MIC GBLA04 Single-phase glass passivated bridge rectifier Datasheet

SINGLE-PHASE GLASS PASSIVATED BRIDGE RECTIFIER
CURRENT
4.0 Amperes
FEATURES
+
1.9 - 2.5
~
~
2.03 - 2.41
0.9 - 1.1
•
•
Case: molded plastic body
Terminal: Plated leads solderable per MIL-STD-750
Method 2026
Mounting position: Any
Weight: 0.071 ounce,2.0 gram
4.8 - 5.3
0.46 - 0.56
0.80 - 1.08
MECHANICAL DATA
•
•
~
10.4 - 10.7
O
17 - 18.2
•
20.7×45
1.5 - 2.03
•
•
•
•
20.7 - 20.9
Plastic package has Underwriters Laboratory
Flammability Glassification 94V-0
Glass passivated chip junctions
High case dielectric strength
High surge current capability
Ideal for printed circuit boards
High temperature soldering guaranteed 260℃/10
seconds, 0.375”(9.5mm) lead length,5 lbs. (2.3kg) tension
3.25 - 3.56
•
50 to 1000 Volts
VOLTAGE RANGE
GBLA005 THRU GBLA10
Dimensions in inches and (millimeters)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
•
•
•
Ratings at 25℃ ambient temperature unless otherwise specified
Single Phase, half wave, 60Hz, resistive or inductive load
For capacitive load derate current by 20%
GBLA GBLA
SYMBOLS
01
005
Maximum Reverse Peak Repetitive Voltage
VRRM
50
100
Maximum RMS Voltage
VRMS
35
70
Maximum DC Blocking Voltage
VDC
50
100
Maximum Average Forward
Rectified Output Current, At
T C=50℃
TA=40℃
Peak Forward Surge Current
8.3ms single half sine wave superimposed on
rated load (JEDEC Method)
Rating for Fusing (t<8.3ms)
Maximum Instantaneous Forward Voltage drop
Per Bridge element 4.0A
TA=25℃
Maximum Reverse Current at rated
DC blocking voltage per element
TA=125℃
Typical Junction Capacitance per leg (Note 3)
Typical Thermal Resistance (Note 1)
Typical Thermal Resistance (Note 2)
Operating and Storage Temperature Range
I(AV)
GBLA
02
200
140
200
GBLA
GBLA
GBLA
GBLA
04
400
280
400
4.0(Note 1)
3.0(Note 2)
06
600
420
600
08
800
560
800
10
1000
700
1000
UNIT
Volts
Volts
Volts
Amps
IFSM
120
Amps
I2 t
60
A2s
VF
1.0
Volts
IR
5.0
500
μA
CJ
RJA
RJL
TJ ,TSTG
95.0
40.0
22
10
(-55 to +150)
Notes: 1. Unit mounted on 3.0×3.0×0.11” thick (7.5×7.5×0.3cm) AL. plate
2. Unit mounted on P.C.B. at 0.375” (9.5mm) lead lengh and 0.5×0.5”(12×12mm) copper pads
3. Measured at 1.0MHz and applied reverse voltage of 4.0 V
E-mail: [email protected]
Web Site: www.cnmic.com
pF
℃/W
℃/W
℃
SINGLE-PHASE GLASS PASSIVATED BRIDGE RECTIFIER
50 to 1000Volts
VOLTAGE RANGE
GBLA005 THRU GBLA10
CURRENT
4.0 Ampere
RATINGS AND CHARACTERISTIC CURVES GBLA005 THRU GBLA10
FIG. 2- MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT PER LEG
5.0
150
60 Hz Resistive or Inductive Load
PEAK FORWARD SURGE,
CURRENT, (A)
AVERAGE FORWARD OUTPUT,CURRENT
(A)
FIG. 1- DERATING CURVE
OUTPUT RECTIFIED CURRENT
Heat- SinkMounting
3.0×3.0×0.11"Thick
(7.5×7.5×0.3cm )
Aluminum Plate
4.0
3.0
2.0
P.C.B. Mounting
0.47×0.47"( 12×12mm)
Copper pads with 0.375"
(9.5mm) lead length
1.0
TJ = T J max.
Single Sine-Wave
(JEDEC Method)
100
50
1.0 CYCLE
0
0
100
50
0
150
FIG. 4- TYPICAL REVERSE LEAKAGE
CHARACTERISTICS PER LEG
100
500
INSTANTANEOUS REVERSE
CURRENT, (A)
INSTANTANEOUS FORWARD
CURRENT, (A)
100
NUMBER OF CYCLES AT 60 Hz
FIG. 3- TYPICAL FORWORD VOLTAGE
CHARACTERISTICS PER LGE
10
1
0.1
TJ=25℃
Pulse width=300 μs
1% Duty Cycle
0.4
0.6
0.8
1.0
1.2
1.4
100
10
0.1
0.01
1.6
TRANSIENT THERMAL IMPEDANCE
(℃/W)
100
50-400V
600-1000V
REVRESE VOLTAGE,(V)
E-mail: [email protected]
60
40
80
100
100
T j =25℃
f=1.0MHz
Vsig=50mVp-p
10
20
FIG. 6- TYPICAL TRANSIENT THERMAL
IMPEDANCE PER LEG
1000
1
0
PERCENT OF RATED PEAK REVERSE VOLTAGE,(V)
FIG. 5- TYPICAL JUNCTION CAPACITANCE
PER LEG
0.1
50-400V
600-1000V
1
INSTANTANEOUS FORWARD VOLTAGE,(V)
10
TA =125℃
TA =25℃
0.01
JUNCTION CAPACITANCE, (pF)
10
1
AMBIENT TEMPERATURE, ℃
100
10
1
0.1
0.01
0.1
1
10
T, HEATING TIME (SEC.)
Web Site: www.cnmic.com
100
Similar pages