深圳市腾恩科技有限公司 SHENZHEN TENAND TECHNOLOGY CO.,LTD http://www.tenand.com 深圳市腾恩科技有限公司 SHENZHEN TENAND TECHNOLOGY CO.,LTD http://www.tenand.com Note: 1.Year date code. 2. 2-digit work week. 3. Factory code shall be marked (Z : Taiwan, Y : Thailand). 4. All dimensions are in millimeters (inches). 5. Tolerance is 0.25mm (.010 ) unless otherwise noted. 6. Specifications are subject to change without notice. Ordering Information Part Number LTV-8141 LTV-8141M LTV-8141S LTV-8141S-TA LTV-8141S-TA1 LTV-8241 LTV-8241M LTV-8241S LTV-8241S-TA LTV-8241S-TA1 LTV-8441 LTV-8441M LTV-8441S LTV-8441S-TA LTV-8441S-TA1 LTV8141-V LTV8141M-V LTV8141S-V LTV8141STA-V LTV8141STA1-V LTV8241-V LTV8241M-V LTV8241S-V LTV8241STA-V LTV8241STA1-V LTV8441-V LTV8441M-V LTV8441S-V LTV8441STA-V LTV8441STA1-V 12-96 Package 4-pin DIP 4-pin (leads with 0.4" spacing) 4-pin (lead bends for surface mount) 4-pin (tape and reel packaging of type I) 4-pin (tape and reel packaging of type II) 8-pin DIP 8-pin (leads with 0.4" spacing) 8-pin (lead bends for surface mount) 8-pin (tape and reel packaging of type I) 8-pin (tape and reel packaging of type II) 16-pin DIP 16-pin (leads with 0.4" spacing) 16-pin (lead bends for surface mount) 16-pin (tape and reel packaging of type I) 16-pin (tape and reel packaging of type II) 4-pin DIP 4-pin (leads with 0.4" spacing) 4-pin (lead bends for surface mount) 4-pin (tape and reel packaging of type I) 4-pin (tape and reel packaging of type II) 8-pin DIP 8-pin (leads with 0.4" spacing) 8-pin (lead bends for surface mount) 8-pin (tape and reel packaging of type I) 8-pin (tape and reel packaging of type II) 16-pin DIP 16-pin (leads with 0.4" spacing) 16-pin (lead bends for surface mount) 16-pin (tape and reel packaging of type I) 16-pin (tape and reel packaging of type II) Safety Standard Approval UL approved TUV approved CSA approved FIMKO approved NEMKO approved SEMKO approved DEMKO approved Application part number LTV-8141 LTV-8241 LTV-8441 VDE approved LTV-8141 LTV-8241 LTV-8441 Absolute Maximum Ratings (Ta=25 ) Parameter Input Output Symbol Rating Unit Forward Current IF Power Dissipation P 70 mW Collector-Emitter Voltage V CEO 35 V Emitter-Collector Voltage V ECO 6 V IC 80 mA Collector Current 50 mA PC 150 mW Total Power Dissipation P tot 200 mW Operating Temperature Topr -30~+100 Tstg -55~+125 Collector Power Dissipation Storage Temperature *1.Isolation Voltage V iso 5 *2.Soldering Temperature Tsol 260 KV rms *1. AC for 1 minute, R.H. = 40 ~ 60% Isolation voltage shall be measured using the following method. (1)Short between anode and cathode on the primary side and between collector, emitter and base on the secondary side. (2)The isolation voltage tester with zero-cross circuit shall be used. (3)The waveform of applied volttage shall be a sine wave. *2. For 10 seconds. Electrical/Optical Characteristics Symbol Min. Typ. Max. Unit 1.4 V I F= 250 pF V=0, f=1KHz VF 1.2 Terminal Capacitance Ct 50 Collector Dark Current Collector-Emitter Breakdown Voltage Emitter-Collector Breakdown Voltage Collector Current I CEO *Current Transfer Ratio Collector-emitter Saturation Voltage Isolation Resistance BV CEO 35 BV ECO 6 IC 6 75 CTR 600 7,500 V CE(sat) R ISO A 1 0.8 50 1.0 100 1.0 I C=0.1mA V I E=10 mA % V 1mA V CE =2V I F= 20mA, I C =5mA pF V=0, f=1MHz V CE =5V, I C =2mA R L=100 , -3dB V CE =2V, I C =10mA R L=100 fc Response Time (Rise) tr 60 300 s Response Time (Fall) tf 53 250 s IC *CTR= IF I F= DC500V, 40~60% R.H. Cut-off Frequency 6 A G Cf 1 V CE =10V V Floating Capacitance 0.6 Conditions 20mA KHz PHOTOCOUPLER Transfer Characteristics Output Input Parameter Forward Voltage (Ta=25 ) 100% 12-97 Typical Electrical/Optical Characteristic Curves (25 Ambient Temperature Unless Otherwise Noted) 12-98 12-99 PHOTOCOUPLER This datasheet has been downloaded from: www.DatasheetCatalog.com Datasheets for electronic components.