TI LM27342SDX/NOPB Lm27341/lm27342/lm27341-q1/lm27342-q1 2 mhz 1.5a/2a wide input range step-down dc-dc regulator with frequency synchronization Datasheet

LM27341, LM27342, LM27341-Q1, LM27342-Q1
www.ti.com
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
LM27341/LM27342/LM27341-Q1/LM27342-Q1 2 MHz 1.5A/2A Wide Input Range Step-Down
DC-DC Regulator with Frequency Synchronization
Check for Samples: LM27341, LM27342, LM27341-Q1, LM27342-Q1
FEATURES
DESCRIPTION
•
The LM27341 and LM27342 regulators are
monolithic, high frequency, PWM step-down DC-DC
converters in 10-pin SON and 10-pin MSOPPowerPad packages. They contain all the active
functions to provide local DC-DC conversion with fast
transient response and accurate regulation in the
smallest possible PCB area.
1
2
•
•
•
•
•
•
•
•
•
•
•
•
Space Saving 3 x 3 mm 10-Pin SON and
MSOP-PowerPad Packages
Wide Input Voltage Range: 3V to 20V
Wide Output Voltage Range: 1V to 18V
LM27341 Delivers 1.5A Maximum Output
Current
LM27342 Delivers 2A Maximum Output Current
High Switching Frequency: 2 MHz
Frequency Synchronization: 1.00 MHz < fSW <
2.35 MHz
150 mΩ NMOS Switch with Internal Bootstrap
Supply
70 nA Shutdown Current
Internal Voltage Reference Accuracy of 1%
Peak Current-Mode, PWM Operation
Thermal Shutdown
LM27341-Q1 and LM27342-Q1 are AEC-Q100
Grade 1 Qualified and are Manufactured on an
Automotive Grade Flow
APPLICATIONS
•
•
•
•
•
•
•
Local 12V to Vcore Step-Down Converters
Radio Power Supply
Core Power in HDDs
Set-Top Boxes
Automotive
USB Powered Devices
DSL Modems
With a minimum of external components the
LM27341 and LM27342 are easy to use. The ability
to drive 1.5A or 2A loads respectively, with an internal
150 mΩ NMOS switch results in the best power
density available. The world-class control circuitry
allows for on-times as low as 65 ns, thus supporting
exceptionally high frequency conversion. Switching
frequency is internally set to 2 MHz and
synchronizable from 1 to 2.35 MHz, which allows the
use of extremely small surface mount inductors and
chip capacitors. Even though the operating frequency
is very high, efficiencies up to 90% are easy to
achieve. External shutdown is included featuring an
ultra-low shutdown current of 70 nA. The LM27341
and LM27342 utilize peak current-mode control and
internal compensation to provide high-performance
regulation over a wide range of operating conditions.
Additional features include internal soft-start circuitry
to reduce inrush current, pulse-by-pulse current limit,
thermal
shutdown,
and
output
over-voltage
protection.
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2008–2013, Texas Instruments Incorporated
LM27341, LM27342, LM27341-Q1, LM27342-Q1
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
www.ti.com
Typical Application Circuit
VIN
PVIN
BOOST
C2
AVIN
L1
C1
VOUT
SW
C3
D1
LM27341/2
ON
EN
OFF
R1
SYNC
CLK
FB
GND / DAP
R2
Figure 1.
Figure 2. Efficiency vs Load Current
VOUT = 5V, fsw = 2 MHz
Connection Diagram
SW
1
10
PVIN
SW
1
10
PVIN
SW
2
9
PVIN
SW
2
9
PVIN
BOOST
3
8
AVIN
BOOST
3
8
AVIN
EN
4
7
GND
EN
4
7
GND
SYNC
5
6
FB
SYNC
5
6
FB
DAP
Figure 3. 10-Lead SON (Top View)
See DSC0010A Package
DAP
Figure 4. 10-Lead MSOP-PowerPad (Top View)
See DGQ0010A Package
PIN DESCRIPTIONS
2
Pin
Name
1, 2
SW
3
BOOST
4
EN
5
SYNC
Function
Output switch. Connects to the inductor, catch diode, and bootstrap capacitor.
Boost voltage that drives the internal NMOS control switch. A bootstrap capacitor is connected between the
BOOST and SW pins.
Enable control input. Logic high enables operation. Do not allow this pin to float or be greater than VIN + 0.3V.
Frequency synchronization input. Drive this pin with an external clock or pulse train. Ground it to use the
internal clock.
6
FB
7
GND
Feedback pin. Connect FB to the external resistor divider to set output voltage.
Signal and Power Ground pin. Place the bottom resistor of the feedback network as close as possible to this
pin for accurate regulation.
8
AVIN
Supply voltage for the control circuitry.
9, 10
PVIN
Supply voltage for output power stage. Connect a bypass capacitor to this pin.
DAP
GND
Signal / Power Ground and thermal connection. Tie this directly to GND (pin 7). See Application Information
regarding optimum thermal layout.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
LM27341, LM27342, LM27341-Q1, LM27342-Q1
www.ti.com
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
Absolute Maximum Ratings (1) (2)
AVIN, PVIN
-0.5V to 24V
SW Voltage
-0.5V to 24V
Boost Voltage
-0.5V to 28V
Boost to SW Voltage
-0.5V to 6.0V
FB Voltage
-0.5V to 3.0V
SYNC Voltage
-0.5V to 6.0V
EN Voltage
-0.5V to (VIN + 0.3V)
−65°C to +150°C
Storage Temperature Range
Junction Temperature
150°C
ESD Susceptibility (3)
Soldering Information
(1)
(2)
(3)
2kV
Infrared Reflow (5sec)
260°C
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur, including inoperability and degradation of
device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or
other conditions beyond those indicated in the recommended Operating Ratings is not implied. The recommended Operating Ratings
indicate conditions at which the device is functional and should not be operated beyond such conditions.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
Human body model, 1.5 kΩ in series with 100 pF.
Operating Ratings (1)
AVIN, PVIN
3V to 20V
SW Voltage
-0.5V to 20V
Boost Voltage
-0.5V to 24V
Boost to SW Voltage
3.0V to 5.5V
−40°C to +125°C
Junction Temperature Range
Thermal Resistance (θJA) SON (2)
33°C/W
Thermal Resistance (θJA) MSOP-PowerPad (2)
45°C/W
(1)
(2)
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur, including inoperability and degradation of
device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or
other conditions beyond those indicated in the recommended Operating Ratings is not implied. The recommended Operating Ratings
indicate conditions at which the device is functional and should not be operated beyond such conditions.
Thermal shutdown will occur if the junction temperature exceeds 165°C. The maximum power dissipation is a function of TJ(MAX) , θJA
and TA . The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX) – TA)/θJA . All numbers apply for
packages soldered directly onto a 3” x 3” PC board with 2oz. copper on 4 layers in still air.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
3
LM27341, LM27342, LM27341-Q1, LM27342-Q1
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
www.ti.com
Electrical Characteristics
Specifications with standard typeface are for TJ = 25°C, and those in boldface type apply over the full Operating
Temperature Range (TJ = -40°C to 125°C). VIN = 12V, and VBOOST - VSW = 4.3V unless otherwise specified. Datasheet
min/max specification limits are ensured by design, test, or statistical analysis.
Symbol
Parameter
Conditions
Min
Typ
Max
TJ = 0°C to 85°C
0.990
1.0
1.010
TJ = -40°C to 125°C
0.984
1.0
1.014
Units
SYSTEM PARAMETERS
VFB
ΔVFB/ΔVIN
IFB
Feedback Voltage
Feedback Voltage Line
Regulation
VIN = 3V to 20V
0.003
Feedback Input Bias Current
OVP
UVLO
SS
20
Over Voltage Protection, VFB at
which PWM Halts.
IQ
IBOOST
%/V
100
1.13
nA
V
Undervoltage Lockout
VIN Rising until VSW is Switching
2.60
2.75
2.90
UVLO Hysteresis
VIN Falling from UVLO
0.30
0.47
0.6
0.5
1
1.5
Soft Start Time
V
V
ms
Quiescent Current, IQ = IQ_AVIN +
IQ_PVIN
VFB = 1.1 (not switching)
2.4
mA
Quiescent Current, IQ = IQ_AVIN +
IQ_PVIN
VEN = 0V (shutdown)
70
nA
fSW= 2 MHz
8.2
10
fSW= 1 MHz
4.4
6
2
2.3
Boost Pin Current
mA
OSCILLATOR
fSW
Switching Frequency
VFB_FOLD
FB Pin Voltage where SYNC input
is overridden.
fFOLD_MIN
Frequency Foldback Minimum
SYNC = GND
1.75
0.53
VFB = 0V
220
MHz
V
250
kHz
2.35
MHz
LOGIC INPUTS (EN, SYNC)
fSYNC
SYNC Frequency Range
1
VIL
EN, SYNC Logic low threshold
Logic Falling Edge
VIH
EN, SYNC Logic high threshold
Logic Rising Edge
0.4
1.8
V
tSYNC_HIGH
SYNC, Time Required above VIH
to Ensure a Logical High.
100
ns
tSYNC_LOW
SYNC, Time Required below VIL
to Ensure a Logical Low.
100
ns
ISYNC
IEN
SYNC Pin Current
Enable Pin Current
VSYNC < 5V
20
VEN = 3V
6
15
nA
VIN = VEN = 20V
50
100
150
320
µA
INTERNAL MOSFET
RDS(ON)
ICL
Switch ON Resistance
Switch Current Limit
DMAX
Maximum Duty Cycle
LM27342
2.5
4.0
LM27341
2.0
3.7
SYNC = GND
85
mΩ
A
93
%
tMIN
Minimum on time
65
ns
ISW
Switch Leakage Current
40
nA
Boost LDO Output Voltage
3.9
V
BOOST LDO
VLDO
THERMAL
TSHDN
4
Thermal Shutdown Temperature
Junction temperature rising
165
°C
Thermal Shutdown Hysteresis
Junction temperature falling
15
°C
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
LM27341, LM27342, LM27341-Q1, LM27342-Q1
www.ti.com
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
Typical Performance Characteristics
All curves taken at VIN = 12V, VBOOST - VSW = 4.3V and TA = 25°C, unless specified otherwise.
Efficiency vs Load Current
VOUT = 5V, fSW = 2 MHz
Refer to Figure 40
Load Transient
VOUT = 5V, IOUT = 100 mA - 2A @ slewrate = 2A / µs
Refer to Figure 40
Figure 5.
Figure 6.
Efficiency vs Load Current
VOUT = 3.3V, fSW = 2 MHz
Refer to Figure 46
Load Transient
VOUT = 3.3V, IOUT = 100 mA - 2A @ slewrate = 2A / µs
Refer to Figure 46
Figure 7.
Figure 8.
Efficiency vs Load Current
VOUT = 1.8V, fSW = 2 MHz
Refer to Figure 55
Load Transient
VOUT = 1.8V, IOUT = 100 mA - 2A @ slewrate = 2A / µs
Refer to Figure 55
Figure 9.
Figure 10.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
5
LM27341, LM27342, LM27341-Q1, LM27342-Q1
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics (continued)
All curves taken at VIN = 12V, VBOOST - VSW = 4.3V and TA = 25°C, unless specified otherwise.
6
Line Transient
VIN = 10 to 15V, VOUT = 3.3V, no CFF
Refer to Figure 49
Line Transient
VIN = 10 to 15V, VOUT = 3.3V
Refer to Figure 46
Figure 11.
Figure 12.
Short Circuit
Short Circuit Release
Figure 13.
Figure 14.
Soft Start
Soft Start with EN Tied to VIN
Figure 15.
Figure 16.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
LM27341, LM27342, LM27341-Q1, LM27342-Q1
www.ti.com
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
Typical Performance Characteristics (continued)
All curves taken at VIN = 12V, VBOOST - VSW = 4.3V and TA = 25°C, unless specified otherwise.
VIN = 12V, VOUT = 5 V, L = 2.2 µH, COUT = 44 µF Iout =1A
Refer to Figure 40
VIN = 12V, VOUT = 3.3V, L = 1.5 µH COUT = 44 µF Iout =1A
Refer to Figure 46
Figure 17.
Figure 18.
VIN = 5V, VOUT = 1.8V, L = 1.0 µH COUT = 44 µF Iout =1A
Refer to Figure 55
VIN = 5V, VOUT = 1.2V, L = 0.56 µH COUT = 68 µF Iout =1A
Refer to Figure 61
Figure 19.
Figure 20.
Sync Functionality
Loss of Synchronization
Figure 21.
Figure 22.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
7
LM27341, LM27342, LM27341-Q1, LM27342-Q1
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics (continued)
All curves taken at VIN = 12V, VBOOST - VSW = 4.3V and TA = 25°C, unless specified otherwise.
8
Oscillator Frequency vs Temperature
VSYNC = GND, fSW = 2 MHz
Oscillator Frequency vs VFB
Figure 23.
Figure 24.
VFB vs Temperature
VFB vs VIN
Figure 25.
Figure 26.
Current Limit vs Temperature
VIN = 12V
RDSON vs Temperature
Figure 27.
Figure 28.
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
LM27341, LM27342, LM27341-Q1, LM27342-Q1
www.ti.com
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
Typical Performance Characteristics (continued)
All curves taken at VIN = 12V, VBOOST - VSW = 4.3V and TA = 25°C, unless specified otherwise.
IQ (Shutdown) vs Temperature
IQ = IAVIN + IPVIN
IEN vs VEN
Figure 29.
Figure 30.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
9
LM27341, LM27342, LM27341-Q1, LM27342-Q1
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
www.ti.com
Block Diagram
BOOST
D2
LDO
PVIN
C2
Switch
0.15:
RSENSE
L
SW
VOUT
iL
+
AVIN
D1
Driver
Current Sense
Amplifier
C3
EN
Under
Voltage
Lockout
PWM Logic
Current
Limit
PWM
Comparator
Reset
Pulse
Thermal
Shutdown
+
+
+
OVP Comparator
+
ISENSE
Error
Signal
1.13V
Corrective
Ramp
Soft Start
SYNC
Oscillator
+
-
FB
Internal
Compensation
+
Error Amplifier
+
VREF +-
R1
R2
1.0V
GND
+
Freq. Foldback Amplifier
0.53V
+
-
Figure 31.
APPLICATION INFORMATION
THEORY OF OPERATION
The LM27341/LM27342 is a constant-frequency, peak current-mode PWM buck regulator IC that delivers a 1.5
or 2A load current. The regulator has a preset switching frequency of 2 MHz. This high frequency allows the
LM27341/LM27342 to operate with small surface mount capacitors and inductors, resulting in a DC-DC converter
that requires a minimum amount of board space. The LM27341/LM27342 is internally compensated, which
reduces design time, and requires few external components.
The following operating description of the LM27341/LM27342 will refer to the Block Diagram (Figure 31) and to
the waveforms in Figure 32. The LM27341/LM27342 supplies a regulated output voltage by switching the internal
NMOS switch at a constant frequency and varying the duty cycle. A switching cycle begins at the falling edge of
the reset pulse generated by the internal oscillator. When this pulse goes low, the output control logic turns on
the internal NMOS switch. During this on-time, the SW pin voltage (VSW) swings up to approximately VIN, and the
inductor current (iL) increases with a linear slope. The current-sense amplifier measures iL, which generates an
output proportional to the switch current typically called the sense signal. The sense signal is summed with the
regulator’s corrective ramp and compared to the error amplifier’s output, which is proportional to the difference
between the feedback voltage (VFB) and VREF. When the output of the PWM comparator goes high, the switch
turns off until the next switching cycle begins. During the switch off-time (tOFF), inductor current discharges
through the catch diode D1, which forces the SW pin (VSW) to swing below ground by the forward voltage (VD1)
of the catch diode. The regulator loop adjusts the duty cycle (D) to maintain a constant output voltage.
10
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
LM27341, LM27342, LM27341-Q1, LM27342-Q1
www.ti.com
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
VSW
D = tON/TSW
SW Voltage
VIN
tOFF
tON
0
-VD1
Inductor Current
iL
t
TSW
ILPK
IOUT
'iL
0
t
Figure 32. LM27341/LM27342 Waveforms of SW Pin Voltage and Inductor Current
BOOST FUNCTION
Capacitor C2 in Figure 31, commonly referred to as CBOOST, is used to store a voltage VBOOST. When the
LM27341/LM27342 starts up, an internal LDO charges CBOOST ,via an internal diode, to a voltage sufficient to
turn the internal NMOS switch on. The gate drive voltage supplied to the internal NMOS switch is VBOOST - VSW.
During a normal switching cycle, when the internal NMOS control switch is off (tOFF) (refer to Figure 32), VBOOST
equals VLDO minus the forward voltage of the internal diode (VD2). At the same time the inductor current (iL)
forward biases the catch diode D1 forcing the SW pin to swing below ground by the forward voltage drop of the
catch diode (VD1). Therefore, the voltage stored across CBOOST is
VBOOST - VSW = VLDO - VD2 + VD1
(1)
Thus,
VBOOST = VSW + VLDO - VD2 + VD1
(2)
When the NMOS switch turns on (tON), the switch pin rises to
VSW = VIN – (RDSON x IL),
(3)
reverse biasing D1, and forcing VBOOST to rise. The voltage at VBOOST is then
VBOOST = VIN – (RDSON x IL) + VLDO – VD2 + VD1
(4)
which is approximately
VIN + VLDO- 0.4V
(5)
VBOOST has pulled itself up by its "bootstraps", or boosted to a higher voltage.
LOW INPUT VOLTAGE CONSIDERATIONS
When the input voltage is below 5V and the duty cycle is greater than 75 percent, the gate drive voltage
developed across CBOOST might not be sufficient for proper operation of the NMOS switch. In this case, CBOOST
should be charged via an external Schottky diode attached to a 5V voltage rail, see Figure 33. This ensures that
the gate drive voltage is high enough for proper operation of the NMOS switch in the triode region. Maintain
VBOOST - VSW less than the 6V absolute maximum rating.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
11
LM27341, LM27342, LM27341-Q1, LM27342-Q1
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
www.ti.com
D2
VIN
PVIN
5V
BOOST
C2
AVIN
L1
C1
VOUT
SW
C3
D1
LM27342
ON
EN
OFF
R1
SYNC
CLK
FB
GND/DAP
R2
Figure 33. External Diode Charges CBOOST
HIGH OUTPUT VOLTAGE CONSIDERATIONS
When the output voltage is greater than 3.3V, a minimum load current is needed to charge CBOOST, see
Figure 34. The minimum load current forward biases the catch diode D1 forcing the SW pin to swing below
ground. This allows CBOOST to charge, ensuring that the gate drive voltage is high enough for proper operation.
The minimum load current depends on many factors including the inductor value.
Figure 34. Minimum Load Current for L = 1.5 µH
ENABLE PIN / SHUTDOWN MODE
Connect the EN pin to a voltage source greater than 1.8V to enable operation of the LM27341/LM27342. Apply a
voltage less than 0.4V to put the part into shutdown mode. In shutdown mode the quiescent current drops to
typically 70 nA. Switch leakage adds another 40 nA from the input supply. For proper operation, the
LM27341/LM27342 EN pin should never be left floating, and the voltage should never exceed VIN + 0.3V.
The simplest way to enable the operation of the LM27341/LM27342 is to connect the EN pin to AVIN which
allows self start-up of the LM27341/LM27342 when the input voltage is applied.
When the rise time of VIN is longer than the soft-start time of the LM27341/LM27342 this method may result in an
overshoot in output voltage. In such applications, the EN pin voltage can be controlled by a separate logic signal,
or tied to a resistor divider, which reaches 1.8V after VIN is fully established (see Figure 35). This will minimize
the potential for output voltage overshoot during a slow VIN ramp condition. Use the lowest value of VIN , seen in
your application when calculating the resistor network, to ensure that the 1.8V minimum EN threshold is reached.
12
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
LM27341, LM27342, LM27341-Q1, LM27342-Q1
www.ti.com
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
VIN
PVIN
BOOST
C2
AVIN
L1
C1
VOUT
SW
R3
C3
D1
LM27342
EN
R4
R1
SYNC
CLK
FB
GND/DAP
R2
Figure 35. Resistor Divider on EN
R3 =
VIN
- 1 x R4
1.8
(6)
FREQUENCY SYNCHRONIZATION
The LM27341/LM27342 switching frequency can be synchronized to an external clock, between 1.00 and 2.35
MHz, applied at the SYNC pin. At the first rising edge applied to the SYNC pin, the internal oscillator is
overridden and subsequent positive edges will initiate switching cycles. If the external SYNC signal is lost during
operation, the LM27341/LM27342 will revert to its internal 2 MHz oscillator within 1.5 µs. To disable Frequency
Synchronization and utilize the internal 2 MHz oscillator, connect the SYNC pin to GND.
The SYNC pin gives the designer the flexibility to optimize their design. A lower switching frequency can be
chosen for higher efficiency. A higher switching frequency can be chosen to keep EMI out of sensitive ranges
such as the AM radio band. Synchronization can also be used to eliminate beat frequencies generated by the
interaction of multiple switching power converters. Synchronizing multiple switching power converters will result
in cleaner power rails.
The selected switching frequency (fSYNC) and the minimum on-time (tMIN) limit the minimum duty cycle (DMIN) of
the device.
DMIN= tMIN x fSYNC
(7)
Operation below DMIN is not reccomended. The LM27341/LM27342 will skip pulses to keep the output voltage in
regulation, and the current limit is not ensured. The switching is in phase but no longer at the same switching
frequency as the SYNC signal.
CURRENT LIMIT
The LM27341 and LM27342 use cycle-by-cycle current limiting to protect the output switch. During each
switching cycle, a current limit comparator detects if the output switch current exceeds 2.0A min (LM27341) or
2.5A min (LM27342) , and turns off the switch until the next switching cycle begins.
FREQUENCY FOLDBACK
The LM27341/LM27342 employs frequency foldback to protect the device from current run-away during output
short-circuit. Once the FB pin voltage falls below regulation, the switch frequency will smoothly reduce with the
falling FB voltage until the switch frequency reaches 220 kHz (typ). If the device is synchronized to an external
clock, synchronization is disabled until the FB pin voltage exceeds 0.53V
SOFT-START
The LM27341/LM27342 has a fixed internal soft-start of 1 ms (typ). During soft-start, the error amplifier’s
reference voltage ramps from 0.0 V to its nominal value of 1.0 V in approximately 1 ms. This forces the regulator
output to ramp in a controlled fashion, which helps reduce inrush current. Upon soft-start the part will initially be
in frequency foldback and the frequency will rise as FB rises. The regulator will gradually rise to 2 MHz. The
LM27341/LM27342 will allow synchronization to an external clock at FB > 0.53V.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
13
LM27341, LM27342, LM27341-Q1, LM27342-Q1
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
www.ti.com
OUTPUT OVERVOLTAGE PROTECTION
The overvoltage comparator turns off the internal power NFET when the FB pin voltage exceeds the internal
reference voltage by 13% (VFB > 1.13 * VREF). With the power NFET turned off the output voltage will decrease
toward the regulation level.
UNDERVOLTAGE LOCKOUT
Undervoltage lockout (UVLO) prevents the LM27341/LM27342 from operating until the input voltage exceeds
2.75V(typ).
The UVLO threshold has approximately 470 mV of hysteresis, so the part will operate until VIN drops below
2.28V(typ). Hysteresis prevents the part from turning off during power up if VIN has finite impedance.
THERMAL SHUTDOWN
Thermal shutdown limits total power dissipation by turning off the internal NMOS switch when the IC junction
temperature exceeds 165°C (typ). After thermal shutdown occurs, hysteresis prevents the internal NMOS switch
from turning on until the junction temperature drops to approximately 150°C.
Design Guide
INDUCTOR SELECTION
Inductor selection is critical to the performance of the LM27341/LM27342. The selection of the inductor affects
stability, transient response and efficiency. A key factor in inductor selection is determining the ripple current (ΔiL)
(see Figure 32).
The ripple current (ΔiL) is important in many ways.
First, by allowing more ripple current, lower inductance values can be used with a corresponding decrease in
physical dimensions and improved transient response. On the other hand, allowing less ripple current will
increase the maximum achievable load current and reduce the output voltage ripple (see OUTPUT CAPACITOR
section for more details on calculating output voltage ripple). Increasing the maximum load current is achieved by
ensuring that the peak inductor current (ILPK) never exceeds the minimum current limit of 2.0A min (LM27341) or
2.5A min (LM27342) .
ILPK = IOUT + ΔiL / 2
(8)
Secondly, the slope of the ripple current affects the current control loop. The LM27341/LM27342 has a fixed
slope corrective ramp. When the slope of the current ripple becomes significantly less than the converter’s
corrective ramp (see Figure 31), the inductor pole will move from high frequencies to lower frequencies. This
negates one advantage that peak current-mode control has over voltage-mode control, which is, a single low
frequency pole in the power stage of the converter. This can reduce the phase margin, crossover frequency and
potentially cause instability in the converter. Contrarily, when the slope of the ripple current becomes significantly
greater than the converter’s corrective ramp, resonant peaking can occur in the control loop. This can also cause
instability (Sub-Harmonic Oscillation) in the converter. For the power supply designer this means that for lower
switching frequencies the current ripple must be increased to keep the inductor pole well above crossover. It also
means that for higher switching frequencies the current ripple must be decreased to avoid resonant peaking.
With all these factors, how is the desired ripple current selected? The ripple ratio (r) is defined as the ratio of
inductor ripple current (ΔiL) to output current (IOUT), evaluated at maximum load:
r=
'iL
lOUT
(9)
A good compromise between physical size, transient response and efficiency is achieved when we set the ripple
ratio between 0.2 and 0.4. The recommended ripple ratio vs. duty cycle shown below (see Figure 36) is based
upon this compromise and control loop optimizations. Note that this is just a guideline. Please see Application
note AN-1197 SNVA038 for further considerations.
14
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
LM27341, LM27342, LM27341-Q1, LM27342-Q1
www.ti.com
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
Figure 36. Recommended Ripple Ratio Vs. Duty Cycle
The Duty Cycle (D) can be approximated quickly using the ratio of output voltage (VOUT) to input voltage (VIN):
D=
VOUT
VIN
(10)
The application's lowest input voltage should be used to calculate the ripple ratio. The catch diode forward
voltage drop (VD1) and the voltage drop across the internal NFET (VDS) must be included to calculate a more
accurate duty cycle. Calculate D by using the following formula:
VOUT + VD1
D=
VIN + VD1 - VDS
(11)
VDS can be approximated by:
VDS = IOUT x RDS(ON)
(12)
The diode forward drop (VD1) can range from 0.3V to 0.5V depending on the quality of the diode. The lower VD1
is, the higher the operating efficiency of the converter.
Now that the ripple current or ripple ratio is determined, the required inductance is calculated by:
VOUT + VD1
x (1-DMIN)
L=
IOUT x r x fSW
where
•
•
•
DMIN is the duty cycle calculated with the maximum input voltage
fsw is the switching frequency
IOUT is the maximum output current of 2A
(13)
Using IOUT = 2A will minimize the inductor's physical size.
INDUCTOR CALCULATION EXAMPLE
Operating conditions for the LM27342 are:
VIN = 7 - 16V
VOUT = 3.3V
fSW = 2 MHz
VD1 = 0.5V
Copyright © 2008–2013, Texas Instruments Incorporated
IOUT = 2A
Submit Documentation Feedback
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
15
LM27341, LM27342, LM27341-Q1, LM27342-Q1
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
www.ti.com
First the maximum duty cycle is calculated.
DMAX = (VOUT + VD1) / (VIN + VD1 - VDS)
= (3.3V + 0.5V) / (7V + 0.5V - 0.30V)
= 0.528
(14)
Using Figure 36 gives us a recommended ripple ratio = 0.4.
Now the minimum duty cycle is calculated.
DMIN = (VOUT + VD1) / (VIN + VD1 - VDS)
= (3.3V + 0.5V) / (16V + 0.5V - 0.30V)
= 0.235
(15)
The inductance can now be calculated.
L = (1 - DMIN) x (VOUT + VD1) / (IOUT x r x fsw)
= (1 - 0.235) x (3.3V + .5V) / (2A x 0.4 x 2 MHz)
= 1.817 µH
(16)
This is close to the standard inductance value of 1.8 µH. This leads to a 1% deviation from the recommended
ripple ratio, which is now 0.4038.
Finally, we check that the peak current does not reach the minimum current limit of 2.5A.
ILPK = IOUT x (1 + r / 2)
= 2A x (1 + .4038 / 2 )
= 2.404A
(17)
The peak current is less than 2.5A, so the DC load specification can be met with this ripple ratio. To design for
the LM27341 simply replace IOUT = 1.5A in the equations for ILPK and see that ILPK does not exceed the
LM27341's current limit of 2.0A (min).
INDUCTOR MATERIAL SELECTION
When selecting an inductor, make sure that it is capable of supporting the peak output current without saturating.
Inductor saturation will result in a sudden reduction in inductance and prevent the regulator from operating
correctly. To prevent the inductor from saturating over the entire -40 °C to 125 °C range, pick an inductor with a
saturation current higher than the upper limit of ICL listed in the Electrical Characteristics table.
Ferrite core inductors are recommended to reduce AC loss and fringing magnetic flux. The drawback of ferrite
core inductors is their quick saturation characteristic. The current limit circuit has a propagation delay and so is
oftentimes not fast enough to stop a saturated inductor from going above the current limit. This has the potential
to damage the internal switch. To prevent a ferrite core inductor from getting into saturation, the inductor
saturation current rating should be higher than the switch current limit ICL. The LM27341/LM27342 is quite robust
in handling short pulses of current that are a few amps above the current limit. Saturation protection is provided
by a second current limit which is 30% higher than the cycle by cycle current limit. When the saturation protection
is triggered the part will turn off the output switch and attempt to soft-start. (When a compromise has to be made,
pick an inductor with a saturation current just above the lower limit of the ICL.) Be sure to validate the short-circuit
protection over the intended temperature range.
An inductor's saturation current is usually lower when hot. So consult the inductor vendor if the saturation current
rating is only specified at room temperature.
Soft saturation inductors such as the iron powder types can also be used. Such inductors do not saturate
suddenly and therefore are safer when there is a severe overload or even shorted output. Their physical sizes
are usually smaller than the Ferrite core inductors. The downside is their fringing flux and higher power
dissipation due to relatively high AC loss, especially at high frequencies.
16
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
LM27341, LM27342, LM27341-Q1, LM27342-Q1
www.ti.com
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
INPUT CAPACITOR
An input capacitor is necessary to ensure that VIN does not drop excessively during switching transients. The
primary specifications of the input capacitor are capacitance, voltage, RMS current rating, and Equivalent Series
Inductance (ESL). The recommended input capacitance is 10 µF, although 4.7 µF works well for input voltages
below 6V. The input voltage rating is specifically stated by the capacitor manufacturer. Make sure to check any
recommended deratings and also verify if there is any significant change in capacitance at the operating input
voltage and the operating temperature. The input capacitor maximum RMS input current rating (IRMS-IN) must be
greater than:
IRMS-IN = IOUT x
r2
Dx 1-D+
12
where
•
•
•
r is the ripple ratio defined earlier
IOUT is the output current
D is the duty cycle
(18)
It can be shown from the above equation that maximum RMS capacitor current occurs when D = 0.5. Always
calculate the RMS at the point where the duty cycle, D, is closest to 0.5. The ESL of an input capacitor is usually
determined by the effective cross sectional area of the current path. A large leaded capacitor will have high ESL
and a 0805 ceramic chip capacitor will have very low ESL. At the operating frequencies of the
LM27341/LM27342, certain capacitors may have an ESL so large that the resulting impedance (2πfL) will be
higher than that required to provide stable operation. As a result, surface mount capacitors are strongly
recommended. Sanyo POSCAP, Tantalum or Niobium, Panasonic SP or Cornell Dubilier Low ESR are all good
choices for input capacitors and have acceptable ESL. Multilayer ceramic capacitors (MLCC) have very low ESL.
For MLCCs it is recommended to use X7R or X5R dielectrics. Consult the capacitor manufacturer's datasheet to
see how rated capacitance varies over operating conditions.
OUTPUT CAPACITOR
The output capacitor is selected based upon the desired output ripple and transient response. The LM27341/2's
loop compensation is designed for ceramic capacitors. A minimum of 22 µF is required at 2 MHz (33 uF at 1
MHz) while 47 - 100 µF is recommended for improved transient response and higher phase margin. The output
voltage ripple of the converter is:
'VOUT = 'iL x (RESR +
1
)
8 x fSW x COUT
(19)
When using MLCCs, the ESR is typically so low that the capacitive ripple may dominate. When this occurs, the
output ripple will be approximately sinusoidal and 90° phase shifted from the switching action. Another benefit of
ceramic capacitors is their ability to bypass high frequency noise. A certain amount of switching edge noise will
couple through parasitic capacitances in the inductor to the output. A ceramic capacitor will bypass this noise
while a tantalum will not.
The transient response is determined by the speed of the control loop and the ability of the output capacitor to
provide the initial current of a load transient. Capacitance can be increased significantly with little detriment to the
regulator stability. However, increasing the capacitance provides dimininshing improvement over 100 uF in most
applications, because the bandwidth of the control loop decreases as output capacitance increases. If improved
transient performance is required, add a feed forward capacitor. This becomes especially important for higher
output voltages where the bandwidth of the LM27341/LM27342 is lower. See FEED FORWARD CAPACITOR
(OPTIONAL) and FREQUENCY SYNCHRONIZATION sections.
Check the RMS current rating of the capacitor. The RMS current rating of the capacitor chosen must also meet
the following condition:
IRMS-OUT = IOUT x
r
12
where
•
•
IOUT is the output current
r is the ripple ratio.
Copyright © 2008–2013, Texas Instruments Incorporated
(20)
Submit Documentation Feedback
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
17
LM27341, LM27342, LM27341-Q1, LM27342-Q1
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
www.ti.com
CATCH DIODE
The catch diode (D1) conducts during the switch off-time. A Schottky diode is recommended for its fast switching
times and low forward voltage drop. The catch diode should be chosen so that its current rating is greater than:
ID1 = IOUT x (1-D)
(21)
The reverse breakdown rating of the diode must be at least the maximum input voltage plus appropriate margin.
To improve efficiency choose a Schottky diode with a low forward voltage drop.
BOOST DIODE (OPTIONAL)
For circuits with input voltages VIN < 5V and duty cycles (D) >0.75V. a small-signal Schottky diode is
recommended. A good choice is the BAT54 small signal diode. The cathode of the diode is connected to the
BOOST pin and the anode to a 5V voltage rail.
BOOST CAPACITOR
A ceramic 0.1 µF capacitor with a voltage rating of at least 6.3V is sufficient. The X7R and X5R MLCCs provide
the best performance.
OUTPUT VOLTAGE
The output voltage is set using the following equation where R2 is connected between the FB pin and GND, and
R1 is connected between VOUT and the FB pin. A good starting value for R2 is 1 kΩ.
R1 =
VOUT
VREF
- 1 x R2
(22)
FEED FORWARD CAPACITOR (OPTIONAL)
A feed forward capacitor CFF can improve the transient response of the converter. Place CFF in parallel with R1.
The value of CFF should place a zero in the loop response at, or above, the pole of the output capacitor and
RLOAD. The CFF capacitor will increase the crossover frequency of the design, thus a larger minimum output
capacitance is required for designs using CFF. CFF should only be used with an output capacitance greater than
or equal to 44 uF.
VOUT x COUT
CFF <=
IOUT x R1
(23)
Calculating Efficiency, and Junction Temperature
The complete LM27341/LM27342 DC-DC converter efficiency can be calculated in the following manner.
POUT
K=
PIN
(24)
Or
K=
POUT
POUT + PLOSS
(25)
Calculations for determining the most significant power losses are shown below. Other losses totaling less than
2% are not discussed.
Power loss (PLOSS) is the sum of two basic types of losses in the converter, switching and conduction.
Conduction losses usually dominate at higher output loads, where as switching losses remain relatively fixed and
dominate at lower output loads. The first step in determining the losses is to calculate the duty cycle (D).
D=
18
VOUT + VD1
VIN + VD1 - VDS
(26)
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
LM27341, LM27342, LM27341-Q1, LM27342-Q1
www.ti.com
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
VDS is the voltage drop across the internal NFET when it is on, and is equal to:
VDS = IOUT x RDSON
(27)
VD is the forward voltage drop across the Schottky diode. It can be obtained from the Electrical Characteristics
section of the schottky diode datasheet. If the voltage drop across the inductor (VDCR) is accounted for, the
equation becomes:
D=
VOUT + VD1 + VDCR
VIN + VD1 - VDS
(28)
VDCR usually gives only a minor duty cycle change, and has been omitted in the examples for simplicity.
SCHOTTKY DIODE CONDUCTION LOSSES
The conduction losses in the free-wheeling Schottky diode are calculated as follows:
PDIODE = VD1 x IOUT (1-D)
(29)
Often this is the single most significant power loss in the circuit. Care should be taken to choose a Schottky
diode that has a low forward voltage drop.
INDUCTOR CONDUCTION LOSSES
Another significant external power loss is the conduction loss in the output inductor. The equation can be
simplified to:
PIND = IOUT2 x RDCR
(30)
MOSFET CONDUCTION LOSSES
The LM27341/LM27342 conduction loss is mainly associated with the internal NFET:
PCOND = IOUT2 x RDSON x D
(31)
MOSFET SWITCHING LOSSES
Switching losses are also associated with the internal NFET. They occur during the switch on and off transition
periods, where voltages and currents overlap resulting in power loss. The simplest means to determine this loss
is to empirically measuring the rise and fall times (10% to 90%) of the switch at the switch node:
PSWF = 1/2(VIN x IOUT x fSW x tFALL)
PSWR = 1/2(VIN x IOUT x fSW x tRISE)
PSW = PSWF + PSWR
(32)
(33)
(34)
Table 1. Typical Rise and Fall Times vs Input Voltage
VIN
tRISE
tFALL
5V
8ns
8ns
10V
9ns
9ns
15V
10ns
10ns
IC QUIESCENT LOSSES
Another loss is the power required for operation of the internal circuitry:
PQ = IQ x VIN
(35)
IQ is the quiescent operating current, and is typically around 2.4 mA.
MOSFET DRIVER LOSSES
The other operating power that needs to be calculated is that required to drive the internal NFET:
PBOOST = IBOOST x VBOOST
(36)
VBOOST is normally between 3VDC and 5VDC. The IBOOST rms current is dependant on switching frequency fSW.
IBOOST is approximately 8.2 mA at 2 MHz and 4.4 mA at 1 MHz.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
19
LM27341, LM27342, LM27341-Q1, LM27342-Q1
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
www.ti.com
TOTAL POWER LOSSES
Total power losses are:
PLOSS = PCOND + PSWR + PSWF + PQ + PBOOST + PDIODE + PIND
(37)
Losses internal to the LM27341/LM27342 are:
PINTERNAL = PCOND + PSWR + PSWF + PQ + PBOOST
(38)
EFFICIENCY CALCULATION EXAMPLE
Operating conditions are:
VIN = 12V
VOUT = 3.3V
IOUT = 2A
fSW = 2 MHz
VD1 = 0.5V
RDCR = 20 mΩ
Internal Power Losses are:
PCOND = IOUT2 x RDSON x D
= 22 x 0.15Ω x 0.314
= 188 mW
PSW = (VIN x IOUT x fSW x tFALL)
= (12V x 2A x 2 MHz x 10ns)
= 480 mW
PQ = IQ x VIN
= 2.4 mA x 12V
= 29 mW
PBOOST = IBOOST x VBOOST
= 8.2 mA x 4.5V
= 37 mW
PINTERNAL = PCOND + PSW + PQ + PBOOST= 733 mW
(39)
(40)
(41)
(42)
(43)
Total Power Losses are:
PDIODE = VD1 x IOUT (1 - D)
= 0.5V x 2 x (1 - 0.314)
= 686 mW
PIND = IOUT2 x RDCR
= 22 x 20 mΩ
= 80 mW
PLOSS = PINTERNAL + PDIODE + PIND = 1.499 W
(45)
(46)
The efficiency can now be estimated as:
POUT
6.6 W
=
= 81 %
K=
POUT + PLOSS 6.6 W + 1.499 W
(47)
(44)
With this information we can estimate the junction temperature of the LM27341/LM27342.
CALCULATING THE LM27341/LM27342 JUNCTION TEMPERATURE
Thermal Definitions:
TJ = IC junction temperature
TA = Ambient temperature
RθJC = Thermal resistance from IC junction to device case
RθJA = Thermal resistance from IC junction to ambient air
20
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
LM27341, LM27342, LM27341-Q1, LM27342-Q1
www.ti.com
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
Figure 37. Cross-Sectional View of Integrated Circuit Mounted on a Printed Circuit Board.
Heat in the LM27341/LM27342 due to internal power dissipation is removed through conduction and/or
convection.
Conduction: Heat transfer occurs through cross sectional areas of material. Depending on the material, the
transfer of heat can be considered to have poor to good thermal conductivity properties (insulator vs conductor).
Heat Transfer goes as:
Silicon→Lead Frame→PCB
Convection: Heat transfer is by means of airflow. This could be from a fan or natural convection. Natural
convection occurs when air currents rise from the hot device to cooler air.
Thermal impedance is defined as:
RT =
'T
Power
(48)
Thermal impedance from the silicon junction to the ambient air is defined as:
RTJA =
TJ - TA
Power
(49)
This impedance can vary depending on the thermal properties of the PCB. This includes PCB size, weight of
copper used to route traces , the ground plane, and the number of layers within the PCB. The type and number
of thermal vias can also make a large difference in the thermal impedance. Thermal vias are necessary in most
applications. They conduct heat from the surface of the PCB to the ground plane. Six to nine thermal vias should
be placed under the exposed pad to the ground plane. Placing more than nine thermal vias results in only a
small reduction to RθJA for the same copper area. These vias should have 8 mil holes to avoid wicking solder
away from the DAP. See SNOA401 and SNVA183 for more information on package thermal performance. If a
compromise for cost needs to be made, the thermal vias for the MSOP-PowerPad package can range from 8-14
mils, this will increase the possibility of solder wicking.
To predict the silicon junction temperature for a given application, three methods can be used. The first is useful
before prototyping and the other two can more accurately predict the junction temperature within the application.
Method 1:
The first method predicts the junction temperature by extrapolating a best guess RθJA from the table or graph.
The tables and graph are for natural convection. The internal dissipation can be calculated using the efficiency
calculations. This allows the user to make a rough prediction of the junction temperature in their application.
Methods two and three can later be used to determine the junction temperature more accurately.
The two tables below have values of RθJA for the SON and the MSOP-PowerPad packages.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
21
LM27341, LM27342, LM27341-Q1, LM27342-Q1
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
www.ti.com
RθJA values for the MSOP-PowerPad @ 1Watt dissipation:
Number of Board
Layers
Size of Bottom Layer Copper
Connected to DAP
Size of Top Layer Copper
Connected to Dap
Number of 10 mil
Thermal Vias
RθJA
2
0.25 in2
0.05 in2
8
80.6 °C/W
2
2
2
0.5625 in
0.05 in
8
70.9 °C/W
2
1 in2
0.05 in2
8
62.1 °C/W
2
1.3225 in2
0.05 in2
8
54.6 °C/W
4 (Eval Board)
3.25 in2
2.25 in2
14
35.3 °C/W
RθJA
RθJA values for the SON @ 1Watt dissipation:
Number of Board
Layers
Size of Bottom Layer Copper
Connected to DAP
Size of Top Layer Copper
Connected to Dap
Number of 8 mil
Thermal Vias
2
0.25 in2
0.05 in2
8
78 °C/W
2
0.5625 in
0.05 in2
8
65.6 °C/W
2
1 in2
0.05 in2
8
58.6 °C/W
2
1.3225 in2
0.05 in2
8
50 °C/W
15
30.7 °C/W
2
2
4 (Eval Board)
3.25 in
2
2.25 in
Figure 38. Estimate of Thermal Resistance vs. Ground Copper Area
Eight Thermal Vias and Natural Convection
Method 2:
The second method requires the user to know the thermal impedance of the silicon junction to case. (RθJC) is
approximately 9.5°C/W for the MSOP-PowerPad package or 9.1°C/W for the SON. The case temperature should
be measured on the bottom of the PCB at a thermal via directly under the DAP of the LM27341/LM27342. The
solder resist should be removed from this area for temperature testing. The reading will be more accurate if it is
taken midway between pins 2 and 9, where the NMOS switch is located. Knowing the internal dissipation from
the efficiency calculation given previously, and the case temperature (TC) we have:
RTJC =
TJ - TC
Power
(50)
TJ = (RθJC x PLOSS) + TC
(51)
Therefore:
22
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
LM27341, LM27342, LM27341-Q1, LM27342-Q1
www.ti.com
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
METHOD 2 EXAMPLE
The operating conditions are the same as the previous Efficiency Calculation:
VIN = 12V
VOUT = 3.3V
IOUT = 2A
fSW = 2 MHz
VD1 = 0.5V
RDCR = 20 mΩ
Internal Power Losses are:
PCOND = IOUT2 x RDSON x D
= 22 x 0.15Ω x 0.314
= 188 mW
PSW = (VIN x IOUT x fSW x tFALL)
= (12V x 2A x 2 MHz x 10ns)
= 480 mW
PQ = IQ x VIN
= 1.5 mA x 12V
= 29 mW
PBOOST = IBOOST x VBOOST
= 7 mA x 4.5V
= 37 mW
PINTERNAL = PCOND + PSW + PQ + PBOOST = 733 mW
(52)
(53)
(54)
(55)
(56)
The junction temperature can now be estimated as:
TJ = (RθJC x PINTERNAL) + TC
(57)
A Texas Instruments MSOP-PowerPad evaluation board was used to determine the TJ of the
LM27341/LM27342. The four layer PCB is constructed using FR4 with 2oz copper traces. There is a ground
plane on the internal layer directly beneath the device, and a ground plane on the bottom layer. The ground
plane is accessed by fourteen 10 mil vias. The board measures 2in x 2in (50.8mm x 50.8mm). It was placed in a
container with no airflow. The case temperature measured on this LM27342MY Demo Board was 48.7°C.
Therefore,
TJ = (9.5 °C/W x 733 mW) + 48.7 °C
TJ = 55.66 °C
(58)
(59)
To keep the Junction temperature below 125 °C for this layout, the ambient temperature must stay below 94.33
°C.
TA_MAX = TJ_MAX - TJ +TA
TA_MAX = 125 °C - 55.66 °C + 25 °C
TA_MAX = 94.33 °C
(60)
(61)
(62)
Method 3:
The third method can also give a very accurate estimate of silicon junction temperature. The first step is to
determine RθJA of the application. The LM27341/LM27342 has over-temperature protection circuitry. When the
silicon temperature reaches 165 °C, the device stops switching. The protection circuitry has a hysteresis of 15
°C. Once the silicon temperature has decreased to approximately 150 °C, the device will start to switch again.
Knowing this, the RθJA for any PCB can be characterized during the early stages of the design by raising the
ambient temperature in the given application until the circuit enters thermal shutdown. If the SW-pin is monitored,
it will be obvious when the internal NFET stops switching indicating a junction temperature of 165 °C. We can
calculate the internal power dissipation from the above methods. All that is needed for calculation is the estimate
of RDSON at 165 °C. This can be extracted from the graph of RDSON vs. Temperature. The value is approximately
0.267 ohms. With this, the junction temperature, and the ambient temperature RθJA can be determined.
RTJA =
165oC - TA
PINTERNAL
(63)
Once this is determined, the maximum ambient temperature allowed for a desired junction temperature can be
found.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
23
LM27341, LM27342, LM27341-Q1, LM27342-Q1
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
www.ti.com
METHOD 3 EXAMPLE
The operating conditions are the same as the previous Efficiency Calculation:
VIN = 12V
VOUT = 3.3V
IOUT = 2A
fSW = 2 MHz
VD1 = 0.5V
RDCR = 20 mΩ
Internal Power Losses are:
PCOND = IOUT2 x RDSON x D
= 22 x 0.267Ω x .314
= 335 mW
PSW = (VIN x IOUT x fSW x tFALL)
= (12V x 2A x 2 MHz x 10nS)
= 480 mW
PQ = IQ x VIN
= 1.5 mA x 12V
= 29 mW
PBOOST = IBOOST x VBOOST
= 7 mA x 4.5V
= 37 mW
PINTERNAL = PCOND + PSW + PQ + PBOOST = 881 mW
(64)
(65)
(66)
(67)
(68)
Using a Texas Instruments MSOP-PowerPad evaluation board to determine the RθJA of the board. The four layer
PCB is constructed using FR4 with 2oz copper traces. There is a ground plane on the internal layer directly
beneath the device, and a ground plane on the bottom layer. The ground plane is accessed by fourteen 10 mil
vias. The board measures 2in x 2in (50.8mm x 50.8mm). It was placed in an oven with no forced airflow.
The ambient temperature was raised to 132 °C, and at that temperature, the device went into thermal shutdown.
RθJA can now be calculated.
RTJA =
165oC - 132oC
= 37.46 oC/W
0.881 W
(69)
To keep the Junction temperature below 125 °C for this layout, the ambient temperature must stay below 92 °C.
TA_MAX = TJ_MAX - (RθJA x PINTERNAL)
TA_MAX = 125 °C - (37.46 °C/W x 0.881 W)
TA_MAX = 92 °C
(70)
(71)
(72)
This calculation of the maximum ambient temperature is only 2.3 °C different from the calculation using method
2. The methods described above to find the junction temperature in the MSOP-PowerPad package can also be
used to calculate the junction temperature in the SON package. The 10-pin SON package has a RθJC = 9.1°C/W,
while RθJA can vary depending on the layout. RθJA can be calculated in the same manner as described in method
3.
PCB Layout Considerations
COMPACT LAYOUT
The performance of any switching converter depends as much upon the layout of the PCB as the component
selection. The following guidelines will help the user design a circuit with maximum rejection of outside EMI and
minimum generation of unwanted EMI.
Parasitic inductance can be reduced by keeping the power path components close together and keeping the
area of the loops small, on which high currents travel. Short, thick traces or copper pours (shapes) are best. In
particular, the switch node (where L1, D1, and the SW pin connect) should be just large enough to connect all
three components without excessive heating from the current it carries. The LM27341/LM27342 operates in two
distinct cycles (see Figure 32) whose high current paths are shown below in Figure 39:
24
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
LM27341, LM27342, LM27341-Q1, LM27342-Q1
www.ti.com
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
+
-
Figure 39. Buck Converter Current Loops
The dark grey, inner loop represents the high current path during the MOSFET on-time. The light grey, outer loop
represents the high current path during the off-time.
GROUND PLANE AND SHAPE ROUTING
The diagram of Figure 39 is also useful for analyzing the flow of continuous current vs. the flow of pulsating
currents. The circuit paths with current flow during both the on-time and off-time are considered to be continuous
current, while those that carry current during the on-time or off-time only are pulsating currents. Preference in
routing should be given to the pulsating current paths, as these are the portions of the circuit most likely to emit
EMI. The ground plane of a PCB is a conductor and return path, and it is susceptible to noise injection just like
any other circuit path. The path between the input source and the input capacitor and the path between the catch
diode and the load are examples of continuous current paths. In contrast, the path between the catch diode and
the input capacitor carries a large pulsating current. This path should be routed with a short, thick shape,
preferably on the component side of the PCB. Multiple vias in parallel should be used right at the pad of the input
capacitor to connect the component side shapes to the ground plane. A second pulsating current loop that is
often ignored is the gate drive loop formed by the SW and BOOST pins and boost capacitor CBOOST. To minimize
this loop and the EMI it generates, keep CBOOST close to the SW and BOOST pins.
FB LOOP
The FB pin is a high-impedance input, and the loop created by R2, the FB pin and ground should be made as
small as possible to maximize noise rejection. R2 should therefore be placed as close as possible to the FB and
GND pins of the IC.
PCB SUMMARY
1. Minimize the parasitic inductance by keeping the power path components close together and keeping the
area of the high-current loops small.
2. The most important consideration when completing the layout is the close coupling of the GND connections
of the CIN capacitor and the catch diode D1. These ground connections should be immediately adjacent, with
multiple vias in parallel at the pad of the input capacitor connected to GND. Place CIN and D1 as close to the
IC as possible.
3. Next in importance is the location of the GND connection of the COUT capacitor, which should be near the
GND connections of CIN and D1.
4. There should be a continuous ground plane on the copper layer directly beneath the converter. This will
reduce parasitic inductance and EMI.
5. The FB pin is a high impedance node and care should be taken to make the FB trace short to avoid noise
pickup and inaccurate regulation. The feedback resistors should be placed as close as possible to the IC,
with the GND of R2 placed as close as possible to the GND of the IC. The VOUT trace to R1 should be routed
away from the inductor and any other traces that are switching.
6. High AC currents flow through the VIN, SW and VOUT traces, so they should be as short and wide as
possible. However, making the traces wide increases radiated noise, so the layout designer must make this
trade-off. Radiated noise can be decreased by choosing a shielded inductor.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
25
LM27341, LM27342, LM27341-Q1, LM27342-Q1
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
www.ti.com
The remaining components should also be placed as close as possible to the IC. Please see Application Note
AN-1229 SNVA054 for further considerations and the LM27342 demo board as an example of a four-layer
layout.
26
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
LM27341, LM27342, LM27341-Q1, LM27342-Q1
www.ti.com
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
LM27341/LM27342 Circuit Examples
VIN
PVIN
BOOST
C2
AVIN
L1
C1
VOUT
SW
C3
D1
LM27341/2
C4
ON
EN
OFF
R1
SYNC
CLK
2 MHz
FB
GND / DAP
R2
C5
Figure 40. VIN = 7 - 16V, VOUT = 5V, fSW = 2 MHz, IOUT = Full Load
Figure 41. LM27342 Efficiency vs. Load Current
Figure 42. Transient Response
IOUT = 100 mA - 2A @ slewrate = 2A / µs
Table 2. Bill of Materials for Figure 40
Part Name
Part ID
Part Value
Part Number
Manufacturer
Buck Regulator
U1
1.5 or 2A Buck Regulator
LM27341 / LM27342
TI
CPVIN
C1
10 µF
GRM32DR71E106KA12L
Murata
CBOOST
C2
0.1 µF
GRM188R71C104KA01D
Murata
COUT
C3
22 µF
C3225X7R1C226K
TDK
COUT
C4
22 µF
C3225X7R1C226K
TDK
CFF
C5
0.18 µF
0603ZC184KAT2A
AVX
Catch Diode
D1
Schottky Diode Vf = 0.32V
CMS06
Toshiba
Inductor
L1
2.2 µH
CDRHD5D28RHPNP
Sumida
Feedback Resistor
R1
560Ω
CRCW0603560RFKEA
Vishay
Feedback Resistor
R2
140Ω
CRCW0603140RFKEA
Vishay
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
27
LM27341, LM27342, LM27341-Q1, LM27342-Q1
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
VIN
www.ti.com
PVIN
BOOST
C2
AVIN
L1
C1
VOUT
SW
C3
D1
LM27341/2
C4
ON
EN
OFF
R1
SYNC
CLK
1 MHz
FB
GND / DAP
R2
C5
Figure 43. VIN = 7 - 16V, VOUT = 5V, fSW = 1 MHz, IOUT = Full Load
Figure 44. LM27342 Efficiency vs. Load Current
Figure 45. Transient Response
IOUT = 100 mA - 2A @ slewrate = 2A / µs
Table 3. Bill of Materials for Figure 43
Part Name
Part ID
Part Value
Part Number
Manufacturer
Buck Regulator
U1
1.5 or 2A Buck Regulator
LM27341 / LM27342
TI
CPVIN
C1
10 µF
GRM32DR71E106KA12L
Murata
CBOOST
C2
0.1 µF
GRM188R71C104KA01D
Murata
COUT
C3
47 µF
GRM32ER61A476KE20L
Murata
COUT
C4
22 µF
C3225X7R1C226K
TDK
CFF
C5
0. 27 µF
C0603C274K4RACTU
Kemet
Catch Diode
D1
Schottky Diode Vf = 0.32V
CMS06
Toshiba
Inductor
L1
3.3 µH
CDRH6D26HPNP
Sumida
Feedback Resistor
R1
560Ω
CRCW0603560RFKEA
Vishay
Feedback Resistor
R2
140Ω
CRCW0603140RFKEA
Vishay
28
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
LM27341, LM27342, LM27341-Q1, LM27342-Q1
www.ti.com
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
VIN
PVIN
BOOST
C2
AVIN
L1
C1
VOUT
SW
C3
D1
LM27341/2
C4
ON
EN
OFF
R1
SYNC
CLK
2 MHz
FB
GND / DAP
R2
C5
Figure 46. VIN = 5 - 16V, VOUT = 3.3V, fSW = 2 MHz, IOUT = Full Load
Figure 47. LM27342 Efficiency vs. Load Current
Figure 48. Transient Response
IOUT = 100 mA - 2A @ slewrate = 2A / µs
Table 4. Bill of Materials for Figure 46
Part Name
Part ID
Part Value
Part Number
Manufacturer
Buck Regulator
U1
1.5 or 2A Buck Regulator
LM27341 / LM27342
TI
CPVIN
C1
10 µF
GRM32DR71E106KA12L
Murata
CBOOST
C2
0.1 µF
GRM188R71C104KA01D
Murata
COUT
C3
22 µF
C3225X7R1C226K
TDK
COUT
C4
22 µF
C3225X7R1C226K
TDK
CFF
C5
0.18 µF
0603ZC184KAT2A
AVX
Catch Diode
D1
Schottky Diode Vf = 0.32V
CMS06
Toshiba
Inductor
L1
1.5 µH
CDRH5D18BHPNP
Sumida
Feedback Resistor
R1
430 Ω
CRCW0603430RFKEA
Vishay
Feedback Resistor
R2
187 Ω
CRCW0603187RFKEA
Vishay
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
29
LM27341, LM27342, LM27341-Q1, LM27342-Q1
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
VIN
www.ti.com
PVIN
BOOST
C2
AVIN
L1
C1
EN
VOUT
SW
D1
LM27341/2
C3
C4
R1
SYNC
FB
GND / DAP
R2
Figure 49. VIN = 5 - 16V, VOUT = 3.3V, fSW = 2 MHz, IOUT = Full Load
Figure 50. LM27342 Efficiency vs. Load Current
Figure 51. Transient Response
IOUT = 100 mA - 2A @ slewrate = 2A / µs
Table 5. Bill of Materials for Figure 49
Part Name
Part ID
Part Value
Part Number
Manufacturer
Buck Regulator
U1
1.5 or 2A Buck Regulator
LM27341 / LM27342
TI
CPVIN
C1
10 µF
GRM32DR71E106KA12L
Murata
CBOOST
C2
0.1 µF
GRM188R71C104KA01D
Murata
COUT
C3
22 µF
C3225X7R1C226K
TDK
COUT
C4
22 µF
C3225X7R1C226K
TDK
Catch Diode
D1
Schottky Diode Vf = 0.32V
CMS06
Toshiba
Inductor
L1
1.5 µH
CDRH5D18BHPNP
Sumida
Feedback Resistor
R1
430 Ω
CRCW0603430RFKEA
Vishay
Feedback Resistor
R2
187 Ω
CRCW0603187RFKEA
Vishay
30
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
LM27341, LM27342, LM27341-Q1, LM27342-Q1
www.ti.com
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
VIN
PVIN
BOOST
C2
AVIN
L1
C1
VOUT
SW
D1
LM27341/2
C3
C4
ON
EN
OFF
R1
SYNC
CLK
1 MHz
FB
GND / DAP
R2
C5
Figure 52. VIN = 5 - 16V, VOUT = 3.3V, fSW = 1 MHz, IOUT = Full Load
Figure 53. LM27342 Efficiency vs. Load Current
Figure 54. Transient Response
IOUT = 100 mA - 2A @ slewrate = 2A / µs
Table 6. Bill of Materials for Figure 52
Part Name
Part ID
Part Value
Part Number
Manufacturer
Buck Regulator
U1
1.5 or 2A Buck Regulator
LM27341 / LM27342
TI
CPVIN
C1
10 µF
GRM32DR71E106KA12L
Murata
CBOOST
C2
0.1 µF
GRM188R71C104KA01D
Murata
COUT
C3
47 µF
GRM32ER61A476KE20L
Murata
COUT
C4
22 µF
C3225X7R1C226K
TDK
CFF
C5
0.27 µF
C0603C274K4RACTU
Kemet
Catch Diode
D1
Schottky Diode Vf = 0.32V
CMS06
Toshiba
Inductor
L1
2.7 µH
CDRH5D18BHPNP
Sumida
Feedback Resistor
R1
430 Ω
CRCW0603430RFKEA
Vishay
Feedback Resistor
R2
187 Ω
CRCW0603187RFKEA
Vishay
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
31
LM27341, LM27342, LM27341-Q1, LM27342-Q1
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
VIN
www.ti.com
PVIN
BOOST
C2
AVIN
L1
C1
EN
VOUT
SW
D1
LM27341/2
C3
C4
R1
SYNC
FB
GND / DAP
R2
Figure 55. VIN = 3.3 - 16V, VOUT = 1.8V, fSW = 2 MHz, IOUT = Full Load
Figure 56. LM27342 Efficiency vs. Load Current
Figure 57. Transient Response
IOUT = 100 mA - 2A @ slewrate = 2A / µs
Table 7. Bill of Materials for Figure 55
Part Name
Part ID
Part Value
Part Number
Manufacturer
Buck Regulator
U1
1.5 or 2A Buck Regulator
LM27341 / LM27342
TI
CPVIN
C1
10 µF
GRM32DR71E106KA12L
Murata
CBOOST
C2
0.1 µF
GRM188R71C104KA01D
Murata
COUT
C3
22 µF
C3225X7R1C226K
TDK
COUT
C4
22 µF
C3225X7R1C226K
TDK
Catch Diode
D1
Schottky Diode Vf = 0.32V
CMS06
Toshiba
Inductor
L1
1.0 µH
CDRH5D18BHPNP
Sumida
Feedback Resistor
R1
12 kΩ
CRCW060312K0FKEA
Vishay
Feedback Resistor
R2
15 kΩ
CRCW060315K0FKEA
Vishay
32
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
LM27341, LM27342, LM27341-Q1, LM27342-Q1
www.ti.com
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
VIN
PVIN
BOOST
C2
AVIN
L1
C1
VOUT
SW
D1
LM27341/2
C3
C4
ON
EN
OFF
R1
SYNC
CLK
1 MHz
FB
GND / DAP
R2
C5
Figure 58. VIN = 3.3 - 16V, VOUT = 1.8V, fSW = 1 MHz, IOUT = Full Load
Figure 59. LM27342 Efficiency vs. Load Current
Figure 60. Transient Response
IOUT = 100 mA - 2A @ slewrate = 2A / µs
Table 8. Bill of Materials for Figure 58
Part Name
Part ID
Part Value
Part Number
Manufacturer
Buck Regulator
U1
1.5 or 2A Buck Regulator
LM27341 / LM27342
TI
CPVIN
C1
10 µF
GRM32DR71E106KA12L
Murata
CBOOST
C2
0.1 µF
GRM188R71C104KA01D
Murata
COUT
C3
22 uF
C3225X7R1C226K
TDK
COUT
C4
22 uF
C3225X7R1C226K
TDK
CFF
C5
3.9 nF
GRM188R71H392KA01D
Murata
Catch Diode
D1
Schottky Diode Vf = 0.32V
CMS06
Toshiba
Inductor
L1
1.8 µH
CDRH5D18BHPNP
Sumida
Feedback Resistor
R1
12 kΩ
CRCW060312K0FKEA
Vishay
Feedback Resistor
R2
15 kΩ
CRCW060315K0FKEA
Vishay
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
33
LM27341, LM27342, LM27341-Q1, LM27342-Q1
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
VIN
www.ti.com
PVIN
BOOST
C2
AVIN
L1
C1
VOUT
SW
C3
D1
LM27341/2
C4
ON
EN
OFF
R1
SYNC
CLK
2 MHz
FB
GND / DAP
R2
C5
Figure 61. VIN = 3.3 - 9V, VOUT = 1.2V, fSW = 2 MHz, IOUT = Full Load
Figure 62. LM27342 Efficiency vs. Load Current
Figure 63. Transient Response
IOUT = 100 mA - 2A @ slewrate = 2A / µs
Table 9. Bill of Materials for Figure 61
Part Name
Part ID
Part Value
Part Number
Manufacturer
Buck Regulator
U1
1.5 or 2A Buck Regulator
LM27341 / LM27342
TI
CPVIN
C1
10 µF
GRM32DR71E106KA12L
Murata
CBOOST
C2
0.1 µF
GRM188R71C104KA01D
Murata
COUT
C3
47 µF
GRM32ER61A476KE20L
Murata
COUT
C4
22 µF
C3225X7R1C226K
TDK
CFF
C5
NOT MOUNTED
Catch Diode
D1
Schottky Diode Vf = 0.32V
CMS06
Toshiba
Inductor
L1
0.56 µH
CDRH2D18/HPNP
Sumida
Feedback Resistor
R1
1.02 kΩ
CRCW06031K02FKEA
Vishay
Feedback Resistor
R2
5.10 kΩ
CRCW06035K10FKEA
Vishay
34
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
LM27341, LM27342, LM27341-Q1, LM27342-Q1
www.ti.com
SNVS497E – NOVEMBER 2008 – REVISED APRIL 2013
REVISION HISTORY
Changes from Revision D (April 2013) to Revision E
•
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 34
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LM27341 LM27342 LM27341-Q1 LM27342-Q1
35
PACKAGE OPTION ADDENDUM
www.ti.com
8-Oct-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM27341MY/NOPB
ACTIVE
MSOPPowerPAD
DGQ
10
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
-40 to 125
SSCB
LM27341QMY/NOPB
ACTIVE
MSOPPowerPAD
DGQ
10
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
-40 to 125
SSJB
LM27341QMYX/NOPB
ACTIVE
MSOPPowerPAD
DGQ
10
3500
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
-40 to 125
SSJB
LM27341SD/NOPB
ACTIVE
WSON
DSC
10
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L231B
LM27342MY/NOPB
ACTIVE
MSOPPowerPAD
DGQ
10
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
-40 to 125
SSCA
LM27342MYX/NOPB
ACTIVE
MSOPPowerPAD
DGQ
10
3500
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
-40 to 125
SSCA
LM27342QMY/NOPB
ACTIVE
MSOPPowerPAD
DGQ
10
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
-40 to 125
SSJA
LM27342QMYX/NOPB
ACTIVE
MSOPPowerPAD
DGQ
10
3500
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
-40 to 125
SSJA
LM27342SD/NOPB
ACTIVE
WSON
DSC
10
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L231A
LM27342SDX/NOPB
ACTIVE
WSON
DSC
10
4500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
L231A
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
8-Oct-2015
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LM27341, LM27341-Q1, LM27342, LM27342-Q1 :
• Catalog: LM27341, LM27342
• Automotive: LM27341-Q1, LM27342-Q1
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Sep-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LM27341MY/NOPB
MSOPPower
PAD
DGQ
10
1000
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM27341QMY/NOPB
MSOPPower
PAD
DGQ
10
1000
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM27341QMYX/NOPB
MSOPPower
PAD
DGQ
10
3500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM27341SD/NOPB
WSON
DSC
10
1000
178.0
12.4
3.3
3.3
1.0
8.0
12.0
Q1
LM27342MY/NOPB
MSOPPower
PAD
DGQ
10
1000
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM27342MYX/NOPB
MSOPPower
PAD
DGQ
10
3500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM27342QMY/NOPB
MSOPPower
PAD
DGQ
10
1000
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LM27342QMYX/NOPB
MSOPPower
PAD
DGQ
10
3500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Sep-2015
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LM27342SD/NOPB
WSON
DSC
10
1000
178.0
12.4
3.3
3.3
1.0
8.0
12.0
Q1
LM27342SDX/NOPB
WSON
DSC
10
4500
330.0
12.4
3.3
3.3
1.0
8.0
12.0
Q1
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM27341MY/NOPB
MSOP-PowerPAD
DGQ
10
1000
213.0
191.0
55.0
LM27341QMY/NOPB
MSOP-PowerPAD
DGQ
10
1000
213.0
191.0
55.0
LM27341QMYX/NOPB
MSOP-PowerPAD
DGQ
10
3500
367.0
367.0
35.0
LM27341SD/NOPB
WSON
DSC
10
1000
210.0
185.0
35.0
LM27342MY/NOPB
MSOP-PowerPAD
DGQ
10
1000
213.0
191.0
55.0
LM27342MYX/NOPB
MSOP-PowerPAD
DGQ
10
3500
367.0
367.0
35.0
LM27342QMY/NOPB
MSOP-PowerPAD
DGQ
10
1000
213.0
191.0
55.0
LM27342QMYX/NOPB
MSOP-PowerPAD
DGQ
10
3500
367.0
367.0
35.0
LM27342SD/NOPB
WSON
DSC
10
1000
210.0
185.0
35.0
LM27342SDX/NOPB
WSON
DSC
10
4500
367.0
367.0
35.0
Pack Materials-Page 2
MECHANICAL DATA
DGQ0010A
MUC10A (Rev A)
BOTTOM VIEW
www.ti.com
PACKAGE OUTLINE
DSC0010B
WSON - 0.8 mm max height
SCALE 4.000
PLASTIC SMALL OUTLINE - NO LEAD
3.1
2.9
B
A
PIN 1 INDEX AREA
3.1
2.9
C
0.8 MAX
0.08
SEATING PLANE
0.05
0.00
1.2±0.1
(0.2) TYP
6
5
8X 0.5
2X
2
2±0.1
1
10
10X
PIN 1 ID
(OPTIONAL)
10X
0.5
0.4
0.3
0.2
0.1
0.05
C A
C
B
4214926/A 07/2014
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. The package thermal pad must be soldered to the printed circuit board for thermal and mechanical performance.
www.ti.com
EXAMPLE BOARD LAYOUT
DSC0010B
WSON - 0.8 mm max height
PLASTIC SMALL OUTLINE - NO LEAD
(1.2)
10X (0.65)
SYMM
10
1
10X (0.25)
SYMM
(2)
(0.75) TYP
8X (0.5)
5
( 0.2) TYP
VIA
6
(0.35) TYP
(2.75)
LAND PATTERN EXAMPLE
SCALE:20X
0.07 MIN
ALL AROUND
0.07 MAX
ALL AROUND
SOLDER MASK
OPENING
METAL
SOLDER MASK
OPENING
NON SOLDER MASK
DEFINED
(PREFERRED)
METAL
UNDER
SOLDER MASK
SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4214926/A 07/2014
NOTES: (continued)
4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature
number SLUA271 (www.ti.com/lit/slua271).
www.ti.com
EXAMPLE STENCIL DESIGN
DSC0010B
WSON - 0.8 mm max height
PLASTIC SMALL OUTLINE - NO LEAD
10X (0.65)
SYMM
METAL
TYP
10X (0.25)
(0.55)
SYMM
(0.89)
8X (0.5)
(1.13)
(2.75)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
EXPOSED PAD
84% PRINTED SOLDER COVERAGE BY AREA
SCALE:25X
4214926/A 07/2014
NOTES: (continued)
5. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated