL pin. However, if an external reference is being used, this reference must have stabilized before the automatic calibration is initiated (a larger capacitor on the CAL pin should be used if the external reference has not settled when the autocalibration is initiated). Once the capacitor on the CAL pin has charged, the calibration will be performed which will take 32 ms (4 MHz CLKIN). Therefore the autocalibration should be complete before operating the part. After calibration, the part is accurate to the 12-bit level and the specifications quoted on the data sheet apply. There will be no need to perform another calibration unless the operating conditions change or unless a system calibration is required. Self-Calibration Description There are four different calibration options within the selfcalibration mode. First, there is a full self-calibration where the DAC, internal gain, and internal offset errors are calibrated out. Then, there is the (Gain + Offset) self-calibration which calibrates out the internal gain error and then the internal offset errors. The internal DAC is not calibrated here. Finally, there are the self-offset and self-gain calibrations which calibrate out the internal offset errors and the internal gain errors respectively. The internal capacitor DAC is calibrated by trimming each of the capacitors in the DAC. It is the ratio of these capacitors to each other that is critical, and so the calibration algorithm ensures that this ratio is at a specific value by the end of the calibration routine. For the offset and gain there are two separate capacitors, one of which is trimmed when an offset or gain calibration is performed. Again, it is the ratio of these capacitors to the capacitors in the DAC that is critical and the calibration algorithm ensures that this ratio is at a specified value for both the offset and gain calibrations. For the self- (gain + offset), self-offset, and self-gain calibrations the BUSY line will be triggered high by the rising edge of the CAL signal (or the end of the write to the control register if calibration is initiated in software) and will stay high for the full duration of the self-calibration. The length of time that the BUSY is high will depend on the type of self-calibration that is initiated. Typical figures are given in Table VIII. The timing diagrams for the other self-calibration options will be similar to that outlined in Figure 25. t1 = 100ns MIN, t15 = 2.5 tCLKIN MAX, tCAL = 125013 tCLKIN t1 CAL (I/P) t15 BUSY (O/P) tCAL Figure 25. Timing Diagram for Full Self-Calibration System Calibration Description System calibration allows the user to take out system errors external to the AD7858/AD7858L as well as calibrate the errors of the AD7858/AD7858L itself. The maximum calibration range for the system offset errors is ± 5% of VREF and for the system gain errors is ± 2.5% of VREF. This means that the maximum allowable system offset voltage applied between the AIN(+) and AIN(–) pins for the calibration to adjust out this error is ± 0.05 × VREF (i.e., the AIN(+) can be 0.05 × VREF above AIN(–) or 0.05 × VREF below AIN(–)). For the System gain error the maximum allowable system full-scale voltage that can be applied between AIN(+) and AIN(–) for the calibration to adjust out this error is VREF ± 0.025 × VREF ( i.e., the AIN(+) above AIN(–)). If the system offset or system gain errors are outside the ranges mentioned the system calibration algorithm will reduce the errors as much as the trim range allows. Figures 26 through 28 illustrate why a specific type of system calibration might be used. Figure 26 shows a system offset calibration (assuming a positive offset) where the analog input range has been shifted upwards by the system offset after the system offset calibration is completed. A negative offset may also be accounted for by a system offset calibration. The zero-scale error is adjusted for an offset calibration, and the positive full-scale error is adjusted for a gain calibration. MAX SYSTEM FULL SCALE IS ⴞ2.5% FROM VREF The diagram of Figure 25 shows the timing for a full selfcalibration. Here the BUSY line stays high for the full length of the self-calibration. A self-calibration is initiated by bringing the CAL pin low (which initiates an internal reset) and then high again or by writing to the control register and setting the STCAL bit to 1 (note that if the part is in a power-down mode the CAL pulsewidth must take account of the power-up time ). The BUSY line is triggered high from the rising edge of CAL (or the end of the write to the control register if calibration is initiated in software), and BUSY will go low when the full self-calibration is complete after a time tCAL as shown in Figure 25. REV. B VREF + SYS OFFSET VREF – 1LSB VREF –1LSB Self-Calibration Timing –21– ANALOG INPUT RANGE SYSTEM OFFSET ANALOG INPUT RANGE CALIBRATION SYS OFFSET AGND SYS OFFSET AGND MAX SYSTEM OFFSET IS ⴞ5% OF VREF MAX SYSTEM OFFSET IS ⴞ5% OF VREF Figure 26. System Offset Calibration AD7858/AD7858L Figure 27 shows a system gain calibration (assuming a system full scale greater than the reference voltage) where the analog input range has been increased after the system gain calibration is completed. A system full-scale voltage less than the reference voltage may also be accounted for by a system gain calibration. MAX SYSTEM FULL SCALE IS ⴞ2.5% FROM VREF system (gain + offset) calibrations will be sufficient. If the system errors are large (close to the specified limits of the calibration range) three system (gain + offset) calibrations may be required to reduced the offset and gain errors to at least the 12bit level. There will never be any need to perform more than three system (offset + gain) calibrations. MAX SYSTEM FULL SCALE IS ⴞ2.5% FROM VREF SYS F.S. VREF – 1LSB The zero scale error is adjusted for an offset calibration and the positive full-scale error is adjusted for a gain calibration. SYS F.S. VREF – 1LSB ANALOG INPUT RANGE SYSTEM GAIN System Calibration Timing The calibration timing diagram in Figure 29 is for a full system calibration where the falling edge of CAL initiates an internal reset before starting a calibration (note that if the part is in powerdown mode the CAL pulsewidth must take account of the power-up time). If a full system calibration is to be performed in software it is easier to perform separate gain and offset calibrations so that the CONVST bit in the control register does not have to be programmed in the middle of the system calibration sequence. The rising edge of CAL starts calibration of the internal DAC and causes the BUSY line to go high. If the control register is set for a full system calibration, the CONVST must be used also. The full-scale system voltage should be applied to the analog input pins from the start of calibration. The BUSY line will go low once the DAC and System Gain Calibration are complete. Next the system offset voltage is applied to the AIN pin for a minimum setup time (tSETUP) of 100 ns before the rising edge of the CONVST and remain until the BUSY signal goes low. The rising edge of the CONVST starts the system offset calibration section of the full system calibration and also causes the BUSY signal to go high. The BUSY signal will go low after a time tCAL2 when the calibration sequence is complete. In some applications not all the input channels may be used. In this case it may be useful to dedicate two input channels for the system calibration, one which has the system offset voltage applied to it, and one which has the system full scale voltage applied to it. When a system offset or gain calibration is performed, the channel selected should correspond to the system offset or system full-scale voltage channel. ANALOG INPUT RANGE CALIBRATION AGND AGND Figure 27. System Gain Calibration Finally in Figure 28 both the system offset and gain are accounted for by the a system offset followed by a system gain calibration. First the analog input range is shifted upwards by the positive system offset and then the analog input range is adjusted at the top end to account for the system full scale. MAX SYSTEM FULL SCALE IS ⴞ2.5% FROM VREF MAX SYSTEM FULL SCALE IS ⴞ2.5% FROM VREF SYS F.S. VREF –1LSB ANALOG INPUT RANGE SYS OFFSET AGND VREF + SYS OFFSET SYS F.S. VREF – 1LSB SYSTEM OFFSET CALIBRATION ANALOG FOLLOWED BY INPUT RANGE SYSTEM GAIN CALIBRATION MAX SYSTEM OFFSET IS ⴞ5% OF VREF SYS OFFSET AGND MAX SYSTEM OFFSET IS ⴞ5% OF VREF Figure 28. System (Gain + Offset) Calibration System Gain and Offset Interaction The inherent architecture of the AD7858/AD7858L leads to an interaction between the system offset and gain errors when a system calibration is performed. Therefore, it is recommended to perform the cycle of a system offset calibration followed by a system gain calibration twice. Separate system offset and system gain calibrations reduce the offset and gain errors to at least the 12-bit level. By performing a system offset CAL first and a system gain calibration second, priority is given to reducing the gain error to zero before reducing the offset error to zero. If the system errors are small, a system offset calibration would be performed, followed by a system gain calibration. If the system errors are large (close to the specified limits of the calibration range), this cycle would be repeated twice to ensure that the offset and gain errors were reduced to at least the 12-bit level. The advantage of doing separate system offset and system gain calibrations is that the user has more control over when the analog inputs need to be at the required levels, and the CONVST signal does not have to be used. The timing for a system (gain + offset) calibration is very similar to that of Figure 29 the only difference being that the time tCAL1 will be replaced by a shorter time of the order of tCAL2 as the internal DAC will not be calibrated. The BUSY signal will signify when the gain calibration is finished and when the part is ready for the offset calibration. t1 = 100ns MIN, t14 = 50/90ns MIN 5V/3V, t15 = 2.5 tCLKIN MAX, tCAL1 = 111114 tCLKIN, tCAL2 = 13899 tCLKIN t1 CAL (I/P) t15 BUSY (O/P) tCAL2 tCAL1 Alternatively, a system (gain + offset) calibration can be performed. It is recommended to perform three system (gain + offset) calibrations to reduce the offset and gain errors to the 12-bit level. For the system (gain + offset) calibration priority is given to reducing the offset error to zero before reducing the gain error to zero. Thus if the system errors are small then two –22– t16 CONVST (I/P) tSETUP AIN (I/P) VSYSTEM FULL SCALE VOFFSET Figure 29. Timing Diagram for Full System Calibration REV. B AD7858/AD7858L The timing diagram for a system offset or system gain calibration is shown in Figure 30. Here again the CAL is pulsed and the rising edge of the CAL initiates the calibration sequence (or the calibration can be initiated in software by writing to the control register). The rising edge of the CAL causes the BUSY line to go high and it will stay high until the calibration sequence is finished. The analog input should be set at the correct level for a minimum setup time (tSETUP) of 100 ns before the rising edge of CAL and stay at the correct level until the BUSY signal goes low. t1 CAL (I/P) t15 tCAL2 VSYSTEM FULL SCALE OR VSYSTEM OFFSET AIN (I/P) When writing to the part via the DIN line there is the possibility of writing data into the incorrect registers, such as the test register for instance, or writing the incorrect data and corrupting the serial interface. The SYNC pin acts as a reset. Bringing the SYNC pin high resets the internal shift register. The first data bit after the next SYNC falling edge will now be the first bit of a new 16-bit transfer. It is also possible that the test register contents were altered when the interface was lost. Therefore, once the serial interface is reset it may be necessary to write the 16-bit word 0100 0000 0000 0010 to restore the test register to its default value. Now the part and serial interface are completely reset. It is always useful to retain the ability to program the SYNC line from a port of the µController/DSP to have the ability to reset the serial interface. Table X summarizes the interface modes provided by the AD7858/AD7858L. It also outlines the various µP/µC to which the particular interface is suited. BUSY (O/P) tSETUP Resetting the Serial Interface Interface Mode 1 may only be set by programming the control register (see section on Control Register). Figure 30. Timing Diagram for System Gain or System Offset Calibration Some of the more popular µProcessors, µControllers, and the DSP machines that the AD7858/AD7858L will interface to directly are mentioned here. This does not cover all µCs, µPs, and DSPs. A more detailed timing description on each of the interface modes follows. SERIAL INTERFACE SUMMARY Table IX details the two interface modes and the serial clock edges from which the data is clocked out by the AD7858/ AD7858L (DOUT Edge) and that the data is latched in on (DIN Edge). Table X. Interface Mode Description In both interface Modes 1 and 2 the SYNC is gated with the SCLK. Thus the SYNC↓ may clock out the MSB of data. Subsequent bits will be clocked out by the Serial Clock, SCLK. The condition for the SYNC↓ clocking out the MSB of data is as follows: The falling edge of SYNC will clock out the MSB if the serial clock is low when the SYNC goes low. If this condition is not the case, the SCLK will clock out the MSB. If a noncontinuous SCLK is used, it should idle high. Table IX. SCLK Active Edges Interface Mode Edge DOUT Edge DIN 1, 2 SCLK↓ SCLK↑ REV. B –23– Interface Mode Processor/ Controller Comment 1 8XC51 8XL51 PIC17C42 (2-Wire) (DIN Is an Input/ Output Pin) 2 68HC11 68L11 68HC16 PIC16C64 ADSP21xx DSP56000 DSP56001 DSP56002 DSP56L002 (3-Wire, SPI) (Default Mode) AD7858/AD7858L automatically revert back to an input after a time, t14. Note that a continuous SCLK shown by the dotted waveform in Figure 35 can be used provided that the SYNC is low for only 16 clock pulses in each of the read and write cycles. DETAILED TIMING SECTION Mode 1 (2-Wire 8051 Interface) The read and writing takes place on the DIN line and the conversion is initiated by pulsing the CONVST pin (note that in every write cycle the 2/3 MODE bit must be set to 1). The conversion may be started by setting the CONVST bit in the control register to 1 instead of using the CONVST pin. Below in Figure 31 and in Figure 32 are the timing diagrams for Operating Mode 1 in Table X where we are in the 2-wire interface mode. Here the DIN pin is used for both input and output as shown. The SYNC input is level triggered active low and can be pulsed (Figure 31) or can be constantly low (Figure 32). In Figure 31 the part samples the input data on the rising edge of SCLK. After the 16th rising edge of SCLK the DIN is configured as an output. When the SYNC is taken high the DIN is three-stated. Taking SYNC low disables the three-state on the DIN pin and the first SCLK falling edge clocks out the first data bit. Once the 16 clocks have been provided the DIN pin will In Figure 32 the SYNC line is tied low permanently and this results in a different timing arrangement. With SYNC tied low permanently the DIN pin will never be three-stated. The 16th rising edge of SCLK configures the DIN pin as an input or an output as shown in the diagram. Here no more than 16 SCLK pulses must occur for each of the read and write operations. If reading from and writing to the calibration registers in this interface mode, all the selected calibration registers must be read from or written to. The read and write operations cannot be aborted. When reading from the calibration registers, the DIN pin will remain as an output for the full duration of all the calibration register read operations. When writing to the calibration registers, the DIN pin will remain as an input for the full duration of all the calibration register write operations. t3 = –0.4tSCLK MIN (NONCONTINUOUS SCLK) ⴞ0.4tSCLK ns MIN/MAX (CONTINUOUS SCLK), t6 = 75/115ns MAX (5V/3V), t7 = 40/60ns MIN (5V/3V), t8 = 20/30ns MIN (5V/3V) POLARITY PIN LOGIC HIGH SYNC (I/P) t11 t3 t11 t3 1 SCLK (I/P) 16 t7 t8 DIN (I/O) 1 16 t5 DB15 t14 t6 t12 DB0 t6 DB15 DB0 THREE-STATE DATA WRITE DATA READ DIN BECOMES AN OUTPUT DIN BECOMES AN INPUT Figure 31. Timing Diagram for Read/Write Operation with DIN as an Input/Output (i.e., Mode 1) t6 = 75/115ns MAX (5V/3V), t7 = 40/60ns MIN (5V/3V), t8 = 20/30ns MIN (5V/3V), t13 = 90/130ns MAX (5V/3V), t14 = 50/90ns MIN (5V/3V) POLARITY PIN LOGIC HIGH SCLK (I/P) 1 16 t7 t8 DIN (I/O) 1 t6 t13 DB15 16 6 t14 t6 DB0 DB15 DB0 DATA WRITE DATA READ DIN BECOMES AN INPUT Figure 32. Timing Diagram for Read/Write Operation with DIN as an Input/Output and SYNC Input Tied Low (i.e., Interface Mode 1) –24– REV. B AD7858/AD7858L SYNC going low disables the three-state on the DOUT pin. The first falling edge of the SCLK after the SYNC going low clocks out the first leading zero on the DOUT pin. The DOUT pin is three-stated again a time t12 after the SYNC goes high. With the DIN pin the data input has to be set up a time t7 before the SCLK rising edge as the part samples the input data on the SCLK rising edge in this case. If resetting the interface is required, the SYNC must be taken high and then low. Mode 2 (3-Wire SPI/QSPI Interface Mode) This is the DEFAULT INTERFACE MODE. In Figure 33 below we have the timing diagram for interface Mode 2 which is the SPI/QSPI interface mode. Here the SYNC input is active low and may be pulsed or tied permanently low. If SYNC is permanently low, 16 clock pulses must be applied to the SCLK pin for the part to operate correctly, otherwise with a pulsed SYNC input a continuous SCLK may be applied provided SYNC is low for only 16 SCLK cycles. In Figure 33 the t3 = –0.4tSCLK MIN (NONCONTINUOUS SCLK) ⴞ0.4tSCLK ns MIN/MAX (CONTINUOUS SCLK), t6 = 75/115ns MAX (5V/3V), t7 = 40/60ns MIN (5V/3V), t8 = 20/30ns MIN (5V/3V), t11 = 30/50ns MIN (NONCONTINUOUS SCLK) (5V/3V), (30/50)/0.4tSCLK ns MIN/MAX POLARITY PIN LOGIC HIGH (CONTINUOUS SCLK) (5V/3V) SYNC (I/P) t11 t3 SCLK (I/P) t9 1 2 3 4 THREE-STATE DB15 t7 DIN (I/P) 6 16 t12 t6 t6 DOUT (O/P) 5 t10 t5 DB15 DB14 DB13 DB12 DB11 DB0 THREE-STATE t8 t8 DB14 DB10 DB13 DB12 DB11 DB10 DB0 Figure 33. SPI/QSPI Mode 2 Timing Diagram for Read/Write Operation with DIN Input, DOUT Output, and SYNC Input REV. B –25– AD7858/AD7858L CONFIGURING THE AD7858/AD7858L The AD7858/AD7858L contains 14 on-chip registers which can be accessed via the serial interface. In the majority of applications it will not be necessary to access all of these registers. Here the CLKIN signal is applied directly after power-on; the CLKIN signal must be present to allow the part to perform a calibration. This automatic calibration will be completed approximately 32 ms after the AD7858 has powered up (4 MHz CLK). For accessing the on-chip registers it is necessary to write to the part. To change the channel from the default channel setting the user will be required to write to the part. To enable Serial Interface Mode 1 the user must also write to the part. Figure 34 and 35 outline flowcharts of how to configure the AD7858/ AD7858L Serial Interface Modes 1 and 2 respectively. The continuous loops on all diagrams indicate the sequence for more than one conversion. The options of using a hardware (pulsing the CONVST pin) or software (setting the CONVST bit to 1) conversion start, and reading/writing during or after conversion are shown in Figures 34 and 35. If the CONVST pin is never used then it should be tied to DVDD permanently. Where reference is made to the BUSY bit equal to a Logic 0, to indicate the end of conversion, the user in this case would poll the BUSY bit in the status register. Interface Mode 1 Configuration Figure 34 shows the flowchart for configuring the part in Interface Mode 1. This mode of operation can only be enabled by writing to the control register and setting the 2/3 MODE bit. Reading and writing cannot take place simultaneously in this mode as the DIN pin is used for both reading and writing. START POWER-ON, APPLY CLKIN SIGNAL, WAIT FOR AUTOMATIC CALIBRATION SERIAL INTERFACE MODE ? 1 YES INITIATE CONVERSION IN SOFTWARE ? NO APPLY SYNC (IF REQUIRED), SCLK, WRITE TO CONTROL REGISTER SETTING CHANNEL TWO-WIRE MODE APPLY SYNC (IF REQUIRED), SCLK, WRITE TO CONTROL REGISTER SETTING CHANNEL AND TWO-WIRE MODE WRITE TO CONTROL REGISTER SETTING CONVST BIT TO 1 (SEE NOTE) PULSE CONVST PIN YES WAIT APPROX. 200ns AFTER CONVST RISING EDGE OR AFTER END OF CONTROL REGISTER WRITE READ DATA DURING CONVERSION ? NO WAIT FOR BUSY SIGNAL TO GO LOW OR WAIT FOR BUSY BIT = 0 APPLY SYNC (IF REQUIRED), SCLK, READ PREVIOUS CONVERSION RESULT ON DIN PIN APPLY SYNC (IF REQUIRED), SCLK, READ CURRENT CONVERSION RESULT ON DIN PIN NOTE: TWO SEPARATE WRITES ARE REQUIRED TO SET A NEW CHANNEL ADDRESS AND INITIATE A CONVERSION ON THAT NEW CHANNEL IN SOFTWARE AS THE ACQUISITION TIME (2 tCLKIN) MUST ELAPSE BEFORE THE CONVERSION BEGINS. IF BOTH COMMANDS ARE ISSUED IN THE ONE WRITE THE RESULT OF THIS CONVERSION SHOULD BE DISCARDED AND THE NEXT CONVERSION ON THAT SAME CHANNEL WILL PROVIDE CORRECT RESULTS. Figure 34. Flowchart for Setting Up, Reading, and Writing in Interface Mode 1 –26– REV. B AD7858/AD7858L that no valid data is written to any of the registers. When using the software conversion start and transferring data during conversion Note 1 must be obeyed. Interface Mode 2 Configuration Figure 35 shows the flowchart for configuring the part in Interface Mode 2. In this case the read and write operations take place simultaneously via the serial port. Writing all 0s ensures START POWER-ON, APPLY CLKIN SIGNAL, WAIT FOR AUTOMATIC CALIBRATION SERIAL INTERFACE MODE ? 2 INITIATE CONVERSION IN SOFTWARE ? YES NO PULSE CONVST PIN TRANSFER DATA DURING CONVERSION ? YES APPLY SYNC (IF REQUIRED), SCLK, WRITE TO CONTROL REGISTER SETTING CHANNEL, (SEE NOTE 1) NO YES WAIT APPROX 200ns AFTER CONVST RISING EDGE APPLY SYNC (IF REQUIRED), SCLK, READ PREVIOUS CONVERSION RESULT ON DOUT PIN, AND WRITE CHANNEL SELECTION APPLY SYNC (IF REQUIRED), SCLK, WRITE TO CONTROL REGISTER SETTING CHANNEL TRANSFER DATA DURING CONVERSION ? WRITE TO CONTROL REGISTER SETTING CONVST BIT TO 1, READ PREVIOUS RESULT ON DOUT PIN (SEE NOTES 1&2) WRITE TO CONTROL REGISTER SETTING CONVST BIT TO 1, READ CURRENT CONVERSION RESULT ON DOUT PIN (SEE NOTE 2) NO WAIT FOR BUSY SIGNAL TO GO LOW OR WAIT FOR BUSY BIT = 0 WAIT FOR BUSY SIGNAL TO GO LOW OR WAIT FOR BUSY BIT = 0 APPLY SYNC (IF REQUIRED), SCLK, READ CURRENT CONVERSION RESULT ON DOUT PIN, AND WRITE CHANNEL SELECTION NOTES 1WHEN USING THE SOFTWARE CONVERSION START AND TRANSFERRING DATA DURING CONVERSION THE USER MUST ENSURE THE CONTROL REGISTER WRITE OPERATION EXTENDS BEYOND THE FALLING EDGE OF BUSY. THE FALLING EDGE OF BUSY RESETS THE CONVST BIT TO 0 AND ONLY AFTER THIS TIME CAN IT BE REPROGRAMMED TO 1 TO START THE NEXT CONVERSION. 2TWO SEPARATE WRITES ARE REQUIRED TO SET A NEW CHANNEL ADDRESS AND INITIATE A CONVERSION ON THAT NEW CHANNEL IN SOFTWARE AS THE ACQUISITION TIME (2 tCLKIN) MUST ELAPSE BEFORE THE CONVERSION BEGINS. IF BOTH COMMANDS ARE ISSUED IN THE ONE WRITE THE RESULT OF THIS CONVERSION SHOULD BE DISCARDED AND THE NEXT CONVERSION ON THAT SAME CHANNEL WILL PROVIDE CORRECT RESULTS. Figure 35. Flowchart for Setting Up, Reading, and Writing in Interface Mode 2 REV. B –27– AD7858/AD7858L MICROPROCESSOR INTERFACING OPTIONAL In many applications, the user may not require the facility of writing to most of the on-chip registers. The only writing necessary is to set the input channel configuration. After this the CONVST is applied, a conversion is performed, and the result may be read using the SCLK to clock out the data from the output register on to the DOUT pin. At the same time a write operation occurs and this may consist of all 0s where no data is written to the part or may set a different input channel configuration for the next conversion. The SCLK may be connected to the CLKIN pin if the user does not want to have to provide separate serial and master clocks. With this arrangement the SYNC signal must be low for 16 SCLK cycles for the read and write operations. CONVST CLKIN 4MHz/1.8MHz 8XC51/L51 MASTER SYNC DIN DOUT CONVST CLKIN P3.1 SCLK P3.0 DIN (INT0/P3.2) OPTIONAL SLAVE BUSY SYNC Figure 37. 8XC51/PIC16C42 Interface AD7858/AD7858L to 68HC11/16/L11/PIC16C42 Interface CONVERSION START 4MHz/1.8MHz MASTER CLOCK SCLK AD7858/ AD7858L AD7858/AD7858L SYNC SIGNAL TO GATE THE SCLK SERIAL DATA INPUT SERIAL DATA OUTPUT Figure 36. Simplified Interface Diagram AD7858/AD7858L to 8XC51 Interface Figure 37 shows the AD7858/AD7858L interface to the 8XC51. The 8XL51 is for interfacing to the AD7858/AD7858L when the supply is at 3 V. The 8XC51 only runs at 5 V. The 8XC51 is in Mode 0 operation. This is a two-wire interface consisting of the SCLK and the DIN which acts as a bidirectional line. The SYNC is tied low. The BUSY line can be used to give an interrupt driven system but this would not normally be the case with the 8XC51. For the 8XC51 12 MHz version the serial clock will run at a maximum of 1 MHz so the serial interface of the AD7858/AD7858L will only be running at 1 MHz. The CLKIN signal must be provided separately to the AD7858/AD7858L from a port line on the 8XC51 or from a source other than the 8XC51. Here the SCLK cannot be tied to the CLKIN as the SYNC is tied low permanently. The CONVST signal can be provided from an external timer or conversion can be started in software if required. The sequence of events would typically be to write to the control register via the DIN line setting a conversion start and the 2-wire interface mode (this would be performed in two 8-bit writes), wait for the conversion to be finished (4.6 µs with 4 MHz CLKIN), read the conversion result data on the DIN line (this would be performed in two 8-bits reads), and repeat the sequence. The maximum serial frequency will be determined by the data access and hold times of the 8XC51 and the AD7858/AD7858L. Figure 38 shows the AD7858/AD7858L SPI/QSPI interface to the 68HC11/16/L11/PIC16C42. The 68L11 is for interfacing to the AD7858/AD7858L when the supply is 3 V. The AD7858/ AD7858L is in Interface Mode 2. The SYNC line is not used and is tied to DGND. The µController is configured as the master, by setting the MSTR bit in the SPCR to 1, and provides the serial clock on the SCK pin. For all the µControllers the CPOL bit is set to 1 and for the 68HC11/16/L11 the CPHA bit is set to 1. The CLKIN and CONVST signals can be supplied from the µController or from separate sources. The BUSY signal can be used as an interrupt to tell the µController when the conversion is finished, then the reading and writing can take place. If required the reading and writing can take place during conversion and there will be no need for the BUSY signal in this case. OPTIONAL AD7858/AD7858L 4MHz/1.8MHz 68HC11/L11/16 DVDD CLKIN SPI SS MASTER SYNC HC16, QSPI SCK MOSI SLAVE SCLK MISO IRQ CONVST DOUT OPTIONAL BUSY DIN Figure 38. 68HC11 and 68HC16 Interface For the 68HC16 the word length should be set to 16 bits, and the SS line should be tied to the SYNC pin for the QSPI interface. The micro-sequencer and RAM associated with the 68HC16 QSPI port can be used to perform a number of read and write operations, and store the conversion results in memory, independent of the CPU. This is especially useful when reading the conversion results from all eight channels consecutively. The command section of the QSPI port RAM would be programmed to perform a conversion on one channel, read the conversion result, perform a conversion on the next channel, read the conversion result, and so on until all eight conversion results are stored into the QSPI RAM. –28– REV. B AD7858/AD7858L A typical sequence of events would be to write to the control register via the DIN line setting a conversion start and at the same time reading data from the previous conversion on the DOUT line (both the read and write operations would each be two 8-bit operations, one 16-bit operation for the 68HC16), wait for the conversion to be finished (= 4.6 µs for AD7858 with 4 MHz CLKIN), and then repeat the sequence. The maximum serial frequency will be determined by the data access and hold times of the µControllers and the AD7858/AD7858L. AD7858/AD7858L to ADSP-21xx Interface Figure 39 shows the AD7858/AD7858L interface to the ADSP21xx. The ADSP-21xx is the master and the AD7858/AD7858L is the slave. The AD7858/AD7858L is in Interface Mode 2. For the ADSP-21xx the bits in the serial port control register should be set up as TFSR = RFSR = 1 (need a frame sync for every transfer), SLEN = 15 (16-bit word length), TFSW = RFSW = 1 (alternate framing mode for transmit and receive operations), INVRFS = INVTFS = 1 (active low RFS and TFS), IRFS = 0, ITFS = 1 (External RFS and internal TFS), and ISCLK = 1 (internal serial clock). The CLKIN and CONVST signals can be supplied from the ADSP-21xx or from an external source. The serial clock from the ADSP-21xx must be inverted before the SCLK pin of the AD7858/AD7858L. This SCLK could also be used to drive the CLKIN input of the AD7858/AD7858L. The BUSY signal indicates when the conversion is finished and may not be required. The data access and hold times of the ADSP-21xx and the AD7858/AD7858L allow for a serial clock of 4 MHz/1.8 MHz at 5 V and 3.3 MHz/ 1.8 MHz at 3 V supplies. AD7858/AD7858L to DSP56000/1/2/L002 Interface Figure 40 shows the AD7858/AD7858L to DSP56000/1/2/ L002 interface. Here the DSP5600x is the master and the AD7858 is the slave. The AD7858/AD7858L is in Interface Mode 2. The DSP56L002 is used when the AD7858/AD7858L is being operated at 3 V. The setting of the bits in the registers of the DSP5600x would be for synchronous operation (SYN = 1), internal frame sync (SCD2 = 1), gated internal clock (GCK = 1, SCKD = 1), 16-bit word length (WL1 = 1, WL0 = 0). Since a gated clock is used here the SCLK cannot be tied to the CLKIN of the AD7858/AD7858L. The SCLK from the DSP5600x must be inverted before it is applied to the AD7858/AD7858L. Again the data access and hold times of the DSP5600x and the AD7858/AD7858L allows for a SCLK of 4 MHz/1.8 MHz. OPTIONAL AD7858/AD7858L CONVST ADSP-21xx 4MHz/1.8MHz SCK MASTER CLKIN SCLK DR DOUT RFS SYNC SLAVE TFS IRQ DT OPTIONAL BUSY DIN Figure 39. ADSP-21xx Interface REV. B –29– OPTIONAL AD7858/AD7858L 4MHz/1.8MHz DSP56000/1/2/L002 MASTER CONVST CLKIN SCK SCLK SRD DOUT SYNC SC2 IRQ STD SLAVE OPTIONAL BUSY DIN Figure 40. DSP56000/1/2 Interface AD7858/AD7858L APPLICATION HINTS Grounding and Layout The analog and digital supplies to the AD7858/AD7858L are independent and separately pinned out to minimize coupling between the analog and digital sections of the device. The part has very good immunity to noise on the power supplies as can be seen by the PSRR vs. Frequency graph. However, care should still be taken with regard to grounding and layout. The printed circuit board that houses the AD7858/AD7858L should be designed such that the analog and digital sections are separated and confined to certain areas of the board. This facilitates the use of ground planes that can be separated easily. A minimum etch technique is generally best for ground planes as it gives the best shielding. Digital and analog ground planes should only be joined in one place. If the AD7858/AD7858L is the only device requiring an AGND to DGND connection, then the ground planes should be connected at the AGND and DGND pins of the AD7858/AD7858L. If the AD7858/ AD7858L is in a system where multiple devices require AGND to DGND connections, the connection should still be made at one point only, a star ground point which should be established as close as possible to the AD7858/AD7858L. Avoid running digital lines under the device as these will couple noise onto the die. The analog ground plane should be allowed to run under the AD7858/AD7858L to avoid noise coupling. The power supply lines to the AD7858/AD7858L should use as large a trace as possible to provide low impedance paths and reduce the effects of glitches on the power supply line. Fast switching signals like clocks should be shielded with digital ground to avoid radiating noise to other sections of the board, and clock signals should never be run near the analog inputs. Avoid crossover of digital and analog signals. Traces on opposite sides of the board should run at right angles to each other. This will reduce the effects of feedthrough through the board. A microstrip technique is by far the best but is not always possible with a double-sided board. In this technique, the component side of the board is dedicated to ground planes while signals are placed on the solder side. Good decoupling is also important. All analog supplies should be decoupled with 10 µF tantalum in parallel with 0.1 µF capacitors to AGND. All digital supplies should have a 0.1 µF disc ceramic capacitor to AGND. To achieve the best from these decoupling components, they must be placed as close as possible to the device, ideally right up against the device. In systems where a common supply voltage is used to drive both the AVDD and DVDD of the AD7858/AD7858L, it is recommended that the system’s AVDD supply be used. In this case there should be a 10 Ω resistor between the AVDD pin and DVDD pin. This supply should have the recommended analog supply decoupling capacitors between the AVDD pin of the AD7858/AD7858L and AGND and the recommended digital supply decoupling capacitor between the DVDD pin of the AD7858/AD7858L and DGND. Evaluating the AD7858/AD7858L Performance The recommended layout for the AD7858/AD7858L is outlined in the evaluation board for the AD7858/AD7858L. The evaluation board package includes a fully assembled and tested evaluation board, documentation, and software for controlling the board from the PC via the EVAL-CONTROL BOARD. The EVAL-CONTROL BOARD can be used in conjunction with the AD7858/AD7858L Evaluation board, as well as many other Analog Devices evaluation boards ending in the CB designator, to demonstrate/evaluate the ac and dc performance of the AD7858/AD7858L. The software allows the user to perform ac (fast Fourier transform) and dc (histogram of codes) tests on the AD7858/ AD7858L. It also gives full access to all the AD7858/AD7858L on-chip registers allowing for various calibration and powerdown options to be programmed. AD785x Family All parts are 12 bits, 200 kSPS, 3.0 V to 5.5 V. AD7853 – Single Channel Serial AD7854 – Single Channel Parallel AD7858 – Eight Channel Serial AD7859 – Eight Channel Parallel –30– REV. B AD7858/AD7858L PAGE INDEX Topic Page No. FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Self-Calibration Description . . . . . . . . . . . . . . . . . . . . . . . 21 GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 1 Self-Calibration Timing . . . . . . . . . . . . . . . . . . . . . . . . . . 21 PRODUCT HIGHLIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . 1 System Calibration Description . . . . . . . . . . . . . . . . . . . . 21 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 System Gain and Offset Interaction . . . . . . . . . . . . . . . . . 22 TIMING SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . 4 System Calibration Timing . . . . . . . . . . . . . . . . . . . . . . . 22 TYPICAL TIMING DIAGRAMS . . . . . . . . . . . . . . . . . . . . 5 SERIAL INTERFACE SUMMARY . . . . . . . . . . . . . . . . . . 23 ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . 6 Resetting The Serial Interface . . . . . . . . . . . . . . . . . . . . . 23 ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 DETAILED TIMING SECTION PIN CONFIGURATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Mode 1 (2-Wire 8051 Interface) . . . . . . . . . . . . . . . . . . . 24 PIN FUNCTION DESCRIPTIONS . . . . . . . . . . . . . . . . . . 7 Mode 2 (3-Wire SPI/QSPI Interface) . . . . . . . . . . . . . . . . 25 TERMINOLOGY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 CONFIGURING THE AD7858/AD7858L . . . . . . . . . . . . 26 ON-CHIP REGISTERS Interface Mode 1 Configuration . . . . . . . . . . . . . . . . . . . . 26 Addressing the On-Chip Registers . . . . . . . . . . . . . . . . . . . 9 Interface Mode 2 Configuration . . . . . . . . . . . . . . . . . . . . 27 CONTROL REGISTER . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 MICROPROCESSOR INTERFACING . . . . . . . . . . . . . . . 28 STATUS REGISTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 AD7858/AD7858L–8XC51 Interface . . . . . . . . . . . . . . . 28 CALIBRATION REGISTERS . . . . . . . . . . . . . . . . . . . . . . 13 AD7858/AD7858L–68HC11/16/L11/PIC16C42 Addressing the Calibration Registers . . . . . . . . . . . . . . . . 13 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Writing to/Reading from the Calibration Registers . . . . . . 13 AD7858/AD7858L–ADSP-21xx Interface . . . . . . . . . . . . 29 Adjusting the Offset Calibration Registers . . . . . . . . . . . . 14 AD7858/AD7858L–DSP56000/1/2/L002 Interface . . . . . 29 Adjusting the Gain Calibration Register . . . . . . . . . . . . . . 14 APPLICATION HINTS CIRCUIT INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . 15 Grounding and Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 CONVERTER DETAILS . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Evaluating the AD7858/AD7858L Performance . . . . . . . 30 TYPICAL CONNECTION DIAGRAM . . . . . . . . . . . . . . 15 INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 ANALOG INPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . 32 Acquisition Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 DC/AC Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Input Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Transfer Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 REFERENCE SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . 17 PERFORMANCE CURVES . . . . . . . . . . . . . . . . . . . . . . . . 18 POWER-DOWN OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . 18 POWER-UP TIMES Using an External Reference . . . . . . . . . . . . . . . . . . . . . . 19 Using the Internal (On-Chip) Reference . . . . . . . . . . . . . 19 POWER VS. THROUGHPUT RATE . . . . . . . . . . . . . . . . 20 CALIBRATION SECTION Calibration Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Automatic Calibration on Power-On . . . . . . . . . . . . . . . . 21 REV. B TABLE INDEX # Title Page No. Table I. Write Register Addressing . . . . . . . . . . . . . . . . . 9 Table II. Read Register Addressing . . . . . . . . . . . . . . . . . 9 Table III. Channel Selection . . . . . . . . . . . . . . . . . . . . . . 11 Table IV. Calibration Selection . . . . . . . . . . . . . . . . . . . . 11 Table V. Calibration Register Addressing . . . . . . . . . . . 13 Table VI. Power Management Options . . . . . . . . . . . . . . 19 Table VII. Power Consumption vs. Throughput . . . . . . . 20 Table VIII. Calibration Times (AD7858 with 4 MHz CLKIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Table IX. SCLK Active Edges . . . . . . . . . . . . . . . . . . . . . 23 Table X. Interface Mode Description . . . . . . . . . . . . . . . 23 –31– AD7858/AD7858L OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 24-Lead Plastic DIP (N-24) 24 13 1 12 0.260 ⴞ0.001 (6.61 ⴞ0.03) C01337–0–6/00 1.228 (31.19) 1.226 (31.14) 0.32 (8.128) 0.30 (7.62) PIN 1 0.130 (3.30) 0.128 (3.25) 0.02 (0.5) 0.016 (0.41) 0.11 (2.79) 0.09 (2.28) 0.07 (1.78) 0.05 (1.27) SEATING PLANE 15ⴗ 0 0.011 (0.28) 0.009 (0.23) NOTES 1. LEAD NO. 1 IDENTIFIED BY A DOT OR NOTCH. 2. PLASTIC LEADS WILL BE EITHER TIN PLATED OR SOLDER DIPPED IN ACCORDANCE WITH MIL-M-38510 REQUIREMENTS. 24-Lead Small Outline Package (R-24) 13 1 12 0.096 (2.44) 0.089 (2.26) PIN 1 0.01 (0.254) 0.006 (0.15) 0.414 (10.52) 0.398 (10.10) 24 0.299 (7.6) 0.291 (7.39) 0.608 (15.45) 0.596 (15.13) 0.05 (1.27) BSC 6ⴗ 0ⴗ SEATING 0.013 (0.32) PLANE 0.009 (0.23) 0.019 (0.49) 0.014 (0.35) 0.03 (0.76) 0.02 (0.51) 0.042 (1.067) 0.018 (0.447) NOTES 1. LEAD NO. 1 IDENTIFIED BY A DOT. 2. SOIC LEADS WILL BE EITHER TIN PLATED OR SOLDER DIPPED IN ACCORDANCE WITH MIL-M-38510 REQUIREMENTS. 24-Lead Shrink Small Outline Package (RS-24) 13 1 12 PIN 1 0.008 (0.203) 0.0256 (0.65) 0.002 (0.050) BSC PRINTED IN U.S.A. 24 0.212 (5.38) 0.205 (5.207) 0.311 (7.9) 0.301 (7.64) 0.328 (8.33) 0.318 (8.08) 0.07 (1.78) 0.066 (1.67) 8ⴗ 0.015 (0.38) 0ⴗ SEATING 0.010 (0.25) PLANE 0.009 (0.229) 0.005 (0.127) 0.037 (0.94) 0.022 (0.559) NOTES 1. LEAD NO. 1 IDENTIFIED BY A DOT. 2. LEADS WILL BE EITHER TIN PLATED OR SOLDER DIPPED IN ACCORDANCE WITH MIL-M-38510 REQUIREMENTS. –32– REV. B