AH3775 HIGH-VOLTAGE MEDIUM-SENSITIVITY HALL EFFECT LATCH Description Pin Assignments The AH3775 is a high-voltage medium-sensitivity Hall Effect latch IC designed for commutation of brushless DC motors, flow meters, linear encoders and position sensors in industrial and consumer home appliances and personal care applications. To support wide range of demanding applications, the design is optimized to operate over the supply range of 3.0V to 28V. With chopper stabilized architecture and an internal bandgap regulator to provide temperature compensated supply for internal circuits, the AH3775 provides a reliable solution over the whole operating range. For robustness and protection, the device has a reverse blocking diode with a Zener clamp on the supply. The output has an overcurrent limit and a Zener clamp. (Top View) 3 OUTPUT GND 2 1 VDD SC59 and SOT23 The single, open drain output can be switched on with South pole of sufficient strength and switched off with North pole of sufficient strength. When the magnetic flux density (B) perpendicular to the package is larger than the operate point (BOP) the output is switched (Top View) on (pulled low). The output is held latched until magnetic flux density reverses and becomes lower than the release point (BRP). 3. OUTPUT The magnetic operating and release polarity is opposite for SOT23 and SC59 packages. SOT23 and SIP-3 packages will require south pole to the part marking side to operate while SC59 will require south pole to the non-part marking side. 1. VDD 2. GND SIP-3 Features Applications • Bipolar Latch Operation (South Pole: On, North Pole: off) • Brushless DC Motor Commutation • 3.0V to 28V Operating Voltage Range • Revolution Per Minute (RPM) Measurement • Medium Sensitivity: BOP and BRP of +70G and -70G Typical • Flow Meters • Single, Open-Drain Output with Overcurrent Limit • Angular and Linear Encoder and Position Sensors • Chopper Stabilized Design Provides: • Contactless Commutation, Speed Measurement and Angular - Superior Temperature Stability Position Sensing/Indexing in Consumer Home Appliances, Office - Minimal Switch Point Drift Equipments and Industrial Applications - Enhanced Immunity to Stress • Good RF Noise Immunity • Reverse Blocking Diode and Zener Clamp on Supply • -40C to +125C Operating Temperature • ESD (HBM): 6kV • Industry Standard SC59, SOT23 and SIP-3 Packages • Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2) • Halogen and Antimony Free. “Green” Device (Note 3) Notes: 1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant. 2. See http://www.diodes.com/quality/lead_free.html for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green" and Lead-free. 3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and <1000ppm antimony compounds. AH3775 Document number: DS37900 Rev. 1 - 2 1 of 14 www.diodes.com September 2015 © Diodes Incorporated AH3775 Typical Applications Circuit 3.0V to 28V VDD RL OUTPUT AH3775 CIN GND Note: 4. CIN is for power stabilization and to strengthen the noise immunity, the recommended capacitance is 10nF ~ 100nF. RL is the pull-up resistor. Pin Descriptions Package: SC59, SOT23 and SIP-3 Pin Number Pin Name 1 VDD 2 3 GND OUTPUT Function Power Supply Input Ground Output Pin Functional Block Diagram VDD Power switch To All Subcircuits Amp Low-Pass Filter Sample and Hold Dynamic Offset Cancellation Amp OUTPUT Control Current Limit GND AH3775 Document number: DS37900 Rev. 1 - 2 2 of 14 www.diodes.com September 2015 © Diodes Incorporated AH3775 Absolute Maximum Ratings (Notes 5 & 6) (@TA = +25°C, unless otherwise specified.) Symbol VDD VDDR VOUT_MAX IOUT IOUT_R B Reverse Output Current Magnetic Flux Density PD Value 32 -32 32V 60 Unit V V V mA -50 mA Unlimited 550 230 -65 to +165 +150 6 SIP-3 SC59 and SOT23 Package Power Dissipation Ts TJ ESD Notes: Characteristic Supply Voltage (Note 6) Reverse Supply Voltage Output off Voltage (Note 6) Continuous Output Current Storage Temperature Range Maximum Junction Temperature Electrostatic Discharge Withstand Capability - Human Body Model mW mW °C °C kV 5. Stresses greater than the 'Absolute Maximum Ratings' specified above may cause permanent damage to the device. These are stress ratings only; functional operation of the device at these or any other conditions exceeding those indicated in this specification is not implied. Device reliability may be affected by exposure to absolute maximum rating conditions for extended periods of time. 6. The absolute maximum VDD of 32V is a transient stress rating and is not meant as a functional operating condition. It is not recommended to operate the device at the absolute maximum rated conditions for any period of time. Recommended Operating Conditions (@TA = -40°C to +125°C, unless otherwise specified.) Symbol VDD TA Rating Unit Supply Voltage Parameter Operating 3.0 to 28V V Operating Temperature Range Operating -40 to +125 °C Electrical Characteristics Symbol VOUT_ON IOUT_OFF IDD IDD_R tST fc td tr tf IOCL VZ Notes: Conditions (Notes 7 & 8) (@TA = -40°C to +125°C, VDD = 3V to 28V, unless otherwise specified.) Parameter Output oN Voltage Output Leakage Current Supply Current Reverse Battery Current Device start-up time Chopping Frequency The time delay from magnetic threshold reached to the start of the output rise or fall Output Rising Time (external pull-up resistor RL and load capacitance dependent) Output Falling Time (Internal switch resistance and load capacitance dependent) Output Current Limit Zener clamp voltage Conditions IOUT = 20mA, B > BOP VOUT = 28V, B < Brp, Output off Output open, TA = +25°C Output open, TA = -40°C to +125°C VDD = -18V, TA = -40°C to +125°C VDD = -28V, TA = -40°C to +125°C VDD >= 3V, B > Bop (Note 7) VDD = 3V to 28V Min - Typ 0.2 <0.1 2.7 -0.01 -0.01 10 800 Max 0.4 10 3 4 1 1.5 - Unit V µA mA mA mA mA µs kHz (Note 9) - 3.75 - µs RL =1kΩ, CL = 20pF - 0.2 1 µs RL =1kΩ, CL = 20pF - 0.1 1 µs B> BOP, (Note 10 ) IDD = 5mA 30 28 - 55 - mA V 7. When power is initially turned on, VDD must be within its correct operating range (3.0V to 28V) to guarantee the output sampling. The output state is valid after the start-up time of 10us typical from the operating voltage reaching 3V. 8. Typical values are defined at TA = +25C, VDD = 12V. Maximum and minimum values over the operating temperature range is not tested in production but guaranteed by design, process control and characterization 9. Guaranteed by design, process control and characterization, Not tested in production. 10. The device will limit the output current IOUT to current limit of IOCL AH3775 Document number: DS37900 Rev. 1 - 2 3 of 14 www.diodes.com September 2015 © Diodes Incorporated AH3775 Magnetic Characteristics (Notes 11 &12) (TA = -40°C to +125°C, VDD = 3.0V to 28V, unless otherwise specified) Symbol Parameter Conditions BOP (South pole to part marking side for SOT23 and SIP-3 packages; South pole to the non-part marking side for SC59 package. See diagram below) Operation Point BRP (North pole to part marking side for SOT23 and SIP-3 packages; North pole to the non-part marking side for SC59 package. See diagram below) Release Point BHY (|BOPX|-|BRPX|) Hysteresis (Note 13) Notes: (1mT=10 Gauss) Max Unit Min Typ VDD = 12V, TA = +25°C - 70 - TA = -40°C to +125°C 50 70 90 VDD = 12V, TA = +25°C - -70 - TA = -40°C to +125°C -90 -70 -50 VDD = 12V, TA = +25°C - 140 - TA = -40°C to +125°C 100 140 180 Gauss 11. When power is initially turned on, VDD must be within its correct operating range (3.0V to 28V) to guarantee the output sampling. The output state is valid after the start-up time of 10µs typical from the operating voltage reaching 3V. 12. Typical values are defined at TA = +25°C, VDD = 12V. Maximum and minimum values over the operating temperature range is not tested in production but guaranteed by design, process control and characterization 13. Maximum and minimum hysteresis is guaranteed by design, process control and characterization. Output VDD ( Output Voltage ) (off-state) Bhy Turn off Turn on (on-state) VOUT_ON = VOUT(SAT) Brp 0 Bop ( Magnetic Flux Density B ) S S S Part mark Part mark Part mark AH3775 Document number: DS37900 Rev. 1 - 2 N N N (SC59) (SOT23) (SIP-3) 4 of 14 www.diodes.com September 2015 © Diodes Incorporated AH3775 Typical Operating Characteristics Magnetic Operating Switch Points – BOP and BRP 180.0 160.0 140.0 120.0 100.0 80.0 60.0 40.0 20.0 0.0 -20.0 -40.0 -60.0 -80.0 -100.0 -120.0 -140.0 -160.0 -180.0 TA = +25oC Hyst VDD = 3V Hyst Bop Gauss (G) Gauss (G) Bop 180.0 160.0 140.0 120.0 100.0 80.0 60.0 40.0 20.0 0.0 -20.0 -40.0 -60.0 -80.0 -100.0 -120.0 -140.0 -160.0 -180.0 Brp 2 180.0 160.0 140.0 120.0 100.0 80.0 60.0 40.0 20.0 0.0 -20.0 -40.0 -60.0 -80.0 -100.0 -120.0 -140.0 -160.0 -180.0 4 6 8 10 12 14 16 18 20 22 24 26 28 Brp -50 30 -25 0 25 50 75 100 125 150 o Supply Voltage (V) Temperature ( C) Switch Points Bop and Brp vs Supply Voltage Switch Points Bop and Brp vs Temperature VDD = 12V 180.0 160.0 140.0 120.0 100.0 80.0 60.0 40.0 20.0 0.0 -20.0 -40.0 -60.0 -80.0 -100.0 -120.0 -140.0 -160.0 -180.0 Hyst Hyst Bop Gauss (G) Gauss (G) Bop VDD = 28V Brp -50 -25 0 25 50 75 100 125 Brp -50 150 -25 0 25 50 75 100 125 150 o o Temperature ( C) Temperature ( C) Switch Points Bop and Brp vs Temperature Switch Points Bop and Brp vs Temperature Supply Current 4.0 TA = +25 C Supply Current IDD (mA) Supply Current IDD (mA) 5.0 4.0 3.0 2.0 1.0 3.8 3.5 28V 3.3 3.0 2.8 3V 2.5 12V 2.3 2.0 0.0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 Supply Voltage (V) Temperature (oC) Supply Current vs Supply Voltage Supply Current vs Temperature AH3775 Document number: DS37900 Rev. 1 - 2 5 of 14 www.diodes.com September 2015 © Diodes Incorporated AH3775 Typical Operating Characteristics 0.4 Output On Voltage VOUT_ON (V) Output On Voltage VOUT_ON (V) Output Switch On Voltage TA = +25 C 0.3 0.2 0.1 0.0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 0.4 28V 0.3 0.2 3V 12V 0.1 0.0 -50 -40 -30 -20 -10 30 0 10 20 30 40 50 60 70 80 90 100 110 120 130 Temperature (oC) Supply Voltage (V) Output On Voltage vs Temperature Output On Voltage vs Supply Voltage 30.0 Output Leakage Current (nA) Output Leakage Current (nA) Output Switch Leakage Current TA = +25 C 25.0 20.0 15.0 10.0 5.0 300 275 250 225 200 175 28V 150 125 100 12V 75 3V 50 25 0 0.0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 -50 30 -25 0 25 50 75 100 125 150 Temperature (oC) Supply Voltage (V) Output Leakage Current vs Temperature Output Leakage Current vs Supply Voltage 3.0 2.8 750 TA = +25 C Supply Reverse Current (mA) Supply Reverse Current (mA) Supply Reverse Current 2.5 2.3 2.0 1.8 1.5 1.3 1.0 0.8 0.5 0.3 0.0 -30 -28 -26 -24 -22 -20 -18 -16 -14 -12 -10 -8 -6 -4 -2 625 -28V 500 -24V 375 250 -18V 125 0 -50 25 50 75 100 125 150 Temperature ( C) Supply Reverse Current vs Temperature Supply Reverse Current vs Supply Voltage Document number: DS37900 Rev. 1 - 2 0 o Supply Voltage (V) AH3775 -25 6 of 14 www.diodes.com September 2015 © Diodes Incorporated AH3775 Thermal Performance Characteristics (1) Package Type: SC59 and SOT23 TA (°C) 25 50 60 70 80 85 90 100 105 110 120 125 130 140 150 PD (mW) 230 184 166 147 129 120 110 92 83 74 55 46 37 18 0 Power Dissipation Curve Power Dissipation PD (mW) 300 200 100 0 -40 0 25 50 75 100 125 150 Ambient Temperature TA (oC) (2) Package type: SIP-3 TA (°C) 25 50 60 70 80 85 90 100 105 110 120 125 130 140 150 PD (mW) 550 440 396 362 308 286 264 220 198 176 132 110 88 44 0 PD (mW) Power Dissipation Curve 600 500 400 300 200 100 0 -40 0 25 50 75 100 125 150 TA (°C) AH3775 Document number: DS37900 Rev. 1 - 2 7 of 14 www.diodes.com September 2015 © Diodes Incorporated AH3775 Ordering Information AH3775 - XXX - X Packing Package 7 : Tape & Reel A: Ammo Box (Note 14) B: Bulk (Note 15) P : SIP-3 SA : SOT23 W : SC59 Part Number Package Code Packaging AH3775-P-A P SIP-3 Quantity 7” Tape and Reel Part Number Quantity Suffix Bulk Part Number Suffix NA NA NA Ammo Box Quantity Part Number Suffix NA 4,000/Box -A NA AH3775-P-B P SIP-3 1,000 -B NA NA NA AH3775-SA-7 SA SOT23 NA NA 3,000/Tape & Reel -7 NA NA AH3775-W-7 W SC59 NA NA 3,000/Tape & Reel -7 NA NA Notes: 14. Ammo Box is for SIP-3 Spread Lead. 15. Bulk is for SIP-3 Straight Lead. Marking Information (1) Package Type: SOT23 and SC59 ( Top View ) XX Y W X (2) XX : Identification code Y : Year 0 to 9 W : Week : A to Z : 1 to 26 week; a to z : 27 to 52 week; z represents 52 and 53 week X : Internal code Part Number Package Identification Code AH3775 AH3775 SC59 SOT23 YZ ZE Package Type: SIP-3 ( Top View ) Part Number 3775 Y WW X AH3775 Document number: DS37900 Rev. 1 - 2 Y : Year : 0~9 WW : Week : 01~52, "52" represents 52 and 53 week X : Internal Code Part Number Package Identification Code AH3775 SIP-3 3775 8 of 14 www.diodes.com September 2015 © Diodes Incorporated AH3775 Package Outline Dimensions (All dimensions in mm.) Please see AP02002 at http://www.diodes.com/datasheets/ap02002.pdf for the latest version. (1) Package Type: SC59 A SC59 Dim Min Max Typ A 0.35 0.50 0.38 B 1.50 1.70 1.60 C 2.70 3.00 2.80 D 0.95 G 1.90 H 2.90 3.10 3.00 J 0.013 0.10 0.05 K 1.00 1.30 1.10 L 0.35 0.55 0.40 M 0.10 0.20 0.15 N 0.70 0.80 0.75 0° 8° All Dimensions in mm B C G H K J M N L D 0.10/0.20 CL 0.7/0.9 PART MARKING SURFACE 0.595/0.715 Min/Max Die Hall Sensor Pin1 1.3/1.5 Sensor Location AH3775 Document number: DS37900 Rev. 1 - 2 9 of 14 www.diodes.com September 2015 © Diodes Incorporated AH3775 Package Outline Dimensions (cont.) (All dimensions in mm.) Please see AP02002 at http://www.diodes.com/datasheets/ap02002.pdf for the latest version. (2) Package Type: SOT23 All 7° H K1 J K SOT23 Dim Min Max Typ A 0.37 0.51 0.40 B 1.20 1.40 1.30 C 2.30 2.50 2.40 D 0.89 1.03 0.915 F 0.45 0.60 0.535 G 1.78 2.05 1.83 H 2.80 3.00 2.90 J 0.013 0.10 0.05 K 0.890 1.00 0.975 K1 0.903 1.10 1.025 L 0.45 0.61 0.55 L1 0.25 0.55 0.40 M 0.085 0.150 0.110 a 8° All Dimensions in mm GAUGE PLANE 0.25 a M A L C L1 B D F G 0.17/0.37 Min/Max 0.5/0.7 PART MARKING SURFACE Die Hall Sensor Pin1 1.4/1.5 Sensor Location AH3775 Document number: DS37900 Rev. 1 - 2 10 of 14 www.diodes.com September 2015 © Diodes Incorporated AH3775 Package Outline Dimensions (cont.) (All dimensions in mm.) Please see AP02002 at http://www.diodes.com/datasheets/ap02002.pdf for the latest version. (3) Package Type: SIP-3 Bulk Sensor location to be added SIP-3 (Bulk) Dim Min Max A 3.9 4.3 a1 5° Typ a2 5°Typ a3 45° Typ a4 3°Typ B 2.8 3.2 C 1.40 1.60 D 0.33 0.432 E 0.40 0.508 F 0 0.2 G 1.24 1.30 H 2.51 2.57 J 0.35 0.43 L 14.0 15.0 N 0.63 0.84 P 1.55 All Dimensions in mm L a1 J a2 B P N D C a3 A E a4 G H F Min/Max 0.63/0.84 0.27/0.48 1.90/2.10 PART MARKING SURFACE Hall Sensor 1 2 Die 1.05/1.25 PART MARKING SURFACE 3 Sensor Location AH3775 Document number: DS37900 Rev. 1 - 2 11 of 14 www.diodes.com September 2015 © Diodes Incorporated AH3775 Package Outline Dimensions (cont.) (All dimensions in mm.) Please see AP02002 at http://www.diodes.com/datasheets/ap02002.pdf for the latest version. (4) Package Type: SIP-3 Ammo Pack N D EF SIP-3 (Ammo Pack) Dim Min Max A 3.9 4.3 a1 45° Typ a2 3° Typ B 2.8 3.2 C 1.40 1.60 D 0.35 0.41 E 0.43 0.48 F 0 0.2 G 2.4 2.9 N 0.63 0.84 P 1.55 All Dimensions in mm C A G a1 a2 B P Min/Max 0.63/0.84 0.27/0.48 1.90/2.10 Hall Sensor 1 2 Die 1.05/1.25 PART MARKING SURFACE PART MARKING SURFACE 3 Sensor Location AH3775 Document number: DS37900 Rev. 1 - 2 12 of 14 www.diodes.com September 2015 © Diodes Incorporated AH3775 Suggested Pad Layout Please see AP02001 at http://www.diodes.com/datasheets/ap02001.pdf for the latest version. (1) Package Type: SC59 Y Z X (2) Dimensions Value (in mm) Z 3.4 X 0.8 Y 1.0 C 2.4 E 1.35 C E Package Type: SOT23 Dimensions Value (in mm) Z 2.9 X 0.8 Y 0.9 C 2.0 E 1.35 AH3775 Document number: DS37900 Rev. 1 - 2 13 of 14 www.diodes.com September 2015 © Diodes Incorporated AH3775 IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the final and determinative format released by Diodes Incorporated. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2015, Diodes Incorporated www.diodes.com AH3775 Document number: DS37900 Rev. 1 - 2 14 of 14 www.diodes.com September 2015 © Diodes Incorporated