[ /Title (CD74 HC401 5) /Subject (High Speed CMOS Logic Dual 4- CD54HC4015, CD74HC4015 Data sheet acquired from Harris Semiconductor SCHS198C High Speed CMOS Logic Dual 4-Stage Static Shift Register November 1997 - Revised May 2003 Features Description • Maximum Frequency, Typically 60MHz CL = 15pF, VCC = 5V, TA = 25oC The ’HC4015 consists of two identical, independent, 4-stage serial-input/parallel-output registers. Each register has independent Clock (CP) and Reset (MR) inputs as well as a single serial Data input. “Q” outputs are available from each of the four stages on both registers. All register stages are Dtype, master-slave flip-flops. The logic level present at the Data input is transferred into the first register stage and shifted over one stage at each positive- going clock transition. Resetting of all stages is accomplished by a high level on the reset line. • Positive-Edge Clocking • Overriding Reset • Buffered Inputs and Outputs • Fanout (Over Temperature Range) - Standard Outputs . . . . . . . . . . . . . . . 10 LSTTL Loads - Bus Driver Outputs . . . . . . . . . . . . . 15 LSTTL Loads The device can drive up to 10 low power Schottky equivalent loads. The ’HC4015 is an enhanced version of equivalent CMOS types. • Wide Operating Temperature Range . . . -55oC to 125oC • Balanced Propagation Delay and Transition Times Ordering Information • Significant Power Reduction Compared to LSTTL Logic ICs TEMP. RANGE (oC) PACKAGE CD54HC4015F3A -55 to 125 16 Ld CERDIP CD74HC4015E -55 to 125 16 Ld PDIP CD74HC4015M -55 to 125 16 Ld SOIC PART NUMBER • HC Types - 2V to 6V Operation - High Noise Immunity: NIL = 30%, NIH = 30% of VCC at VCC = 5V Pinout CD54HC4015 (CERDIP) CD74HC4015 (PDIP, SOIC) TOP VIEW 2CP 1 16 VCC 2Q3 2 15 2D 1Q2 3 14 2MR 1Q1 4 13 2Q0 1Q0 5 12 2Q1 1MR 6 11 2Q2 1D 7 10 1Q3 GND 8 9 1CP CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures. Copyright © 2003, Texas Instruments Incorporated 1 CD54HC4015, CD74HC4015 Functional Diagram 5 7 1D 4 9 3 1CP 10 6 1MR 1Q0 1Q1 1Q2 1Q3 13 15 2D 12 1 11 2CP 2 14 2MR 2Q0 2Q1 2Q2 2Q3 GND = 8 VCC = 16 TRUTH TABLE INPUTS CP OUTPUTS D R Q0 Q1 Q2 Q3 ↑ l ↑ h L L q’0 q’1 q’2 L H q’0 q’1 q’2 ↓ X L q’0 q’1 q’2 q’3 X X H L L L L H = High Voltage Level h = High Voltage Level One Set-up Time Prior to the Low to High Clock Transition L = Low Voltage Level l = Low Voltage Level One Set-up Time Prior to the Low to High Clock Transition X = Don’t Care. ↑ = Low to High Clock Transition ↓ = High to Low Clock Transition q’n = Lower case letters indicate the state of the referenced output one set-up time prior to the Low to High clock transition. 2 CD54HC4015, CD74HC4015 t6 Absolute Maximum Ratings Thermal Information DC Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 7V DC Input Diode Current, IIK For VI < -0.5V or VI > VCC + 0.5V . . . . . . . . . . . . . . . . . . . . . .±20mA DC Output Diode Current, IOK For VO < -0.5V or VO > VCC + 0.5V . . . . . . . . . . . . . . . . . . . .±20mA DC Output Source or Sink Current per Output Pin, IO For VO > -0.5V or VO < VCC + 0.5V . . . . . . . . . . . . . . . . . . . .±25mA DC VCC or Ground Current, ICC . . . . . . . . . . . . . . . . . . . . . . . . .±50mA Thermal Resistance (Typical, Note 1) θJA (oC/W) E (PDIP) Package . . . . . . . . . . . . . . . . . . . . . . . . . . 67 M (SOIC) Package. . . . . . . . . . . . . . . . . . . . . . . . . . 73 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only) Operating Conditions Temperature Range, TA . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC Supply Voltage Range, VCC HC Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2V to 6V DC Input or Output Voltage, VI, VO . . . . . . . . . . . . . . . . . 0V to VCC Input Rise and Fall Time 2V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000ns (Max) 4.5V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500ns (Max) 6V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400ns (Max) CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. The package thermal impedance is calculated in accordance with JESD 51-7. f DC Electrical Specifications TEST CONDITIONS PARAMETER High Level Input Voltage VI (V) IO (mA) VIH - - 2 1.5 - - 1.5 4.5 3.15 - - 3.15 - 3.15 - V 6 4.2 - - 4.2 - 4.2 - V 2 - - 0.5 - 0.5 - 0.5 V 4.5 - - 1.35 - 1.35 - 1.35 V VIL High Level Output Voltage CMOS Loads VOH - VIH or VIL High Level Output Voltage TTL Loads VOL VIH or VIL Low Level Output Voltage TTL Loads Input Leakage Current Quiescent Device Current -40oC TO 85oC -55oC TO 125oC SYMBOL Low Level Input Voltage Low Level Output Voltage CMOS Loads 25oC VCC (V) - MIN TYP MAX MIN MAX MIN MAX UNITS - 1.5 - V 6 - - 1.8 - 1.8 - 1.8 V -0.02 2 1.9 - - 1.9 - 1.9 - V -0.02 4.5 4.4 - - 4.4 - 4.4 - V -0.02 6 5.9 - - 5.9 - 5.9 - V - - - - - - - - - V -4 4.5 3.98 - - 3.84 - 3.7 - V -5.2 6 5.48 - - 5.34 - 5.2 - V 0.02 2 - - 0.1 - 0.1 - 0.1 V 0.02 4.5 - - 0.1 - 0.1 - 0.1 V 0.02 6 - - 0.1 - 0.1 - 0.1 V - - - - - - - - - V 4 4.5 - - 0.26 - 0.33 - 0.4 V 5.2 6 - - 0.26 - 0.33 - 0.4 V II VCC or GND - 6 - - ±0.1 - ±1 - ±1 µA ICC VCC or GND 0 6 - - 8 - 80 - 160 µA 3 CD54HC4015, CD74HC4015 Prerequisite for Switching Specifications 25oC PARAMETER Maximum Clock Frequency Clock Pulse Width MR Pulse Width MR Recovery Time -40oC TO 85oC -55oC TO 125oC SYMBOL VCC (V) MIN MAX MIN MAX MIN MAX UNITS fMAX 2 6 - 5 - 4 - MHz 4.5 30 - 24 - 20 - MHz 6 35 - 28 - 24 - MHz 2 80 - 100 - 120 - ns 4.5 16 - 20 - 24 - ns 6 14 - 17 - 20 - ns tW tW 2 150 - 190 - 225 - ns 4.5 30 - 38 - 45 - ns 6 26 - 33 - 38 - ns tREC Set-up Time, Data-In to CP tSUL, tSUH Hold Time, Data-In to CP tH 2 50 - 65 - 75 - ns 4.5 10 - 13 - 15 - ns 6 9 - 11 - 13 - ns 2 60 - 75 - 90 - ns 4.5 12 - 15 - 18 - ns 6 10 - 13 - 15 - ns 2 0 - 0 - 0 - ns 4.5 0 - 0 - 0 - ns 6 0 - 0 - 0 - ns Switching Specifications Input tr, tf = 6ns PARAMETER Propagation Delay (Figure 1) Clock to Qn MR to Qn, (Clock High) TEST SYMBOL CONDITIONS tPLH, tPHL tPLH, tPHL CL = 50pF 25oC tPLH, tPHL MIN TYP MAX MIN MAX MIN MAX UNITS - - 175 - 220 - 270 ns 4.5 - - 35 - 44 - 54 ns CL =15pF 5 - 14 - - - - - ns CL = 50pF 6 - - 30 - 37 - 46 ns CL = 50pF 2 - - 275 - 345 - 415 ns 4.5 - - 55 - 64 - 83 ns 25 - - - - - ns CL = 50pF 6 - - 47 - 54 - 71 ns CL = 50pF 2 - - 325 - 400 - 490 ns 4.5 - CL =15pF CL = 50pF Output Transition Time (Figure 1) -55oC TO 125oC 2 CL =15pF MR to Qn, (Clock Low) -40oC TO 85oC VCC (V) tTLH, tTHL CL = 50pF 6 - - 65 - 81 - 98 ns 25 - - - - - ns - 55 - 69 - 83 ns 2 - - 75 - 95 - 110 ns 4.5 - - 15 - 19 - 22 ns 6 - - 13 - 16 - 19 ns CIN CL = 50pF - - - 10 - 10 - 10 pF Maximum Clock Frequency fMAX CL =15pF 5 - 60 - - - - - MHz Power Dissipation Capacitance (Notes 2, 3) CPD CL =15pF 5 - 43 - - - - - pF Input Capacitance NOTES: 2. CPD is used to determine the dynamic power consumption, per shift register. 3. PD = VCC2 fi + ∑ CL VCC2 where fi = Input Frequency, CL = Output Load Capacitance, VCC = Supply Voltage. 4 CD54HC4015, CD74HC4015 Test Circuit and Waveform tfCL trCL CLOCK INPUT VCC 90% 50% 10% GND tH(H) tH(L) VCC DATA INPUT 50% GND tSU(H) tSU(L) tTLH 90% tTHL 90% 50% 10% tPLH tPHL OUTPUT tREM VCC SET, RESET OR PRESET 50% GND IC CL 50pF FIGURE 1. HC SETUP TIMES, HOLD TIMES, REMOVAL TIME, AND PROPAGATION DELAY TIMES FOR EDGE TRIGGERED SEQUENTIAL LOGIC CIRCUITS 5 PACKAGE OPTION ADDENDUM www.ti.com 9-Oct-2007 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty Lead/Ball Finish MSL Peak Temp (3) 5962-8995301EA ACTIVE CDIP J 16 1 TBD A42 SNPB N / A for Pkg Type CD54HC4015F3A ACTIVE CDIP J 16 1 TBD A42 SNPB N / A for Pkg Type CD74HC4015E ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type CD74HC4015EE4 ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type CD74HC4015M ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4015ME4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4015MG4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Telephony www.ti.com/telephony Low Power Wireless www.ti.com/lpw Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2007, Texas Instruments Incorporated