AMS3132 3A Fast Transient Linear Regulator General Description Features The AMS3132 is a high performance linear regulator with very low dropout voltage and excellent transient response. It is designed to operate with wide input voltage range of 1.5 – 7Volts making it ideal for two step conversion while maintaining high efficiency for many power sensitive applications. The device is capable of supplying 3A of output current with a typical dropout voltage of 700mV at 3A. The product is available in either fixed or adjustable output voltage. The linear regulator has been optimized for noise sensitive applications. The device includes an optional enable pin for electrical on/off of the regulator. Forcing the enable pin to logic low shuts down the LDO and reduces the supply current to less than 1µA. The product includes complete short-circuit and thermal protection. The combination of these two internal protection circuits gives the device a comprehensive safety system to safe guard against extreme adverse operating conditions. The AMS3132 is available in a 5-pin surface mount TO263 package, and it is rated for -40°C to +125°C temperature range. • • • • • • • • • • • • • • • VIN range: 1.5 – 7V Fixed and Adjustable output voltage as low as 0.6V 3A maximum output current 700mV typical dropout voltage at 3A Low self noise Optional Power Good (PG) output Optional Enable (EN) pin for LDO on/off 125µA typical supply current PSRR >40dB at 10KHz Stable with Electrolytic, Tantalum or Ceramic capacitors Current Limit protection Over-Temperature Shutdown -40 to +125°C temperature range Available in a 5-pin surface mount TO-263 package RoHS & WEEE compliant Applications • • • • • • • Set-top Box DVD, Blue-ray DVD writers LCD TVs and LCD monitors Battery Powered Equipment Infotainment Wireless & RF Applications High Efficiency “Green” Laptops & notebook Typical Application 02/11/2010 www.advanced-monolithic.com 1 Phone (925) 443-0722 Fax (925) 443-0723 AMS3132 3A Fast Transient Linear Regulator Pin Description (TO-263 5-Pin Package) Pin # Symbol Description EN Enable pin. It controls the electrical on/off of the device. When connected to logic low, the device shuts off and consumes less than 1µA of current. Logic high will resume normal operation. PG Power Good pin. It is an open collector, active high output that indicates the status of the output voltage. When output voltage (VOUT) exceeds the PG trip threshold, the PG pin goes in to a high impedance state. When the device is out of regulation or shutdown, the PG pin is pulled low. A 10KΩ to 1MΩ resistor should be connected from PG to VOUT. 2 VIN Input supply Voltage. It powers the internal control circuitry and the internal power switch. Bypass VIN with at ceramic capacitor from this pin to ground. 3 GND Ground connection. 4 VOUT Output Voltage ADJ Provides feedback to error amplifier from the resistive divider that sets the output voltage. PG Power Good pin. It is an open collector, active high output that indicates the status of the output voltage. When output voltage (VOUT) exceeds the PG trip threshold, the PG pin goes in to a high impedance state. When the device is out of regulation or shutdown, the PG pin is pulled low. A 10KΩ to 1MΩ resistor should be connected from PG to VOUT. 1 5 Pin Configuration 02/11/2010 www.advanced-monolithic.com 2 Phone (925) 443-0722 Fax (925) 443-0723 AMS3132 3A Fast Transient Linear Regulator Absolute Maximum Ratings (1) Recommended Operating Conditions (2) Maximum Input Supply Voltage (VIN)………......…. ……-0.3V to 15V Enable Voltage (EN)…………..…..……………….……...-0.3V to 15V Power Good (PG).……………..…..……….……………...-0.3V to 15V Adjustable Voltage (ADJ)……………………….………… -0.3V to 3V Storage Temperature Range……………...................-65⁰C to 150⁰C Lead Temperature…………………..………….………..……… 260⁰C Junction Temperature………...………………..…………..…… 125⁰C Input Voltage…………………………………….………….. 1.5V to 7V Ambient Operating Temperature………….………… -40⁰C to 125⁰C Thermal Information TO263-5 θJA (3) …………………………....…………...….…...30⁰C/W Electrical Characteristics Unless otherwise noted: VIN=3.3V; VOUT=1.8V; CIN=10 µF ; COUT=22µF; -40⁰C≤TA=TJ≤85⁰C; TJ(Max.)= 125°C; Typical values are TA=25°C Parameter Output Voltage Accuracy Adjustable Voltage Adjustable pin bias current Maximum Output Current Load Regulation Line Regulation Supply Current Shutdown Current Current Limit Dropout Voltage Symbol VOUT VADJ IADJ_Bias IOUT_Max ISUP ISHDN ILIM VDO ΔVOUT/ΔVIN PSRR Output Noise Voltage Enable Threshold Low Enable Threshold High Input Enable Low Current Input Enable High Current en VEN(L) VEN(H) IEN(L) IEN(H) Conditions Adjustable VOUT only Adjustable VOUT only Min. -3 0.588 Typ. Max. Units 0.6 10 3 0.612 100 % V nA A % % mA µA A 3 IOUT= 0 – 3A VIN=3.0 – 7.0V; IOUT=100mA VIN=3.3V, Io=0A VIN=3.3V, VEN=0V 0.1 0.1 0.6 <1 6 IOUT=0.1A; VOUT=95% of VOUT(NOM) 60 IOUT=1A; VOUT=95% of VOUT(NOM) 220 IOUT=2A; VOUT=95% of VOUT(NOM) 420 IOUT=3A; VOUT=95% of VOUT(NOM) 700 F=10KHz Io=20mA 40 dB BW= 100Hz –100 KHz COUT = 22µF IOUT = 2.75A 125 µV(rms) Optional EN Pin present Optional EN Pin present VEN = 0V VEN = 1.5V 1.2 1.3 0 150 V V nA nA Power Good Low Threshold VPG % of VOUT PG ON / Opt. PG pin only Power Good High Threshold VPG % of VOUT PG OFF / Opt. PG pin only Power Good Output Low Voltage VPGL IPG_SINK = 500μA, Fault Condition 200 Power Good Leakage Current Thermal Shutdown Thermal Shutdown Hysteresis IPG TSD PG off, VPG = 12V 0.01 145 15 Notes: 1. 2. 3. TSD_HYS 1 3 mV 10 300 89 % 97 % 300 mV μA °C °C Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Junction to ambient thermal resistance with the TO-263 package tab soldered to a double side printed circuit board with 2.5 in2 of (1 oz.) copper area. With package soldering to 0.5in2 copper area over backside ground plane or internal power plane θJA can vary from 20°C/W to >40°C/W depending on mounting technique. The thermal resistance Junction to Case is 45⁰C/W. Total power dissipation for the switching regulator and the LDO should be taken in consideration when calculating the output current capability of each regulator. 02/11/2010 www.advanced-monolithic.com 3 Phone (925) 443-0722 Fax (925) 443-0723 A AMS3 3132 3A Fas st Transien nt Linear Regulator 1.804 Ou utput Voltage e Temperaturre Variation (Fixed Voltage Option) VO = 1.8V Adjustable Voltage (V) Output p Voltage g (V) ( ) Ty ypical Perfo ormance Characteris C stics (TA = 25°C 2 unless otherwise o sp pecified) 1.802 1.800 1.798 1.796 1.794 1.792 0.601 0.600 0.599 0.598 0.597 25 0 25 5 50 75 100 125 -2 Ambient Te emperature (ºC) ( Dro opout Voltag ge vs. Tempe erature 1.0 3A 0.8 0.1 0.0 -0.1 -0.2 0.6 2A 0.4 0.2 1A 0.0 3 4 5 6 Input Voltage (V) 7 -50 -2 25 0 25 5 50 75 100 125 Ambient Te emperature (°C) pout Voltage e vs. Output Current Drop Load d Regulation n 0.3 0.7 0.6 0.2 Voltage (V) Output Voltage Change (%) 0.602 -50 Line Regullation VOUT = 2.5V 0.2 0.603 -25 0 25 50 75 5 100 125 5 Ambient Temperature T e (ºC) Voltage (V) Output p Voltage g Error (%) ( ) -50 Ad djust (ADJ) Voltage V Temp perature Variation (Adjus stable Voltage Option) 0.1 0.0 -0.1 0.5 0.4 0.3 0.2 -0.2 0.1 -0.3 0.0 0.0 02/11/2010 0 0.1 1.0 Outputt Current (A) 10..0 VOUT = 2.5V O 0 www.ad dvanced-mono olithic.com 4 0.5 1 1.5 2 2.5 Output Current (A) 3 Phone (925)) 443-0722 Fax (925)) 443-0723 AMS3132 3A Fast Transient Linear Regulator IGND vs. Output Current VO=2.5V, VIN=3.3V Shutdown Current vs. Input Voltage 2.0 Ground Current (mA) Shutdown Current (µA) Typical Performance Characteristics (TA = 25°C unless otherwise specified) 1.5 125°C 1.0 25°C 0.5 ‐50°C 0.0 0 1 2 3 4 5 6 7 70 60 50 40 30 20 10 0 0.0 0.5 1.0 1.5 2.5 3.0 Output Current (A) Input Voltage (V) Load Transient 200mA to 2.8A, VOUT=2.5V,VIN=3.6V, CIN=COUT=22µF Enable Start-Up 2.5A, VOUT=2.5V,VIN=3.3V, CIN=COUT=22µF V OUT 1V /div V OUT 50mVac /div ISW OUT 1A /div Enable 1V/div 100 µsec/div 10 µsec/div 02/11/2010 2.0 www.advanced-monolithic.com 5 Phone (925) 443-0722 Fax (925) 443-0723 AMS3132 3A Fast Transient Linear Regulator Functional Block Diagram Figure 1: Block Diagram of AMS3132 5-Pin TO-263 Fixed Voltage with Power Good Option Figure 2: Block Diagram of AMS3132 5-Pin TO-263 Adjustable Voltage Option 02/11/2010 www.advanced-monolithic.com 6 Phone (925) 443-0722 Fax (925) 443-0723 AMS3132 3A Fast Transient Linear Regulator Functional Block Diagram Figure 3: Block Diagram of AMS3132 5-Pin TO-263 Adjustable Voltage with Power Good Option 02/11/2010 www.advanced-monolithic.com 7 Phone (925) 443-0722 Fax (925) 443-0723 AMS3132 3A Fast Transient Linear Regulator Device Summary The AMS3132 is a high voltage low drop out linear regulator with a current capability of up to 3A. The LDO has a recommended operating input voltage range of 1.5V to 7V with an output voltage as low as 0.6V and is stable with a wide range of ceramic, tantalum, and electrolytic output capacitors. Shutdown/Enable The Enable (on/off) input threshold voltage is 1.2V. When disabled the LDO quiescent current decreases to a typical value of <1µA. Fault Protection Short circuit and over-temperature shutdown disable the converter and LDO in the event of an overload condition. Over-temp shutdown disables the device when the junction temperature exceeds 145 ºC. The output current is internally limited to 6A typical. Input Capacitor An input bypass capacitor ranging from 1µF to 22µF is required. The capacitor should be placed as close as possible to the device and not be placed more than 1 inch from the LDO. Output Capacitor The output capacitor requirements range from the minimum value required to guarantee stability to larger values required to meet the extreme transient response requirements. Values range from 10 to 22µF X5R ceramic capacitors. Due to the extreme voltage coefficient of X5R ceramic capacitors, the voltage rating should be at least double the maximum applied voltage. Adjustable Version: Feedback Resistor Selection Choosing AMS3132 with adjustable output voltage option allows the user to select an output voltage by using an external resistor divider. AMS 3132 uses a 0.6V reference voltage at the positive terminal of the error amplifier. To set the output voltage a programming resistor from the adjust pin (ADJ) to ground must be selected (See Pg.1). A 10kΩ resistor is a good selection for a programming resistor R1. A higher value may result in an excessively sensitive feedback node while a lower value will draw more current and degrade the light load efficiency. The equation for selecting the voltage specific resistor is: R2= Vout Vref 02/11/2010 -1 ·R1 = 5V 0.6V -1 ·10kΩ=73.2kΩ Table 1: Adjustable Feedback Resistor values R2 (kΩ) Vout (V) (R1=10kΩ) 1.8 20.0 2.5 31.6 3.3 45.3 5.0 73.2 Power Good Version During operation, fault conditions can occur unexpectedly. Such conditions include input voltage dropout (low VIN), overheating, or overloading (excessive output current). If any of these conditions occurs, the PG pin will set an “error flag”. The PG pin, which is an open-collector output, will go LOW when VOUT is less than 95% or the specified output voltage. When the voltage at VOUT is greater than 95% of the specified output voltage, the PG pin is HIGH. A logic pull-up resistor of 10KΩ is recommended at this output. The pin can be left disconnected if unused. PCB Layout The following guidelines should be followed to insure proper layout. 1. VIN Capacitor. A low ESR ceramic bypass capacitor must be placed as close to the IC as possible. 2. Adjustable (ADJ) Feedback Resistors. The adjustable feedback resistors should be placed as close as possible the IC. Minimize the length of the trace from the feedback pin to the resistors. This is a high impedance node susceptible to interference from external RF noise sources 3. Ground. 4. For good thermal performance vias are required to couple the tab of the TO-263 package to the PCB ground plane. The via diameter should be 0.3mm to 0.33mm positioned on a 1.2mm grid. Output Power and Thermal Limits The AMS3132 junction temperature and current capability depends on the internal dissipation and the junction to case thermal resistance of the TO-263 exposed tab packages. Additionally, the tab paddle and PCB temperature will be elevated due to the total losses of the LDO and of other circuits mounted to the PCB. Tjmax=Pd·θjc+Tpcb+Tamb The internal losses contribute to the junction temperature rise above the paddle and PCB temperature. www.advanced-monolithic.com 8 Phone (925) 443-0722 Fax (925) 443-0723 AMS3132 3A Fast Transient Linear Regulator Figure 4: AMS3132 TO-263 5-Pin Evaluation Board Top Side Figure 5: AMS3132 TO-263 5-Pin Evaluation Board Bottom Side R3 *5 10k PG Enable/PG C7 *6 U1 1 Vin 2 3 C3 *1 470uF C4 *2 22uF C1 22uF EN/PG GND VIN ADJ/PG GND VOUT 6 R2 *3 5 4 AMS3132 C2 22uF R1 *4 10k Vout C5 *1 470uF C6 *2 22uF gnd gnd C1, C2 22uF X5R 1210 10V Ceramic Capaci tor *1. Optional Electrolyti c Capaci tor in place of Ceramic Capacitor *2. Optional Tantalum Capacitor in place of Ceramic Capacitor *3. 10k for AMS3132M-PG, Table 2 for AMS3132M and AMS3132-XX-PG *4. Not used for AMS3132M-PG, 10k for AMS3132M and AMS3132-XX-PG *5. Not used for AMS3132M-PG and AMS3132M, 10k for AMS3132-XX-PG *6. Optional Feedforward Capacitor (1nF to 10nF Typical) gnd Figure6: AMS3132 Universal Evaluation Board Schematic Component C1,C2 C3,C5,C4,C6 C7 R1 R2 R3 02/11/2010 Value Table 2: AMS3132 Universal Evaluation Board Bill of Material Manufacturer AMS3132 Version Manufacturer Part Number 22µF, 10V, X5R, 0805, Ceramic Optional Optional 10kΩ, 0.1W, 0603 1% Taiyo Yuden See table 2 Various 10kΩ, 0.1W, 0603 1% 10kΩ, 0.1W, 0603 1% Various Various Various any any any AMS3132M, or AMS3132-XX-PG AMS3132M, or AMS3132-XX-PG AMS3132M-PG AMS3132-XX-PG www.advanced-monolithic.com 9 LMK212BJ226MG-T CRCW060310K0FKEA CRCW0603xxKxFKEA CRCW060310K0FKEA CRCW060310K0FKEA Phone (925) 443-0722 Fax (925) 443-0723 AMS3132 3A Fast Transient Linear Regulator Ordering Information Device AMS3132M-XX-PG(1)(2)(3) TO-263 5-Pin AMS3132M (1)(2) TO-263 5-Pin AMS3132M-PG (1)(2) Package TO-263 5-Pin Notes: 1. Available in tape and reel only. A reel contains 2,500 devices. 2. Available in lead-free package only. Device is fully WEEE and RoHS compliant 3. Need to specify output voltage option ( ) Outline Drawing and Landing Pattern Package dimensions are inches (millimeters) unless otherwise noted. 0.390 -0.415 (9.906-10.541) 0.060 (1.524) TYP 0.165-0.180 (4.191-4.572) +0.008 -0.004 +0.203 ( 0.102 -0.102 0.004 0.330 -0.370 (8.382 -9.398) 0.199 -0.218 (5.05-5.54) 0.057-0.077 (1.447-1.955) 02/11/2010 0.032 (0.81) TYP 0.045-0.055 (1.143-1.397) 0.108 (2.74) TYP 0.013-0.023 (0.330-0.584) www.advanced-monolithic.com 10 ) 0.095-0.115 (2.413-2.921) 0.90-0.110 (2.29-2.79) M (DD5) AMS DRW#042192R1 Phone (925) 443-0722 Fax (925) 443-0723