Continental Device India Limited An ISO/TS16949 and ISO 9001 Certified Company PNP EPITAXIAL PLANAR SILICON TRANSISTOR CSA1015 TO-92 Plastic Package E CB Audio Frequency General Purpose and Driver Stage Amplifier Applications. Complementary CSC1815 ABSOLUTE MAXIMUM RATINGS (Ta=25ºC unless specified otherwise) DESCRIPTION SYMBOL VCBO Collector Base Voltage VALUE 50 UNITS V Collector Emitter Voltage VCEO 50 V Emitter Base Voltage VEBO 5 V Collector Current Continuous IC 150 mA Base Current IB 50 mA Collector Power Dissipation PC 625 mW Tj, Tstg -55 to +125 ºC Rth(j-c) 250 ºC/W Operating And Storage Junction Temperature Range THERMAL RESISTANCE Junction to case ELECTRICAL CHARACTERISTICS (Ta=25ºC unless specified otherwise) DESCRIPTION SYMBOL TEST CONDITION ICBO VCB =50V, IE=0 Collector Cut off Current IEBO VEB=5V, IC = 0 Emitter Cut off Current DC Current Gain Collector Emitter Saturation Voltage Base Emitter Saturation Voltage *hFE IC =2mA, VCE=6V 70 hFE IC =150mA, VCE=6V 25 VCE(sat) VBE(sat) TYP ft Collector Output Capacitance Cob Base Spreading Resistance rbb' Noise Figure NF VCE=10V, IC=1mA, f=100MHz VCB=10V,IE=0, f=1MHz VCB=10V, IE=1mA, f=30MHz VCE=6V, IC=0.1mA, O 70 - 140 Rg=10Kohms, f=1KHz Y 120 - 240 MAX 100 UNITS nA 100 nA 400 IC=100mA,IB= 10mA IC=100mA,IB= 10mA DYNAMIC CHARACTERISTICS Transition Frequency CLASSIFICATION *hFE MIN 0.30 1.1 80 V V MHz 7.0 pF Ω 30 10 dB GR 200 - 400 CSA1015REV_5 281202D Continental Device India Limited Datasheet Page 1 of 4 CSA1015 TO-92 Plastic Package TO-92 Plastic Package A Uncontrolled 2 E 3 D MIN. 4.32 MAX. 5.33 B 4.45 3.18 5.20 4.19 0.41 0.55 0.35 0.50 E F 5 DEG G 1.14 1.40 1.20 1.40 H 12.70 K — 1.982 2.082 L M 1.03 1.20 All dimensions are in mm D K Beyond 'L' Solderability Ensured 1 DIM A C D L Dimension With 'L' B SEC AA A A G F C 3 2 1 H M F Mold Parting Line PIN CONFIGURATION 1. BASE 2. COLLECTOR 3. EMITTER 3 2 1 The TO-92 Package, Tape and Ammo Pack Drawings are correct as on the date of issue/revision of this Data Sheet. The currently valid dimensions and information, may please be confirmed from the TO-92 Drawing in the Packages and Packing Section of the Product Catalogue. Packing Details PACKAGE STANDARD PACK INNER CARTON BOX OUTER CARTON BOX Details Net Weight/Qty Size Qty Size Qty Gr Wt TO-92 Bulk 1K/polybag 200 gm/1K pcs 3" x 7.5" x 7.5" 5K 17" x 15" x 13.5" 80K 23 kgs TO-92 T&A 2K/ammo box 645 gm/2K pcs 12.5" x 8" x 1.8" 2K 17" x 15" x 13.5" 32K 12.5 kgs CSA1015REV_5 281202D Continental Device India Limited Datasheet Page 2 of 4 CSA1015 TO-92 Plastic Package TO-92 Tape and Ammo Pack Tape Mechanical Data h (p) P T h h1 Ammo Pack Style Adhesive Tape on Top Side h1 A1 D FEE Flat side A H3 H2 Label C1 H1 Ho 186 (7.3") W2 C2 Wo L Carrier Strip W1 W F1 F2 Do (1 332 F t1 (1. 43 7") P2 t Po 3") Flat Side of Transistor and Adhesive Tape Visible 2000 pcs./Ammo Pack All dimensions are in mm ITEM BODY WIDTH BODY HEIGHT BODY THICKNESS PITCH OF COMPONENT * 1 FEED HOLE PITCH * 2 FEED HOLE CENTRE TO COMPONENT CENTRE DISTANCE BETWEEN OUTER LEADS * 3 COMPONENT ALIGNMENT SIDE VIEW * 4 COMPONENT ALIGNMENT FRONT VIEW TAPE WIDTH HOLD-DOWN TAPE WIDTH HOLE POSITION HOLD-DOWN TAPE POSITION LEAD WIRE CLINCH HEIGHT COMPONENT HEIGHT LENGTH OF SNIPPED LEADS FEED HOLE DIAMETER * 5 TOTAL TAPE THICKNESS LEAD - TO - LEAD DISTANCE STAND OFF CLINCH HEIGHT LEAD PARALLELISM PULL - OUT FORCE SPECIFICATION SYMBOL A1 A T P Po MIN. NOM. MAX. 4.0 4.8 3.9 TOL . NOTES 4.8 5.2 4.2 1. Maximum alignment deviation between leads will not to be greater than 0.2mm. 12.7 12.7 ± 1.0 ± 0.3 2. Maximum non-cumulative variation between tape feed holes shall not exceed 1 mm in 20 pitches. P2 6.35 ± 0.4 F 5.08 + 0.6 - 0.2 3. Holddown tape will not exceed beyond the edge(s) of carrier tape and there shall be no exposure of adhesive. h h1 W Wo W1 0 0 18 6 9 W2 Ho H1 L Do t F1, F2 0.5 16 H2 H3 | C1 - C2 | (p) 1.0 1.3 ± 0.5 ± 0.2 + 0.7 - 0.5 ± 0.2 ± 0.5 4. There will be no more than three (3) consecutive missing components in a tape. 5. A tape trailer, having at least three feed holes are provided after the last component in a tape. 6. Splices should not interfere with the sprocket feed holes. 23.25 11.0 4 ± 0.2 1.2 2.54 0.45 6N 1.45 3.0 0.22 + 0.4 - 0.1 REMARKS * 1 Cumulative pitch error 1.0 mm/20 pitch * 2 To be measured at bottom of clinch * 3 At top of body * 4 At top of body * 5 t1 0.3 – 0.6 mm CSA1015REV_5 281202D Continental Device India Limited Datasheet Page 3 of 4 Notes CSA1015 TO-92 Plastic Package Disclaimer The product information and the selection guides facilitate selection of the CDIL's Discrete Semiconductor Device(s) best suited for application in your product(s) as per your requirement. It is recommended that you completely review our Data Sheet(s) so as to confirm that the Device(s) meet functionality parameters for your application. The information furnished in the Data Sheet and on the CDIL Web Site/CD are believed to be accurate and reliable. CDIL however, does not assume responsibility for inaccuracies or incomplete information. Furthermore, CDIL does not assume liability whatsoever, arising out of the application or use of any CDIL product; neither does it convey any license under its patent rights nor rights of others. These products are not designed for use in life saving/support appliances or systems. CDIL customers selling these products (either as individual Discrete Semiconductor Devices or incorporated in their end products), in any life saving/support appliances or systems or applications do so at their own risk and CDIL will not be responsible for any damages resulting from such sale(s). CDIL strives for continuous improvement and reserves the right to change the specifications of its products without prior notice. CDIL is a registered Trademark of Continental Device India Limited C-120 Naraina Industrial Area, New Delhi 110 028, India. Telephone + 91-11-2579 6150, 5141 1112 Fax + 91-11-2579 5290, 5141 1119 [email protected] www.cdilsemi.com CSA1015REV_5 281202D Continental Device India Limited Datasheet Page 4 of 4