CLARE MXHV9910BETR Off-line, high brightness led driver Datasheet

MXHV9910
Off-Line, High Brightness LED Driver
Features
Description
• 8VDC to 450VDC Input Voltage Range
• >90% Efficiency
• Drives Multiple LEDs in Series/Parallel
Combinations
• Regulated LED Drive Current
• Linear or PWM Brightness Control
• Resistor-Programmable Oscillator Frequency
• RoHS Compliant
The MXHV9910 is a low-cost, high-brightness (HB)
LED driver manufactured using Clare’s high-voltage
BCDMOS on SOI process. This driver has internal
circuitry that allows it to operate from a universal AC
line or from 8VDC to 450VDC. This highly versatile
input operating voltage enables this IC to be used in a
broad range of HB LED applications.
The driver features a fixed-frequency, peak-current
control method, which provides an ideal solution for
driving multiple LEDs in series and in parallel. In
addition, LED dimming can be implemented by
applying a small DC voltage to the LD pin, or by
applying a low-frequency digital PWM signal to the
PWMD pin.
Applications
• Flat-Panel Display RGB Backlighting
• Signage and Decorative LED Lighting
• DC/DC or AC/DC LED Driver Applications
The MXHV9910 is available in a standard 8-lead SOIC
package and a thermally enhanced 8-lead SOIC
package with an Exposed Thermal Pad (EP)
Ordering Information
Part
Pb
MXHV9910B
MXHV9910BTR
e3
RoHS
2002/95/EC
MXHV9910BE
MXHV9910BETR
Description
SOIC-8 (100/Tube)
SOIC-8 Tape & Reel (2000/Reel)
SOIC-8 EP (100/Tube)
With Exposed Thermal Pad
SOIC-8 EP Tape & Reel (2000/Reel)
With Exposed Thermal Pad
Block Diagram
VDD
VIN
6
1
Voltage
Regulator
Voltage
Reference
250mV
RT
8
OSC
+
LD
7
PWM
Control
4
GATE
2
CS
+
PWMD
GND
DS-MXHV9910-R01
5
3
www.clare.com
1
MXHV9910
1
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1 Package Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2 Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4 Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.5 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.6 Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
3
3
3
4
4
4
2
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2 LED Driver Theory of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.1 Input Voltage Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.2 Current Sense Resistor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.3 Current Sense Blanking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.4 Enable/Disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.5 Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.6 Inductor Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.7 Gate Output Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.8 Linear Dimming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.9 PWM Dimming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.10 Combination Linear and PWM Dimming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
5
5
6
6
7
7
7
7
8
8
8
9
3
Manufacturing Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1 Mechanical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2 Packaging Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.1 Tape & Reel Information for both 8-Pin Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3 Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4 Washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
R01
www.clare.com
10
10
11
11
11
11
2
MXHV9910
1. Specifications
1.1 Package Pinout
1.2 Pin Description
Pin#
Name
1
VIN
2
CS
VIN
1
8
RT
CS
2
7
LD
3
4
GND
GATE
GND
3
6
VDD
5
PWMD
GATE
4
5
PWMD
6
VDD
7
LD
8
RT
EP
-
Description
Input voltage
LED Current Sense input. Internal current
sense threshold is set at 250mV. The external
sense resistor sets the maximum LED current.
Device Ground
External MOSFET gate driver output
Low-frequency PWM dimming control input with
internal pull-down resistor.
Regulated supply voltage output. Requires a
storage capacitor to GND. Can be overdriven by
external voltage applied to VDD.
Linear Dimming. Apply a voltage less than
VCS(high) to dim the LED(s).
Resistor to GND sets the oscillator/primary
PWM frequency.
Electrical and thermal conductive pad on the
bottom of the MXHV9910BE. Connect this pad
to ground, and provide sufficient thermal
coupling to remove heat from the package.
1.3 Absolute Maximum Ratings
Parameter
Input Voltage to GND
Inputs & Outputs Voltage to GND
VDD , Externally Applied
Symbol
Maximum
Unit
VIN
-0.5 to +460
V
CS, LD, PWMD, GATE
-0.3 to VDD+0.3
V
VDD.EXT
15
V
2.5
W
Power Dissipation
SOIC-8 With Thermal Tab
SOIC-8 W/O Thermal Tab
PD
0.975
W
TJmax
150
°C
Operating Temperature
TA
-40 to +85
°C
Junction Temperature (Operating)
TJ
-40 to +150
°C
TSTG
-55 to +150
°C
Maximum Junction Temperature
Storage Temperature
Electrical absolute maximum ratings are at 25°C.
Absolute maximum ratings are stress ratings. Stresses in
excess of these ratings can cause permanent damage to
the device. Functional operation of the device at conditions
beyond those indicated in the operational sections of this
data sheet is not implied.
R01
www.clare.com
3
MXHV9910
1.4 Recommended Operating Conditions
Parameter
Input Voltage Range
PWMD Frequency
Operating Temperature
Symbol
VIN
fPWMD
TA
Minimum
Nominal
Maximum
8
-40
500
-
450
+85
Unit
VDC
Hz
°C
1.5 Electrical Characteristics
Unless otherwise specified, all electrical specifications are provided for TA=25°C.
Parameter
Input
Input DC Voltage Range
Shut-Down Mode Supply Current
Maximum Voltage to VDD Pin
Regulator
Conditions
Symbol
Minimum
Typical
Maximum
Unit
DC Input Voltage
PWMD to GND, VIN=15 to 450V
External Voltage applied to VDD Pin
VIN
IINSD
VDDmax
8
-
0.3
-
450
0.6
12
VDC
VIN=15V to 450V,
IDD(ext)=0,
GATE Output=Open
VDD
7.2
7.8
8.4
VDC
-
IDD(ext)
-
-
2
mA
VIN=15V, IL=1mA
ΔVDD
-
-
200
mV
VIN=8V to 450V
VIN=8V to 450V
VIN=12V, VPWMD=VDD
VEN(low)
VEN(high)
REN
2.4
70
115
0.5
150
CS=0V
CS=VDD
-40°C < TA < 85°C
RT=400kΩ
RT=400kΩ
IIL
IIH
VCS(high)
tBLANK
tDELAY
200
-
-45
0
400
300
-90
±15
280
-
mV
ns
ns
RT=400kΩ
fS
51
64
77
kHz
IOUT= -10mA
IOUT=10mA
CGATE=500pF
CGATE=500pF
VGATE(hi)
VGATE(lo)
tRISE
tFALL
VDD-0.3
-
0.03
16
7
0.3
-
Symbol
Minimum
Typical
Maximum
Unit
RθJA
-
50
128
-
°C/W
Internal Voltage Regulator
VDD Current Available
for External Circuitry
VDD Load Regulation
PWM Dimming
PWMD Input Low Voltage
PWMD Input High Voltage
PWMD Pull-Down Resistance
Current Sense Comparator
Current Sense (CS) Input Current
CS Low
CS High
Current Sense Threshold Voltage
Current Sense Blanking Interval
Delay from CS Trip to Gate Low
Oscillator
Oscillator Frequency (Gate Driver)
Gate Driver
Gate High Output Voltage
Gate Low Output Voltage
Gate Output Rise Time
Gate Output Fall Time
mA
V
V
kΩ
μA
V
ns
1.6 Thermal Characteristics
Parameter
Thermal Resistance,
Junction-to-Ambient
1
4
Package
SOIC-8 With Thermal Pad (BE) 1
SOIC-8 W/O Thermal Pad (B)
Use of a four-layer PCB can improve thermal dissipation (reference EIA/JEDEC JESD51-5).
www.clare.com
R01
MXHV9910
2. Functional Description
Figure 1 Typical Application Circuit
8-450V
VDD
6
VDD
1
VIN
Voltage
Regulator
Voltage
Reference
250mV
8
RT
OSC
+
7
LD
PWM
Control
GATE
4
CS
2
+
5
PWMD
3
GND
RSENSE
2.1 Overview
The MXHV9910 is a high-efficiency, low cost, off-line
LED driver designed using Clare's state of the art
BCDMOS on SOI process. The driver can operate
from a DC supply voltage between 8 to 450VDC . The
versatile input supply voltage range enables this driver
to be used in a broad range of applications such as flat
panel display RGB backlighting, signage, decorative
LED lighting, and incandescent lamp replacement.
The MXHV9910 IC is configured in a buck converter
topology, which is a perfect choice for off-line and DC
applications driving multiple LEDs in series or parallel.
This method provides excellent efficiency and enables
a buck switcher design using a minimum number of
external components. An external current sense
resistor sets the peak current to the LED string. In
addition, LED dimming can be implemented by either
applying a DC control voltage to the LD pin, or by
applying a low frequency, pulse-width modulated
digital signal to the PWMD pin (typically 500 Hz).
located at the CS pin. When the rising voltage at the
current sense, CS, pin exceeds VCS(high), the internally
set threshold, the gate drive signal goes low and turns
off the external power MOSFET. Turning the power
MOSFET off causes the inductor current to decay until
the next rising edge of the clock, and the process
repeats.
The peak current threshold is set by comparing the
voltage developed across the RSENSE resistor to the
internal threshold, VCS(high). This default threshold can
be overridden externally by applying a voltage less
than VCS(high) to the LD pin. The lower of these two
thresholds limits the peak current in the inductor
A soft-start function can be implemented by slowly
ramping up the DC voltage at the LD pin from 0mV to
a level greater than 250mV. Figure 2 shows a typical
recommended soft-start circuit design.
Figure 2 Soft-Start RC Network
51kΩ
MXHV9910
2.2 LED Driver Theory of Operation
The gate driver pulse width mode (PWM) control
circuit is enabled by connecting the PWMD pin to the
VDD pin. When enabled, the rising edge of each
internal clock turns on the gate driver and the external
power MOSFET, causing the inductor current to ramp
up the voltage across the current sense resistor
R01
www.clare.com
VIN
CS
GND
GATE
RT
LD
VDD
PWMD
2kΩ
0.1μF
5
MXHV9910
Figure 3 MXHV9910 Waveforms (From Application Circuit in Figure 6)
Time Scale: 5μs/div
CH1:
50mA/div
FS 65kHz
Max 77mA
CH2:
10V/div
CH3:
5mV/div x 10
2.2.1 Input Voltage Regulator
The MXHV9910 has an internal voltage regulator that
can work with input voltages ranging from 12VDC to
450 VDC. When the input voltage applied at the VIN pin
is greater than 12VDC , the internal voltage regulator
regulates this voltage down to a typical 7.8V. The VDD
pin is the internal regulator output pin and must be
bypassed by a low ESR capacitor, typically 0.1μF, to
provide a low impedance path for high frequency
switching noise.
The MXHV9910 driver does not require the bulky
start-up resistors typically needed for off-line
controllers. An internal voltage regulator provides
sufficient voltage and current to power the internal IC
circuits. This voltage is also available at the VDD pin,
and can be used as bias voltage for external circuitry.
The internal voltage regulator can by bypassed by
applying an external DC voltage to the VDD pin that is
slightly higher than the internal regulator’s maximum
output voltage. This feature reduces power dissipation
of the integrated circuit and is more suitable in isolated
applications where an auxiliary transformer winding
could be used to supply VDD .
The total input current drawn by the VIN pin is equal to
the integrated circuit quiescent current, which is
0.6mA maximum, plus the gate driver current. The
gate driver current is dependant on the switching
frequency and the gate charge of the external power
MOSFET.
The following equation can be used to approximate
the VIN input current:
I IN ≈ 0.6mA + ( Q GATE × f S )
Where QGATE is the total gate charge of the external
power MOSFET, and fS is the switching oscillator
frequency.
2.2.2 Current Sense Resistor
The peak LED current is set by an external current
sense resistor connected from the CS pin to ground.
The value of the current sense resistor is calculated
based on the desired average LED current, the current
sense threshold, and the inductor ripple current.
The inductor is typically selected to be large enough to
keep the ripple current (the peak-to-peak difference in
the inductor current waveform) to less than 30% of the
average LED current. Factoring in this ripple current
requirement, the current sense resistor can be
determined by:
V csth
R sense = ------------------------------------------------------------[ 1 + ( 0.5 × r iout ) ] × I LED
Where:
• Vcsth = nominal current sense threshold = 0.25V
• riout = inductor ripple = 0.3
• ILED = average LED current
The power dissipation rating of the sense resistor can
be found with the following formula:
2
P = I LED × R sense
6
www.clare.com
R01
MXHV9910
It is a good practice to select a power rating that is at
least twice the calculated value. This will give proper
margins, and make the design more reliable.
Figure 4 Resistor Selection
Oscillator Frequency, fS, vs. RT
(TA=27ºC)
250
2.2.3 Current Sense Blanking
2.2.4 Enable/Disable
Connecting the PWMD pin to VDD enables the gate
driver. Connecting PWMD to GND disables the gate
driver and sets the device into the shut-down mode. In
the shut-down mode, the gate output drive is disabled
while all other functions remain active. The maximum
quiescent current in the shut-down mode is 0.6mA.
200
Frequency (kHz)
The MXHV9910 has an internal current-sense
blanking circuit. When the power MOSFET is turned
on, the external inductor can cause an undesired
spike at the current sense pin, CS, initiating a
premature termination of the gate pulse. To avoid this
condition, a typical 400ns internal leading edge
blanking time is implemented. This internal feature
eliminates the need for external RC filtering, thus
simplifying the design. During the current sense
blanking time, the current limit comparator is disabled,
preventing the gate-drive circuit from terminating the
gate-drive signal.
150
100
50
0
0
The typical off-line LED driver switching frequency, fS,
is between 30kHz and 120kHz. This operating range
gives designers a reasonable compromise between
switching losses and inductor size. The internal RC
oscillator has a frequency accuracy of ±20%. Figure 4
shows the RT resistor selection for the desired fS.
400
600
800
1000
1200
RT (kΩ)
2.2.6 Inductor Design
The inductor value is determined based on LED ripple
current, maximum on-time, the forward voltage drop of
all LEDs in a string at the desired current, and the
minimum input voltage, which is based on design
requirements. The maximum on-time is determined by
the duty cycle and switching frequency. The maximum
duty cycle is given by:
V LEDstring
D max = -------------------------V in
2.2.5 Oscillator
The MXHV9910 operates in a constant frequency
mode. Setting the oscillator frequency is achieved by
connecting an external resistor between RT and GND.
In general, switching frequency selection is based on
the inductor size, controller power dissipation, and the
input filter capacitor.
200
Where:
• VLEDstring is the LED string voltage at desired
average LED current.
• Vin is the minimum input voltage to VIN
The maximum duty cycle must be restricted to less
than 50% in order to prevent sub-harmonic oscillations
and open loop instability.
The converter maximum ON-time is given by:
D max
t ONmax = ------------fs
Where fs is the switching frequency of the internal
oscillator.
The inductor value for the given ripple is:
( V in – V LEDstring ) × t ONmax
L min = --------------------------------------------------------------------r iout × I LED
R01
www.clare.com
7
MXHV9910
2.2.8 Linear Dimming
The inductor peak current rating is given by:
A linear dimming function can be implemented by
applying a DC control voltage to the LD pin. By varying
this voltage, the user can adjust the current level in the
LEDs, which in turn will increase or decrease the light
intensity. The control voltage to the LD pin can be
generated from an external voltage divider network
from VDD . This function is useful if the user requires a
LED current at a particular level and there is no exact
Rsense value available. Note that applying a voltage
higher than the current sense threshold voltage at the
LD pin will not change the output current due to the
fixed threshold setting. When the LD pin is not used, it
should be connected to VDD .
I Lmax = I LED × [ 1 + ( 0.5 × r iout ) ]
2.2.7 Gate Output Drive
The MXHV9910 uses an internal gate drive circuit to
turn on and off an external power MOSFET. The gate
driver can drive a variety of MOSFETs. For a typical
off-line application, the total MOSFET gate charge will
be less than 25nC.
Figure 5 Typical Linear Dimming Application Circuit
Fuse F2
2A
LD
Monitor
BR1
AC
AC
AC Input
90 - 265Vrms
+
D1
BYV26B
NTC1
R1
402kΩ
C1
22μF
400V
C1
0.1μF
400V
VIN
CS
GND
GATE
L1
4.7mH
HB LEDs
350mA
R2
51kΩ
MXHV9910
RT
LD
VDD
PWMD
RA1
5.0kΩ
IXTA8N50P
C1
2.2μF
16V
R4
0.56Ω
C1
0.1μF
25V
2.2.9 PWM Dimming
The signal can be generated by a microcontroller or a
pulse generator with a duty cycle proportional to the
amount of desired light output. When PWMD is low,
gate drive is off; when PWMD is high, gate drive is
enabled.
Pulse width modulation dimming can be implemented
by driving the PWMD pin with a low frequency square
wave signal in the range of a few hundred Hertz. The
PWMD signal controls the LED brightness by gating
the PWM gate driver output pin GATE.
Figure 6 Buck Driver for PWM Dimming Application Circuit
VIN
12 - 30VDC
D1 Schottky
40V
10μF
50V
Q1
220μH
HB LEDs
900mA Max
ASMT-Mx00
MXHV9910
VIN
CS
GND
GATE
402kΩ
RT
LD
VDD
PWMD
CPC1001N*
R1
0.27Ω
0.1μF
50V
PWM
*Optional Isolation
8
www.clare.com
R01
MXHV9910
2.2.10 Combination Linear and PWM Dimming
A combination of linear and PWM dimming techniques
can be used to achieve a large dimming ratio.
Note: The output current will not go to zero if the LD
pin is pulled to GND because the minimum gate driver
on-time is equal to the current sense blanking interval.
To achieve zero LED current, the PWMD pin should be
used.
R01
www.clare.com
9
MXHV9910
3. Manufacturing Information
3.1 Mechanical Dimensions
8-Pin SOIC Package
Recommended PCB Land Pattern
0.19 - 0.25
(0.008 - 0.010)
5.80 - 6.20
(0.23 - 0.24)
1.55
(0.061)
0.40 - 1.27
(0.016 - 0.050)
3.80 - 4.00
(0.15 - 0.16)
5.40
(0.213)
PIN 1
0.33 - 0.51
(0.013 - 0.020)
1.27 TYP
(0.05 TYP)
0.60
(0.024)
4.80 - 5.00
(0.19 - 0.20)
1.27
(0.050)
0.10 - 0.25
(0.004 - 0.010)
0.394 - 0.648
(0.016 - 0.026)
Dimensions
mm
(inches)
1.35 - 1.75
(0.053 - 0.069)
8-Pin SOIC Package with Exposed Thermal Pad
Recommended PCB Land Pattern
0.19 - 0.25
(0.008 - 0.010)
5.80 - 6.20
(0.23 - 0.24)
3.80 - 4.00
(0.15 - 0.16)
1.55
(0.061)
0.40 - 1.27
(0.016 - 0.050)
2.40
(0.09)
PIN 1
0.33 - 0.51
(0.013 - 0.020)
2.40
(0.09)
5.40
(0.213)
1.27 TYP
(0.05 TYP)
2.032 - 2.413
(0.080 - 0.095)
0.60
(0.024)
1.27
(0.050)
4.80 - 5.00
(0.19 - 0.20)
0.00 - 0.13
(0.000 - 0.005)
0.394 - 0.648
(0.016 - 0.026)
1.35 - 1.75
(0.053 - 0.069)
2.032 - 2.413
(0.080 - 0.095)
Dimensions
mm
(inches)
Note: Thermal pad should be electrically connected to GND, pin 3.
10
www.clare.com
R01
MXHV9910
3.2 Packaging Information
3.2.1 Tape & Reel Information for both 8-Pin Packages
330.2 DIA.
(13.00 DIA.)
Top Cover
Tape Thickness
0.102 MAX.
(0.004 MAX.)
W = 12.00 ± 0.30
(0.472 ± 0.012)
B0 = 5.30 ± 0.10
(0.209 ± 0.004)
Top Cover
Tape
P = 8.00 ± 0.10
(0.315 ± 0.004)
Embossed Carrier
Embossment
K0= 2.10 ± 0.10
(0.083 ± 0.004)
A0 = 6.50 ± 0.10
(0.256 ± 0.004)
User Direction of Feed
Dimensions
mm
(inches)
NOTE: Tape dimensions not shown comply with JEDEC Standard EIA-481-2
3.3 Soldering
3.4 Washing
For proper assembly, this component must be
processed in accordance with the current revision of
IPC/JEDEC standard J-STD-020. Failure to follow the
recommended guidelines may cause permanent
damage to the device resulting in impaired
performance and/or a reduced lifetime expectancy.
Clare does not recommend ultrasonic cleaning of this
part.
Pb
RoHS
2002/95/EC
e3
For additional information please visit www.clare.com
Clare, Inc. makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make
changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses or indemnity are expressed or implied. Except as set
forth in Clare’s Standard Terms and Conditions of Sale, Clare, Inc. assumes no liability whatsoever, and disclaims any express or implied warranty relating to its
products, including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right.
The products described in this document are not designed, intended, authorized, or warranted for use as components in systems intended for surgical implant into
the body, or in other applications intended to support or sustain life, or where malfunction of Clare’s product may result in direct physical harm, injury, or death to a
person or severe property or environmental damage. Clare, Inc. reserves the right to discontinue or make changes to its products at any time without notice.
Specifications: DS-MXHV9910-R01
© Copyright 2009, Clare, Inc.
All rights reserved. Printed in USA.
7/22/09
R01
www.clare.com
11
Similar pages