FNP1500/1800 and FXP1500/1800 Front-Ends & FNR-3 and FXR-3 Power Shelves Data Sheet 1500 to 5400-Watt Front-End Power Solutions Features (1500 or 1800 Watts) Front-Ends are available using either a front-mounted AC receptacle (FNP models) or a rear-mounted AC connector (FXP models). I2C Management Software: All FNP/FXP front-ends can be controlled via Power-One's GUI-driven I2C Management software and an I2C-to-USB interface (P/N HZZ02002G). An 2 I C Programming Manual describes the complete range of parameters that can be programmed to the FNP and FXP1500/1800 front-ends. This manual is available by searching on "FNP1500" at www.power-one.com. • • • • • • • • • RoHS compliant for all six substances High density front-ends 15.2 to 18.3 W/in3 Wide input voltage range 85 to 264 VAC 12 V standby voltage, 1A per front-end Highly efficient topology reduces operating costs I2C interface status and control I2C voltage and current limit setting Analog output voltage setting Overtemperature, output overvoltage, and output overcurrent protection ORing circuits for true redundant operation: Vo1: ORing FETs; Vo2: ORing Diodes Status LEDs: AC OK, DC OK, and Fan Fail/Overtemperature Fail • • Applications • • • • Telecommunications Data communications Servers Distributed power FNR-3 Power Shelf FNR-3 and FXR-3 shelves provide up to 5400 watts in a 19" rack. (See the Rack section for power shelf details.) Description The FNP/FXP-1500/1800 are power-factor-corrected (PFC) front-ends which (depending on model type) provide a 12 VDC or 48 VDC (1500 or 1800 watt) output, and can be used in hot-swap redundant systems. Their very small dimensions allow configuration of up to three units in a 1U rack. The FNP front-ends have a front-mounted AC receptacle and the FXP front-ends have a rear-mounted AC connector. The highly-efficient thermal design with internal-fan cooling permits their use over wide temperature ranges and provides very-high reliability. Status information is provided with front panel LEDs, logic signals, and via an I2C management interface. In addition, the I2C bus can enable the power supply, set high fan speed, adjust the output voltage, and set the output current limit. The FNP and FXP-1500/1800's meet international safety standards and display the CE-Mark for the European Low Voltage Directive (LVD). Power-shelf solutions provide rectification, system management, and power distribution, while maintaining high reliability and offering flexibility for future expansion. The power shelves can be configured with up to three hot-swappable 1500 or 1800-watt AC-DC front-ends. DEC 12, 2006 revised to FEB 22, 2007 Page 1 of 15 www.power-one.com FNP1500/1800 and FXP1500/1800 Front-Ends & FNR-3 and FXR-3 Power Shelves Data Sheet Model Selection Model FNP1500-12G & FXP1500-12G FNP1500-48G & FXP1500-48G FNP1800-48G & FXP1800-48G 1 2 Output 1 Output 2 Input voltage VAC 1 auto selected Vo1 nom VDC Io1 max ADC Vo2 nom VDC Io2 max ADC 108 – 264 85 – 105 12 12 129 @ 11.64V 101.8 @ 11.78A 12 12 105 – 264 85 – 105 48 48 32.2 25.4 180 – 264 105 – 180 85 – 105 48 48 48 39.2 32.2 25.4 Rated power W Compatible 2 Shelf 1 1 1512 1212 FNR-3-12G & FXR-3-12G 12 12 1 1 1512 1212 FNR-3-48G & FXR-3-48G 12 12 12 1 1 1 1812 1512 1212 FNR-3-48G & FXR-3-48G The available output power is automatically adjusted depending on the input voltage. 1U standard racks are available from Power-One. See the Rack (Power Shelf) section of this data sheet for configurations and details. Absolute Maximum Ratings Stress in excess of the absolute maximum ratings may cause performance degradation, adversely effect long-term reliability, or cause permanent damage to the converter. Parameter Input voltage Conditions/Description Min Continuous Transient, 60 ms max. Operating ambient temperature Storage temperature Max Unit 264 300 VAC VAC Vi min-Vi max, Io nom, cooling by internal fan @ 100 % load @ 50 % load 0 0 50 70 °C °C Non-Operating -40 85 °C Environmental, Mechanical, & Reliability Specifications Parameter Altitude Relative humidity, non-condensing Temperature coefficient Shock Sinusoidal vibration Random vibration MTBF DEC 12, 2006 revised to FEB 22, 2007 Conditions/Description Min Nom Operating Non-Operating Max Unit 10 k 40 k ASL Ft. ASL Ft. Operating 10 90 % RH Storage 5 95 % RH 0 °C to 70 °C (after 15 min warm-up) 0.02 %/K IEC/EN 60068-2-27, 11 ms 40 gpk IEC/EN 60068-2-6 2-8 Hz 8-200 Hz 200-500 Hz 7.5 2 4 mil gpk gpk 10-2000 Hz 6.15 grms Calculated per Bellcore (SR-332, Issue 1): GB 25 °C GB 25 °C (FNP1500-12G) Demonstrated Page 2 of 15 230 TBD 250 kh kh kh www.power-one.com FNP1500/1800 and FXP1500/1800 Front-Ends & FNR-3 and FXR-3 Power Shelves Data Sheet Safety Specifications Maximum electric strength testing is performed in the factory according to EN 550116, IEC/EN 60950, and UL 60950. Input-to-output electric strength tests should not be repeated in the field. Power-One will not honor any warranty claims resulting from electric strength field tests. Parameter Conditions/description Agency approvals Insulation safety rating Input to case Input to output Output to case Electric strength test voltage 1 Min Nom Max Unit UL60950, (UL) CSA 60950 (cUL), EN 60950(TÜV), CE Mark for LVD Basic Reinforced Functional Input to case Input to output Output to case Output 1 to output 2 kVDC kVDC kVDC kVDC 2.12 1 4.2 0.5 0.1 Subassemblies are pre-tested with 4.2 kVDC in accordance with EN50116 and IEC/EN60950. EMC Specifications Parameter Description Criterion Electrostatic discharge Electromagnetic field Electrical fast transients/burst Surge Voltage dips and interruptions RF conducted immunity IEC/EN 61000-4-2, level 4 IEC/EN 61000-4-3, level 3 IEC/EN 61000-4-4, level 3 IEC/EN 61000-4-5, level 3 IEC/EN 61000-4-11 IEC/EN 61000-4-6 Emissions conducted Emissions radiated Harmonics Voltage fluctuation and flicker Voltage sag CISPR 22/EN 55022/EN 61204 CISPR 22/EN 55022/EN 61204 IEC/EN 61000-3-2 IEC/EN 61000-3-3 SEMI F47-0200 (High Line 230V) Performance criterion B Performance criterion A Performance criterion B Performance criterion B Performance criterion B or better 10 VAC, AM 80 %, 1 kHz Performance criterion A Class B Class A Class B Pass Pass Input Specifications Specification is valid for input voltage, load, and temperature ranges, unless otherwise stated. Parameter Conditions/description Min Nom Max Unit VAC Input voltage 85 230 264 Input frequency 47 50/60 63 Hz Turn-on input voltage Ramping up 79 - 85 VAC Turn-off input voltage Ramping down 70 - 78 VAC 50 Apk Inrush current limitation Hold-up time 115/230 VAC acc. ETS 300 132-1 < 100 ms After last AC line peak ,Vi = 230 VAC, Po nom 20 Vi nom, Io nom 0.95 Power factor Efficiency Vi = 230 VAC, Io nom, TC = 25 °C 89 1 ms W/VA 90 Max input current Input connector 1 % 20 Arms 16A – 20 A / 250 VAC; according to IEC320 C19 87% for FNP1500-12 Input Connector Description (FXP1500/1800) Protection Earth P1 Phase P2 L Neutral P3 N DEC 12, 2006 revised to FEB 22, 2007 PE Page 3 of 15 www.power-one.com FNP1500/1800 and FXP1500/1800 Front-Ends & FNR-3 and FXR-3 Power Shelves Data Sheet Output Specifications, 12Vout Models Specification is valid for input voltage, load, and temperature ranges, unless otherwise stated. Parameter Nominal output voltage Output voltage set point accuracy Output voltage trimming Conditions/Description Min Io = 64.5 A Vi = 230 VAC, Io1 = 65.5 A, TC = 25 °C (Factory setting) 2 Adjustable via I C (Vo1 set) Adjustable via Margin pin (R input) Nom 12.05 +0.42 VDC % Vo1 nom 7 6.2 12 13 Vo1 set VDC VDC 129.0 ADC ADC Io1 nom @ Vi =108 VAC – 264 VAC, Po 1.5 kW Io1 nom @ Vi = 85 VAC – 105 VAC, Po 1.2 kW 129.0 101.8 Current limit output 1 FNP1500-12G Io1 max @ Vi = 108 VAC – 264 VAC droop hiccup Io1 max @ Vi = 85 VAC – 105 VAC droop hiccup 147.4 120..2 Static line regulation output 1 Static load regulation output 1 (droop characteristic) FNP1500-12G Static load regulation output 2 (droop characteristic) Dynamic load regulation Current Share Io2 nom @ Vi = 85 VAC – 265 VAC, Po 12 W 1.0 Io2 max @ Vi = 85 VAC – 265 VAC 1.5 Vi min - Vi max, 50 % Io nom, Ta = 25 °C Vi = 230 V, 5 - 100 % Io nom Full load to no load [0..129 A] at Vo set = 12V dVo1 over the setting range [7 to 13V] VDC 12 FNP1500-12G Current limit output 2 Units 11.93 -0.42 Nominal current output 1 Nominal current output 2 Max 12 -0.5 11.64 -0.36 Full load to no load @ Vi = 85 VAC – 265 VAC - 5.58 12 ADC ADC 1.0 ADC ADC 0.5 % Vo nom 12.36 +0.36 mV/A VDC VDC 0.4 VDC Load change 50 % <─> 100 % Io nom, dIo/dt =1A/μs Voltage deviation (droop + over- or undershoot) FNP1500-12G FNP1500-12G -2 Max. recovery time to within 1% of Vo1 nom 2 % Vo nom 400 μs Difference in current between two units for Vo1 above 10 % load. FNP1500-12G Start-up time Output voltage ripple and noise (Filter 10nF/10µF) Remote sense DEC 12, 2006 revised to FEB 22, 2007 12.9 Time required for output within regulation after initial application of AC-input (Vi nom, Io nom) after removal of inhibit (Vi nom, Io nom) ADC 1.5 s ms Vi nom, Io nom, 20 MHz bandwidth Vo1 Vo2 120 120 mVpp mVpp Total compensation for cable losses 500 mV Page 4 of 15 100 www.power-one.com FNP1500/1800 and FXP1500/1800 Front-Ends & FNR-3 and FXR-3 Power Shelves Data Sheet Output Specifications, 48Vout Models Specification is valid for input voltage, load, and temperature ranges, unless otherwise stated. Parameter Conditions/Description Min Nom Max Units Nominal output voltage Vo1 Io = 16.1 A 48 VDC Nominal output voltage Vo2 Io = 0.5 A 12 VDC Output voltage set point accuracy Output voltage trimming 2 (via I C or with external resistor) Nominal current output 1 Current limit output 1 Vi = 230 VAC, Io1 =16.1 A, TC = 25 °C (47.8 - 48.2 VDC) -0.5 +0.5 % Vo1 nom Adjustable (44.16 to 51.84 VDC) -8 +8 % Vo1 nom FNP/FXP1500-48G Io1 nom @ Vi =105 VAC – 264 VAC, Po 1.5 kW Io1 nom @ Vi = 85 VAC – 105 VAC, Po 1.2 kW 32.2 25.4 FNP/FXP1800-48G Io1 nom @ Vi =180 VAC – 264 VAC, Po 1.8 kW Io1 nom @ Vi =105 VAC – 180 VAC, Po 1.5 kW Io1 nom @ Vi = 85 VAC – 105 VAC, Po 1.2 kW 39.2 32.2 25.4 FNP/FXP1500-48G Io1 max @ Vi = 105 VAC – 264 VAC Io1 max @ Vi = 85 VAC – 105 VAC droop hiccup droop hiccup 36.8 30 ADC ADC FNP/FXP1800-48G Io1 max @ Vi = 180 VAC – 264 VAC Io1 max @ Vi = 105 VAC – 180 VAC Io1 max @ Vi = 85 VAC – 105 VAC droop hiccup droop hiccup droop hiccup 43.8 36.8 30 ADC ADC ADC Nominal current output 2 Io2 nom @ Vi = 85 VAC – 264 VAC, Po 12 W 1.0 Current limit output 2 Io2 max @ Vi = 85 VAC – 264 VAC 1.5 Static line regulation output 1 FNP1500-48G FXP1500-48G Static load regulation output 1 (droop characteristic) FNP1800-48G FXP1800-48G Static load regulation output 2 (droop characteristic) Dynamic load regulation -0.5 Vi = 230 V, 5-100 % Io nom Vo : full load (32.2 ADC) to no load 46.54 Vi = 230 V, 5-100 % Io nom Vo : full load (32.2 ADC) to no load 39.2 1.0 ADC ADC ADC ADC ADC 0.5 % Vo nom 90.1 48 49.44 mV/A VDC 46.65 83.5 48 49.34 mV/A VDC Vi = 230 V, 5-100 % Io nom Vo : full load (32.2 ADC) to no load 45.91 90.1 48 49.44 mV/A VDC Vi = 230 V, 5-100 % Io nom Vo : full load (32.2 ADC) to no load 46.07 83.5 48 49.34 mV/A VDC Vi = 230 V, 5-100 % Io nom Vo : full load (32.2 ADC) to no load VDC 0.4 % Vo nom Load change 50 % <─> 100 % Io nom, dIo/dt =1 A/μs Voltage deviation (droop + over- or undershoot) FNP/FXP1500-48G -5 5 % Vo nom FNP/FXP1800-48G -5.7 5.7 % Vo nom 400 μs All models Current Share Vi min - Vi max, 50 % Io nom ADC ADC Max. recovery time to within 1 % of Vo1 nom Difference in current between two units for Vo1 above 10 % load. FNP1500-48G 3.2 ADC FXP1500-48G 5.7 ADC 8 ADC 1.5 s ms Vi nom, Io nom, 20 MHz bandwidth Vo1 Vo2 480 120 mVpp mVpp Total compensation for cable losses 500 mV FNP/FXP1800-48G Start-up time Output voltage ripple and noise (Filter 10 nF/10 µF) Remote sense DEC 12, 2006 revised to FEB 22, 2007 Time required for output within regulation after initial application of AC-input (Vi nom, Io nom) after removal of inhibit (Vi nom, Io nom) Page 5 of 15 100 www.power-one.com FNP1500/1800 and FXP1500/1800 Front-Ends & FNR-3 and FXR-3 Power Shelves Data Sheet Protection Parameter Conditions/Description Input fuse Min Not user accessible Inrush current limitation Max Unit With NTCs Output No-load -, short circuit - and overload proof Overvoltage protection latching Tracking Absolute 1 Overtemperature protection 1 Nom 25A, fast blow 115 Automatic power shutdown at TC 122 59.5 95 % Vo nom V °C Remove input voltage to reset. Control Specification is valid for input voltage, load, and temperature ranges, unless otherwise stated. Parameter Conditions/Description Status Indication LEDs: DC OK (green), AC OK (green); fan fail and overtemperature (amber) 2 I C digital bus Monitors alarm functions and sets parameters PS present pin Contact closure to logic ground ( internal pull-down resistor of 1 kΩ) PS remote shutdown / Inhibit pin TTL compatible signal, inhibited when open contact, high or at TTL logic “1” Signal referenced to logic return (LRTN) 2 Power supply OK (I C)* AC OK & DC OK & no overcurrent & no overtemperature & fans working 2 DC current fail (I C)* Overcurrent on Io1 Provides a warning that the input power has failed at least 5 ms before the output falls out of regulation (<90% Vo1 set). Open collector signal with 20 mA pull-down capability, referenced to logic return (LRTN). AC fail will go high or open during power fail condition and will go low when input is within the operating range. A Power Fail warning will turn off the green AC OK LED. Internal undervoltage and overvoltage supervision of Vo1. Open collector signal with 20 mA pull-down capability, referenced to logic return (LRTN). DC fail will go high or open if Vo1 is < 90% or > 110% of Vo1 set, measured in front of the ORing FETs. A green LED on the front panel indicates normal operation. The LED will flash if in parallel operation Vo1 is ok, but the unit is disabled. AC fail / Power down warning 2 (I C & OC)* DC fail / Output voltage fault 2 (I C & OC)* 2 2 1 Temperature warning (I C & OC) 2 1 2 1 DC voltage monitoring (I C) Monitors the voltage Vo1 at the output connector. Accuracy ± 0.45 V over setting range, temperature and load. DC current monitoring (I C) Monitors the output current Io1 : Accuracy ± 0.4A over the load range. DC voltage trimming 2 1 (I C or external resistor) Output voltage trimming Vo1: ± 8 % of Vo set 2 Setting accuracy over I C: ± 50mV at Vo nom, ± 150 mV over setting range 2 Fan speed control (I C) 2 Fan OK (I C & OC) 1 1 Two fan speed levels automatically set depending on the internal temperature. The fan speed can be set to full speed or automatic control. Indicates if the fans are operating or have failed. Overcurrent signal which can be used for synchronous startup of units in parallel or to recover from an overload condition. (See application note). Synch. startup pin 1 I C critical temperature warning: Indicates that the operating temperature has reached [Tshut-down – 10K] 2 I C & OC overtemperature warning: Indicates if the unit is in overtemperature shutdown. Open collector signal with 20 mA pull-down capability, referenced to logic return (LRTN). The OC-output will go low 100 ms before an overtemperature condition shuts down the unit. An amber LED on the front panel indicates overtemperature or fan fail. 2 Provided over the I C interface or as an open collector signal on the output connector (OC). 2 2 For detailed Information on I C, please see document “FNP1500-I2C-controlling.pdf” or use the Power-One I C Management Interface document. DEC 12, 2006 revised to FEB 22, 2007 Page 6 of 15 www.power-one.com FNP1500/1800 and FXP1500/1800 Front-Ends & FNR-3 and FXR-3 Power Shelves Data Sheet Output Connector Pinning and Signal Specification (12V Models) Output Connector Description Overtemperature / Fan Fail AC Fail / Power down warning Power Supply Present DC Fail / Output voltage fault Internal ground ADDR0, I2C address bus ADDR1, I2C address bus ADDR2, I2C address bus ADDR3, I2C address bus ADDR4, I2C address bus Pin Location U1 U2 U3 U4 U5 T1 T2 T3 T4 T5 Type Low level High level U max I max OC-output, protected by 16 V Zener diode and a 10 Ω resistor in series, referenced to logic GND < 0.4 V @ 20 mA Pull up 15 V 20 mA < 0.4 V @ 20 mA Pull up Open Resistor (1 kΩ) connected to logic GND Pull up OC-output, protected by 16 V Zener diode and a < 0.4 V @ 20 mA Pull up 10 Ω resistor in series, referenced to logic GND Internal ground (Vo1– line before the output filter). Do not connect the internal grounds in systems with several units. 15 V 20 mA 10 V 10 mA 15 V 20 mA - OC-output, protected by 16 V Zener diode and a 10 Ω resistor in series, referenced to logic GND DIP switch or wire to internal ground, Internally pull up to 5V (10 kΩ). DIP switch or wire to internal ground, Internally pull up to 5V (10 kΩ). DIP switch or wire to internal ground, Internally pull up to 5V (10 kΩ). DIP switch or wire to internal ground, Internally pull up to 5V (10 kΩ). DIP switch or wire to internal ground, Internally pull up to 5V (10 kΩ). Switch closed Switch open Switch closed Switch open Switch closed Switch open Switch closed Switch open Switch closed Switch open 2 I C compatible signal referenced to logic GND I2C compatible signal referenced to logic GND 5V 5V 5V 5V 5V - DATA, I2C data line S1 CLOCK, I2C clock line S2 Vo2 + output S3 Auxiliary power pin, insulated from main output - - Vo2 – output S4 Auxiliary ground pin, insulated from main output - - - - Logic ground S5 Internally connected over 10 Ω to Auxiliary GND. Wire separately form Auxiliary - and main output 2 GND to minimize noise on signals and I C. Leave open if not used. Output inhibit R1 < 0.8 V > 2.0 V 10 V 3.5 mA V sense + R2 V sense - R3 Output margin R4 PS active when pulled low (DC-DC stage off when left open) Referenced to logic GND Open or connected to Vo1+ at the load (Internally connected to Vo1+ over 100 Ω) Open or connected to Vo1- at the load (Internally connected to Vo1- over 100 Ω) Open or connected over resistor to internal ground. Do not connect the margin pins in systems with several units. - dU < 3 Vpp 30 mA dU < 3 Vpp 30 mA 3 VDC - Synch. Startup R5 Open or connected to synch startup circuit, referenced to Vo1 - at the output connector - 12V 3mA - - - - Vo1 + output Vo1 – output P2, P4, P6, P8, P10, P12 P1, P3, P5, P7, P9, P11 DEC 12, 2006 revised to FEB 22, 2007 Main output + pins Main output – pins Page 7 of 15 5 V or 3.3 V logic 5 V or 3.3 V logic - www.power-one.com FNP1500/1800 and FXP1500/1800 Front-Ends & FNR-3 and FXR-3 Power Shelves Data Sheet Output Connector Pinning and Signal Specification (48V Models) Output Connector Description Overtemperature / Fan Fail AC Fail / Power down warning Pin Location U1 U2 Power Supply Present U3 DC Fail / Output voltage fault U4 Internal ground U5 Type Low level High level V max I max OC-output, protected by 16 V Zener diode and a 10 Ω resistor in series, referenced to logic GND OC-output, protected by 16 V Zener diode and a 10 Ω resistor in series, referenced to logic GND <0.4 V @ 20 mA Pull up <0.4 V @ 20 mA Pull up Open Pull up <0.4 V @ 20 mA Pull up - 15 V 20 mA 15 V 20 mA 10 V 10 mA 15 V 20 mA - Resistor (1 kΩ) connected to logic GND OC-output, protected by 16 V Zener diode and a 10 Ω resistor in series, referenced to logic GND Internal ground (Vo1– line before the output filter). Do not connect the internal grounds in systems with several units. 2 T1 DIP switch or wire to internal ground, Internally pull up to 5V (10 kΩ). Switch closed Switch open 5V - 2 T2 DIP switch or wire to internal ground, Internally pull up to 5V (10 kΩ). Switch closed Switch open 5V - 2 T3 DIP switch or wire to internal ground, Internally pull up to 5V (10 kΩ). Switch closed Switch open 5V - 2 T4 DIP switch or wire to internal ground, Internally pull up to 5V (10 kΩ). Switch closed Switch open 5V - 2 T5 DIP switch or wire to internal ground, Internally pull up to 5V (10 kΩ). Switch closed Switch open 5V - DATA, I C data line S1 I C compatible signal referenced to logic GND CLOCK, I C clock line 2 S2 I C compatible signal referenced to logic GND 5 V or 3.3 V logic Auxiliary power +12 V S3 Vo2+ output, insulated from main output - - Auxiliary power ground S4 Vo2 - output, insulated from main output - - - - Logic ground S5 Internally connected over 10 Ω to Auxiliary GND. Wire separately form Auxiliary - and main output GND 2 to minimize noise on signals and I C. Leave open if not used. Output inhibit R1 PS active when pulled low (DC-DC stage off when left open) Referenced to logic GND <0.8 V >2.0 V 10 V 3.5 mA V sense + R2 Open or connected to Vo1+ at the load (Internally connected to Vo1+ over 100 Ω) dV < 3 Vpp 30 mA V sense - R3 Open or connected to Vo1- at the load (Internally connected to Vo1- over 100 Ω) Open or connected to internal ground (+8 % Vo1) or V sense+ (-8 % Vo1) Do not connect the margin pins in systems with several units. dV < 3 Vpp 30 mA - 60V - ADDR0, I C address bus ADDR1, I C address bus ADDR2, I C address bus ADDR3, I C address bus ADDR4, I C address bus 2 2 5 V or 3.3 V logic 2 - Output margin R4 Synch. Startup R5 Open or connected to synch startup circuit, referenced to Vo1 - at the output connector - 12V 2mA P1, P3, P5 Main output – pins - - Main output + pins - - Vo1 Vo1 + P2, P4, P6 Fulcrum: The handle has been designed to allow easy plug-in and -out in a rack system. The handle (lever) fits into a counter piece (fulcrum) which is fixed to the bottom of the rack. During the plug, the fulcrum holds the unit down and guides it towards the output connector. The Power-One part number of the fulcrum and its associated mounting accessories is: HZZ01223. DEC 12, 2006 revised to FEB 22, 2007 Page 8 of 15 www.power-one.com FNP1500/1800 and FXP1500/1800 Front-Ends & FNR-3 and FXR-3 Power Shelves Data Sheet Mechanical Data FNP1500/1800 Mechanical Data (H, W, D) 1.6” (40.6 mm) x 5.6” (142.2 mm) x 11” (279.4 mm) FXP1500/1800 Mechanical Data (H, W, D) 1.6” (40.6 mm) x 5.6” (142.2 mm) x 12” (304.8 mm) Note: FNP1500/1800's have only 11" (279.4 mm) depth Output Connector Descriptions (12V Models) Rear View Connector: FCI (51732-026 LF) Female ledge connector: Manufacturer: FCI Right Angle type: Part No. FCI (manufacturer): 51762-11202000AA LF; Power-One Part No.: ZES260-G Vertical type: Part No. FCI (manufacturer): 51742-11202000AA LF; Power-One Part No.: ZES282-G Information on availability of FCI connectors under http://www.stkcheck.com/evs/fcielectronics/fcisearch.asp IEC AC power cord with C19 connector VDE 16A: Interpower Components Ltd. 70009110250 IEC AC power cord with C19 connector UL 20A: Interpower Components Ltd. 70025110250 DEC 12, 2006 revised to FEB 22, 2007 Page 9 of 15 www.power-one.com FNP1500/1800 and FXP1500/1800 Front-Ends & FNR-3 and FXR-3 Power Shelves Data Sheet FNP1500/1800 (48V Model) Output Connector Descriptions Rear View Connector: FCI (51732-020 LF) Female ledge connector: Manufacturer: FCI Right Angle type: Part No. FCI (manufacturer): 51762-106020000AA LF; Power-One Part No.: ZES258-G Vertical type: Part No. FCI (manufacturer): 51742-106020000AA LF; Power-One Part No.: ZES271-G Locate information on availability of FCI connectors at http://www.stkcheck.com/evs/fcielectronics/fcisearch.asp FXP1500/1800 (48V Model) Input and Output Connector Descriptions Rear View Female ledge connector: Output connector Part No.: Output connector Part No.: Input connector Part No.: Input connector Part No.: Output con.: FCI (51732-020 LF) Input con.: FCI (51939-126 LF) Manufacturer: FCI 51762-106020000AA LF (Horizontal) 51742-106020000AA LF (Vertical) 51915-056LF (Horizontal) 51940-099LF (Vertical) Locate information on availability of FCI connectors at http://www.stkcheck.com/evs/fcielectronics/fcisearch.asp Paralleling Front-Ends: For parallel use in minimal configuration systems, only the inhibit pins must be shorted to logic GND. All other pins can be left open. The power supplies will share the output current automatically (droop current share). For parallel applications without I2C bus, but the use of all other features, it is recommended to connect all logic GND’s on a backplane together, to connect all Vo2 -, all V o2 + and to leave the internal GND’s open. The sense wires can be left open or connected to a common load point, the synch-start pin can be left open or connected to a synch-start circuit, the inhibit pins can be connected together or used individually. All I2C signals (T1-T5, S1, and S2) can be left open. Use of a small foil capacitor > 3µF directly at the power outputs of each unit is recommended in order to prevent voltage drops at the hot plug. For additional information on paralleling see the following Rack (Power Shelf) section. DEC 12, 2006 revised to FEB 22, 2007 Page 10 of 15 www.power-one.com FNP1500/1800 and FXP1500/1800 Front-Ends & FNR-3 and FXR-3 Power Shelves Data Sheet Racks (FNR-3-12G, FXR-3-12G, FNR-3-48G, and FXR-3-48G Power Shelves) Each rack (power shelf) is 1U high with backplane and designed for up to three front-end models in parallel or in n+1 operation. Each power shelf has: • Massive copper bus bars for low-loss current distribution. • Output terminals with two M4-screws on each power tab. • Two fast-on contacts for system earthing. • Address coding over five pole DIP switch on each unit, 37-pin D-Sub connector with I2C-lines, monitoring signals and support functions. • Provides a start-up synchronization circuit and EMV filters. FNR-3-12G and FNR-3-48G Power Shelf Front View FXR-3-12G and FXR-3-48G Power Shelf Front View Overall Mechanical Dimensions (FNR-3-12G and FNR-3-48G Power Shelves) FNR-3 Mechanical Data (W, H, D) 17.7” (449.6 mm) x 1.7” (43.1 mm) x 13” (330.2 mm) FXR-3 Mechanical Data (W, H, D) 17.7” (449.6 mm) x 1.7” (43.1 mm) x 14” (355.6 mm) DEC 12, 2006 revised to FEB 22, 2007 Page 11 of 15 www.power-one.com FNP1500/1800 and FXP1500/1800 Front-Ends & FNR-3 and FXR-3 Power Shelves Data Sheet Output Connector Descriptions (FNR-3-12G and FNR-3-48G) A B D C F E G H I Location Description A 5-Bit DIP switch for I2C addressing of PSU 1 B Earth connection C Earth connection D Earth connection E Output 1 minus F Output 1 plus G 5-Bit DIP switch for I2C addressing of PSU 2 H 37-pin SUB-D connector, controlling and auxiliary power (output 2) I 5-Bit DIP switch for I2C addressing of PSU 3 Output Connector Descriptions (FXR-3-12G and FXR-3-48G) PE3 L3 A Location B N3 C D E F PE2 PE1 L2 N2 L1 N1 G H I J Description A Earth connection B 5-bit DIP switch for I2C addressing of PSU #3 C Mains connector of PSU #3 D Output 1 Minus E Output 1 Plus F 5-bit DIP switch for I2C addressing of PSU #2 G Mains connector of PSU #2 H 37-pin SUB-D connector, control, sense, check and Auxiliary power (Output 2) I 5-bit DIP switch for I2C addressing of PSU #1 J Mains connector of PSU #1 DEC 12, 2006 revised to FEB 22, 2007 Page 12 of 15 www.power-one.com FNP1500/1800 and FXP1500/1800 Front-Ends & FNR-3 and FXR-3 Power Shelves Data Sheet Mechanical Data (FNR-3-12G and FNR-3-48G Power Shelves) (To Be Supplied) Mechanical Data (FXR-3-12G and FXR-3-48G Power Shelves) DEC 12, 2006 revised to FEB 22, 2007 Page 13 of 15 www.power-one.com FNP1500/1800 and FXP1500/1800 Front-Ends & FNR-3 and FXR-3 Power Shelves Data Sheet Accessories: Center Angular Brackets are set in the middle for shelf mounting: Center Angular Bracket sets can be ordered: Power-One part no.: HZZ01222 Note: Each Center Angular Bracket set contains 2 brackets and 8 screws. Fulcrums: Individual fulcrum sets can be also ordered: Power-One part no.: HZZ01223. Note: Each HZZ01223 set contain 2 fulcrums, 2 supports, and mounting accessories. DEC 12, 2006 revised to FEB 22, 2007 Page 14 of 15 www.power-one.com FNP1500/1800 and FXP1500/1800 Front-Ends & FNR-3 and FXR-3 Power Shelves Data Sheet I2C to USB Interface HZZ02002G: I2C <to>USB Interface An I2C to RS232 Interface can be ordered from Power-One. The interface part number to order is HZZ02002G. All FNP/FXP front-ends can be controlled via Power-One's GUI-driven I2C Management software and the I2C-to-USB interface. 2 An I C Programming Manual describes the complete range of parameters that can be programmed to the FNP and FXP1500/1800 front-ends. This manual is available by searching on "FNP1500" at www.power-one.com. NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective divisional president of Power-One, Inc. TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice. DEC 12, 2006 revised to FEB 22, 2007 Page 15 of 15 www.power-one.com