LM22680 2A SIMPLE SWITCHER®, Step-Down Voltage Regulator with Features General Description Features The LM22680 series of regulators are monolithic integrated circuits which provide all of the active functions for a stepdown (buck) switching regulator capable of driving up to 2A loads with excellent line and load regulation characteristics. High efficiency (>90%) is obtained through the use of a low ON-resistance N-channel MOSFET. The SIMPLE SWITCHER® concept provides for an easy to use complete design using a minimum number of external components and National’s WEBENCH® design tool. National’s WEBENCH® tool includes features such as external component calculation, electrical simulation, thermal simulation, and Build-It boards for easy design-in. The switching clock frequency is provided by an internal fixed frequency oscillator which operates at 500 kHz. The switching frequency can also be adjusted with an external resistor or synchronized to an external clock up to 1MHz. It is also possible to selfsynchronize multiple regulators to share the same switching frequency. The LM22680 series also has built in thermal shutdown, current limiting and an enable control input that can power down the regulator to a low 25 µA quiescent current standby condition. An adjustable soft-start feature is provided by selecting an appropriate external soft-start capacitor. ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Wide input voltage range: 4.5V to 42V Internally compensated voltage mode control Stable with low ESR ceramic capacitors 200 mΩ N-channel MOSFET Output voltage option: -ADJ (outputs as low as 1.285V) ±1.5% feedback reference accuracy Switching frequency of 500 kHz, adjustable between 200 kHz and 1 MHz -40°C to 125°C operating junction temperature range Precision enable pin Integrated boot diode Adjustable soft-start Fully WEBENCH® enabled Step-down and inverting buck-boost applications Package ■ PSOP-8 (Exposed Pad) Applications ■ ■ ■ ■ ■ Industrial Control Telecom and Datacom Systems Embedded Systems Automotive Telematics and Body Electronics Conversions from Standard 24V, 12V and 5V Input Rails Simplified Application Schematic 30080701 © 2008 National Semiconductor Corporation 300807 www.national.com LM22680 2A SIMPLE SWITCHER®, Step-Down Voltage Regulator with Features December 12, 2008 LM22680 Connection Diagram 30080740 8-Lead Plastic PSOP-8 Package NS Package Number MRA08B Ordering Information Output Voltage Order Number ADJ LM22680MR-ADJ ADJ LM22680MRE-ADJ ADJ LM22680MRX-ADJ Package Type NSC Package Drawing Supplied As 95 Units in Rails PSOP-8 Exposed Pad MRA08B 250 Units in Tape and Reel 2500 Units in Tape and Reel Pin Descriptions Pin Name Description Application Information 1 BOOT Bootstrap input Provides the gate voltage for the high side NFET. 2 SS Soft-start pin An external capacitor and an internal 50 µA current source set the time constant for the rise of the error amplifier reference. Pin can be left floating and internal soft-start will be default. 3 4 RT/SYNC Oscillator frequency adjust pin or frequency synchronization A resistor connected from this pin to GND adjusts the oscillator frequency. This pin can also accept an input for synchronization from an external clock. Pin can be left floating and internal setting will be default to 500 kHz. FB Feedback pin Inverting input to the internal voltage error amplifier. 5 EN Precision enable pin When pulled low regulator turns off. 6 GND System ground Provide good capacitive decoupling between VIN and this pin. 7 VIN Source input voltage Input to the regulator. Operates from 4.5V to 42V. 8 SW Switch pin Attaches to the switch node. www.national.com 2 If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. VIN to GND EN Pin Voltage SS, RT/SYNC Pin Voltage SW to GND (Note 2) BOOT Pin Voltage FB Pin Voltage Power Dissipation 43V -0.5V to 6V -0.5V to 7V -5V to VIN VSW + 7V -0.5V to 7V Internally Limited 150°C 260°C ±2 kV -65°C to +150°C Operating Ratings (Note 1) Supply Voltage (VIN) Junction Temperature Range 4.5V to 42V -40°C to +125°C Electrical Characteristics Limits in standard type are for TJ = 25°C only; limits in boldface type apply over the junction temperature (TJ) range of -40°C to +125°C. Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TA = TJ = 25°C, and are provided for reference purposes only. Unless otherwise specified: VIN = 12V. Symbol Parameter Conditions VFB Feedback Voltage VIN = 4.7V to 42V IQ Quiescent Current VFB = 5V Standby Quiescent Current EN Pin = 0V ISTDBY ICL Current Limit IL Output Leakage Current RDS(ON) fO Min (Note 5) Typ (Note 4) Max (Note 5) Units 1.266/1.259 1.285 1.304/1.311 V 3.4 6 mA 25 40 µA 2.8 3.4 A VIN = 42V, EN Pin = 0V, VSW = 0V 0.2 2 µA VSW = -1V 0.1 3 µA 0.2 0.24/0.32 Ω 500 600 kHz 2.32 Switch On-Resistance Oscillator Frequency TOFFMIN Minimum Off-time TONMIN Minimum On-time 400 300 IBIAS Feedback Bias Current VEN Enable Threshold Voltage IEN Enable Input Current EN Input = 0V FSYNC Synchronization Frequency VSYNC = 3.5V, 50% duty-cycle VSYNC Synchronization Threshold Voltage ISS Soft-Start Current TSD Thermal Shutdown Threshold θJA Thermal Resistance VFB = 1.3V 1.3 30 MR Package, Junction to ambient temperature resistance (Note 6) 3 ns 100 ns 230 nA 1.6 1.9 V 6 µA 1 MHz 1.75 V 50 70 µA 150 °C 60 °C/W www.national.com LM22680 Junction Temperature Soldering Information Infrared (5 sec.) ESD Rating (Note 3) Human Body Model Storage Temperature Range Absolute Maximum Ratings (Note 1) LM22680 Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur, including inoperability and degradation of device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or other conditions beyond those indicated in the recommended Operating Ratings is not implied. The recommended Operating Ratings indicate conditions at which the device is functional and should not be operated beyond such conditions. Note 2: The absolute maximum specification of the ‘SW to GND’ applies to DC voltage. An extended negative voltage limit of -10V applies to a pulse of up to 50 ns. Note 3: ESD was applied using the human body model, a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin. Note 4: Typical values represent most likely parametric norms at the conditions specified and are not guaranteed. Note 5: Min and Max limits are 100% production tested at 25°C. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control (SQC) methods. Limits are used to calculate National’s Average Outgoing Quality Level (AOQL). Note 6: The value of θJA for the PSOP-8 exposed pad (MR) package of 60°C/W is valid if package is mounted to 1 square inch of copper. The θJA value can range from 42 to 115°C/W depending on the amount of PCB copper dedicated to heat transfer. Typical Performance Characteristics Unless otherwise specified the following conditions apply: Vin = 12V, TJ = 25°C. Efficiency vs IOUT and VIN VOUT = 3.3V, fO= 500 kHz Normalized Switching Frequency vs Temperature 30080704 30080727 Current Limit vs Temperature Normalized RDS(ON) vs Temperature 30080708 30080703 www.national.com 4 Normalized Enable Threshold Voltage vs Temperature 30080705 30080710 Standby Quiescent Current vs Input Voltage Normalized Feedback Voltage vs Temperature 30080707 30080706 Normalized Feedback Voltage vs Input Voltage Switching Frequency vs RT/SYNC Resistor 30080713 30080709 5 www.national.com LM22680 Feedback Bias Current vs Temperature LM22680 Soft-start Current vs Temperature 30080742 www.national.com 6 LM22680 Typical Application Circuit and Block Diagram 30080714 FIGURE 1. 3.3V VOUT, 2A at 600 kHz 7 www.national.com LM22680 Detailed Operating Description Minimum Duty-Cycle The LM22680 switching regulator features all of the functions necessary to implement an efficient high voltage buck regulator using a minimum of external components. This easy to use regulator integrates a 42V N-Channel switch with an output current capability of 2A. The regulator control method is based on voltage mode control with input voltage feed forward. The loop compensation is integrated into the LM22680 so that no external compensation components need to be selected or utilized. Voltage mode control offers short minimum on-times allowing short duty-cycles necessary in high input voltage applications. The operating frequency is fixed at 500 kHz to allow for small external components while avoiding excessive switching losses. The switching frequency can be adjusted with an external resistor from 200 kHz to 1 MHz or it can be synchronized to an external clock up to 1 MHz. The output voltage can be set as low as 1.285V. Fault protection features include current limiting, thermal shutdown and remote shutdown capability. The device is available in the PSOP-8 package featuring an exposed pad to aid thermal dissipation. The functional block diagram with typical application of the LM22680 are shown in Figure 1. Besides a minimum off-time, there is also a minimum on-time which will take effect when the output voltage is adjusted very low and the input voltage is very high. Should the operation require a shorter minimum on-time than the typical 100 ns, individual switching pulses will be skipped. where D is the duty-cycle. Current Limit When the power switch turns on, the slight capacitance loading of the Schottky diode, D1, causes a leading-edge current spike with an extended ringing period. This spike can cause the current limit comparator to trip prematurely. A leading edge blanking time (TBLK) of 110 ns (typical) is used to avoid sampling the spike. When the switch current reaches the current limit threshold, the switch is immediately turned off and the internal switching frequency is reduced. This extends the off time of the switch to prevent a steady state high current condition. As the switch current falls below the current limit threshold, the switch current will attempt to turn on. If a load fault continues, the switch will again exceed the threshold and turn off. This will result in a low duty-cycle pulsing of the power switch to minimize the overall fault condition power dissipation. The switching frequency will reduce (fold back) if the overload condition causes the output voltage to be 72.4% (typical) of the adjusted output voltage. The current limit will only protect the inductor from a runaway condition if the LM22680 is operating in its safe operating area. A runaway condition of the inductor is potentially catastrophic to the application. For every design, the safe operating area needs to be calculated. Factors in determining the safe operating area are the switching frequency, input voltage, output voltage, minimum on-time and feedback voltage during an over current condition. As a first pass check, if the following equation holds true, a given design is considered in a safe operating area and the current limit will protect the circuit: Precision Enable The precision enable pin (EN) can be used to shut down the power supply. Connecting this pin to ground or to a voltage less than typical 1.6V will completely turn off the regulator. The current drain from the input supply when off is typically 25 µA with 12V input voltage. The power consumed during this off state is mostly defined by an internal 2 MΩ resistor to VIN. The enable pin has an internal pull-up current source of approximately 6 µA. When driving the enable pin, the high voltage level for the on condition should not exceed the 6V absolute maximum limit. When enable control is not required, the EN pin should be left floating. The precision feature enables simple sequencing of multiple power supplies with a resistor divider from another power supply. Maximum Duty-Cycle / Dropout Voltage The typical maximum duty-cycle is 85% at 500 kHz switching frequency. This corresponds to a typical minimum off-time of 300 ns. When operating at switching frequencies higher than 500 kHz, the 300 ns minimum off-time results in a lower maximum duty-cycle limit than 85%. This forced off-time is important to provide enough time for the Cboot capacitor to charge during each cycle. The lowest input voltage required to maintain operation is: VIN x TBLK x F < VOUT x 0.724 If the equation above does not hold true, the following secondary equation will need to hold true to be in safe operating area: If both equations do not hold true, a particular design will not have an effective current limit function which might damage the circuit during startup, over current conditions, or steady state over current and short circuit condition. Oftentimes a reduction of the maximum input voltage or reduction of the switching frequency will bring a design into the safe operating area. When synchronized to an external sync pulse, the LM22680 will not fold back the switching frequency in an over current condition. Where VD is the forward voltage drop across the re-circulating Schottky diode and VQ is the voltage drop across the internal power N-FET of the LM22680. The RDS(ON) of the FET is specified in the electrical characteristics section of this datasheet to calculate VQ according to the FET current. F is the switching frequency. www.national.com 8 LM22680 Soft-Start The soft-start feature allows the regulator to gradually reach the initial steady state operating point, thus reducing start-up stresses and surges. The soft-start can be adjusted by selecting an external soft-start capacitor. An internal 50 µA current source charges up the external soft-start capacitor. The generated voltage is the voltage the internal reference limits. If no external soft-start capacitor is used, there is an internal soft-start feature with 500 µs (typical) start-up time. Recommended soft-start capacitor values are between 100 nF to 1 µF. Switching Frequency Setting and Synchronization There are three different modes for the RT/SYNC pin. It can be left floating for a 500 kHz switching frequency. A resistor from the RT/SYNC pin to ground can be used to adjust the switching frequency between 200 kHz and 1 MHz. An external synchronization pulse can be applied to the RT/ SYNC pin for switching frequencies up to 1 MHz. The LM22680 internally sets the RT/SYNC mode during start up. Many applications are limited to lower switching frequencies due to minimum on-time and minimum off-time requirements as well as increased switching losses at switching frequencies higher than 500 kHz. In case of synchronizing to an external sync pulse, the clock pulse must be in a valid low or high state when the LM22680 starts up and can be applied after device regulation. The internal oscillator will synchronize to the external sync pulse rising edge. If the external sync pulse is disconnected the LM22680 switching frequency will return to default 500 kHz (typ.). When operating at frequencies above 500 kHz, external components such as the inductor and the output capacitors cannot be reduced dramatically. This is due to the fixed internal compensation and stability requirements. Running the LM22680 at frequencies higher than 500 kHz is intended for applications with EMI or beat frequency concerns. The flexibility of increasing the switching frequency above 500 kHz can be used to operate outside a critical signal frequency band of an application. This can also be used to set multiple switchers in an application to the same frequency to reduce beat frequencies and simplify filtering. See the current limit section of this datasheet for information about the safe operating area. When synchronizing to an external synchronization pulse, the LM22680 will not fold back the switching frequency in an over current condition. The typical curve below shows adjusted switching frequencies with different frequency set resistors from the RT/SYNC pin to ground. 30080713 FIGURE 2. Switching Frequency vs RT/SYNC Resistor Self Synchronize It is also possible to self-synchronize multiple LM22680 regulators to share the same switching frequency. This can be done by attaching the RT/SYNC pins together and putting a 1 kΩ resistor to ground. The diagram in Figure 3 illustrates this setup. The two regulators will be clocked at the same frequency but slightly phase shifted according to the minimum off-time of the regulator with the fastest running oscillator. The slight phase shift helps to reduce the stress on the input capacitors of the power supply. 30080730 FIGURE 3. Self Synchronizing Setup Boot Pin The LM22680 integrates an N-Channel FET switch and associated floating high voltage level shift / gate driver. This gate driver circuit works in conjunction with an internal diode and an external bootstrap capacitor. A 0.01 µF ceramic capacitor connected with short traces between the BOOT pin and the SW pin is recommended to effectively drive the internal FET switch. During the off-time of the switch, the SW voltage is approximately -0.5V and the external bootstrap capacitor is charged from the internal supply through the internal bootstrap diode. When operating with a high PWM duty-cycle, the buck switch will be forced off each cycle to ensure that the bootstrap capacitor is recharged. See the maximum duty-cycle section for more details. 9 www.national.com LM22680 Inductor The inductor value is determined based on the load current, ripple current, and the minimum and maximum input voltage. To keep the application in continuous current conduction mode (CCM), the maximum ripple current, IRIPPLE , should be less than twice the minimum load current. The general rule of keeping the inductor current peak-to-peak ripple around 30% of the nominal output current is a good compromise between excessive output voltage ripple and excessive component size and cost. Using this value of ripple current, the value of inductor, L, is calculated using the following formula: Thermal Protection Internal Thermal Shutdown circuitry protects the LM22680 in the event the maximum junction temperature is exceeded. When activated, typically at 150°C, the regulator is forced into a low power reset state. There is a typical hysteresis of 15 degrees. Internal Compensation The LM22680 has internal compensation designed for a stable loop with a wide range of external power stage components. Insuring stability of a design with a specific power stage (inductor and output capacitor) can be tricky. The LM22680 stability can be verified over varying loads and input and output voltages using WEBENCH® Designer online circuit simulation tool at www.national.com. A quick start spreadsheet can also be downloaded from the online product folder. The typical location of the internal compensation poles and zeros as well as the DC gain is given in Table 1. The LM22680 has internal type III compensation allowing for the use of most output capacitors including ceramics. This information can be used to calculate the transfer function from the FB pin to the internal compensation node (input to the PWM comparator in the block diagram). where F is the switching frequency which is 500 kHz without an external frequency set resistor or external sync signal applied to the RT/SYNC pin. If the switching frequency is set higher than 500kHz, the inductance value may not be reduced accordingly due to stability requirements. The internal compensation is optimized for circuits with a 500 kHz switching frequency. See the internal compensation section for more details. This procedure provides a guide to select the value of the inductor L. The nearest standard value will then be used in the circuit. Increasing the inductance will generally slow down the transient response but reduce the output voltage ripple amplitude. Reducing the inductance will generally improve the transient response but increase the output voltage ripple. The inductor must be rated for the peak current, IPK+, to prevent saturation. During normal loading conditions, the peak current occurs at maximum load current plus maximum ripple. Under an overload condition as well as during load transients, the peak current is limited to 2.8A typical (3.4A maximum). This requires that the inductor be selected such that it can run at the maximum current limit and not only the steady state current. Depending on inductor manufacturer, the saturation rating is defined as the current necessary for the inductance to reduce by 30% at 20°C. In typical designs the inductor will run at higher temperatures. If the inductor is not rated for enough current, it might saturate and due to the propagation delay of the current limit circuitry, the power supply may get damaged. TABLE 1. Corners Frequency Pole 1 150 kHz Pole 2 250 kHz Pole 3 100 Hz Zero 1 1.5 kHz Zero 2 15 kHz DC gain 37.5 dB For the power stage transfer function the standard voltage mode formulas for the double pole and the ESR zero apply: Input Capacitor Good quality input capacitors are necessary to limit the ripple voltage at the VIN pin while supplying most of the switch current during on-time. When the switch turns on, the current into the VIN pin steps to the peak value, then drops to zero at turnoff. The average current into VIN during switch on-time is the load current. The input capacitance should be selected for RMS current, IRMS, and minimum ripple voltage. A good approximation for the required ripple current rating necessary is IRMS > IOUT / 2. Quality ceramic capacitors with a low ESR should be selected for the input filter. To allow for capacitor tolerances and voltage effects, multiple capacitors may be used in parallel. If step input voltage transients are expected near the maximum rating of the LM22680, a careful evaluation of ringing and possible voltage spikes at the VIN pin should be completed. An additional damping network or input voltage clamp may be required in these cases. Usually putting a higher ESR electrolytic input capacitor in parallel to the low ESR bypass capacitor will help to reduce The peak ramp level of the oscillator signal feeding into the PWM comparator is VIN/10 which equals a gain of 20dB of this modulator stage of the IC. The LM22680 has a compensation tranfer function gain of 37.5dB. Generally, calculation as well as simulation can only aid in selecting good power stage components. A good design practice is to test for stability with load transient tests or loop measurement tests. Application note AN-1889 shows how to easily perform a loop transfer function measurement with only an oscilloscope and a function generator. Application Information EXTERNAL COMPONENTS The following design procedures can be used to design a nonsynchronous buck converter with the LM22680. www.national.com 10 LM22680 excessive voltages during a line transient and will also move the resonance frequency of the input filter away from the regulator bandwidth. Output Capacitor The output capacitor can limit the output ripple voltage and provide a source of charge for transient loading conditions. Multiple capacitors can be placed in parallel. Very low ESR capacitors such as ceramic capacitors reduce the output ripple voltage and noise spikes, while larger higher ESR capacitors in parallel provide large bulk capacitance for transient loading conditions. An approximation for the output voltage ripple is: 30080723 FIGURE 4. Resistive Feedback Divider A maximum value of 10 kΩ is recommended for the sum of R1 and R2 to keep high output voltage accuracy. At loads less than 5 mA, the boot capacitor will not hold enough charge to power the internal high side driver. The output voltage may droop until the boot capacitor is recharged. Selecting a total feedback resistance to be below 3 kΩ will provide some minimal load and can keep the output voltage from collapsing in such low load conditions. where ΔIL is the inductor ripple current. If the switching frequency is set higher than 500 kHz, the capacitance value may not be reduced accordingly due to stability requirements. The internal compensation is optimized for circuits with a 500 kHz switching frequency. See the internal compensation section for more details. Catch Diode A Schottky type re-circulating diode is required for all LM22680 applications. Ultra-fast diodes which are not Schottky diodes are not recommended and may result in damage to the IC due to reverse recovery current transients. The near ideal reverse recovery characteristics and low forward voltage drop of Schottky diodes are particularly important diode characteristics for high input voltage and low output voltage applications common to the LM22680. The reverse recovery characteristic determines how long the current surge lasts each cycle when the N-channel MOSFET is turned on. The reverse recovery characteristics of Schottky diodes minimizes the peak instantaneous power in the switch occurring during turn-on for each cycle. The resulting switching losses are significantly reduced when using a Schottky diode. The reverse breakdown rating should be selected for the maximum VIN, plus some safety margin. A rule of thumb is to select a diode with the reverse voltage rating of 1.3 times the maximum input voltage. The forward voltage drop has a significant impact on the conversion efficiency, especially for applications with a low output voltage. ‘Rated’ current for diodes varies widely from various manufacturers. The worst case is to assume a short circuit load condition. In this case the diode will carry the output current almost continuously. For the LM22680 this current can be as high as 2.8A (typical). Assuming a worst case 1V drop across the diode, the maximum diode power dissipation can be as high as 2.8W. Cboot Capacitor The bootstrap capacitor between the BOOT pin and the SW pin supplies the gate current to turn on the N-channel MOSFET. The recommended value of this capacitor is 10 nF and should be a good quality, low ESR ceramic capacitor. It is possible to put a small resistor in series with the Cboot capacitor to slow down the turn-on transition time of the internal N-channel MOSFET. Resistors in the range of 10Ω to 50Ω can slow down the transition time. This can reduce EMI of a switched mode power supply circuit. Using such a series resistor is not recommended for every design since it will increase the switching losses of the application and makes thermal considerations more challenging. Resistor Divider For the LM22680 no resistor divider is required for 1.285V output voltage. The output voltage should be directly connected to the FB pin. Other output voltages can use a resistor divider. The resistor values can be determined by the following equations: -5.0 option: Circuit Board Layout Board layout is critical for switching power supplies. First, the ground plane area must be sufficient for thermal dissipation purposes. Second, appropriate guidelines must be followed to reduce the effects of switching noise. Switch mode converters are very fast switching devices. In such devices, the rapid increase of input current combined with the parasitic trace inductance generates unwanted L di/dt noise spikes. The magnitude of this noise tends to increase as the output current increases. This parasitic spike noise may turn into electromagnetic interference (EMI) and can also cause problems in device performance. Therefore, care must be taken in layout to minimize the effect of this switching noise. Where VFB = 1.285V typical. 11 www.national.com LM22680 The most important layout rule is to keep the AC current loops as small as possible. Figure 5 shows the current flow of a buck converter. The top schematic shows a dotted line which represents the current flow during the FET switch on-state. The middle schematic shows the current flow during the FET switch off-state. The bottom schematic shows the currents referred to as AC currents. These AC currents are the most critical since current is changing in very short time periods. The dotted lines of the bottom schematic are the traces to keep as short as possible. This will also yield a small loop area reducing the loop inductance. To avoid functional problems due to layout, review the PCB layout example. Best results are achieved if the placement of the LM22680, the bypass capacitor, the Schottky diode and the inductor are placed as shown in the example. It is also recommended to use 2oz copper boards or thicker to help thermal dissipation and to reduce the parasitic inductances of board traces. Thermal Considerations The two highest power dissipating components are the recirculating diode and the LM22680 regulator IC. The easiest method to determine the power dissipation within the LM22680 is to measure the total conversion losses (Pin – Pout) then subtract the power losses in the Schottky diode and output inductor. An approximation for the Schottky diode loss is: P = (1 - D) x IOUT x VD An approximation for the output inductor power is: P = IOUT2 x R x 1.1, where R is the DC resistance of the inductor and the 1.1 factor is an approximation for the AC losses. The regulator has an exposed thermal pad to aid power dissipation. Adding several vias under the device to the ground plane will greatly reduce the regulator junction temperature. Selecting a diode with an exposed pad will aid the power dissipation of the diode. The most significant variables that affect the power dissipated by the LM22680 are the output current, input voltage and operating frequency. The power dissipated while operating near the maximum output current and maximum input voltage can be appreciable. The junction-to-ambient thermal resistance of the LM22680 will vary with the application. The most significant variables are the area of copper in the PC board, the number of vias under the IC exposed pad and the amount of forced air cooling provided. The integrity of the solder connection from the IC exposed pad to the PC board is critical. Excessive voids will greatly diminish the thermal dissipation capacity. The junction-to-ambient thermal resistance of the LM22680 PSOP-8 package is specified in the electrical characteristics table under the applicable conditions. 30080724 FIGURE 5. Current Flow in a Buck Application www.national.com 12 LM22680 PCB Layout Example 30080741 13 www.national.com LM22680 Schematic for Buck/Boost (Inverting) Application See AN-1888 for more information on the inverting (buckboost) application generating a negative output voltage from a positive input voltage. 30080726 www.national.com 14 LM22680 Physical Dimensions inches (millimeters) unless otherwise noted 8-Lead Plastic PSOP-8 Package NS Package Number MRA08B 15 www.national.com LM22680 2A SIMPLE SWITCHER®, Step-Down Voltage Regulator with Features Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH® Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage Reference www.national.com/vref Design Made Easy www.national.com/easy PowerWise® Solutions www.national.com/powerwise Solutions www.national.com/solutions Serial Digital Interface (SDI) www.national.com/sdi Mil/Aero www.national.com/milaero Temperature Sensors www.national.com/tempsensors Solar Magic® www.national.com/solarmagic Wireless (PLL/VCO) www.national.com/wireless Analog University® www.national.com/AU THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2008 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: [email protected] German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: [email protected] National Semiconductor Japan Technical Support Center Email: [email protected]