THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. WWW.CONWIN.COM PRODUCT D ATA SHEET CRYSTAL CONTROLLED OSCILLATORS High Stability HCMOS OCXO CONNOR WINFIELD MODEL OFC5CE1AB FREQUENCY 10.000MHz 0722 DATE CODE CAL. FREQ. 10.000000 ABSOLUTE MAXIMUM RATINGS PARAMETER Storage Temperature Supply Voltage TABLE 1.0 UNITS MINIMUM -40 NOMINAL - MAXIMUM 85 UNITS °C (Vcc) -0.5 - 7 Vdc MINIMUM NOMINAL 10.000 12.800 MAXIMUM UNITS - MHz 2 OPERATING SPECIFICATIONS TABLE 2.0 PARAMETER Center Frequency - (Fo) Frequency Calibration Frequency Stability Aging: Daily Aging: First Year Aging: Short Term (1Sec.) Operating Temperature Range Supply Voltage Voltage Stability (+/-1%) Load Stability (+/-20%) Power Consumption: Turn On Power Consumption: Steady-State Start-Up Time Warm Up 2G Tip-over TDEV at 300 seconds TDEV at 40 seconds NOTE (Vcc) -2 -1 -30 0 5.00E-11 - 10 1 30 70 ppm ppb ppb/day ppb RMS °C 4.75 -0.5 -0.5 -100 - 5.00 5 - 5.25 0.5 0.5 2.75 1. 50 500 100 5 1 Vdc ppb ppb W W ms ppb ppb/G ns ns NOTE 1 2 3 4 5 6 7 8 8 9 10 OFC5CE1AB DESCRIPTION The Connor-Winfield OFC5CE1AB is a 5V Oven Controlled Crystal Oscillator (OCXO) with a HCMOS output. The OFC5CE1AB is designed for applications requiring high frequency stability over the commercial temperature range. 11 11 FEATURES HCMOS OUTPUT CHARACTERISTICS PARAMETER LOAD Voltage (High) (Low) Duty Cycle at 50% of Vcc Rise / Fall Time 10% to 90% Spurious Output SSB Phase Noise at 1Hz offset SSB Phase Noise at 10Hz offset SSB Phase Noise at 100Hz offset SSB Phase Noise at 1KHz offset TABLE 3.0 (Voh) (Vol) MINIMUM 12 4.2 45 - NOMINAL 15 50 - - SSB Phase Noise at 10KHz offset - MAXIMUM 18 0.4 55 5 -80 -90 -115 -130 -140 UNITS pF Vdc Vdc % nS dBc dBc/Hz dBc/Hz dBc/Hz dBc/Hz - -145 dBc/Hz NOTE 12 Fixed Frequency OCXO 5.0V Operation Frequency Stability: 10ppb Absolute Temperature Range HCMOS Output Logic RoHS 5/6 Compliant RESTABILIZATION TIME Off Time < 1 Hour < 6 Hours < 24 Hours 1 to 16 Days > 16 Days TABLE 4.0 NOTE 13 13 13 13 13 Restabilization Time < 2 Hours < 12 Hours < 48 Hours 48 Hours + ¼ Off Time < 6 Days PACKAGE CHARACTERISTICS Package TABLE 5.0 Metal package: solder sealed, grounded case, solder tinned pins. ENVIRONMNETAL CHARACTERISTICS TABLE 6.0 100G’s, 6mS, halfsine per MIL-STD-202F, Method 213B, Test Condition C 0.06” D.A. or 10G peak 10 to 500 Hz, per MIL-STD-202F, Method 204D, Test condition A See solder profile page 2. Shock Vibration Soldering Process Designed for Very High Stability Applications ORDERING INFORMATION OFC5CE1AB - 10.0M OCXO SERIES CENTER FREQUENCY Specifications subject to change without notice. DATA SHEET #: Cx092 PAGE 1 OF 2 REV: 00 DATE: 06/01/07 aCopyright 2007 Connor-Winfield all rights reserved. THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. WWW.CONWIN.COM PRODUCT D ATA SHEET CRYSTAL CONTROLLED OSCILLATORS Notes: 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) Labels will include the calibration frequency at the time of ship. Initial calibration @ 25C. Overall frequency stability, 0 to 70C Absolute. After ten days of continuous operation. Allen Variance: 1 second, 100 average. Frequency vs. change in supply voltage. Frequency vs. change in load. Vcc = 5.0Vdc. From Vcc=90% of final value. No more than 16 transitions at start-up before oscillator has started. Measured @ 0C, within 5 minutes, referenced one hour after turn-on. At time of delivery. HCMOS load. For a given off time, the time required to meet daily aging, short-term stability and TDEV requirements. Package Layout MODEL OFC5CE1AB FREQUENCY 10.000MHz DATE CODE 0722 CAL. FREQ. 10.000000 Pin Connections Test Circuit Solder Profile Temperature 225°C Ramp-Up Rate 3°C/second max. from 150°C to 225°C. 225°C tp Ramp-Down Rate 6°C/second max. 183°C 150°C 100°C 25°C 0 Time 60-120s Max. 10-30s 60-150s Max. 360 Sec. Max. Specifications subject to change without notice. DATA SHEET #: Cx092 PAGE 2 OF 2 REV: 00 DATE: 06/01/07 aCopyright 2007 Connor-Winfield all rights reserved.