TI1 LP5907MFX-4.5/NOPB 250-ma ultra-low-noise, low-iq ldo Datasheet

Product
Folder
Sample &
Buy
Technical
Documents
Support &
Community
Tools &
Software
Reference
Design
LP5907
SNVS798L – APRIL 2012 – REVISED SEPTEMBER 2016
LP5907 250-mA Ultra-Low-Noise, Low-IQ LDO
1 Features
3 Description
•
•
•
•
The LP5907 is a low-noise LDO that can supply up to
250 mA output current. Designed to meet the
requirements of RF and analog circuits, the LP5907
device provides low noise, high PSRR, low quiescent
current, and low line or load transient response
figures. Using new innovative design techniques, the
LP5907 offers class-leading noise performance
without a noise bypass capacitor and the ability for
remote output capacitor placement.
1
•
•
•
•
•
•
•
•
•
•
•
Input Voltage Range: 2.2 V to 5.5 V
Output Voltage Range: 1.2 V to 4.5 V
Output Current: 250 mA
Stable with 1-µF Ceramic Input and Output
Capacitors
No Noise Bypass Capacitor Required
Remote Output Capacitor Placement
Thermal-Overload and Short-Circuit Protection
–40°C to 125°C Junction Temperature Range for
Operation
Low Output Voltage Noise: < 6.5 µVRMS
PSRR: 82 dB at 1 kHz
Output Voltage Tolerance: ±2%
Virtually Zero IQ (Disabled): < 1 µA
Very Low IQ (Enabled): 12 µA
Start-up Time: 80 µs
Low Dropout: 120 mV (typical)
The device is designed to work with a 1-µF input and
a 1-µF output ceramic capacitor (no separate noise
bypass capacitor is required).
This device is available with fixed output voltages
from 1.2 V to 4.5 V in 25-mV steps. Contact Texas
Instruments Sales for specific voltage option needs.
Device Information(1)
PART NUMBER
LP5907
2 Applications
•
•
•
•
•
•
•
•
•
PACKAGE
BODY SIZE
DSBGA (4)
0.675 mm × 0.675 mm (MAX)
SOT-23 (5)
2.90 mm × 1.60 mm (NOM)
X2SON (4)
1.00 mm × 1.00 mm (NOM)
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Mobile Phones, Tablets
Digital Cameras and Audio Devices
Portable and Battery-Powered Equipment
Portable Medical Equipment
Smart Meters
RF, PLL, VCO, and Clock Power Supplies
IP Cameras
Drones
Field Transmitters
space
space
space
Simplified Schematic
INPUT
IN
1 PF
ENABLE
OUT
LP5907
OUTPUT
1 PF
EN
GND
GND
Copyright © 2016, Texas Instruments Incorporated
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LP5907
SNVS798L – APRIL 2012 – REVISED SEPTEMBER 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
6.7
4
4
4
5
5
6
7
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Output and Input Capacitors .....................................
Typical Characteristics ..............................................
Detailed Description ............................................ 11
7.1
7.2
7.3
7.4
Overview .................................................................
Functional Block Diagram .......................................
Feature Description.................................................
Device Functional Modes........................................
11
11
11
12
8
Applications and Implementation ...................... 13
8.1 Application Information............................................ 13
8.2 Typical Application .................................................. 13
9 Power Supply Recommendations...................... 16
10 Layout................................................................... 17
10.1
10.2
10.3
10.4
10.5
Layout Guidelines .................................................
Layout Examples...................................................
X2SON Mounting ..................................................
DSBGA Mounting..................................................
DSBGA Light Sensitivity .......................................
17
17
18
18
18
11 Device and Documentation Support ................. 19
11.1
11.2
11.3
11.4
11.5
11.6
Documentation Support ........................................
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
19
19
19
19
19
19
12 Mechanical, Packaging, and Orderable
Information ........................................................... 19
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision K (May 2016) to Revision L
Page
•
Changed title of data sheet and updated list of Applications ................................................................................................ 1
•
Changed "10 µVRMS" to "6.5 µVRMS" ....................................................................................................................................... 1
•
Changed wording of first sentence of Description ................................................................................................................. 1
Changes from Revision J (March 2016) to Revision K
•
Changed "Linear Regulator" to "LDO" in title and first sentence of Description .................................................................... 1
Changes from Revision I (August 2015) to Revision J
•
Page
Page
Changed VOUT min and max values and VEN min value in Abs Max table and VEN row of ROC table to correct format
errors; replace text of footnote 2 of Abs Max table ............................................................................................................... 4
Changes from Revision H (November 2014) to Revision I
Page
•
Added icon for reference design to Top Navs and "ΔVOUT vs Temperature" graph to Typical Characteristics ..................... 1
•
Changed Storage Temperature to Abs Max table; replace Handling Ratings with ESD Ratings ......................................... 4
•
Deleted "VOUT ≥ 1.8 V" from first row of ΔVout spec ............................................................................................................. 5
•
Added "SOT-23, X2SON packages" to second row of ΔVout spec ...................................................................................... 5
Changes from Revision G (October 2013) to Revision H
•
2
Page
Added Device Information and Handling Rating tables, Feature Description, Device Functional Modes, Application
and Implementation, Power Supply Recommendations, Layout, Device and Documentation Support, and
Mechanical, Packaging, and Orderable Information sections; moved some curves to Application Curves section ............. 1
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP5907
LP5907
www.ti.com
SNVS798L – APRIL 2012 – REVISED SEPTEMBER 2016
5 Pin Configuration and Functions
YKE Package
4-Pin DSBGA
IN
A1
OUT
A2
OUT
A2
IN
A1
B1
EN
B2
GND
B2
GND
B1
EN
BOTTOM VIEW
TOP VIEW
DQN Package
4-Pin X2SON
Bottom View
OUT GND
1
2
5
4
3
IN
EN
DBV Package
5-Pin SOT-23
Top View
IN
1
GND
2
EN
3
5 OUT
4 N/C
Pin Functions
PIN
NAME
DSBGA
NUMBER
X2SON
NUMBER
SOT-23
NUMBER
I/O
DESCRIPTION
IN
A1
4
1
I
Input voltage supply. A 1-μF capacitor should be connected at this input.
OUT
A2
1
5
O
Regulated output voltage. A minimum 1-μF low-ESR capacitor should be
connected to this pin. Connect this output to the load circuit. An internal
230-Ω (typical) pulldown resistor prevents a charge remaining on VOUT
when the regulator is in the shutdown mode (VEN low).
Enable input. A low voltage (< VIL) on this pin turns the regulator off and
discharges the output pin to GND through an internal 230-Ω pulldown
resistor. A high voltage (> VIH) on this pin enables the regulator output.
This pin has an internal 1M-Ω pulldown resistor to hold the regulator off
by default.
EN
B1
3
3
I
GND
B2
2
2
—
Common ground
N/C
N/A
N/A
4
—
No internal electrical connection.
Thermal Pad
N/A
5
N/A
—
Thermal pad for X2SON package, connect to GND or leave floating. Do
not connect to any potential other than GND.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP5907
3
LP5907
SNVS798L – APRIL 2012 – REVISED SEPTEMBER 2016
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1) (2)
MIN
MAX
VIN
Input voltage
–0.3
6
VOUT
Output voltage
–0.3
See (3)
VEN
Enable input voltage
–0.3
6
Continuous power dissipation (4)
TJMAX
Junction temperature
Tstg
Storage temperature
(1)
(2)
(3)
(4)
Internally Limited
–65
UNIT
V
W
150
°C
150
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages are with respect to the GND pin.
Abs Max VOUT is the lessor of VIN + 0.3 V, or 6 V.
Internal thermal shutdown circuitry protects the device from permanent damage.
6.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001
Electrostatic discharge
(1)
UNIT
±2000
Charged-device model (CDM), per JEDEC specification JESD22-C101 (2)
V
±1000
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted) (1) (2)
MIN
MAX
VIN
Input supply voltage
2.2
5.5
VEN
Enable input voltage
0
5.5
IOUT
Output current
TJ
Junction temperature
TA
(1)
(2)
(3)
4
Ambient temperature
(3)
UNIT
V
0
250
mA
–40
125
°C
–40
85
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages are with respect to the GND pin.
In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may
have to be derated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJ-MAX-OP =
125°C), the maximum power dissipation of the device in the application (PD-MAX), and the junction-to ambient thermal resistance of the
part/package in the application (RθJA), as given by the following equation: TA-MAX = TJ-MAX-OP – (RθJA × PD-MAX). See Applications and
Implementation.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP5907
LP5907
www.ti.com
SNVS798L – APRIL 2012 – REVISED SEPTEMBER 2016
6.4 Thermal Information
LP5907
THERMAL METRIC (1)
DBV (SOT-23) DQN (X2SON) YKE (DSBGA)
UNIT
5 PINS
4 PINS
4 PINS
206.1
°C/W
RθJA
Junction-to-ambient thermal resistance
193.4
216.1
RθJC(top)
Junction-to-case (top) thermal resistance
102.1
161.7
1.5
°C/W
RθJB
Junction-to-board thermal resistance
45.8
162.1
37.0
°C/W
ψJT
Junction-to-top characterization parameter
8.4
5.1
15.0
°C/W
ψJB
Junction-to-board characterization parameter
45.3
161.7
36.8
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
n/a
123.0
n/a
°C/W
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
6.5 Electrical Characteristics
VIN = VOUT(NOM) + 1 V, VEN = 1.2 V, IOUT = 1 mA, CIN = 1 µF, COUT = 1 µF, unless otherwise stated. (1) (2) (3)
PARAMETER
VIN
TEST CONDITIONS
Input voltage
Output voltage tolerance
ΔVOUT
ILOAD
MIN
5.5
VIN = (VOUT(NOM) + 1 V) to 5.5 V,
IOUT = 1 mA to 250 mA
–2
2
VIN = (VOUT(NOM) + 1 V) to 5.5 V,
IOUT = 1 mA to 250 mA
(VOUT < 1.8 V, SOT-23, X2SON packages)
–3
3
VIN = (VOUT(NOM) + 1 V) to 5.5 V,
IOUT = 1 mA
Load regulation
IOUT = 1 mA to 250 mA
Load current
See (4)
Quiescent current
IG
Ground current (6)
VDO
Dropout voltage (7)
PSRR
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
Power supply rejection ratio (9)
%/mA
250
mA
250
12
25
VEN = 1.2 V, IOUT = 250 mA
250
425
VEN = 0.3 V (Disabled)
0.2
1
VEN = 1.2 V, IOUT = 0 mA
14
TA = 25°C (8)
µA
µA
50
IOUT = 250 mA (DSBGA package)
120
IOUT = 250 mA (SOT-23, X2SON packages)
Short circuit current limit
%/V
0.001
IOUT = 100 mA
ISC
V
0.02
0
Maximum output current
UNIT
%VOUT
VEN = 1.2 V, IOUT = 0 mA
IQ
MAX
2.2
Line regulation
(5)
TYP
TA = 25°C
200
mV
250
250
500
f = 100 Hz, IOUT = 20 mA
90
f = 1 kHz, IOUT = 20 mA
82
f = 10 kHz, IOUT = 20 mA
65
f = 100 kHz, IOUT = 20 mA
60
mA
dB
All voltages are with respect to the device GND terminal, unless otherwise stated.
Minimum and maximum limits are ensured through test, design, or statistical correlation over the junction temperature (TJ) range of
–40°C to 125°C, unless otherwise stated. Typical values represent the most likely parametric norm at TA = 25°C, and are provided for
reference purposes only.
In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may
have to be derated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJ-MAX-OP =
125°C), the maximum power dissipation of the device in the application (PD-MAX), and the junction-to ambient thermal resistance of the
part/package in the application RθJA), as given by the following equation: TA-MAX = TJ-MAX-OP – (RθJA × PD-MAX). See Applications and
Implementation.
The device maintains a stable, regulated output voltage without a load current.
Quiescent current is defined here as the difference in current between the input voltage source and the load at VOUT.
Ground current is defined here as the total current flowing to ground as a result of all input voltages applied to the device.
Dropout voltage is the voltage difference between the input and the output at which the output voltage drops to 100 mV below its
nominal value.
Short-circuit current (ISC) for the LP5907 is equivalent to current limit. To minimize thermal effects during testing, ISC is measured with
VOUT pulled to 100 mV below its nominal voltage.
This specification is verified by design.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP5907
5
LP5907
SNVS798L – APRIL 2012 – REVISED SEPTEMBER 2016
www.ti.com
Electrical Characteristics (continued)
VIN = VOUT(NOM) + 1 V, VEN = 1.2 V, IOUT = 1 mA, CIN = 1 µF, COUT = 1 µF, unless otherwise stated.(1)(2)(3)
PARAMETER
TEST CONDITIONS
MIN
TYP
IOUT = 1 mA
10
IOUT = 250 mA
6.5
eN
Output noise voltage (9)
BW = 10 Hz to 100 kHz
RAD
Output Automatic Discharge
pulldown resistance
VEN < VIL (output disabled)
230
Thermal shutdown
TJ rising
160
Thermal hysteresis
TJ falling from shutdown
TSD
MAX
UNIT
µVRMS
Ω
°C
15
LOGIC INPUT THRESHOLDS
VIL
Low input threshold
VIN = 2.2 V to 5.5 V
VEN falling until the output is disabled
VIH
High input threshold
VIN = 2.2 V to 5.5 V
VEN rising until the output is enabled
IEN
Input current at EN pin (10)
0.4
1.2
VEN = 5.5 V and VIN = 5.5 V
V
5.5
VEN = 0 V and VIN = 5.5 V
V
µA
0.001
TRANSIENT CHARACTERISTICS
Line transient
VIN = (VOUT(NOM) + 1 V) to
(VOUT(NOM) + 1.6 V) in 30 µs
(9)
mV
VIN = (VOUT(NOM) + 1.6 V) to
(VOUT(NOM) + 1.6 V) in 30 µs
ΔVOUT
1
IOUT = 1 mA to 250 mA in 10 µs
Load transient (9)
tON
–1
–40
IOUT = 250 mA to 1mA in 10 µs
40
Overshoot on start-up (9)
Stated as a percentage of VOUT(NOM)
Turnon time
From VEN > VIH to VOUT = 95% of VOUT(NOM)
TA = 25°C
mV
5%
80
150
µs
(10) There is a 1-MΩ resistor between EN and ground on the device.
6.6 Output and Input Capacitors
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
(2)
CIN
Input capacitance
COUT
Output capacitance (2)
ESR
(1)
(2)
6
Output/Input capacitance
Capacitance for stability
(2)
MIN (1)
TYP
0.7
1
0.7
1
5
MAX
UNIT
µF
10
µF
500
mΩ
The minimum capacitance should be greater than 0.5 μF over the full range of operating conditions. The capacitor tolerance should be
30% or better over the full temperature range. The full range of operating conditions for the capacitor in the application must be
considered during device selection to ensure this minimum capacitance specification is met. X7R capacitors are recommended however
capacitor types X5R, Y5V and Z5U may be used with consideration of the application and conditions.
This specification is verified by design.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP5907
LP5907
www.ti.com
SNVS798L – APRIL 2012 – REVISED SEPTEMBER 2016
6.7 Typical Characteristics
Unless otherwise stated: VIN = 3.7 V, VOUT = 2.8 V, IOUT = 1 mA, CIN = 1 µF, COUT = 1 µF, TA = 25°C
1
16
14
0.9
10
VEN (V)
IQ( A)
12
8
6
0.8
0.7
4
0.6
2
VIH Rising
VIL Falling
0
2.3
2.8
3.3
3.8 4.3
VIN(V)
4.8
5.3
0.5
5.8
2
2.5
3
3.5
SVA-30180569
4
VIN (V)
4.5
5
5.5
6
D001
Figure 2. VEN Thresholds vs VIN
Figure 1. Quiescent Current vs Input Voltage
5
1.4
4.5
1.2
4
3.5
VOUT (V)
VOUT (V)
1
0.8
0.6
3
2.5
2
1.5
0.4
1
0.2
RLOAD = 1.2 k:
RLOAD = 4.8 :
RLOAD = 4.5 k:
RLOAD = 18 :
0.5
0
0
0
0.5
1
1.5
2
2.5
VIN (V)
VOUT = 1.2V
0
1
2
D002
VEN = VIN
VOUT = 4.5V
4
5
6
D003
VEN = VIN
Figure 3. VOUT vs VIN
Figure 4. VOUT vs VIN
350
2.900
300
2.875
250
2.850
VIN= 3.6V
2.825
VOUT(V)
GROUND CURRENT ( A)
3
VIN (V)
200
2.800
150
2.775
100
2.750
VIN = 3.0V
VIN = 3.8V
VIN = 4.2V
VIN = 5.5V
50
0
0
50
100 150 200
IOUT(mA)
250
-40°C
90°C
25°C
2.725
2.700
300
SVA-30180571
Figure 5. Ground Current vs Output Current
0
50
100
150
LOAD (mA)
200
250
SVA-30180567
Figure 6. Load Regulation
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP5907
7
LP5907
SNVS798L – APRIL 2012 – REVISED SEPTEMBER 2016
www.ti.com
Typical Characteristics (continued)
Unless otherwise stated: VIN = 3.7 V, VOUT = 2.8 V, IOUT = 1 mA, CIN = 1 µF, COUT = 1 µF, TA = 25°C
2.900
0.2
Load = 10 mA
2.875
0.1
2.850
2.825
VOUT(V)
'VOUT (%)
0
2.800
-0.1
2.775
-0.2
2.750
-40°C
90°C
25°C
2.725
-0.3
2.700
-0.4
-50
-25
0
25
50
75
Junction Temperature (qC)
100
3.0
125
3.5
D010
4.0
4.5
VIN(V)
5.0
5.5
SVA-30180568
Figure 8. Line Regulation
Figure 7. ΔVOUT vs Temperature
2V/DIV
VOUT
VOUT
(AC Coupled)
10 mV/
DIV
VIN
1V/DIV
2V/DIV
VIN = VEN
1A/DIV
IIN
2 ms/DIV
10 s/DIV
SVA-30180509
SVA-30180510
VIN = 3.2 V ↔ 4.2 V
Figure 9. Inrush Current
Load = 1 mA
Figure 10. Line Transient
VOUT
(AC Coupled)
10 mV/
DIV
VIN
1V/DIV
VOUT
100 mV/DIV
LOAD
200 mA/DIV
10 s/DIV
100 s/DIV
SVA-30180511
VIN = 3.2 V ↔ 4.2 V
Load = 250 mA
SVA-30180512
Load = 0 mA ↔ 250 mA
Figure 11. Line Transient
8
–40°C
Figure 12. Load Transient
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP5907
LP5907
www.ti.com
SNVS798L – APRIL 2012 – REVISED SEPTEMBER 2016
Typical Characteristics (continued)
Unless otherwise stated: VIN = 3.7 V, VOUT = 2.8 V, IOUT = 1 mA, CIN = 1 µF, COUT = 1 µF, TA = 25°C
VOUT
100 mV/DIV
LOAD
200 mA/DIV
VOUT
100 mV/DIV
LOAD
200 mA/DIV
100 s/DIV
100 s/DIV
SVA-30180513
Load = 0 mA ↔ 250 mA
90°C
SVA-30180514
Load = 0 mA ↔ 250 mA
Figure 13. Load Transient
25°C
Figure 14. Load Transient
1V/DIV
1V/DIV
VOUT
VOUT
1V/DIV
1V/DIV
EN
EN
20 s/DIV
20 s/DIV
SVA-30180516
SVA-30180515
Load = 250 mA
Load = 0 mA
Figure 15. Start-Up
Figure 16. Start-Up
DROPOUT VOLTAGE (mV)
140
120
100
80
60
40
Dropout Voltage
20
0
0
50
100
150
200
LOAD CURRENT (mA)
250
SVA-30180573
Figure 18. Dropout Voltage vs Load Current
Figure 17. Noise Density Test
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP5907
9
LP5907
SNVS798L – APRIL 2012 – REVISED SEPTEMBER 2016
www.ti.com
Typical Characteristics (continued)
Unless otherwise stated: VIN = 3.7 V, VOUT = 2.8 V, IOUT = 1 mA, CIN = 1 µF, COUT = 1 µF, TA = 25°C
0
0
250 mA
200 mA
150 mA
100 mA
50 mA
20 mA
PSRR (dB)
-40
-20
-40
PSRR (dB)
-20
-60
-80
-80
-100
-100
-120
0.1
1
10
FREQUENCY (kHz)
100
250 mA
200 mA
150 mA
100 mA
50 mA
20 mA
-120
0.01
D004
Figure 19. PSRR Loads Averaged 100 Hz To 100 KHz
10
-60
0.1
1
10
100
FREQUENCY (kHz)
1000
10000
D005
Figure 20. PSRR Loads Averaged 10 Hz To 10 MHz
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP5907
LP5907
www.ti.com
SNVS798L – APRIL 2012 – REVISED SEPTEMBER 2016
7 Detailed Description
7.1 Overview
Designed to meet the needs of sensitive RF and analog circuits, the LP5907 provides low noise, high PSRR, low
quiescent current, as well as low line and load transient response figures. Using new innovative design
techniques, the LP5907 offers class leading noise performance without the need for a separate noise filter
capacitor.
The LP5907 is designed to perform with a single 1-µF input capacitor and a single 1-µF ceramic output
capacitor. With a reasonable PCB layout, the single 1-µF ceramic output capacitor can be placed up to 10 cm
away from the LP5907 device.
7.2 Functional Block Diagram
OUT
IN
POR
EN
EN
+
RF
CF
+
VBG
1.20V
RAD
EN
+
EN
EN
1M
VIH
GND
Copyright © 2016, Texas Instruments Incorporated
7.3 Feature Description
7.3.1 Enable (EN)
The LP5907 EN pin is internally held low by a 1-MΩ resistor to GND. The EN pin voltage must be higher than the
VIH threshold to ensure that the device is fully enabled under all operating conditions. The EN pin voltage must
be lower than the VIL threshold to ensure that the device is fully disabled and the automatic output discharge is
activated.
7.3.2 Low Output Noise
Any internal noise at the LP5907 reference voltage is reduced by a first order low-pass RC filter before it is
passed to the output buffer stage. The low-pass RC filter has a –3 dB cut-off frequency of approximately 0.1 Hz.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP5907
11
LP5907
SNVS798L – APRIL 2012 – REVISED SEPTEMBER 2016
www.ti.com
Feature Description (continued)
7.3.3 Output Automatic Discharge
The LP5907 output employs an internal 230-Ω (typical) pulldown resistance to discharge the output when the EN
pin is low, and the device is disabled.
7.3.4 Remote Output Capacitor Placement
The LP5907 requires at least a 1-µF capacitor at the OUT pin, but there are no strict requirements about the
location of the capacitor in regards the OUT pin. In practical designs, the output capacitor may be located up to
10 cm away from the LDO.
7.3.5 Thermal Overload Protection (TSD)
Thermal shutdown disables the output when the junction temperature rises to approximately 160°C which allows
the device to cool. When the junction temperature cools to approximately 145°C, the output circuitry enables.
Based on power dissipation, thermal resistance, and ambient temperature, the thermal protection circuit may
cycle on and off. This thermal cycling limits the dissipation of the regulator and protects it from damage as a
result of overheating.
The thermal shutdown circuitry of the LP5907 has been designed to protect against temporary thermal overload
conditions. The TSD circuitry was not intended to replace proper heat-sinking. Continuously running the LP5907
device into thermal shutdown may degrade device reliability.
7.4 Device Functional Modes
7.4.1 Enable (EN)
The LP5907 Enable (EN) pin is internally held low by a 1-MΩ resistor to GND. The EN pin voltage must be
higher than the VIH threshold to ensure that the device is fully enabled under all operating conditions.
When the EN pin is pulled low, and the output is disabled, the output automatic discharge circuitry is activated.
Any charge on the OUT pin is discharged to GND through the internal 230-Ω (typical) pulldown resistance.
7.4.2 Minimum Operating Input Voltage (VIN)
The LP5907 does not include any dedicated UVLO circuitry. The LP5907 internal circuitry is not fully functional
until VIN is at least 2.2 V. The output voltage is not regulated until VIN has reached at least the greater of 2.2 V or
(VOUT + VDO).
12
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP5907
LP5907
www.ti.com
SNVS798L – APRIL 2012 – REVISED SEPTEMBER 2016
8 Applications and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LP5907 is designed to meet the requirements of RF and analog circuits, by providing low noise, high PSRR,
low quiescent current, and low line or load transient response figures. The device offers excellent noise
performance without the need for a noise bypass capacitor and is stable with input and output capacitors with a
value of 1 µF. The LP5907 delivers this performance in industry standard packages such as DSBGA, X2SON,
and SOT-23 which, for this device, are specified with an operating junction temperature (TJ) of –40°C to 125°C.
8.2 Typical Application
Figure 21 shows the typical application circuit for the LP5907. Input and output capacitances may need to be
increased above the 1 µF minimum for some applications.
INPUT
IN
1 PF
ENABLE
OUT
LP5907
OUTPUT
1 PF
EN
GND
GND
Copyright © 2016, Texas Instruments Incorporated
Figure 21. LP5907 Typical Application
8.2.1 Design Requirements
DESIGN PARAMETER
EXAMPLE VALUE
Input voltage range
2.2 V to 5.5 V
Output voltage
1.8 V
Output current
200 mA
Output capacitor range
0.7 µF to 10 µF
Input/Output capacitor ESR range
5 to 500 mΩ
8.2.2 Detailed Design Procedure
8.2.2.1 Power Dissipation and Device Operation
The permissible power dissipation for any package is a measure of the capability of the device to pass heat from
the power source, the junctions of the IC, to the ultimate heat sink, the ambient environment. Thus, the power
dissipation is dependent on the ambient temperature and the thermal resistance across the various interfaces
between the die junction and ambient air.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP5907
13
LP5907
SNVS798L – APRIL 2012 – REVISED SEPTEMBER 2016
www.ti.com
The maximum allowable power dissipation for the device in a given package can be calculated using Equation 1:
PD-MAX = ((TJ-MAX – TA) / RθJA)
(1)
The actual power being dissipated in the device can be represented by Equation 2:
PD = (VIN – VOUT) × IOUT
(2)
These two equations establish the relationship between the maximum power dissipation allowed due to thermal
consideration, the voltage drop across the device, and the continuous current capability of the device. These two
equations should be used to determine the optimum operating conditions for the device in the application.
In applications where lower power dissipation (PD) and/or excellent package thermal resistance (RθJA) is present,
the maximum ambient temperature (TA-MAX) may be increased.
In applications where high power dissipation and/or poor package thermal resistance is present, the maximum
ambient temperature (TA-MAX) may have to be derated. TA-MAX is dependent on the maximum operating junction
temperature (TJ-MAX-OP = 125°C), the maximum allowable power dissipation in the device package in the
application (PD-MAX), and the junction-to ambient thermal resistance of the part/package in the application (RθJA),
as given by Equation 3:
TA-MAX = (TJ-MAX-OP – (RθJA × PD-MAX))
(3)
Alternately, if TA-MAX can not be derated, the PD value must be reduced. This can be accomplished by reducing
VIN in the VIN–VOUT term as long as the minimum VIN is met, or by reducing the IOUT term, or by some
combination of the two.
8.2.2.2 External Capacitors
Like most low-dropout regulators, the LP5907 requires external capacitors for regulator stability. The device is
specifically designed for portable applications requiring minimum board space and smallest components. These
capacitors must be correctly selected for good performance.
8.2.2.3 Input Capacitor
An input capacitor is required for stability. The input capacitor should be at least equal to, or greater than, the
output capacitor for good load transient performance. At least a 1 µF capacitor has to be connected between the
LP5907 input pin and ground for stable operation over full load current range. Basically, it is ok to have more
output capacitance than input, as long as the input is at least 1 µF.
The input capacitor must be located a distance of not more than 1 cm from the input pin and returned to a clean
analog ground. Any good quality ceramic, tantalum, or film capacitor may be used at the input.
NOTE
To ensure stable operation it is essential that good PCB practices are employed to
minimize ground impedance and keep input inductance low. If these conditions cannot be
met, or if long leads are to be used to connect the battery or other power source to the
LP5907, TI recommends increasing the input capacitor to at least 10 µF. Also, tantalum
capacitors can suffer catastrophic failures due to surge current when connected to a lowimpedance source of power (like a battery or a very large capacitor). If a tantalum
capacitor is used at the input, it should be verified by the manufacturer to have a surge
current rating sufficient for the application. The initial tolerance, applied voltage de-rating,
and temperature coefficient must all be considered when selecting the input capacitor to
ensure the actual capacitance is never less than 0.7 µF over the entire operating range.
8.2.2.4 Output Capacitor
The LP5907 is designed specifically to work with a very small ceramic output capacitor, typically 1 µF. A ceramic
capacitor (dielectric types X5R or X7R) in the 1 µF to 10 µF range, and with ESR between 5 mΩ to 500 mΩ, is
suitable in the LP5907 application circuit. For this device the output capacitor should be connected between the
OUT pin and a good connection back to the GND pin.
It may also be possible to use tantalum or film capacitors at the device output, VOUT, but these are not as
attractive for reasons of size and cost (see Capacitor Characteristics).
14
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP5907
LP5907
www.ti.com
SNVS798L – APRIL 2012 – REVISED SEPTEMBER 2016
The output capacitor must meet the requirement for the minimum value of capacitance and have an ESR value
that is within the range 5 mΩ to 500 mΩ for stability. Like the input capacitor, the initial tolerance, applied voltage
de-rating, and temperature coefficient must all be considered when selecting the input capacitor to ensure the
actual capacitance is never less than 0.7 µF over the entire operating range.
8.2.2.5 Capacitor Characteristics
The LP5907 is designed to work with ceramic capacitors on the input and output to take advantage of the
benefits they offer. For capacitance values in the range of 1 µF to 10 µF, ceramic capacitors are the smallest,
least expensive and have the lowest ESR values, thus making them best for eliminating high frequency noise.
The ESR of a typical 1 µF ceramic capacitor is in the range of 20 mΩ to 40 mΩ, which easily meets the ESR
requirement for stability for the LP5907.
A better choice for temperature coefficient in a ceramic capacitor is X7R. This type of capacitor is the most stable
and holds the capacitance within ±15% over the temperature range. Tantalum capacitors are less desirable than
ceramic for use as output capacitors because they are more expensive when comparing equivalent capacitance
and voltage ratings in the 1 µF to 10 µF range.
Another important consideration is that tantalum capacitors have higher ESR values than equivalent size
ceramics. This means that while it may be possible to find a tantalum capacitor with an ESR value within the
stable range, it would have to be larger in capacitance (which means bigger and more costly) than a ceramic
capacitor with the same ESR value. It should also be noted that the ESR of a typical tantalum increases about
2:1 as the temperature goes from 25°C down to –40°C, so some guard band must be allowed.
8.2.2.6 Remote Capacitor Operation
The LP5907 requires at least a 1-µF capacitor at the OUT pin, but there is no strict requirements about the
location of the capacitor in regards to the pin. In practical designs the output capacitor may be located up to 10
cm away from the LDO. This means that there is no need to have a special capacitor close to the output pin if
there is already respective capacitors in the system (like a capacitor at the input of supplied part). The remote
capacitor feature helps user to minimize the number of capacitors in the system.
As a good design practice, keep the wiring parasitic inductance at a minimum, which means to use as wide as
possible traces from the LDO output to the capacitors, keeping the LDO output trace layer as close to ground
layer as possible and avoiding vias on the path. If there is a need to use vias, implement as many as possible
vias between the connection layers. The recommendation is to keep parasitic wiring inductance less than 35 nH.
For the applications with fast load transients, it is recommended to use an input capacitor equal to or larger to
the sum of the capacitance at the output node for the best load transient performance.
8.2.2.7 No-Load Stability
The LP5907 remains stable, and in regulation, with no external load.
8.2.2.8 Enable Control
The LP5907 may be switched ON or OFF by a logic input at the EN pin. A voltage on this pin greater than VIH
turns the device on, while a voltage less than VIL turns the device off.
When the EN pin is low, the regulator output is off and the device typically consumes less than 1 µA.
Additionally, an output pulldown circuit is activated which ensures that any charge stored on COUT is discharged
to ground.
If the application does not require the use of the shutdown feature, the EN pin can be tied directly to the IN pin to
keep the regulator output permanently on.
An internal 1-MΩ pulldown resistor ties the EN input to ground, ensuring that the device remains off if the EN pin
is left open circuit. To ensure proper operation, the signal source used to drive the EN pin must be able to swing
above and below the specified turnon or turnoff voltage thresholds listed in the Electrical Characteristics under
VIL and VIH.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP5907
15
LP5907
SNVS798L – APRIL 2012 – REVISED SEPTEMBER 2016
www.ti.com
8.2.3 Application Curves
1V/DIV
VOUT
100 mV/DIV
LOAD
200 mA/DIV
VOUT
1V/DIV
EN
100 s/DIV
20 s/DIV
SVA-30180515
SVA-30180514
Figure 23. Load Transient Response
Figure 22. Start-Up
9 Power Supply Recommendations
This device is designed to operate from an input supply voltage range of 2.2 V to 5.5 V. The input supply must
be well regulated and free of spurious noise. To ensure that the LP5907 output voltage is well regulated and
dynamic performance is optimum, the input supply must be at least VOUT + 1 V. A minimum capacitor value of 1
µF is required to be within 1 cm of the IN pin.
16
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP5907
LP5907
www.ti.com
SNVS798L – APRIL 2012 – REVISED SEPTEMBER 2016
10 Layout
10.1 Layout Guidelines
The dynamic performance of the LP5907 is dependant on the layout of the PCB. PCB layout practices that are
adequate for typical LDOs may degrade the PSRR, noise, or transient performance of the LP5907.
Best performance is achieved by placing CIN and COUT on the same side of the PCB as the LP5907, and as
close to the package as is practical. The ground connections for CIN and COUT must be back to the LP5907
ground pin using as wide and short a copper trace as is practical.
Connections using long trace lengths, narrow trace widths, and/or connections through vias must be avoided.
These add parasitic inductances and resistance that results in inferior performance especially during transient
conditions
10.2 Layout Examples
VIN
VOUT
CIN
1
IN
2
GND
3
EN
5
OUT
COUT
GND
Enable
GND
4
N/C
Figure 24. LP5907MF-x.x (SOT-23) Typical Layout
LP5907SN
VOUT
1
VIN
4
COUT
CIN
2
3
Power Ground
VEN
Figure 25. LP5907SN-xx (X2SON) Typical Layout
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP5907
17
LP5907
SNVS798L – APRIL 2012 – REVISED SEPTEMBER 2016
www.ti.com
Layout Examples (continued)
VIN
LP5907UV
A1
VOUT
A2
COUT
CIN
B1
B2
Power Ground
VEN
Figure 26. LP5907UV-x.x (DSBGA) Typical Layout
10.3 X2SON Mounting
The X2SON package thermal pad must be soldered to the printed circuit board for proper thermal and
mechanical performance. For more information, see the Application Report QFN/SON PCB Attachment
(SLUA271).
10.4 DSBGA Mounting
The DSBGA package requires specific mounting techniques, which are detailed in AN-1112 DSBGA Wafer Level
Chip Scale Package (SNVA009). For best results during assembly, alignment ordinals on the PC board may be
used to facilitate placement of the DSBGA device.
10.5 DSBGA Light Sensitivity
Exposing the DSBGA device to direct light may cause incorrect operation of the device. Light sources such as
halogen lamps can affect electrical performance if they are situated in proximity to the device. Light with
wavelengths in the red and infrared part of the spectrum have the most detrimental effect; thus, the fluorescent
lighting used inside most buildings has very little effect on performance.
18
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP5907
LP5907
www.ti.com
SNVS798L – APRIL 2012 – REVISED SEPTEMBER 2016
11 Device and Documentation Support
11.1 Documentation Support
11.1.1 Related Documentation
For related documentation, see the following:
• AN-1112 DSBGA Wafer Level Chip Scale Package (SNVA009)
• Texas Instruments Application Report QFN/SON PCB Attachment (SLUA271)
11.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
11.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP5907
19
LP5907
SNVS798L – APRIL 2012 – REVISED SEPTEMBER 2016
www.ti.com
PACKAGE OUTLINE
DQN0004A
X2SON - 0.4 mm max height
PLASTIC SMALL OUTLINE - NO LEAD
4215302/D 06/2016
NOTES:
1.
2.
3.
4.
20
All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
This drawing is subject to change without notice.
The package thermal pad must be soldered to the printed circuit board for thermal and mechanical performance.
Features may not exist. Recommend use of pin 1 marking on top of package for orientation purposes.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP5907
LP5907
www.ti.com
SNVS798L – APRIL 2012 – REVISED SEPTEMBER 2016
EXAMPLE BOARD LAYOUT
DQN0004A
X2SON - 0.4 mm max height
PLASTIC SMALL OUTLINE - NO LEAD
4215302/D 06/2016
NOTES: (continued)
5.
This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature
number SLUA271 (www.ti.com/lit/slua271) .
6.
If any vias are implemented, it is recommended that vias under paste be filled, plugged or tented.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP5907
21
LP5907
SNVS798L – APRIL 2012 – REVISED SEPTEMBER 2016
www.ti.com
EXAMPLE STENCIL DESIGN
DQN0004A
X2SON - 0.4 mm max height
PLASTIC SMALL OUTLINE - NO LEAD
4215302/D 06/2016
NOTES: (continued)
7.
22
Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
Submit Documentation Feedback
Copyright © 2012–2016, Texas Instruments Incorporated
Product Folder Links: LP5907
PACKAGE OPTION ADDENDUM
www.ti.com
10-Aug-2017
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LP5907A28YKMR
ACTIVE
DSBGA
YKM
4
3000
Green (RoHS
& no Sb/Br)
Call TI
Level-1-260C-UNLIM
-40 to 125
Q
LP5907A33YKMR
ACTIVE
DSBGA
YKM
4
3000
Green (RoHS
& no Sb/Br)
Call TI
Level-1-260C-UNLIM
-40 to 125
N
LP5907MFX-1.2/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LLTB
LP5907MFX-1.5/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LN8B
LP5907MFX-1.8/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LLUB
LP5907MFX-2.5/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LN7B
LP5907MFX-2.8/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LLYB
LP5907MFX-2.85/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LN4B
LP5907MFX-2.9/NOPB
PREVIEW
SOT-23
DBV
5
3000
TBD
Call TI
Call TI
-40 to 125
1E5X
LP5907MFX-3.0/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LLZB
LP5907MFX-3.1/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LN5B
LP5907MFX-3.2/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LN6B
LP5907MFX-3.3/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LLVB
LP5907MFX-4.5/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LLXB
LP5907SNX-1.2/NOPB
ACTIVE
X2SON
DQN
4
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
CF
LP5907SNX-1.8/NOPB
ACTIVE
X2SON
DQN
4
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
CG
LP5907SNX-1.9
ACTIVE
X2SON
DQN
4
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
3Z
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
10-Aug-2017
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LP5907SNX-2.2/NOPB
ACTIVE
X2SON
DQN
4
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
EP
LP5907SNX-2.5/NOPB
ACTIVE
X2SON
DQN
4
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
F9
LP5907SNX-2.7/NOPB
ACTIVE
X2SON
DQN
4
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
CH
LP5907SNX-2.75
ACTIVE
X2SON
DQN
4
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
HI
LP5907SNX-2.8/NOPB
ACTIVE
X2SON
DQN
4
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
CI
LP5907SNX-2.85/NOPB
ACTIVE
X2SON
DQN
4
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
CJ
LP5907SNX-2.9/NOPB
ACTIVE
X2SON
DQN
4
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
GV
LP5907SNX-3.0/NOPB
ACTIVE
X2SON
DQN
4
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
CK
LP5907SNX-3.1/NOPB
ACTIVE
X2SON
DQN
4
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
CL
LP5907SNX-3.2/NOPB
ACTIVE
X2SON
DQN
4
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
CM
LP5907SNX-3.3/NOPB
ACTIVE
X2SON
DQN
4
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
CN
LP5907SNX-4.0/NOPB
ACTIVE
X2SON
DQN
4
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
GU
LP5907SNX-4.5/NOPB
ACTIVE
X2SON
DQN
4
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 125
CO
LP5907UVE-1.2/NOPB
ACTIVE
DSBGA
YKE
4
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
R
LP5907UVE-1.8/NOPB
ACTIVE
DSBGA
YKE
4
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
S
LP5907UVE-2.8/NOPB
ACTIVE
DSBGA
YKE
4
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
U
LP5907UVE-2.85/NOPB
ACTIVE
DSBGA
YKE
4
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
V
LP5907UVE-3.0/NOPB
ACTIVE
DSBGA
YKE
4
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
B
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
10-Aug-2017
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LP5907UVE-3.1/NOPB
ACTIVE
DSBGA
YKE
4
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
X
LP5907UVE-3.2/NOPB
ACTIVE
DSBGA
YKE
4
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
C
LP5907UVE-3.3/NOPB
ACTIVE
DSBGA
YKE
4
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
D
LP5907UVE-4.5/NOPB
ACTIVE
DSBGA
YKE
4
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
Z
LP5907UVX-1.2/NOPB
ACTIVE
DSBGA
YKE
4
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
R
LP5907UVX-1.8/NOPB
ACTIVE
DSBGA
YKE
4
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
S
LP5907UVX-2.5/NOPB
ACTIVE
DSBGA
YKE
4
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
E
LP5907UVX-2.8/NOPB
ACTIVE
DSBGA
YKE
4
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
U
LP5907UVX-2.85/NOPB
ACTIVE
DSBGA
YKE
4
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
V
LP5907UVX-3.0/NOPB
ACTIVE
DSBGA
YKE
4
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
B
LP5907UVX-3.1/NOPB
ACTIVE
DSBGA
YKE
4
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
X
LP5907UVX-3.2/NOPB
ACTIVE
DSBGA
YKE
4
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
C
LP5907UVX-3.3/NOPB
ACTIVE
DSBGA
YKE
4
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
D
LP5907UVX-4.5/NOPB
ACTIVE
DSBGA
YKE
4
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
Z
LP5907UVX19/NOPB
ACTIVE
DSBGA
YKE
4
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
8
LP5907UVX37/NOPB
ACTIVE
DSBGA
YKE
4
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
9
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
Addendum-Page 3
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
10-Aug-2017
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LP5907 :
• Automotive: LP5907-Q1
NOTE: Qualified Version Definitions:
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 4
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Aug-2017
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
LP5907A28YKMR
DSBGA
YKM
4
3000
178.0
8.4
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
0.74
0.74
0.54
4.0
8.0
Q1
LP5907A33YKMR
DSBGA
YKM
4
3000
178.0
8.4
0.74
0.74
0.54
4.0
8.0
Q1
LP5907MFX-1.2/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP5907MFX-1.5/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP5907MFX-1.8/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP5907MFX-2.5/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP5907MFX-2.8/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP5907MFX-2.85/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP5907MFX-3.0/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP5907MFX-3.1/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP5907MFX-3.2/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP5907MFX-3.3/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP5907MFX-4.5/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LP5907SNX-1.2/NOPB
X2SON
DQN
4
3000
180.0
9.5
1.16
1.16
0.63
4.0
8.0
Q2
LP5907SNX-1.8/NOPB
X2SON
DQN
4
3000
180.0
9.5
1.16
1.16
0.63
4.0
8.0
Q2
LP5907SNX-1.9
X2SON
DQN
4
3000
180.0
9.5
1.16
1.16
0.63
4.0
8.0
Q2
LP5907SNX-2.2/NOPB
X2SON
DQN
4
3000
180.0
9.5
1.16
1.16
0.63
4.0
8.0
Q2
LP5907SNX-2.5/NOPB
X2SON
DQN
4
3000
180.0
9.5
1.16
1.16
0.63
4.0
8.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Aug-2017
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LP5907SNX-2.7/NOPB
X2SON
DQN
4
3000
180.0
9.5
1.16
1.16
0.63
4.0
8.0
Q2
LP5907SNX-2.75
X2SON
DQN
4
3000
180.0
8.4
1.16
1.16
0.63
4.0
8.0
Q2
LP5907SNX-2.75
X2SON
DQN
4
3000
180.0
9.5
1.16
1.16
0.63
4.0
8.0
Q2
LP5907SNX-2.8/NOPB
X2SON
DQN
4
3000
180.0
9.5
1.16
1.16
0.63
4.0
8.0
Q2
LP5907SNX-2.85/NOPB
X2SON
DQN
4
3000
180.0
8.4
1.16
1.16
0.63
4.0
8.0
Q2
LP5907SNX-2.85/NOPB
X2SON
DQN
4
3000
180.0
9.5
1.16
1.16
0.63
4.0
8.0
Q2
LP5907SNX-2.9/NOPB
X2SON
DQN
4
3000
180.0
9.5
1.16
1.16
0.63
4.0
8.0
Q2
LP5907SNX-3.0/NOPB
X2SON
DQN
4
3000
180.0
9.5
1.16
1.16
0.63
4.0
8.0
Q2
LP5907SNX-3.1/NOPB
X2SON
DQN
4
3000
180.0
9.5
1.16
1.16
0.63
4.0
8.0
Q2
LP5907SNX-3.2/NOPB
X2SON
DQN
4
3000
180.0
9.5
1.16
1.16
0.63
4.0
8.0
Q2
LP5907SNX-3.3/NOPB
X2SON
DQN
4
3000
180.0
9.5
1.16
1.16
0.63
4.0
8.0
Q2
LP5907SNX-4.0/NOPB
X2SON
DQN
4
3000
180.0
9.5
1.16
1.16
0.63
4.0
8.0
Q2
LP5907SNX-4.5/NOPB
X2SON
DQN
4
3000
180.0
9.5
1.16
1.16
0.63
4.0
8.0
Q2
LP5907UVE-1.2/NOPB
DSBGA
YKE
4
250
178.0
8.4
0.71
0.71
0.51
4.0
8.0
Q1
LP5907UVE-1.8/NOPB
DSBGA
YKE
4
250
178.0
8.4
0.71
0.71
0.51
4.0
8.0
Q1
LP5907UVE-2.8/NOPB
DSBGA
YKE
4
250
178.0
8.4
0.71
0.71
0.51
4.0
8.0
Q1
LP5907UVE-2.85/NOPB
DSBGA
YKE
4
250
178.0
8.4
0.71
0.71
0.51
4.0
8.0
Q1
LP5907UVE-3.0/NOPB
DSBGA
YKE
4
250
178.0
8.4
0.71
0.71
0.51
4.0
8.0
Q1
LP5907UVE-3.1/NOPB
DSBGA
YKE
4
250
178.0
8.4
0.71
0.71
0.51
4.0
8.0
Q1
LP5907UVE-3.2/NOPB
DSBGA
YKE
4
250
178.0
8.4
0.71
0.71
0.51
4.0
8.0
Q1
LP5907UVE-3.3/NOPB
DSBGA
YKE
4
250
178.0
8.4
0.71
0.71
0.51
4.0
8.0
Q1
LP5907UVE-4.5/NOPB
DSBGA
YKE
4
250
178.0
8.4
0.71
0.71
0.51
4.0
8.0
Q1
LP5907UVX-1.2/NOPB
DSBGA
YKE
4
3000
178.0
8.4
0.71
0.71
0.51
4.0
8.0
Q1
LP5907UVX-1.8/NOPB
DSBGA
YKE
4
3000
178.0
8.4
0.7
0.7
0.48
4.0
8.0
Q1
LP5907UVX-1.8/NOPB
DSBGA
YKE
4
3000
178.0
8.4
0.71
0.71
0.51
4.0
8.0
Q1
LP5907UVX-2.5/NOPB
DSBGA
YKE
4
3000
178.0
8.4
0.71
0.71
0.51
4.0
8.0
Q1
LP5907UVX-2.8/NOPB
DSBGA
YKE
4
3000
178.0
8.4
0.71
0.71
0.51
4.0
8.0
Q1
LP5907UVX-2.85/NOPB
DSBGA
YKE
4
3000
178.0
8.4
0.7
0.7
0.48
4.0
8.0
Q1
LP5907UVX-2.85/NOPB
DSBGA
YKE
4
3000
178.0
8.4
0.71
0.71
0.51
4.0
8.0
Q1
LP5907UVX-3.0/NOPB
DSBGA
YKE
4
3000
178.0
8.4
0.71
0.71
0.51
4.0
8.0
Q1
LP5907UVX-3.1/NOPB
DSBGA
YKE
4
3000
178.0
8.4
0.71
0.71
0.51
4.0
8.0
Q1
LP5907UVX-3.2/NOPB
DSBGA
YKE
4
3000
178.0
8.4
0.71
0.71
0.51
4.0
8.0
Q1
LP5907UVX-3.3/NOPB
DSBGA
YKE
4
3000
178.0
8.4
0.71
0.71
0.51
4.0
8.0
Q1
LP5907UVX-4.5/NOPB
DSBGA
YKE
4
3000
178.0
8.4
0.71
0.71
0.51
4.0
8.0
Q1
LP5907UVX19/NOPB
DSBGA
YKE
4
3000
178.0
8.4
0.7
0.7
0.48
4.0
8.0
Q1
LP5907UVX19/NOPB
DSBGA
YKE
4
3000
178.0
8.4
0.71
0.71
0.51
4.0
8.0
Q1
LP5907UVX37/NOPB
DSBGA
YKE
4
3000
178.0
8.4
0.71
0.71
0.51
4.0
8.0
Q1
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Aug-2017
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LP5907A28YKMR
DSBGA
YKM
4
3000
220.0
220.0
35.0
LP5907A33YKMR
DSBGA
YKM
4
3000
220.0
220.0
35.0
LP5907MFX-1.2/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP5907MFX-1.5/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP5907MFX-1.8/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP5907MFX-2.5/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP5907MFX-2.8/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP5907MFX-2.85/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP5907MFX-3.0/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP5907MFX-3.1/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP5907MFX-3.2/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP5907MFX-3.3/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP5907MFX-4.5/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LP5907SNX-1.2/NOPB
X2SON
DQN
4
3000
184.0
184.0
19.0
LP5907SNX-1.8/NOPB
X2SON
DQN
4
3000
184.0
184.0
19.0
LP5907SNX-1.9
X2SON
DQN
4
3000
184.0
184.0
19.0
LP5907SNX-2.2/NOPB
X2SON
DQN
4
3000
184.0
184.0
19.0
LP5907SNX-2.5/NOPB
X2SON
DQN
4
3000
184.0
184.0
19.0
LP5907SNX-2.7/NOPB
X2SON
DQN
4
3000
184.0
184.0
19.0
LP5907SNX-2.75
X2SON
DQN
4
3000
202.0
201.0
28.0
Pack Materials-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
3-Aug-2017
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LP5907SNX-2.75
X2SON
DQN
4
3000
184.0
184.0
19.0
LP5907SNX-2.8/NOPB
X2SON
DQN
4
3000
184.0
184.0
19.0
LP5907SNX-2.85/NOPB
X2SON
DQN
4
3000
202.0
201.0
28.0
LP5907SNX-2.85/NOPB
X2SON
DQN
4
3000
184.0
184.0
19.0
LP5907SNX-2.9/NOPB
X2SON
DQN
4
3000
184.0
184.0
19.0
LP5907SNX-3.0/NOPB
X2SON
DQN
4
3000
184.0
184.0
19.0
LP5907SNX-3.1/NOPB
X2SON
DQN
4
3000
184.0
184.0
19.0
LP5907SNX-3.2/NOPB
X2SON
DQN
4
3000
184.0
184.0
19.0
LP5907SNX-3.3/NOPB
X2SON
DQN
4
3000
184.0
184.0
19.0
LP5907SNX-4.0/NOPB
X2SON
DQN
4
3000
184.0
184.0
19.0
LP5907SNX-4.5/NOPB
X2SON
DQN
4
3000
184.0
184.0
19.0
LP5907UVE-1.2/NOPB
DSBGA
YKE
4
250
210.0
185.0
35.0
LP5907UVE-1.8/NOPB
DSBGA
YKE
4
250
210.0
185.0
35.0
LP5907UVE-2.8/NOPB
DSBGA
YKE
4
250
210.0
185.0
35.0
LP5907UVE-2.85/NOPB
DSBGA
YKE
4
250
210.0
185.0
35.0
LP5907UVE-3.0/NOPB
DSBGA
YKE
4
250
210.0
185.0
35.0
LP5907UVE-3.1/NOPB
DSBGA
YKE
4
250
210.0
185.0
35.0
LP5907UVE-3.2/NOPB
DSBGA
YKE
4
250
210.0
185.0
35.0
LP5907UVE-3.3/NOPB
DSBGA
YKE
4
250
210.0
185.0
35.0
LP5907UVE-4.5/NOPB
DSBGA
YKE
4
250
210.0
185.0
35.0
LP5907UVX-1.2/NOPB
DSBGA
YKE
4
3000
210.0
185.0
35.0
LP5907UVX-1.8/NOPB
DSBGA
YKE
4
3000
220.0
220.0
35.0
LP5907UVX-1.8/NOPB
DSBGA
YKE
4
3000
210.0
185.0
35.0
LP5907UVX-2.5/NOPB
DSBGA
YKE
4
3000
210.0
185.0
35.0
LP5907UVX-2.8/NOPB
DSBGA
YKE
4
3000
210.0
185.0
35.0
LP5907UVX-2.85/NOPB
DSBGA
YKE
4
3000
220.0
220.0
35.0
LP5907UVX-2.85/NOPB
DSBGA
YKE
4
3000
210.0
185.0
35.0
LP5907UVX-3.0/NOPB
DSBGA
YKE
4
3000
210.0
185.0
35.0
LP5907UVX-3.1/NOPB
DSBGA
YKE
4
3000
210.0
185.0
35.0
LP5907UVX-3.2/NOPB
DSBGA
YKE
4
3000
210.0
185.0
35.0
LP5907UVX-3.3/NOPB
DSBGA
YKE
4
3000
210.0
185.0
35.0
LP5907UVX-4.5/NOPB
DSBGA
YKE
4
3000
210.0
185.0
35.0
LP5907UVX19/NOPB
DSBGA
YKE
4
3000
220.0
220.0
35.0
LP5907UVX19/NOPB
DSBGA
YKE
4
3000
210.0
185.0
35.0
LP5907UVX37/NOPB
DSBGA
YKE
4
3000
210.0
185.0
35.0
Pack Materials-Page 4
PACKAGE OUTLINE
YKE0004
DSBGA - 0.445mm max height
SCALE 12.000
DIE SIZE BALL GRID ARRAY
B
A
E
BALL A1
CORNER
D
0.445 MAX
C
SEATING PLANE
BALL TYP
0.18
0.14
0.35
TYP
B
0.35
TYP
A
D: Max = 0.675 mm, Min =0.615 mm
E: Max = 0.675 mm, Min =0.615 mm
4X
0.005
0.225
0.195
C A
1
2
B
4220102/A 11/2014
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
www.ti.com
EXAMPLE BOARD LAYOUT
YKE0004
DSBGA - 0.445mm max height
DIE SIZE BALL GRID ARRAY
(0.35) TYP
4X
0.18 0.02
A
SYMM
(0.35) TYP
B
1
2
SYMM
LAND PATTERN EXAMPLE
SCALE:40X
( 0.18)
METAL
0.04 MAX
METAL UNDER
SOLDER MASK
0.04 MIN
( 0.18)
SOLDER MASK
OPENING
SOLDER MASK
OPENING
NON-SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK
DEFINED
SOLDER MASK DETAILS
NOT TO SCALE
4220102/A 11/2014
NOTES: (continued)
3. Final dimensions may vary due to manufacturing tolerance considerations and also routing constraints.
Refer to Texas Instruments Literature No. SNVA009 (www.ti.com/lit/snva009).
www.ti.com
EXAMPLE STENCIL DESIGN
YKE0004
DSBGA - 0.445mm max height
DIE SIZE BALL GRID ARRAY
(0.35) TYP
4X ( 0.21)
(R0.05) TYP
A
SYMM
(0.35)
TYP
B
1
2
SYMM
METAL
TYP
SOLDER PASTE EXAMPLE
BASED ON 0.075 - 0.1mm THICK STENCIL
SCALE:40X
4220102/A 11/2014
NOTES: (continued)
4. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release.
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s noncompliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated