Luckylight 4.8mm Round Wide Viewing Angle Type Ultra Red LED Technical Data Sheet Part No.: LL-483VC1C-V1-2B Spec No.: A027X355 Rev No.: V.2 Date: Jun/30/2009 Approved: JoJo Checked: Wu Drawn: YAO Lucky Light Electronics Co., Ltd. Page: 1 OF 7 Http://www.luckylightled.com Luckylight Features: ◇ Choice of various color. ◇ Viewing angle=80°. ◇ High efficiency. ◇ Selected minimum intensities. ◇ Available on tape and reel. ◇ The product itself will remain within RoHS compliant Version. Descriptions: ◇ The series is specially designed for applications requiring higher brightness. ◇ The LED lamps are available with different colors, intensities. Applications: ◇ TV set. ◇ Monitor. ◇ Telephone. ◇ Computer. ◇ Circuit board. ◇ Status indicators. ◇ Commercial use. ◇ Advertising Signs. ◇ Back lighting. Spec No.: A027X355 Rev No.: V.2 Date: Jun/30/2009 Approved: JoJo Checked: Wu Drawn: YAO Lucky Light Electronics Co., Ltd. Page: 2 OF 7 Http://www.luckylightled.com Luckylight Package Dimension: Part No. Chip Material Lens Color Source Color LL-483VC1C-V1-2B AlInGaP Water Clear Ultra Red Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ± 0.25 mm (.010″) unless otherwise noted. 3. Protruded resin is 1.00 mm (.039″) max. 4. Specifications are subject to change without notice. Spec No.: A027X355 Rev No.: V.2 Date: Jun/30/2009 Approved: JoJo Checked: Wu Drawn: YAO Lucky Light Electronics Co., Ltd. Page: 3 OF 7 Http://www.luckylightled.com Luckylight Absolute Maximum Ratings at Ta=25℃ Parameters Symbol Max. Unit Power Dissipation PD 62 mW Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) IFP 100 mA Continuous Forward Current IF 25 mA Reverse Voltage VR 5 V Operating Temperature Range Topr -40℃ to +85℃ Storage Temperature Range Tstg -40℃ to +100℃ Lead Soldering Temperature [4mm (.157″) From Body] Tsld 260℃ for 5 Seconds Electrical Optical Characteristics at Ta=25℃ Parameters Symbol Min. Typ. Max. Unit Test Condition IV 210 350 --- mcd IF=20mA 2θ1/2 --- 80 --- Deg (Note 2) Peak Emission Wavelength λp --- 632 --- nm IF=20mA Dominant Wavelength λd --- 624 --- nm IF=20mA Spectrum Radiation Bandwidth Δλ --- 20 --- nm IF=20mA Forward Voltage VF 1.60 2.00 2.50 V IF=20mA Reverse Current IR --- --- 10 µA VR=5V Luminous Intensity (Note 1)* Viewing Angle* Notes: 1. Luminous Intensity Measurement allowance is ± 10%. 2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 3. The dominant wavelength (λd) is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. Spec No.: A027X355 Rev No.: V.2 Date: Jun/30/2009 Approved: JoJo Checked: Wu Drawn: YAO Lucky Light Electronics Co., Ltd. Page: 4 OF 7 Http://www.luckylightled.com Luckylight Typical Electrical / Optical Characteristics Curves (25℃ Ambient Temperature Unless Otherwise Noted) Forward Current & Forward Voltage Ta=25℃ Ta=25℃ Forward Current IF (mA) 100 75 50 25 0 300 400 500 600 700 Wavelength p (nm) Luminous Intensity & Ambient Temperature 1000 100 10 1 -60 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (℃) 50 40 30 20 10 0 1.4 1.6 1.8 2.0 2.2 2.4 2.6 Forward Voltage VF (V) 800 Luminous Intensity & Forward Current Relative Luminous Intensity (%) Relative Luminous Intensity (%) Relative Luminous Intensity (%) Spectrum Distribution Ta=25℃ 1000 100 10 1 0 10 Forward Current Derating Curve Forward Current IF (mA) f=1KHz Duty=1/10 1 2 3 10 10 10 Forward Current IF (mA) Radiation Diagram 50 o 0 o 10 Ta=25℃ o 20 o 30 40 o 40 30 25 20 1.0 0.9 o 0.8 10 0 o 50 0.7 0 20 40 60 80 100 Ambient Temperature Ta (℃) 0.5 0.3 0.1 0 0.2 0.4 0.6 Spec No.: A027X355 Rev No.: V.2 Date: Jun/30/2009 Approved: JoJo Checked: Wu Drawn: YAO Lucky Light Electronics Co., Ltd. 60 o 70 o 80o 90 Page: 5 OF 7 Http://www.luckylightled.com Luckylight Reliability Test Items And Conditions: The reliability of products shall be satisfied with items listed below: Confidence level: 90%. LTPD: 10%. 1) Test Items and Results: Test Item Resistance to Soldering Heat Solder ability Thermal Shock Temperature Cycle Moisture Resistance Cycle High Temperature Storage Terminal Strength (Pull test) Terminal Strength (bending test) Temperature Humidity Storage Low Temperature Storage Steady State Operating Life Steady State Operating Life of High Humidity Heat Steady State Operating Life of Low Temperature Standard Test Method JEITA ED-4701 300 302 JEITA ED-4701 300 303 JEITA ED-4701 300 307 JEITA ED-4701 100 105 JEITA ED-4701 200 203 JEITA ED-4701 200 201 JEITA ED-4701 400 401 JEITA ED-4701 400 401 JEITA ED-4701 100 103 JEITA ED-4701 200 202 Test Conditions Note Number of Damage d Tsld=260±5℃, 10sec 3mm from the base of the epoxy bulb Tsld=235±5℃, 5sec(using flux) 1 time 0/100 1time over 95% 0/100 0℃~100℃ 15sec, 15sec 100 cycles 0/100 100 cycles 0/100 10 cycles 0/100 Ta=100℃ 1000hrs 0/100 Load 10N (1kgf) 10±1sec Load 5N (0.5kgf) 0°~90°~0° bend 2 times No noticeable damage No noticeable damage Ta=60℃, RH=90% 1000hrs 0/100 Ta=-40℃ 1000hrs 0/100 Ta=25℃, IF＝30mA 1000hrs 0/100 Ta=60℃, RH=90%, IF=30mA 500hrs 0/100 Ta=-30℃, IF＝20mA 1000hrs 0/100 -40℃~25℃~100℃~25℃ 30min,5min,30min,5min 25℃~65℃~-10℃ 90%RH 24hrs/1cycle 0/100 0/100 2) Criteria For Judging The Damage: Item Symbol Test Conditions Forward Voltage VF Reverse Current Luminous Intensity Criteria for Judgment Min Max IF＝20mA --- F.V.*)×1.1 IR VR=5V --- F.V.*)×2.0 IV IF＝20mA F.V.*)×0.7 --- *) F.V.: First Value. Spec No.: A027X355 Rev No.: V.2 Date: Jun/30/2009 Approved: JoJo Checked: Wu Drawn: YAO Lucky Light Electronics Co., Ltd. Page: 6 OF 7 Http://www.luckylightled.com Luckylight Please read the following notes before using the product: 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 3. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 260℃ for 5 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 4. Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. Spec No.: A027X355 Rev No.: V.2 Date: Jun/30/2009 Approved: JoJo Checked: Wu Drawn: YAO Lucky Light Electronics Co., Ltd. Page: 7 OF 7 Http://www.luckylightled.com