MOP10 MOP10W SERIES DC-DC CONVERTER 2:1 & 4:1 WIDE INPUT RANGE UP TO 10.05 WATTS FEATURES APPLICATIONS • REINFORCED INSULATION FOR 300VAC WORKING VOLTAGE • CLEARANCE AND CREEPAGE DISTANCE :6.6mm/2MOOP • 3000VAC INPUT TO OUTPUT 2MOOP ISOLATION • BUILT-IN EMI CLASS A FILTER • 2µA PATIENT LEAKAGE CURRENT • ANSI/AAMI ES60601-1, EN60601-1, IEC60601-1, UL60950-1, EN60950-1, & IEC60950-1 SAFETY APPROVALS • CE MARKED • COMPLIANT TO RoHS II & REACH 3000VAC ISOLATION UVP OCP MEDICAL EQUIPMENT TELECOM/DATACOM INDUSTRY CONTROL SYSTEM MEASUREMENT EQUIPMENT SEMICONDUCTOR EQUIPMENT PV POWER SYSTEM IGBT GATE DRIVER LOW STANDBY POWER OVP SCP TECHNICAL SPECIFICATION All specifications are typical at nominal input, full load and 25ºC otherwise noted Model Number MOP10-05S3P3A/B MOP10-05S05A/B MOP10-05S12A/B MOP10-05S15A/B MOP10-05S24A/B MOP10-05D05A/B MOP10-05D12A/B MOP10-05D15A/B MOP10-12S3P3A/B MOP10-12S05A/B MOP10-12S12A/B MOP10-12S15A/B MOP10-12S24A/B MOP10-12D05A/B MOP10-12D12A/B MOP10-12D15A/B MOP10-24S3P3A/B MOP10-24S05A/B MOP10-24S12A/B MOP10-24S15A/B MOP10-24S24A/B MOP10-24D05A/B MOP10-24D12A/B MOP10-24D15A/B MOP10-48S3P3A/B MOP10-48S05A/B MOP10-48S12A/B MOP10-48S15A/B MOP10-48S24A/B MOP10-48D05A/B MOP10-48D12A/B MOP10-48D15A/B 1 Input Range Output Voltage Output Current @ Full Load Input Current @ No Load Efficiency Maximum Capacitor Load VDC 4.5 ~9 4.5 ~9 4.5 ~9 4.5 ~9 4.5 ~9 4.5 ~9 4.5 ~9 4.5 ~9 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 VDC 3.3 5 12 15 24 ±5 ±12 ±15 3.3 5 12 15 24 ±5 ±12 ±15 3.3 5 12 15 24 ±5 ±12 ±15 3.3 5 12 15 24 ±5 ±12 ±15 mA 2500 2000 830 670 416 ±1000 ±416 ±333 2500 2000 830 670 416 ±1000 ±416 ±333 2500 2000 830 670 416 ±1000 ±416 ±333 2500 2000 830 670 416 ±1000 ±416 ±333 mA 10 10 20 20 20 25 25 25 10 10 10 10 10 10 10 10 6 6 6 6 6 6 6 6 4 4 4 4 4 4 4 4 % 80 84 86.5 87 85.5 83 85.5 86.5 83 85.5 88 89 89 84 89 88 83 86.5 89 89 89 85 89 88 82.5 86.5 89 89 88.5 85 88 88 µF 3000 2500 430 350 125 ± 1440 ± 250 ± 180 3000 2500 430 350 125 ± 1440 ± 250 ± 180 3000 2500 430 350 125 ± 1440 ± 250 ± 180 3000 2500 430 350 125 ± 1440 ± 250 ± 180 www.PDUKE.com 2014/07/25 Model Number MOP10-24S3P3WA/B MOP10-24S05WA/B MOP10-24S12WA/B MOP10-24S15WA/B MOP10-24S24WA/B MOP10-24D05WA/B MOP10-24D12WA/B MOP10-24D15WA/B MOP10-48S3P3WA/B MOP10-48S05WA/B MOP10-48S12WA/B MOP10-48S15WA/B MOP10-48S24WA/B MOP10-48D05WA/B MOP10-48D12WA/B MOP10-48D15WA/B Input Range Output Voltage Output Current @ Full Load Input Current @ No Load Efficiency Maximum Capacitor Load VDC 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 VDC 3.3 5 12 15 24 ±5 ±12 ±15 3.3 5 12 15 24 ±5 ±12 ±15 mA 2500 2000 830 670 416 ±1000 ±416 ±333 2500 2000 830 670 416 ±1000 ±416 ±333 mA 6 6 6 6 6 6 6 6 4 4 4 4 4 4 4 4 % 83 86.5 89 89 89 85 89 88 82.5 86.5 89 89 88.5 85 88 88 µF 3000 2500 430 350 125 ± 1440 ± 250 ± 180 3000 2500 430 350 125 ± 1440 ± 250 ± 180 P T Remote On/Off Option Trim Option PART NUMBER STRUCTURE MOP10 - Series name 48 S 05 Input Voltage (VDC) Output Quantity Output Voltage (VDC) 4.5~9 9~18 18~36 36~75 S: Single 05: 12: 24: 48: D: Dual MOP10 - Series name 3P3: 05: 12: 15: 24: 3.3 5 12 15 24 A Input Range Pin Connection Option : 2:1 W: 4:1 A: A type(Standard) B: B type : No On/Off control P: Remote On/Off (Only for B type Pin connection) : No Trim T: Trim (Only for B type Pin connection) 05: ±5 12: ±12 15: ±15 48 S 05 W A Input Voltage (VDC) Output Quantity Output Voltage (VDC) Input Range Pin Connection Option 24: 9~36 48: 18~75 S: Single : 2:1 W: 4:1 A: A type(Standard) B: B type D: Dual - 3P3: 05: 12: 15: 24: 05: 12: 15: 3.3 5 12 15 24 ±5 ±12 ±15 INPUT SPECIFICATIONS Parameter Conditions 2 www.PDUKE.com - P T Remote On/Off Option Trim Option : No On/Off control P: Remote On/Off (Only for B type Pin connection) Min. Typ. : No Trim T: Trim (Only for B type Pin connection) Max. Unit 2014/07/25 Operating input voltage range 2:1 (W) 4:1 Start-up voltage 2:1 (W) 4:1 Shutdown voltage 2:1 (W) 4:1 Start up time Input surge voltage Input filter Remote ON/OFF (Only for B-type Pin connection option) Constant resistive load 3 second, max. 2:1 3 second, max. (W) 4:1 DC-DC ON DC-DC OFF Input current of Ctrl pin Remote off input current Referenced to -Vin pin OUTPUT SPECIFICATIONS Parameter Conditions Voltage accuracy Line regulation Low Line to High Line at Full Load Load regulation No Load to Full Load Cross regulation Voltage adjustability Asymmetrical load 25%/100% FL Single output (Only for B-type Pin connection option) Dual output Measured by 20MHz bandwidth With a 10µF/25V X7R MLCC Ripple and noise With a 4.7µF/50V X7R MLCC Temperature coefficient Transient response recovery time Over voltage protection 5 12 24 48 24 48 Over load protection Short circuit protection -0.5 Min. 1 minute VDC VDC VDC VDC VDC VDC ms 16 25 VDC 50 100 50 VDC 100 Pi type OPEN or 0 ~ 1.2VDC 2.2 ~ 12VDC 1 mA 2.5 mA Typ. -1.0 -0.2 -0.5 -0.2 -1.0 -5.0 -10 -10 -10 3.3Vout, 5Vout 12Vout, 15Vout 24Vout Max. Unit +1.0 +0.2 +0.5 +0.2 +1.0 +5.0 +10 +20 +10 % % % % % % 30 40 50 mVp-p +0.02 %/ºC µs 250 3.3Vout 5Vout 12Vout 15Vout 24Vout 5Vout 12Vout 15Vout % of Iout rated; Hiccup mode GENERAL SPECIFICATIONS Parameter 9 18 36 75 36 75 4.5 9 18 36 9 18 4 8 16 33 8 16 30 30 -0.02 Dual 3 Single Dual Single Dual Dual 3.3Vout, 5Vout, 12Vout 15Vout, 24Vout ±5Vout, ±12Vout, ±15Vout 4.5 9 18 36 9 18 25% load step change Single Isolation voltage Isolation capacitance Leakage current Switching frequency 5Vin(nom) 12Vin(nom) 24Vin(nom) 48Vin(nom) 24Vin(nom) 48Vin(nom) 5Vin(nom) 12Vin(nom) 24Vin(nom) 48Vin(nom) 24Vin(nom) 48 Vin(nom) 5Vin(nom) 12Vin(nom) 24Vin(nom) 48Vin(nom) 24Vin(nom) 48Vin(nom) Power up Remote ON/OFF 5Vin(nom) 12Vin(nom) 24Vin(nom) 48Vin(nom) 24Vin(nom) 48Vin(nom) 3.7 5.6 13.5 18.3 29.1 5.6 13.5 17.0 5 7.0 16 22.0 34.5 7.0 18.2 22.0 VDC VDC 150 % Continuous, automatics recovery Conditions Input to Output Min. Typ. Max. Unit 12 17 2 330 VAC pF µA kHz 3000 240VAC,60Hz 270 www.PDUKE.com 300 2014/07/25 Clearance/Creepage Safety approvals Case material Base material Potting material Weight MTBF 6.6 MIL-HDBK-217F, Full load ENVIRONMENTAL SPECIFICATIONS Parameter Operating ambient temperature Storage temperature range Thermal impedance Thermal shock Vibration Relative humidity ESD Radiated immunity Fast transient (2) Surge (2) Conducted immunity Min. Typ. -40 +77 -55 Natural convection (20LFM) EMC SPECIFICATIONS Parameter EMI (1) Conditions Without derating With derating mm ANSI/AAMI ES60601-1 EN60601-1 IEC60601-1 UL60950-1 EN60950-1 IEC60950-1 Non-conductive black plastic Non-conductive black plastic Silicone (UL94 V-0) 14g (0.48oz) 3.849 x 106 hrs Max. ºC ºC ºC ºC/W MIL-STD-810F MIL-STD-810F 5% to 95% RH 18 Conditions Unit +77 +105 +125 Level EN55011,EN55022 and FCC Part 18 Air ± 8kV EN61000-4-2 Contact ± 6kV EN61000-4-3 10 V/m EN61000-4-4 ± 2kV EN61000-4-5 ± 2kV EN61000-4-6 10 Vr.m.s Class A, Class B Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Note: The MOP10 (W) series can meet EMI Class A with no external filter. And Class B only with external components. For further information, please contact with P-DUKE. 2. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The MOP10-05 recommended an aluminum electrolytic capacitor (Nippon Chemi-con KY series, 1000µF/25V). And a reverse diode (Vishay V10P45) to connect in parallel. The MOP10-12&24 recommended an aluminum electrolytic capacitor (Nippon Chemi-con KY series, 470µF/50V). The MOP10-48 recommended an aluminum electrolytic capacitor (Nippon Chemi-con KY series, 330µF/100V). CAUTION: This power module is not internally fused. An input line fuse must always be used. 1. CHARACTERISTIC CURVE MOP10-48S05WA Derating Curve MOP10-48S05WA Efficiency vs. Input Voltage MOP10-48S05WA Efficiency vs. Output Load MECHANICAL DRAWING A TYPE 4 www.PDUKE.com 2014/07/25 PIN CONNECTION PIN 1 11 12 13 15 23 24 1. 2. 3. 4. SINGLE + Vin No pin -Vout +Vout No pin - Vin - Vin DUAL + Vin Common No pin -Vout +Vout - Vin - Vin All dimensions in Inch (mm) Tolerance: X.XX±0.02 (X.X±0.5) X.XXX±0.01 (X.XX±0.25) Pin pitch tolerance ±0.01 (0.25) Pin dimension tolerance ±0.004 (0.1) B TYPE PIN CONNECTION PIN 1 2 10 11 14 16 22 23 SINGLE DUAL CtrlL (Option) / No pin* Ctrl (Option) / No pin* - Vin - Vin Trim (Option) / No pin* Trim (Option) / No pin* No pin / NC ** -Vout +Vout +Vout -Vout Common +Vin +Vin +Vin +Vin * If don’t choose Ctrl or Trim option, there is no pin on the corresponding pin number. ** Pin 11 is “No pin” for MOP10S B-T MOP10S B-PT Pin 11 is “NC” for MOP10S B MOP10S B-P □□ □□□ □□ □□□ 1. 2. 3. 4. All dimensions in Inch (mm) Tolerance: X.XX±0.02 (X.X±0.5) X.XXX±0.01 (X.XX±0.25) Pin pitch tolerance ±0.01 (0.25) Pin dimension tolerance ±0.004 (0.1) □□ □□□ □□ □□□ EXTERNAL OUTPUT TRIMMING Output can be externally trimmed by using the method shown below. ( ) for dual output trim. TRIM UP TRIM DOWN 16(11) 10(10) RU 10(10) 5 www.PDUKE.com RD 14(14) 2014/07/25