a FEATURES Laser Trimmed to High Accuracy: 2.500 V 6 0.4% 3-Terminal Device: Voltage In/Voltage Out Excellent Temperature Stability: 10 ppm/8C (AD580M, U) Excellent Long-Term Stability: 250 mV (25 mV/Month) Low Quiescent Current: 1.5 mA max Small, Hermetic IC Package: TO-52 Can MIL-STD-883 Compliant Versions Available High Precision 2.5 V IC Reference AD580* FUNCTIONAL BLOCK DIAGRAM PRODUCT DESCRIPTION PRODUCT HIGHLIGHTS The AD580 is a three-terminal, low cost, temperature compensated, bandgap voltage reference which provides a fixed 2.5 V output for inputs between 4.5 V and 30 V. A unique combination of advanced circuit design and laser-wafer trimmed thinfilm resistors provide the AD580 with an initial tolerance of ± 0.4%, a temperature stability of better than 10 ppm/°C and long-term stability of better than 250 µV. In addition, the low quiescent current drain of 1.5 mA max offers a clear advantage over classical Zener techniques. 1. Laser-trimming of the thin-film resistors minimizes the AD580 output error. For example, the AD580L output tolerance is ± 10 mV. The AD580 is recommended as a stable reference for all 8-, 10and 12-bit D-to-A converters that require an external reference. In addition, the wide input range of the AD580 allows operation with 5 volt logic supplies making the AD580 ideal for digital panel meter applications or whenever only a single logic power supply is available. The AD580J, K, L and M are specified for operation over the 0°C to +70°C temperature range; the AD580S, T and U are specified for operation over the extended temperature range of –55°C to +125°C. 2. The three-terminal voltage in/voltage out operation of the AD580 provides regulated output voltage without any external components. 3. The AD580 provides a stable 2.5 V output voltage for input voltages between 4.5 V and 30 V. The capability to provide a stable output voltage using a 5-volt input makes the AD580 an ideal choice for systems that contain a single logic power supply. 4. Thin-film resistor technology and tightly controlled bipolar processing provide the AD580 with temperature stabilities to 10 ppm/°C and long-term stability better than 250 µV. 5. The low quiescent current drain of the AD580 makes it ideal for CMOS and other low power applications. 6. The AD580 is available in versions compliant with MIL-STD-883. Refer to the Analog Devices Military Products Databook or current AD580/883B data sheet for detailed specifications. *Protected by Patent Nos. 3,887,863; RE30,586. REV. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 617/329-4700 Fax: 617/326-8703 AD580–SPECIFICATIONS (@ E Model Min AD580J Typ OUTPUT VOLTAGE TOLERANCE (Error from Nominal 2.500 Volt Output) OUTPUT VOLTAGE CHANGE TMIN to TMAX LINE REGULATION 7 V ≤ VIN ≤ 30 V 4.5 V ≤ VIN ≤ 7 V 1.5 0.3 LOAD REGULATION ∆I = 10 mA IN = +15 V and +258C ) Max Min AD580K Typ Max Min AD580L Typ Max AD580M Typ Max Min Units 675 625 610 610 mV 15 85 7 40 4.3 25 1.75 10 mV ppm/°C 4 2 2 1 2 1 mV mV 10 mV 1.5 mA 1.5 0.3 6 3 10 10 1.0 NOISE (0.1 Hz to 10 Hz) 8 8 8 8 µV (p-p) STABILITY Long Term Per Month 250 25 250 25 250 25 250 25 µV µV TEMPERATURE PERFORMANCE Specified Operating Storage 0 –55 –65 PACKAGE OPTION* TO-52 (H-03A) 1.0 10 QUIESCENT CURRENT 1.5 +70 +125 +175 0 –55 –65 AD580JH Model Min OUTPUT VOLTAGE CHANGE TMIN to TMAX LINE REGULATION 7 V ≤ VIN ≤ 30 V 4.5 V ≤ VIN ≤ 7 V 1.5 0.3 LOAD REGULATION ∆I = 10 mA +70 +125 +175 0 –55 –65 AD580KH AD580S Typ Max OUTPUT VOLTAGE TOLERANCE (Error from Nominal 2.500 Volt Output) 1.0 1.5 Min AD580T Typ Max 1.0 1.5 +70 +125 +175 0 –55 –65 AD580LH Min +70 +125 +175 AD580MH AD580U Typ Max Units 625 610 610 mV 25 55 11 25 4.5 10 mV ppm/°C 6 3 2 1 2 1 mV mV 10 10 10 mV 1.5 mA QUIESCENT CURRENT 1.0 NOISE (0.1 Hz to 10 Hz) 8 8 8 µV (p-p) STABILITY Long Term Per Month 250 25 250 25 250 25 µV µV TEMPERATURE PERFORMANCE Specified Operating Storage PACKAGE OPTION* TO-52 (H-03A) –55 –55 –65 +125 +150 +175 AD580SH 1.0 1.5 –55 –55 –65 1.0 1.5 +125 +150 +175 AD580TH –55 –55 –65 °C °C °C +125 +150 +175 °C °C °C AD580UH NOTES *H = Metal Can. Specifications subject to change without notice. Specifications shown in boldface are tested on all production units at final electrical test. Results from those tests are used to calculate outgoing quality levels. All min and max specifications are guaranteed, although only those shown in boldface are tested on all production units. –2– REV. A AD580 ABSOLUTE MAXIMUM RATINGS THEORY OF OPERATION Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 V Power Dissipation @ +25°C Ambient Temperature . . . . . . . . . . . . . . . . . . . . . . . 350 mW Derate above +25°C . . . . . . . . . . . . . . . . . . . . . . . 2.8 mW/°C Lead Temperature (Soldering 10 sec) . . . . . . . . . . . . . +300°C Thermal Resistance Junction-to-Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100°C Junction-to-Ambient . . . . . . . . . . . . . . . . . . . . . . . 360°C/W The AD580 family (AD580, AD581, AD584, AD589) uses the “bandgap” concept to produce a stable, low temperature coefficient voltage reference suitable for high accuracy data acquisition components and systems. The device makes use of the underlying physical nature of a silicon transistor base-emitter voltage in the forward-biased operating region. All such transistors have approximately a –2 mV/°C temperature coefficient, unsuitable for use directly as a low TC reference; however, extrapolation of the temperature characteristic of any one of these devices to absolute zero (with emitter current proportional to absolute temperature) reveals that it will go to a VBE of 1.205 volts at 0K, as shown in Figure 1. Thus, if a voltage could be developed with an opposing temperature coefficient to sum with VBE to total 1.205 volts, a zero-TC reference would result and operation from a single, low voltage supply would be possible. The AD580 circuit provides such a compensating voltage, V1 in Figure 2, by driving two transistors at different current densities and amplifying the resulting VBE difference (∆VBE—which now has a positive TC); the sum (VZ) is then buffered and amplified up to 2.5 volts to provide a usable reference-voltage output. Figure 3 is the schematic diagram of the AD580. AD580 CHIP DIMENSIONS AND PAD LAYOUT Dimensions shown in inches and (mm). The AD580 operates as a three-terminal reference, which means that no additional components are required for biasing or current setting. The connection diagram, Figure 4 is quite simple. The AD580 is also available in chip form. Consult the factory for specifications and applications information. Figure 1. Extrapolated Variation of Base-Emitter Voltage with Temperature (IEαT), and Required Compensation, Shown for Two Different Devices Figure 2. Basic Bandgap-Reference Regulator Circuit REV. A –3– AD580 Figure 5. Typical AD580K Output Voltage vs. Temperature The AD580M guarantees a maximum deviation of 1.75 mV over the 0°C to +70°C temperature range. This can be shown to be equivalent to 10 ppm/°C average maximum; i.e., Figure 3. AD580 Schematic Diagram 1.75 mV max 1 × =10 ppm/°C max average 70°C 2.5V The AD580 typically exhibits a variation of 1.5 mV over the power supply range of 7 volts to 30 volts. Figure 6 is a plot of AD580 line rejection versus frequency. NOISE PERFORMANCE Figure 7 represents the peak-to-peak noise of the AD580 from 1 Hz (3 dB point) to a 3 dB high end shown on the horizontal axis. Peak-to-peak noise from 1 Hz to 1 MHz is approximately 600 µV. Figure 4. AD580 Connection Diagram VOLTAGE VARIATION VS. TEMPERATURE Some confusion exists in the area of defining and specifying reference voltage error over temperature. Historically, references are characterized using a maximum deviation per degree Centigrade; i.e., 10 ppm/°C. However, because of the inconsistent nonlinearities in Zener references (butterfly or “S” type characteristics), most manufacturers use a maximum limit error band approach to characterize their references. This technique measures the output voltage at 3 to 5 different temperatures and guarantees that the output voltage deviation will fall within the guaranteed error band at these discrete temperatures. This approach, of course, makes no mention or guarantee of performance at any other temperature within the operating temperature range of the device. Figure 6. AD580 Line Rejection Plot The consistent Voltage vs. Temperature performance of a typical AD580 is shown in Figure 5. Note that the characteristic is quasi-parabolic, not the possible “S” type characteristics of classical Zener references. This parabolic characteristic permits a maximum output deviation specification over the device’s full operating temperature range, rather than just at 3 to 5 discrete temperatures. Figure 7. Peak-to-Peak Output Noise vs. Frequency –4– REV. A AD580 THE AD580 AS A LOW POWER, LOW VOLTAGE PRECISION REFERENCE FOR DATA CONVERTERS The AD580 has a number of features that make it ideally suited for use with A/D and D/A data converters used in complex microprocessor-based systems. The calibrated 2.500 volt output minimizes user trim requirements and allows operation from a single low voltage supply. Low power consumption (1 mA quiescent current) is commensurate with that of CMOS-type devices, while the low cost and small package complements the decreasing cost and size of the latest converters. Figure 8. Input Current vs. Input Voltage (Integral Loads) THE AD580 AS A CURRENT LIMITER The AD580 represents an excellent alternative to current limiter diodes which require factory-selection to achieve a desired current. This approach often results in temperature coefficients of 1%/°C. The AD580 approach is not limited to a specially selected factory set current limit; it can be programmed from 1 mA to 10 mA with the insertion of a single external resistor. The approximate temperature coefficient of current limit for the AD580 used in this mode is 0.13%/°C for ILIM = 1 mA and 0.01%/°C for ILIM = 13 mA (see Figure 9). Figure 8 displays the high output impedance of the AD580 used as a current limiter for ILIM = 1, 2, 3, 4, 5 mA. Figure 10 shows the AD580 used as a reference for the AD7542 12-bit CMOS DAC with complete microprocessor interface. The AD580 and the AD7542 are specified to operate from a single 5 volt supply; this eliminates the need to provide a +15 volt power supply for the sole purpose of operating a reference. The AD7542 includes three 4-bit data registers, a 12-bit DAC register, and address decoding logic; it may thus be interfaced directly to a 4-, 8- or 16-bit data bus. Only 8 mA of quiescent current from the single +5 volt supply is required to operate the AD7542 which is packaged in a small 16-pin DIP. The AD544 output amplifier is also low power, requiring only 2.5 mA quiescent current. Its laser-trimmed offset voltage preserves the ± 1/2 LSB linearity of the AD7542KN without user trims and it typically settles to ± 1/2 LSB in less than 3 µs. It will provide the 0 volt to –2.5 volt output swing from ± 5 volt supplies. Figure 9. A Two-Component Precision Current Limiter Figure 10. Low Power, Low Voltage Reference for the AD7542 Microprocessor-Compatible 12-Bit DAC REV. A –5– AD580 OUTLINE DIMENSIONS Dimensions shown in inches and (mm). PRINTED IN U.S.A. C549a–4–8/85 TO-52 Package –6– REV. A